Technical Service Bulletins (TSBs) for the 2018 Savana are official communications between GMC & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin provides repair information to correct a customer concern of no start, hard start with belt squeal, belt break, loss of power steering and/or power brake assist. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides repair information to correct a customer concern of no start, hard start with belt squeal, belt break, loss of power steering and/or power brake assist. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides a procedure on applying seam sealer to a joint within the engine bay to stop a water leak that may have caused one of the following No Start, Hard Start with Belt Squeal, Belt Break, Loss of Power Steering ... Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This Preliminary information communicates if an intermittent c0050 Sym0f occurs on a van with dual rear wheels. Engineering is currently investigating concern and no repairs are to be made at this time. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides repair information to correct a customer concern of no start, hard start with belt squeal, belt break, loss of power steering and/or power brake assist. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication provides information to the technician about the operation and diagnostics of the Regular Production Option Code UJ1 brake warning pressure warning system. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This technical bulletin provides repair information to correct a customer concern of no start, hard start with belt squeal, belt break, loss of power steering and/or power brake assist. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the operation and diagnostics of the Regular Production Option Code UJ1 brake warning pressure warning system. Read More »
This Preliminary Information communication provides information to the technician about the operation and diagnostics of the Regular Production Option Code UJ1 brake warning pressure warning system. Read More »
This technical bulletin provides a procedure on applying seam sealer to a joint within the engine bay to stop a water leak that may have caused one of the following No Start, Hard Start with Belt Squeal, Belt Break, Loss of Power Steering ... Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC
18316 - Customer Satisfaction Program. Certain 2018 model year Chevrolet Express and GMC Savana vehicles, equipped with 4 wheel disc brakes, may have a condition where when the right rear wheel is driven over rumble strips a vibration in ... Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP
This Preliminary information communicates if an intermittent c0050 Sym0f occurs on a van with dual rear wheels. Engineering is currently investigating concern and no repairs are to be made at this time. Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT
This Preliminary Information communication provides information to the technician about the operation and diagnostics of the Regular Production Option Code UJ1 brake warning pressure warning system. Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR
18316 - Customer Satisfaction Program. Certain 2018 model year Chevrolet Express and GMC Savana vehicles, equipped with 4 wheel disc brakes, may have a condition where when the right rear wheel is driven over rumble strips a vibration in ... Read More »
18316 - Customer Satisfaction Program. Certain 2018 model year Chevrolet Express and GMC Savana vehicles, equipped with 4 wheel disc brakes, may have a condition where when the right rear wheel is driven over rumble strips a vibration in ... Read More »
18316 - Customer Satisfaction Program. Certain 2018 model year Chevrolet Express and GMC Savana vehicles, equipped with 4 wheel disc brakes, may have a condition where when the right rear wheel is driven over rumble strips a vibration in ... Read More »
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended, causing the parking pawl to engage while driving. Read More »
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on. Read More »
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended, causing the parking pawl to engage while driving. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This technical bulletin provides repair information to correct a customer concern of Lack of Power or Poor Performance During High Ambient Temperatures with RPO (C7N) 12,300 LB GVWR or (C4M) 9,900 LB GVWR. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This technical bulletin provides repair information to correct a customer concern of no start, hard start with belt squeal, belt break, loss of power steering and/or power brake assist. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2018-2019 model year diesel engine vehicles. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition. Read More »
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication advises the technician that the ECM part numbers 55501366, 55502052 and 55485591 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years. Read More »
This technical bulletin provides a procedure on applying seam sealer to a joint within the engine bay to stop a water leak that may have caused one of the following No Start, Hard Start with Belt Squeal, Belt Break, Loss of Power Steering ... Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option ... Read More »
This Preliminary Information communication advises the technician that the ECM part numbers 55501366, 55502052 and 55485591 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This technical bulletin provides repair information to correct a customer concern of no start, hard start with belt squeal, belt break, loss of power steering and/or power brake assist. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid ... Read More »
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp ... Read More »
This informational bulletin explains how the SOOT readings went from grams to percentage. 2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section. Read More »
This Preliminary information communicates A vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm. Read More »
This diagnostic tip provides information to the tech to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away. Read More »
This Preliminary information communicates A vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm. Read More »
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp ... Read More »
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger Whine Noise due to the blades on the turbo being bent. Read More »
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp ... Read More »
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger Whine Noise due to the blades on the turbo being bent. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp ... Read More »
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger Whine Noise due to the blades on the turbo being bent. Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:SEALS/GASKETS
