Technical Service Bulletins (TSBs) for the 2019 Trax are official communications between Chevrolet & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 and/or U1814-02 Set will not Clear, Blown Fuse F6DA, Rejected by Control Module Error ... Read More »
This service bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 and/or U1814-02 Set will not Clear, Blown Fuse F6DA, Rejected by Control Module Error ... Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 and/or U1814-02 Set will not Clear, Blown Fuse F6DA. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, B1529 SYM03. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, P1529 SYM03. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Technical bulletin provides information on replacing both inner and outer intermediate steering shaft boots and steering gear due to water intrusion in the steering gear input shaft freezing and/or corrosion causing a hard to steer ... Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
A192221650 - Service Update Bulletin. Certain vehicles may not have had a wheel alignment performed after receiving a strut replacement at the port. Read More »
This informational bulletin provides information for the customer to pair their phone in order for the push to talk button on the steering wheel control to work. Read More »
This bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 Set will not Clear, Blown Fuse F9DA. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
A192221650 - Service Update Bulletin. Certain vehicles may not have had a wheel alignment performed after receiving a strut replacement at the port. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This technical bulletin provides a procedure to replace the lower control arms if they were found contacting the cradle and making noise, and were previously replaced. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that had the Brake Pressure Modulator Valve now Diagnostic Trouble Code C0131 is set current. Read More »
This Preliminary Information communication provides information to the technician about vehicles that had the Brake Pressure Modulator Valve now Diagnostic Trouble Code C0131 is set current. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that had the Brake Pressure Modulator Valve now Diagnostic Trouble Code C0131 is set current. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position. Read More »
This informational bulletin provides information for dealers and technicians about the 1.4L and 1.8L turbocharged engines that use two different suppliers for the oil filter housing, which results in two different filters being used. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This technical bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL On from happening again. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This informational bulletin provides information to the tech to test the PCV for proper performance before replacing the camshaft cover to correct a MIL On w/DTC P0171. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This informational bulletin explains to the technician to inspect the pistons for damage and not just replace the engine assembly if the pistons are the only cause of damage. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This service bulletin provides diagnostic/repair information to correct customer concerns of a Crank No Start or Extended Crank, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides a repair procedure to correct customer concerns of Poor Engine Performance in Extremely Cold Weather Conditions, PCV Bypass Hose and Charge Air Cooler Icing for LUV Engines, Malfunction Indicator Lamp (MIL) ... Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
Service Update. Certain vehicles may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18A?C (0A?F) or ... Read More »
This service bulletin provides information on a normal characteristic of a transmission that will not shift into overdrive range during cold ambient temperatures. Read More »
This service bulletin provides a service procedure to correct customer concerns of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
Service Update. Certain vehicles may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18A?C (0A?F) or ... Read More »
This service bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
Service Update. Certain vehicles listed above may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18A?C ... Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL Illuminated. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This service bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides a repair procedure to correct customer concerns of Poor Engine Performance in Extremely Cold Weather Conditions, PCV Bypass Hose and Charge Air Cooler Icing for LUV Engines, Malfunction Indicator Lamp (MIL) ... Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides a repair procedure to correct customer concerns of Poor Engine Performance in Extremely Cold Weather Conditions, PCV Bypass Hose and Charge Air Cooler Icing for LUV Engines, Malfunction Indicator Lamp (MIL) ... Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential restriction and blockage in the induction system creating drive ability issues. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides repair information to correct a customer concern of Service All Wheel Drive (AWD)/Service Stability Messages and/or Low Oil Pressure Shut Off Engine Message Displayed on Driver Information Center (DIC), ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Oil Leaking from Front of Engine. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential restriction and blockage in the induction system creating drive ability issues. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This technical bulletin provides a procedure on locating and repairing a possible short to ground at the G100 ground stud and engine wiring harness to correct Service AWD/Service Stability messages on DIC, MIL with DTCs. Read More »
Special Coverage Adjustment. Certain vehicles, there may be a coolant leak at the radiator. Dealers are to replace condenser, radiator, fan, charge air cooler and piping, and A/C pipes. Read More »
Special Coverage - certain vehicles there may be a coolant leak at the radiator. Dealers are to replace condenser, radiator, fan, charge air cooler and piping, and A/C pipes. Read More »
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This technical bulletin provides a procedure to repair the mechanical components and then be sure to reprogram the throttle body to prevent the conditions of a rough running engine, MIL On from happening again. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This Preliminary Information communication provides information to the technician about improper engine block cleaning during engine block service could lead to lines in the block deck surface that may be mistaken for cracks. Read More »
