Technical Service Bulletins (TSBs) for the 2020 Silverado 1500 are official communications between Chevrolet & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin advises the technician of a possible loose ground that may be causing customer concerns of Loss of Steering Assist and/or Loss of Brake Assist and Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This Preliminary information communicates a diagnostic tip to inspect the main ground connection when diagnosing any lack of power steering assist issues with DTCs C1597 and/or C1599. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to a Popping Noise Heard On Hard Turns and/or Going Over Speed Bumps, Creaking Noise While Turning Wheel Left and/or Right, Clicking ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a rubbing type noise heard while turning the steering wheel. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This technical bulletin provides repair information to correct a customer concern of Intermittent "Service Steering Column Lock" message displayed with U0155 Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Intermittent "Service Steering Column Lock" message displayed with U0155 Set. Read More »
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin advises the technician of a possible loose ground that may be causing customer concerns of Loss of Steering Assist and/or Loss of Brake Assist and Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak and/or clunking noise coming from the rear of the vehicle. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak and/or clunking noise coming from the rear of the vehicle. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This engineering information (EI) closure ends the need for gathering information from technicians in regards to the front upper control arm ball joint separated from the socket. Read More »
This engineering information (EI) closure ends the need for gathering further information from technicians in regards to the front upper control arm ball joint separated from the socket. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the front upper control arm ball joint separated from the socket. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the front upper control arm ball joint separated from the socket. Read More »
This Preliminary information communicates A vehicle may have a concern of a vibration or drone around 40 MPH and 1200 RPM under a light load. Debris in the tranmission mount. Inspect the transmission mount for debris. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to a Popping Noise Heard On Hard Turns and/or Going Over Speed Bumps, Creaking Noise While Turning Wheel Left and/or Right, Clicking ... Read More »
This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak and/or clunking noise coming from the rear of the vehicle. Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a vibration and/or banging noise heard from under the vehicle. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY:HANGER/BRACKET
This technical bulletin provides repair information to correct a customer concern of a squeak and/or clunking noise coming from the rear of the vehicle. Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This bulletin provides a procedure to correct a customer concern that while driving at low speeds, the rear wheels lock up, causing vehicle to come to a stop as if the brakes were applied or the vehicle was shifted into park. Read More »
This service bulletin provides information to dealership personnel that after performing a brake inspection, brake pad replacement, or any other repair that requires the caliper piston to be reseated may be causing DTC C05B0 to falsely ... Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing ?D? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or 8-6 ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on a tick and/or ping type noise heard from the Propeller Shaft during ... Read More »
This Preliminary information communicates that after installation of GM Accessory Performance Brake Pads it may be noticed the EBCM has set DTC(s) C116C 05 and/or C116B 05. Read More »
This technical bulletin provides repair information to correct a customer concern of Loss of Brake Assist, Various Messages Displayed in Driver Information Center (DIC), Brake Pedal Travel and Apply May Feel Different, One or More of the ... Read More »
This Preliminary information communicates that after installation of GM Accessory Performance Brake Pads it may be noticed the EBCM has set DTC(s) C116C 05 and/or C116B 05. Read More »
This technical bulletin provides repair information to correct a customer concern of Loss of Brake Assist, Various Messages Displayed in DIC, Brake Pedal Travel and Apply May Feel Different, DTC C0024 Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Loss of Brake Assist, Various Messages Displayed in DIC, Brake Pedal Travel and Apply May Feel Different, DTC C0024 Set. Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering released updated cals for the BSCM to repair the issue. Read More »
This technical bulletin provides repair information to correct a customer concern of Loss of Brake Assist, Various Messages Displayed in DIC, Brake Pedal Travel and Apply May Feel Different, DTC C0024 Set. Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering is working on updated cals for the BSCM. Read More »
This Preliminary information communicates repair information on Service Brake System, Reduced Engine Power, and Speed Limited messages on the DIC. Along with these messages, a SES MIL will be on and the brake pedal may feel hard. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This service bulletin advises the technician of a possible loose ground that may be causing customer concerns of Loss of Steering Assist and/or Loss of Brake Assist and Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides information to dealership personnel that after performing a brake inspection, brake pad replacement, or any other repair that requires the caliper piston to be reseated may be causing DTC C05B0 to falsely ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin advises the technician of a possible loose ground that may be causing customer concerns of Loss of Steering Assist and/or Loss of Brake Assist and Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This Preliminary information communicates the possibility of a misfire or rough running concern and abnormal engine noise due to excessive wear in exhaust roller follower axle pin. Read More »
This Preliminary information communicates the possibility of dtc p06DD due to low or no oil pressure immediately following engine oil and filter change due to oil filter and main oil gallery being drained or empty. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This preliminary information bulletin instructs to technicians to check the trigger wheel for interfering with the timing chain, and adding a shim to the camshaft position sensor. Read More »