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp ... Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin explains how the SOOT readings went from grams to percentage. 2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This Preliminary Information communication provides information to the technician that some vehicle may have an “Exhaust Fluid Quality Poor” on the Driver Information Center or a diesel exhaust fluid warning lamp on or other ... Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be Set. Read More »
This Technical bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This technical bulletin provides to the technician a possible issue with the NOx sensor wiring harness and what to do if corrosion is found. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This Technical Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2018-2019 model year diesel engine vehicles. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension housing and to perform testing on transmission for other possible issues, but it still may be possible on high ... Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if found the cause of the customer's concern. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Delayed and/or Harsh Engagement of Transmission Shift After Vehicle Sitting with Engine Off. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension housing and to perform testing on transmission for possible other issues, but it still may be possible on high mile ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This information advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF causing the customers concern. Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This informational bulletin advises the technician of possibly installing the incorrect 1-2-7-8-R clutch fluid passage seal and which seal should be used with measurements of the seal. Read More »
This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This bulletin provides a procedure to replace the shifter cable, lever and bracket if the shifter at the lever located at the trans, has popped off. Read More »
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger Whine Noise due to the blades on the turbo being bent. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This Preliminary information communicates some customers may comment that the vehicle exhibits a lack of power when driving up grades or after the vehicle has been idling for long periods of time in high ambient temperatures (90 degrees ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This technical bulletin provides a repair procedure to correct a customer concern of Delayed and/or Harsh Engagement of Transmission Shift After Vehicle Sitting with Engine Off. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended, causing the parking pawl to engage while driving. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This engineering information bulletin ends the need for information from the field on an Intermittent No Forward and/or No Reverse While Driving condition. If this condition is encountered, refer to SI for further diagnosis. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed. Read More »
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option ... Read More »
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as attended causing the parking pawl to engage while driving. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician that a whine noise heard from the automatic transmission fluid pan hear with the the key on and engine off, or for up to one minute after the vehicle has ... Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has ended the part restriction for the T87A Transmission Control Module. Read More »
This technical bulletin provides a procedure on applying seam sealer to a joint within the engine bay to stop a water leak that may have caused one of the following No Start, Hard Start with Belt Squeal, Belt Break, Loss of Power Steering ... Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option ... Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
This Preliminary Information communication provides information to the technician about vehicles that have a random bump, chuggle, or fishbite sensation when crowding the throttle slightly with the Torque Converter Clutch on while ... Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides repair information to correct a customer concern of no start, hard start with belt squeal, belt break, loss of power steering and/or power brake assist. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This technical bulletin provides a procedure to repair a possible wiring harness repair if damaged by the parking brake, brake booster mount or brake pedal bolt. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States. Read More »
This informational bulletin explains how the SOOT readings went from grams to percentage. 2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles proper operation of the stop and/or turn signals. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the dealer technician that if after replacing the valve body on an 8L45 or 8L90 transmission the vehicle will not move the valve body may be missing a plug and retainer bolt. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2016-2019 model year diesel engine vehicles. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2018-2019 model year diesel engine vehicles. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about the retained accessory power on vehicles with Radio Provisions Only Regular Production Option Code (UXZ). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication advises the technician that the restriciton on ECM part numbers 55501366, 55502052 and 55485591 has ended. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about vehicle that will not change Heater-Vent-Air Conditioning modes, Defrost or RECIRC positions. Read More »
18316 - Customer Satisfaction Program. Certain 2018 model year Chevrolet Express and GMC Savana vehicles, equipped with 4 wheel disc brakes, may have a condition where when the right rear wheel is driven over rumble strips a vibration in ... Read More »
18317 - Customer Satisfaction Program. Certain vehicles, equipped with RPOs 9C2, 9B9 or 9D7 may have a condition in which the programmed limiters of 65, 70 or 75 mph respectively, are not limiting the vehicle speed. Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern. Read More »
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar? Module Functionality After OnStar Module Replacement for Another Condition. Read More »
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
Diagnostic Tip for Malfunction Indicator Lamp (MIL) Illuminated - DTC P249D, P249E, U029D, U029E Set Some customers may comment that the MIL is illuminated. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
The information in this bulletin details the proper configurations for the ignition key, fob, key tags, key rings, key ring sizes and applying a QR code sticker or barcode sticker to a key fob. Read More »
This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Read More »