This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
This service bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This service bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This bulletin provides information for the low oil pressure light on at idle, which may be caused by oil pressure being bled off due to debris in the oil drain check valve and/or a smashed oil filter. Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides diagnostic/repair information to correct customer concerns of a Crank No Start or Extended Crank, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This informational bulletin provides information for dealers and technicians about the 1.4L and 1.8L turbocharged engines that use two different suppliers for the oil filter housing, which results in two different filters being used. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin advises the technician to replace the rear diff carrier if heavy corrosion caused noise, cracking and/or leaking to correct customer concerns of Clunk or Growl Noise Coming from Rear of Vehicle and/or Rear End ... Read More »
This service bulletin provides information on a normal characteristic of a transmission that will not shift into overdrive range during cold ambient temperatures. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information on a normal characteristic of a transmission that will not shift into overdrive range during cold ambient temperatures. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This technical bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL On from happening again. Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This technical bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL On from happening again. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE
This Preliminary Information communication advises the technician of a normal characteristic of the neutral idle feature on a 6T40 transmission Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary information communicates to the technician the need to inspect connector for moisture intrusion at ECM, procedure for verification of need for replacement Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This service bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL Illuminated. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 and/or U1814-02 Set will not Clear, Blown Fuse F6DA, Rejected by Control Module Error ... Read More »
This service bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 and/or U1814-02 Set will not Clear, Blown Fuse F6DA, Rejected by Control Module Error ... Read More »
This service bulletin provides repair information to correct a customer concern of Service All Wheel Drive (AWD)/Service Stability Messages and/or Low Oil Pressure Shut Off Engine Message Displayed on Driver Information Center (DIC), ... Read More »
This service bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 and/or U1814-02 Set will not Clear, Blown Fuse F6DA. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States. Read More »
This service bulletin provides diagnostic/repair information to correct customer concerns of a Crank No Start or Extended Crank, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, P1529 SYM03. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position. Read More »
This technical bulletin provides a procedure on locating and repairing a possible short to ground at the G100 ground stud and engine wiring harness to correct Service AWD/Service Stability messages on DIC, MIL with DTCs. Read More »
This service bulletin provides information and a service procedure for dealers/technicians on OnStar Over the Air Update for TTY / TDD Operation and Continuous Improvement Changes. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp (MIL) illuminated, intermittent service messages, Erratic Gauges and technician finding DTCs U0073, U0121, U0100 and/or U0101 ... Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This technical bulletin provides a procedure on locating and repairing a possible short to ground at the G100 ground stud and engine wiring harness to correct Service AWD/Service Stability messages on DIC, MIL with DTCs. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp (MIL) illuminated, intermittent service messages, Erratic Gauges and technician finding DTCs U0073, U0121, U0100 and/or U0101 ... Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of over the air software update to resolve the concern. Read More »
This technical bulletin provides repair information to correct a customer concern of Intermittent OnStar Inoperative, DTC B101D-39, Red LED and Clock Date Time Inaccurate. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This technical bulletin provides a procedure to repair a possible short in the wiring harness where it enters through the bulkhead to correct Erratic IPC and Gauge Readings, an MIL and DTCs. Read More »
This informational bulletin provides information to the tech to test the PCV for proper performance before replacing the camshaft cover to correct a MIL On w/DTC P0171. Read More »
This technical bulletin provides a procedure to repair a possible short in the wiring harness where it enters through the bulkhead to correct Erratic IPC and Gauge Readings, an MIL and DTCs. Read More »
This informational bulletin provides information to the tech to test the PCV for proper performance before replacing the camshaft cover to correct a MIL On w/DTC P0171. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp (MIL) illuminated, intermittent service messages, and technician finding DTC?s U0073, U0121, U0100 and/or U0101 set. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This technical bulletin provides a procedure on locating and repair a possible short to ground at the G100 ground stud and engine wiring harness. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary information communicates that a customer may complain of when a Bluetooth call is received the ringing will be continuous for the rest of the drive cycle . Read More »
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info to retrieve while engineering completes further investigation. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info to retrieve while engineering completes further investigation. Read More »
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info to retrieve and of engineering investigation. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off. Read More »
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides repair information to correct a customer concern of passive entry and passive starting functions are always inoperative on one, or both, of the RKE Fobs, possible various DIC messages. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This Preliminary information communicates that a customer may complain of when a Bluetooth call is received the ringing will be continuous for the rest of the drive cycle . Read More »