This preliminary information bulletin instructs to technicians to check the trigger wheel for interfering with the timing chain, and adding a shim to the camshaft position sensor. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the Service Engine Soon (SES) lamp illuminated and/or Service Emission System ... Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp illuminated on Driver Information Center. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This Preliminary information communicates to the dealer technicians that a belt chirp or rubbing noise may be caused by the harmonic balancer out ring moving backward on the pulley and contacting the front cover. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards a start/stop event or during a normal start using the push button on the dash ... Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This technical bulletin provides repair information to correct a customer concern of Service Engine Soon Message at Start Up or Shortly after Start Up. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This Preliminary information communicates an issue with a noise caused by the engine harness rubbing on the floor pan. Dealers are to reposition the harness to fix the noise. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This informational bulletin provides information for dealers/technicians on Engine Control Module Calibration for T1 L3B Engine with DTC P26BB Set. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours. Read More »
Service Update - Certain vehicles equipped with a 2.7L turbo engine (RPO L3B), may have a condition where the engine wiring harness may have been wrapped and/or routed incorrectly, creating the potential for wear-through in several ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This engineering information (EI) is requesting information from the field on vehicles experiencing reduced engine power. GM Engineering needs to gather information to root cause the customer concern and develop a field fix. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
This preliminary information communicates the part restriction for the diesel turbocharger and EGR components. Updated to provide instruction on gathering additional data. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This preliminary information communicates the part restriction for the diesel turbocharger and EGR components. Updated to provide instruction on gathering additional data. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
Service Update - Certain vehicles may have a condition where the check engine or the reduced power mode light may come on during start-up or while driving. Reprogram the engine control module and the reductant control module. Read More »
This engineering information (EI) bulletin is requesting information from the field on vehicles experiencing reduced engine power. GM Engineering needs to gather information to root cause the customer concern and develop a field fix. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition. Read More »
This engineering informational bulletin is requesting information for checking for DTCs and the voltage (relative to a ground) on BOTH sides of the 400A starter fuse in the Battery Distribution Engine Compartment Fuse Block. Read More »
This engineering informational bulletin is requesting information from the field on no crank / no start issue resulting in a starter replacement due to the solenoid overheating. Read More »
This Preliminary information communicates to the technician to reprogram the engine control module and, if necessary, diagnose and repair P24B0. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
This engineering informational bulletin is requesting information on vehicles with the Service Engine Soon (SES) lamp being illuminated and DTC P1467 set. Read More »
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up on the glow plug causing a premature failure. Read More »
This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This Preliminary information communicates to dealers? information related to a Malfunction Indicator Lamp (MIL) Illuminated due to a U0672 setting. Advises the technician to perform Electric Engine Coolant Pump connection inspections. Read More »
This service bulletin provides a procedure to replace the valve lifter and guides to correct customer concerns of Poor Engine Performance, Engine Misfires, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0300, P0301, P0302, P0303, ... Read More »
This technical bulletin provides repair information to correct a customer concern of Evaporative DTCs P0442, P0446, P0455 or P0449, Caused by Dust Intrusion into the Evaporative Canister. Read More »
This service bulletin provides a repair procedure to correct customer concerns of Service Emissions System Displayed on DIC, MIL Illuminated with DTC P249C and/or P20E8 Set. Read More »
This Preliminary information communicates that some customers may comment that after an auto-stop event the engine does not restart and to inspect the engine ground strap. Temporarly on hold while PIE0572 is active. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This service bulletin provides a repair procedure to correct customer concerns of Service Emissions System Displayed on DIC, MIL Illuminated with DTC P249C and/or P20E8 Set. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This technical bulletin provides repair information to correct a customer concern of 2020 - 2022 Silverado and Sierra Equipped with Diesel Engine Setting DTCs P20BB or P20C3. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin provides repair information for Engine Wire Harness Chafing to correct customer concerns of IPC Gauges Sweep, IPC Warning Message, SES/Check Engine/MIL, No Start/ No Crank, Runs Rough, Stalls, Reduced Engine Power, ... Read More »
This service bulletin provides a procedure to program the glow plug control module to correct a customer concern of a Malfunction Indicator Lamp Illuminated with One or More Glow Plug Control DTCs Set. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides repair information to correct a customer concern of Evaporative DTCs P0442, P0446, P0455 or P0449, Caused by Dust Intrusion into the Evaporative Canister. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This informational bulletin provides information for dealers/technicians on Engine Control Module Calibration for T1 L3B Engine with DTC P26BB Set. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This technical bulletin provides repair information to correct a customer concern of Evaporative DTCs P0442, P0446, P0455 or P0449, Caused by Dust Intrusion into the Evaporative Canister. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin provides a procedure to replace the valve lifter and guides to correct customer concerns of Poor Engine Performance, Engine Misfires, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0300, P0301, P0302, P0303, ... Read More »
This service bulletin provides a procedure to replace the valve lifter and guides to correct customer concerns of Poor Engine Performance, Engine Misfires, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0300, P0301, P0302, P0303, ... Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up on the glow plug causing a premature failure. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This technical bulletin provides repair information to correct a customer concern of Charge Air Cooler (CAC) Icing, Check Engine Lamp Illuminated, Possible P0299, P2227, and/or P0300 DTCs Set. Read More »