The information in this bulletin details the proper configurations for the ignition key, fob, key tags, key rings, key ring sizes and applying a QR code sticker or barcode sticker to a key fob. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary Information communication provides information to the technician about the operation and diagnostics of the Regular Production Option Code UJ1 brake warning pressure warning system. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use. Read More »
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed. Read More »
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles proper operation of the stop and/or turn signals. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles proper operation of the stop and/or turn signals. Read More »
This Preliminary Information communication provides information to the technician about vehicles proper operation of the stop and/or turn signals. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Drivers Door Window Glass Out of Channel and/or Inoperative. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Drivers Door Window Glass Out of Channel and/or Inoperative. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicle that will not change Heater-Vent-Air Conditioning modes, Defrost or RECIRC positions. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This Preliminary information communicates to the dealer technician to inspect for a missing 1-2-7-8-R clutch fluid passage seal or incorrect 1-2-7-8-R clutch fluid passage seal being install for a no movement concern after valve body ... Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, ... Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube ... Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube ... Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Drivers Door Window Glass Out of Channel and/or Inoperative. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
Prior to reinstallation of the outer dual rear wheels, ensure that the washers are removed and inspected wheel studs and lug nut threads for damage. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary information communicates if an intermittent c0050 Sym0f occurs on a van with dual rear wheels. Engineering is currently investigating concern and no repairs are to be made at this time. Read More »
Prior to reinstallation of the outer dual rear wheels, ensure that the washers are removed and inspected wheel studs and lug nut threads for damage. Read More »
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided. Read More »
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels. Read More »
Prior to reinstallation of the outer dual rear wheels, ensure that the washers are removed and inspected wheel studs and lug nut threads for damage. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
18189 - Customer Satisfaction Program. Certain 2018 model year Chevrolet Express and GMC Savana vehicles, may have a condition in which the chassis harness is misrouted between the body and the frame. Read More »
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger Whine Noise due to the blades on the turbo being bent. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Read More »
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube ... Read More »
This technical bulletin provides repair information to correct a customer concern of Lack of Power or Poor Performance During High Ambient Temperatures with RPO (C7N) 12,300 LB GVWR or (C4M) 9,900 LB GVWR. Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary information communicates some customers may comment that the vehicle exhibits a lack of power when driving up grades or after the vehicle has been idling for long periods of time in high ambient temperatures (90 degrees ... Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger Whine Noise due to the blades on the turbo being bent. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp ... Read More »
This informational bulletin explains how the SOOT readings went from grams to percentage. 2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section. Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This technical bulletin advised the technician to take the vehicle for a test drive to validate a possible normal TCC performance while under heavy specific driving maneuvers. Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary Information communication provides information to the technician about the retained accessory power on vehicles with Radio Provisions Only Regular Production Option Code (UXZ). Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC. Read More »
This technical bulletin provides repair information to correct a customer concern of the air conditioning changes intermittently, from blowing cold to blowing warm air. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication advises the technician that the restriciton on ECM part numbers 55501366, 55502052 and 55485591 has ended. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication advises the technician that the ECM part numbers 55501366, 55502052 and 55485591 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication provides information to the technician about the retained accessory power on vehicles with Radio Provisions Only Regular Production Option Code (UXZ). Read More »
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program. Read More »
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, ... Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be Set. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport ... Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4). Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Read More »
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
The PI was created to advise of an engineering investigation for a concern of unable to connect toOnStar Virtual Advisor when selecting "New Destination" in the OnStar menu. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ... Read More »
This Preliminary Information communication provides information to the technician about the retained accessory power on vehicles with Radio Provisions Only Regular Production Option Code (UXZ). Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This informational bulletin provides information on Light and Medium Duty Truck Product Identification and Warranty Summary Chevrolet/GMC Dealers. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This Preliminary Information communication advises the technician that the Product Quality Center part restriction has ended for the 8L45 and 8L90 park actuator rod. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months). Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the 8L45 and 8L90 park actuator rod. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded on the ECM or and detection of a power up hardware installed. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger Whine Noise due to the blades on the turbo being bent. Read More »
This informational bulletin explains how the SOOT readings went from grams to percentage. 2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2016-2019 model year diesel engine vehicles. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, ... Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicle that will not change Heater-Vent-Air Conditioning modes, Defrost or RECIRC positions. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