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, B1529 SYM03. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, P1529 SYM03. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This technical bulletin provides a procedure to remove the driver front seat outboard seat back airbag and re-seat the CPA clip for the airbag. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Preliminary information communicates information for a technician to address a popping noise for missing spot welds on the drivers floor board. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This service bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL Illuminated. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This technical bulletin provides repair information to correct a customer concern of a musty odor, wet carpet and/or water leaking on the driver side floor. Read More »
This Preliminary information communicates to the dealer that during the PDI if they notice Insufficient hood to fender clearance to adjust the hood as needed. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary information communicates to the dealer that during the PDI if they notice Insufficient hood to fender clearance to adjust the hood as needed. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, B1529 SYM03. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
A192221650 - Service Update Bulletin. Certain vehicles may not have had a wheel alignment performed after receiving a strut replacement at the port. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, B1529 SYM03. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides information for dealers/technicians on Handsfree Apple Iphone Call Static conditions equipped with IOB Radio. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 and/or U1814-02 Set will not Clear, Blown Fuse F6DA, Rejected by Control Module Error ... Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, B1529 SYM03. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides diagnostic/repair information to correct customer concerns of a Crank No Start or Extended Crank, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides repair information to correct customer concerns of Unwanted Front Windshield Wiper Swipe, Cruise Control Wont Turn On, Steering Wheel Controls Inoperative, DTCs P155A SYM00, P1529 SYM03. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This bulletin provides a procedure to replace the BCM and PSCM to correct a condition of Service Power Steering Message Displayed, U0100 Set will not Clear, Blown Fuse F9DA. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
Special Coverage Adjustment. Certain vehicles, there may be a coolant leak at the radiator. Dealers are to replace condenser, radiator, fan, charge air cooler and piping, and A/C pipes. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This informational bulletin provides information for dealers and technicians about the 1.4L and 1.8L turbocharged engines that use two different suppliers for the oil filter housing, which results in two different filters being used. Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp (MIL) illuminated, intermittent service messages, Erratic Gauges and technician finding DTCs U0073, U0121, U0100 and/or U0101 ... Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides repair information to correct a customer concern of a musty odor, wet carpet and/or water leaking on the driver side floor. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary information communicates that a customer may complain of when a Bluetooth call is received the ringing will be continuous for the rest of the drive cycle . Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary information communicates that a customer may complain of when a Bluetooth call is received the ringing will be continuous for the rest of the drive cycle . Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin provides information for dealers/technicians on a blank or distorted 7 inch radio display during radio replacement. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary information communicates the location of the antenna during the Pre-Delivery Inspection process. Technician will find the antenna on the left hand trim pocket. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info to retrieve while engineering completes further investigation. Read More »
This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This informational bulletin provides information for the customer to pair their phone in order for the push to talk button on the steering wheel control to work. Read More »
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info to retrieve while engineering completes further investigation. Read More »
This Preliminary information communicates that engineering is aware of the radio RAP staying on concern and to replace the TCICM to resolve the concern. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL On from happening again. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary Information communicates to the dealer that if DTC P0496 continues to set after performing Strategy Based Diagnostics, the current customers drive cycle as this may contribute to the concern. Read More »
This bulletin provides information for the low oil pressure light on at idle, which may be caused by oil pressure being bled off due to debris in the oil drain check valve and/or a smashed oil filter. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp (MIL) illuminated, intermittent service messages, Erratic Gauges and technician finding DTCs U0073, U0121, U0100 and/or U0101 ... Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin provides a procedure to install a PCV heater or a charge air cooler to correct the turbo charger system from freezing causing cold weather performance issues. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. Read More »
This technical bulletin provides a procedure to replace the lower control arms if they were found contacting the cradle and making noise, and were previously replaced. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin explains to the technician to inspect the pistons for damage and not just replace the engine assembly if the pistons are the only cause of damage. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary information communicates that a customer may complain of when a Bluetooth call is received the ringing will be continuous for the rest of the drive cycle . Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
Special Coverage Adjustment. Certain vehicles, there may be a coolant leak at the radiator. Dealers are to replace condenser, radiator, fan, charge air cooler and piping, and A/C pipes. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0171 and or P1101 set. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