This Preliminary information communicates to the dealers information related to a Malfunction Indicator Lamp (MIL) Illuminated During Cold Ambient Temperatures with DTCs P30C3 and/or P30BF P30C7 P30CB Setting. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This Preliminary information communicates to dealers? information related to a Malfunction Indicator Lamp (MIL) Illuminated due to a U0672 setting. Advises the technician to perform Electric Engine Coolant Pump connection inspections. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running ... Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to Service Engine Soon (SES) Lamp illuminated and/or a??Service Emissions Systema?? message on the Driver Information Center (DIC). Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Informational bulletin advises the technician of a possible oil leak at the front cover and how to diagnose it to verify if it is coming from the seal or not. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Service Engine Soon (SES) Lamp illuminated and/or a??Service Emissions Systema?? ... Read More »
This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This technical bulletin advises to replace the camshaft cover if found within the Julian date and the cause of a customer concern of possible oil consumption with or without DTC P06DD. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards Service Emission System and/or DEF Level Low message on driver information center (DIC). Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This technical bulletin provides repair information to correct a customer concern of 2020 - 2022 Silverado and Sierra Equipped with Diesel Engine Setting DTCs P20BB or P20C3. Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards Service Emission System and/or DEF Level Low message on driver information center ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Oil Leaking from Front of Engine. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This technical bulletin advises to replace the camshaft cover if found within the Julian date and the cause of a customer concern of possible oil consumption with or without DTC P06DD. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This Preliminary information communicates the possibility of a misfire or rough running concern and abnormal engine noise due to excessive wear in exhaust roller follower axle pin. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, Shake, Vibration, Harsh Shift, Delayed Shift and/or ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This Preliminary information communicates the possibility of dtc p06DD due to low or no oil pressure immediately following engine oil and filter change due to oil filter and main oil gallery being drained or empty. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This Preliminary information communicates to dealership technicians to perform a sweep of the coolant flow control valve and test the circuits before replacing the Engine Coolant Flow Control Valve, and to assist engineering in root ... Read More »
This Preliminary information communicates to technicians to replace the ECM and affected sensor if diagnostics leads to replacement of the ECM. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, ... Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine ... Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides a procedure to correct a condition of a Service Emission System and/or Service Engine Soon Lamp Illuminated on Driver Information Center (DIC), DTC P208B Set. Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This technical bulletin provides a procedure to correct the condition of Information on Vehicles Engine Shuts Off After 30 or 60 Minutes of Idling. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Customer Satisfaction Program. Certain vehicles, equipped with a gas engine, may have a condition in which the printed circuit board inside of the water pump may have been manufactured incorrectly potentially causing a water pump failure. Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This Preliminary information communicates an issue with the engine wiring harness shorting on the ecm mounting bracket and provides repair instructions. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a no restart after auto-stop event and/or, no crank. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards check to the engine lamp being illuminated on the drivers information center (DIC). Read More »
This preliminary information communicates the part restriction for the diesel turbocharger and EGR components. Updated to provide instruction on gathering additional data. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
This Preliminary information communicates that some customers may comment that after an auto-stop event the engine does not restart and to inspect the engine ground strap. Temporarly on hold while PIE0572 is active. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
This Preliminary information communicates an issue with the engine wiring harness shorting at the left front cylinder head causing any of the following issues: - IPC gauges sweeping while driving - Several IPC warning messages and ... Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This Preliminary information communicates The vehicle may have an SES lamp with any of the following DTC P06DA, P06DB, P06DC, P250A, P0300, P0340, P0341, P0335, P0336, P0641, P0011, P0010, P2088, P2089, and/or P2230. Read More »
This preliminary information communicates the part restriction for the diesel turbocharger and EGR components. Updated to provide instruction on gathering additional data. Read More »
This Preliminary information communicates an issue with the engine wiring harness shorting on the ecm mounting bracket and provides repair instructions. Read More »
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours. Read More »
This Preliminary information communicates the possibility of DTC P3075 being set current or history due to low coolant level or air trapped in cooling system. Read More »
This Preliminary information communicates to the technician to reprogram the engine control module and, if necessary, diagnose and repair P24B0. Read More »
This Preliminary information communicates that some customers may comment that after an auto-stop event the engine does not restart and to inspect the engine ground strap. Read More »
This Preliminary information communicates A vehicle may come into the dealer with a rough idle, lean running concern and/or air leak noise from the PCV system. Read More »
This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid ... Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
N192266751 - Service Update (9 VINs moved from N192266750 due to different procedure). On certain vehicles that are equipped with a 6.6L diesel engine, may have one or more of the following conditions exist: 1. Read More »
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
This Preliminary information communicates an issue with the engine wiring harness shorting at the left front cylinder head causing any of the following issues: - IPC gauges sweeping while driving - Several IPC warning messages and ... Read More »
This Preliminary information communicates A vehicle may have a tick noise from the engine cold, initial start in the morning. A lifter may not have sufficient amount of oil during cold start operation (not pumped up). Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. Read More »
The Preliminary Information communication advises the technician that the Product Quality Center has a part exchange for 3.0 LM2 engine. The dealer technician is advised to call the GM Product Quality Center for further assistance. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This informational bulletin advises the tech of a possible loose bolts at the turbo actuator and to replace turbo if the bolts have been found loose. Read More »
This preliminary information communicates the part restriction for the diesel turbocharger and EGR components. Updated to provide instruction on gathering additional data. Read More »
This technical bulletin provides repair information to correct a customer concern of 2020 - 2022 Silverado and Sierra Equipped with Diesel Engine Setting DTCs P20BB or P20C3. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
Service Update - In some vehicles, equipped with diesel engines, the Diesel Exhaust Fluid (DEF) system may not immediately reactivate, as it should, after the vehicle?s control system finds that a DEF heater fault is no longer present. Read More »
This New Engine Features Bulletin provides General Information to help the Service Personnel become familiar with the Duramax Diesel 3.0L - RPO LM2. Read More »
This preliminary information communicates the part restriction for the diesel turbocharger and EGR components. Updated to provide instruction on gathering additional data. Read More »
ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PIPES, HOSES, AND FITTINGS
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
Service Update. Certain vehicles may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18A?C (0A?F) or ... Read More »
This service bulletin provides a service procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3075 Set. Read More »
This service bulletin provides repair information for dealers/technicians to correct a customer concern of a Malfunction Indicator Lamp Illuminated with DTC P26BB Set. Read More »
Emission Recall. General Motors has decided to conduct a voluntary emissions recall involving certain vehicles equipped with a performance air intake system (LPO RVK or 5W7). Read More »
This service bulletin provides a repair procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3055 Set. Read More »
This Preliminary information communicates some diagnostic tips to inspect for no/low voltage at the ECM for a customers complaints of a SES MIL, Crank No Start, stalling DTC's: P16A7 and/or P16AF. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This service bulletin provides a service procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3075 Set. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine ... Read More »
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates in temperatures below freezing, it may be noticed that exhaust is only exiting from the right hand exhaust tailpipe. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Service Engine Soon (SES) Lamp illuminated and/or a??Service Emissions ... Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
Service Update - In some vehicles, equipped with diesel engines, the Diesel Exhaust Fluid (DEF) system may not immediately reactivate, as it should, after the vehicle?s control system finds that a DEF heater fault is no longer present. Read More »
This technical bulletin provides a procedure to program the ECM and/or replace the exhaust particulate sensor to correct the DTC that set after the service update has been previously performed. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the Service Engine Soon (SES) lamp illuminated and/or Service Emission System ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This Preliminary information communicates in temperatures below freezing, it may be noticed that exhaust is only exiting from the right hand exhaust tailpipe. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates to dealers? information related to a Malfunction Indicator Lamp (MIL) Illuminated due to a U0672 setting. Advises the technician to perform Electric Engine Coolant Pump connection inspections. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary information communicates information that the EVAP purge pump may be filling with liquid fuel if the customer overfills the fuel tank by over 3 clicks of a normal filler nozzle. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This Preliminary information communicates an issues with a SES MIL and DTC P1005 and to replace the fuel pump driver control module with an updated part number. Read More »
This Preliminary information communicates information that the EVAP purge pump may be filling with liquid fuel if the customer overfills the fuel tank by over 3 clicks of a normal filler nozzle. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This Preliminary information communicates information that the EVAP purge pump may be filling with liquid fuel if the customer overfills the fuel tank by over 3 clicks of a normal filler nozzle. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This bulletin advises the tech that there are extra characters on the fuel injector and to ignore the last numbers when identifying flow rate. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards Service Emission System and/or DEF Level Low message on driver information center ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
Service Update - In some vehicles, equipped with diesel engines, the Diesel Exhaust Fluid (DEF) system may not immediately reactivate, as it should, after the vehicle?s control system finds that a DEF heater fault is no longer present. Read More »
This preliminary information communicates the part restriction for the diesel turbocharger and EGR components. Updated to provide instruction on gathering additional data. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in performance in regards to the customers concerns. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This informational bulletin advises the tech of a possible normal condition when the vehicle creeps forward during start up conditions when the clutch packs are full of residual oil. Read More »
This Preliminary information communicates to have the dealer contact TAC with the transmission TUN number prior to transmission installation. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension housing and to perform testing on transmission for other possible issues, but it still may be possible on high ... Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This service bulletin provides repair information for Engine Wire Harness Chafing to correct customer concerns of IPC Gauges Sweep, IPC Warning Message, SES/Check Engine/MIL, No Start/ No Crank, Runs Rough, Stalls, Reduced Engine Power, ... Read More »
This Preliminary information communicates a diagnostic tip to inspect the main ground connection when diagnosing any lack of power steering assist issues with DTCs C1597 and/or C1599. Read More »
This service bulletin provides a procedure to replace the front wheel drive shaft to correct a customer concern of a Squeak/Chirp Noise from Front Axle in 2wd. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and repair of 8 Speed Transmissions Read More »
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing a??Da?? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This bulletin provides a procedure to correct a customer concern that while driving at low speeds, the rear wheels lock up, causing vehicle to come to a stop as if the brakes were applied or the vehicle was shifted into park. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Delayed and/or Harsh Engagement of Transmission Shift After Vehicle Sitting with Engine Off. Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension housing and to perform testing on transmission for possible other issues, but it still may be possible on high mile ... Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This information advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF causing the customers concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This informational bulletin advises the technician of possibly installing the incorrect 1-2-7-8-R clutch fluid passage seal and which seal should be used with measurements of the seal. Read More »
This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair. Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing a??Da?? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or ... Read More »
This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv. Read More »
This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This Preliminary information communicates A vehicle may have a concern of a vibration or drone around 40 MPH and 1200 RPM under a light load. Debris in the tranmission mount. Inspect the transmission mount for debris. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Service Engine Soon (SES) Lamp illuminated and/or a??Service Emissions ... Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing a??Da?? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or ... Read More »
This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried to shift the t-case from 4lo to Hi gears while driving. Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, Shake, Vibration, Harsh Shift, Delayed Shift and/or ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, ... Read More »
This Preliminary information communicates to the dealer technician that some customers may comment the rear wheels locked up at low speeds after a hot soak. Technicians may find DTC's P2724, P2727 or P2729 set. Read More »
This preliminary information bulletin instructs to technicians to check the trigger wheel for interfering with the timing chain, and adding a shim to the camshaft position sensor. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Service Engine Soon Lamp Illuminated on Driver Information Center (DIC), ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on a tick and/or ping type noise heard from the Propeller Shaft during ... Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This Preliminary information communicates to the dealer technician to replace the transmission valve body on 2019-2021 10 speed transmissions to correct DTCs P2812 and P2814 setting if Service Information does not lead to root case of ... Read More »
This Preliminary Information provides information to the technician about a additional diagnostic tip for a check engine lamp for DTC P3055 and P3056 and the start/Stop being inoperative. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on a tick and/or ping type noise heard from the Propeller Shaft during ... Read More »
This Preliminary information communicates to the dealer technician to replace the valve body on 8 speed transmissions setting DTC P0796 if no debris is found in the transmission fluid pan. Read More »
This Preliminary information communicates to the dealer technician to replace the valve body on the 8L90 transmission setting DTC P0796 if no debris is found in the transmission fluid pan. Read More »
This Preliminary information communicates to the dealer technician to replace the valve body on the 8L90 transmission setting DTC P0796 if no debris is found in the transmission fluid pan. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This technical bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the transmission. Read More »
This technical bulletin provides a repair procedure to correct a customer concern of Delayed and/or Harsh Engagement of Transmission Shift After Vehicle Sitting with Engine Off. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
Service Update. Certain vehicles may have a condition where the transmission enters a neutral state when the internal range sensor (IRS) fault is active. Dealers are to reprogram the transmission control module. Read More »
This Preliminary information communicates diagnostic tips on finding root cause of a hoot noise. If the technician confirms the hoot noise is only present while the torque converter clutch is applying the technician should advise the ... Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This Preliminary information communicates to the dealer technician that the 10L60, 10L80 and the 10L90 transmissions have been place on a part restriction. Read More »
This Preliminary information communicates A vehicle may have a concern of a vibration or drone around 40 MPH and 1200 RPM under a light load. Debris in the tranmission mount. Inspect the transmission mount for debris. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to 8 speed transmission shift quality. Read More »
Service Update - Certain vehicles may have a condition where the check engine or the reduced power mode light may come on during start up or while driving. Reprogram the engine control module and the reductant control module. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed. Read More »
This Preliminary information communicates to the dealer technician that the 10L60, 10L80 and the 10L90 transmissions have been place on a part restriction. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to 8 speed transmission shift quality. Read More »
This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates to the dealer technician diagnostic tips to aid in finding root case of P0708 setting on vehicles equipped with 8L45, 8L90, 10L60, 10L80 and 10L90 transmissions. Read More »
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed. Read More »
Customer Satisfaction Program - Certain 2019-2020 model year Chevrolet Silverado and GMC Sierra vehicles, equipped with an 8-Speed Automatic Transmission, may have a condition where the rear wheels will lock up at low speeds. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the transmission. Read More »
Customer Satisfaction Program - Certain vehicles, equipped with the 6-speed automatic transmission, may have a condition in which there is a slight deformation in the stator shaft. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This technical provides a procedure to locate, disconnect and re-connect the TCM electrical connector if found the cause of the customers concerns. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:VALVES/VALVE BODY
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:FILTER/SCREEN
This Preliminary information communication provides information to the technician on installing Regular Production Option Code 9L7 Up-fitter Auxiliary Switches. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:SEALS/GASKETS
This Informational bulletin advises the technician of a possible oil leak at the front cover and how to diagnose it to verify if it is coming from the seal or not. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp illuminated on Driver Information Center. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates that engineering is investigating a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates that engineering is investigating a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This Preliminary information communicates that some customers may comment that after an auto-stop event the engine does not restart and to inspect the engine ground strap. Temporarily on hold while PIE0572 is active. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides a repair procedure to correct customer concerns of Service Emissions System Displayed on DIC, MIL Illuminated with DTC P249C and/or P20E8 Set. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code 9L7 Up-fitter Auxiliary Switches. Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This technical bulletin provides repair information to correct a customer concern of 2020 - 2022 Silverado and Sierra Equipped with Diesel Engine Setting DTCs P20BB or P20C3. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This Preliminary information communicates diagnostic tips when trying to root cause a SES MIL with DTC's B2B0D and B2B0E. Main cause is aftermarket electrical devices spliced into the ignition main fuses. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This service bulletin provides repair information for Engine Wire Harness Chafing to correct customer concerns of IPC Gauges Sweep, IPC Warning Message, SES/Check Engine/MIL, No Start/ No Crank, Runs Rough, Stalls, Reduced Engine Power, ... Read More »
This service bulletin advises the technician of a possible loose ground that may be causing customer concerns of Loss of Steering Assist and/or Loss of Brake Assist and Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides a procedure to program the glow plug control module to correct a customer concern of a Malfunction Indicator Lamp Illuminated with One or More Glow Plug Control DTCs Set. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin provides information for dealers/technicians on Engine Control Module Calibration for T1 L3B Engine with DTC P26BB Set. Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This technical bulletin provides a procedure to replace the air bag and air bag harness to correct a condition of Airbag Malfunction Warning and Airbag Malfunction Indicator Illuminated with DTC B0001-1B due to corrosion. Read More »
This service bulletin provides repair information to correct a customer concern of Rear View Camera Issues - DTCs B395A, B395B, B395C, B101E, B101D. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This service bulletin provides information to dealership personnel that after performing a brake inspection, brake pad replacement, or any other repair that requires the caliper piston to be reseated may be causing DTC C05B0 to falsely ... Read More »
This service bulletin provides repair information on Radio Software Version U168 Update to correct customer concerns of radio software issues. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This technical bulletin provides repair information to correct a customer concern of Trailer Tire Pressure Only Reading Up To 100 PSI, New Parts To Increase To 147 PSI. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This service bulletin provides repair information to correct a customer concern of Rear View Camera Coaxial Related Issues - DTCs B395A, B395B, B395C, B101E, B101D. Read More »
This service bulletin provides repair information on Radio Software Version U168 Update to correct customer concerns of radio software issues. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Preliminary information communicates a diagnostic tip for an issue where the starter stays engaged after the engine starts. Dealers are to suspect/monitor the crankshaft position sensor. Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This technical bulletin provides repair information to correct a customer concern of Charge Air Cooler (CAC) Icing, Check Engine Lamp Illuminated, Possible P0299, P2227, and/or P0300 DTCs Set. Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This Preliminary information communicates diagnostic tips when trying to root cause a SES MIL with DTC's B2B0D and B2B0E. Main cause is aftermarket electrical devices spliced into the ignition main fuses. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This Preliminary information communicates to the dealers information related to a Malfunction Indicator Lamp (MIL) Illuminated During Cold Ambient Temperatures with DTCs P30C3 and/or P30BF P30C7 P30CB Setting. Read More »
This service bulletin provides diagnostic/repair information to correct a customer concern of Cellphone not Charging or USB Receptacle Inoperative. Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides repair information to correct a customer concern of Radio System Settings Lost or Returning to Default Values. Read More »
This technical bulletin provides a procedure to install 2 way tape to correct a condition of Trailering Connector Loose Within Rear Bumper. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer other wise found by a possible faulty trailer connector. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Service Engine Soon (SES) Lamp illuminated and/or a??Service Emissions ... Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Diagnostic Tips For Park Assist Off Message / Unwanted Or False Park Assist Alerts / No DTCs. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
This Preliminary information communicates to the dealers information related to a Malfunction Indicator Lamp (MIL) Illuminated During Cold Ambient Temperatures with DTCs P30C3 and/or P30BF P30C7 P30CB Setting. Read More »
This Engineering Information (EI) Closure ends the need for further information from the field regarding No Heat from Driver Side Inboard Dash Duct and/or Weak Heat On Driver Side. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Read More »
This Preliminary information communicates to the dealer technician that some customers may comment the rear wheels locked up at low speeds after a hot soak. Technicians may find DTC's P2724, P2727 or P2729 set. Read More »
This Preliminary information communicates a condition where the Video Processing Control Module is not able to be programmed to the vehicle. This PI offeres a couple workarounds while Engineering evaluates the concern. Read More »
This preliminary information bulletin instructs to technicians to check the trigger wheel for interfering with the timing chain, and adding a shim to the camshaft position sensor. Read More »
This Preliminary information communicates diagnostic tips when trying to root cause a SES MIL with DTC's B2B0D and B2B0E. Main cause is aftermarket electrical devices spliced into the ignition main fuses. Read More »
This Preliminary information communicates a condition where the Video Processing Control Module is not able to be programmed to the vehicle. This PI offeres a couple workarounds while Engineering evaluates the concern. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
Emission Recall. General Motors has decided to conduct a voluntary emissions recall involving certain vehicles equipped with a performance air intake system (LPO RVK or 5W7). Read More »
This service bulletin provides a repair procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3055 Set. Read More »
This Preliminary information communicates a condition where the Video Processing Control Module is not able to be programmed to the vehicle. This PI offeres a couple workarounds while Engineering evaluates the concern. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the Service Engine Soon (SES) lamp illuminated and/or Service Emission System ... Read More »
This technical bulletin provides a procedure to inspect fuses F51DR and/or F52DR in the X51R right instrument panel fuse block when they should not be installed. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This technical bulletin provides a procedure to inspect fuses F51DR and/or F52DR in the X51R right instrument panel fuse block when they should not be installed. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Loss of Power, Instrument Panel Cluster (IPC) Gauges are Inoperative and/or ... Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp illuminated on Driver Information Center. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This Preliminary information communicates and issue with the park assist off message or unwanted/false parking assist alerts and provide diagnostics tip for dealership to inspect the parking assist sensor/bezel mounting in the front and ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Malfunction Indicator Lamp illuminated on Driver Information Center (DIC) ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp illuminated on Driver Information Center. Read More »
This Preliminary information communicates information to not make any repairs for momentary camera flicker when brake light, turn signal, or hazards are active with radio RPO IOR. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Loss of Power, Instrument Panel Cluster (IPC) Gauges are Inoperative and/or ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a Dead Battery and/or Shift to Park Lamp Illuminated On Driver Information ... Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This service bulletin announces that the Part Restriction and Ordering Process Information for OnStar? Vehicle Communication Interface Modules (VCIM) (GMNA Only) has ended. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Loss of Power, Instrument Panel Cluster (IPC) Gauges are Inoperative and/or ... Read More »
This engineering information (EI is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to USB Port Does Not Charge or Recognize Phone/Device, or Not Holding Cable in Port, ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates a cocnern where a flashing spot can intermittently show up on the radio display while in reverse. The PI advises that engineering is investigating the concern. Read More »
This service bulletin provides information and a service procedure for dealers/technicians on OnStar Over the Air Update for TTY / TDD Operation and Continuous Improvement Changes. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates an issue with the underhood electrical center bolts being loose which can cause any of the following symptoms: - No crank - No start - Starter grinds or reengages after engine running - ... Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering released updated cals for the BSCM to repair the issue. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards a start/stop event or during a normal start using the push button on the dash ... Read More »
This Preliminary information communicates an issue with the engine wiring harness shorting on the ecm mounting bracket and provides repair instructions. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This engineering information (EI) revision ends the need for information from the field regarding Check Trailer Message on Drivers Information Center (DIC) and/or F74, F82 Fuses Blown. Read More »
This Preliminary information communicates an XM service concern of no audio at startup until a channel change and directs to contact XM for direct support. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Malfunction Indicator Lamp (MIL) Illuminated and/or functional failures of ... Read More »
This informational bulletin provides information for dealers/technicians on Engine Control Module Calibration for T1 L3B Engine with DTC P26BB Set. Read More »
This Preliminary information communicates multiple vehicle issues caused by an aftermarket device and it gives dealership information where to inspect for this device. Read More »
This Preliminary information communicates to dealership how to test properly trailer light option on the truck and also provide additional information on trailer issues. Read More »
This technical provides a procedure to locate, disconnect and re-connect the TCM electrical connector if found the cause of the customers concerns. Read More »
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw. Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering released updated cals for the BSCM to repair the issue. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Shift to Park Message on Drivers Information Center (DIC) (ONLY On Push Button ... Read More »
Customer Satisfaction Program - Certain 2019-2020 model year Chevrolet Silverado and GMC Sierra vehicles, equipped with an 8-Speed Automatic Transmission, may have a condition where the rear wheels will lock up at low speeds. Read More »
This engineering information (EI) is requesting information from technicians to perform the checklist provided and contact the engineer listed in regards to Shift to Park Message on Drivers Information Center (DIC) (ONLY On Push Button ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Shift to Park Message on Drivers Information Center (DIC) (ONLY On Push Button ... Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Malfunction Indicator Lamp (MIL) Illuminated and/or functional failures of ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to SD Code messages displayed on the Radio Screen and/or Instrument Cluster - ... Read More »
This Preliminary information communicates diagnostic tips when trying to root cause a SES MIL with DTC's B2B0D and B2B0E. Main cause is aftermarket electrical devices spliced into the ignition main fuses. Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This Technical bulletin provides service procedure information for dealers/technicians on Radio Software Version V135116 Over-the-Air Update. Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering released updated cals for the BSCM to repair the issue. Read More »
This technical bulletin provides repair information to correct a customer concern of Loss of Brake Assist, Various Messages Displayed in DIC, Brake Pedal Travel and Apply May Feel Different, DTC C0024 Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Blue Screen and Service Rear Vision System Message on Radio Display. Read More »
This engineering information (EI) is requesting information from the field on conditions of Service Engine Soon (SES) Lamp Illuminated, DTCs B2B0D and/or B2B0E Central Gateway Module Codes Unable to Communicate with HSLAN or LSLAN. Read More »
This technical bulletin provides repair information to correct a customer concern of the pickup box power endgate may not open on initial press, or may not open at all. Read More »
This Preliminary information communicates to the dealer that a customer may comment that the MIL light is illuminated. The technician may find P1098 and/or P26BB set current or history. Read More »
This informational bulletin provides information for dealers/technicians on Accessory Rear Seat Infotainment (RSI) Shuts Off, Coinciding with Closing of Door or Liftgate. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering is working on updated cals for the BSCM. Read More »
This Preliminary information communicates repair information on Service Brake System, Reduced Engine Power, and Speed Limited messages on the DIC. Along with these messages, a SES MIL will be on and the brake pedal may feel hard. Read More »
Service Update - Certain vehicles may have a condition where the check engine or the reduced power mode light may come on during start-up or while driving. Reprogram the engine control module and the reductant control module. Read More »
This engineering information (EI) is requesting information from the field to perform the check list provided and contact the engineer in regards to Instrument Panel Cluster (IPC) Gages at Zero, Multiple Warning Lights On, No Chimes ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Lane Keep Assist inoperative with the lane keep assist switch LED is always on and the lane keep assist Icon is not illuminated on ... Read More »
This Preliminary information communicates an issues with a SES MIL and DTC P1005 and to replace the fuel pump driver control module with an updated part number. Read More »
This Preliminary information communicates to the technician to reprogram the engine control module and, if necessary, diagnose and repair P24B0. Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This engineering informational bulletin is requesting information for checking for DTCs and the voltage (relative to a ground) on BOTH sides of the 400A starter fuse in the Battery Distribution Engine Compartment Fuse Block. Read More »
This engineering informational bulletin is requesting information from the field on no crank / no start issue resulting in a starter replacement due to the solenoid overheating. Read More »
This Preliminary information communicates to the dealer that a customer may comment that the MIL light is illuminated. The technician may find P1098 and/or P26BB set current or history. Read More »
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Read More »
This bulletin provides information regarding Part Restriction and Ordering Process Information for OnStar? Vehicle Communication Interface Modules (VCIM) (GMNA Only). Read More »
This Preliminary information communicates to the technician to reprogram the engine control module and, if necessary, diagnose and repair P24B0. Read More »
Customer Satisfaction Program - certain vehicles may have a condition in which both front seats cooling ventilation feature is inoperative. The cooling switch will not activate the seat fans. Read More »
This Preliminary information communicates repair information on Service Brake System, Reduced Engine Power, and Speed Limited messages on the DIC. Along with these messages, a SES MIL will be on and the brake pedal may feel hard. Read More »
Service Update - Certain vehicles may have a condition where the check engine or the reduced power mode light may come on during start up or while driving. Reprogram the engine control module and the reductant control module. Read More »
This Preliminary information communicates to the technician to reprogram the engine control module and, if necessary, diagnose and repair P24B0. Read More »
This engineering information bulletin is requesting information from the field on no crank / no start issue resulting in a starter replacement due to the solenoid overheating. Read More »
N192279350 - Service Update Bulletin. On certain vehicles, dealer installed accessory LED fog lamps were offered and sold to customers, but there was not a body control module calibration available at the time to enable the fog lamps to ... Read More »
This engineering information (EI) bulletin is requesting information from the field on conditions of Service Engine Soon (SES) Lamp Illuminated, DTCs B2B0D and/or B2B0E Central Gateway Module Codes Unable to Communicate with HSLAN or LSLAN. Read More »
This engineering informational bulletin is requesting information a issue that is caused by wire damage or an incorrect wire routing issue that results in a repair. Read More »
This engineering informational bulletin is requesting information on vehicles with the Service Engine Soon (SES) lamp being illuminated and DTC P1467 set. Read More »
This engineering informational bulletin is requesting information for checking for DTCs and the voltage (relative to a ground) on BOTH sides of the 400A starter fuse in the Battery Distribution Engine Compartment Fuse Block. Read More »
This Preliminary Information provides information to the technician about a additional diagnostic tip for a check engine lamp for DTC p3055 and P3056 and the start/Stop being inoperative. Read More »
This technical provides a procedure to locate, disconnect and re-connect the TCM electrical connector if found the cause of the customers concerns. Read More »
This Preliminary information communicates the potential for DTCs P2C7A and/or P14D9 to set, the current procedure to clear them and that an ECM calibration is being developed. Read More »
This Preliminary information communicates to the dealer that a customer may comment that the MIL light is illuminated. The technician may find P1098 and/or P26BB set current or history. Read More »
This Preliminary information communicates advises the technician that the ECM part number will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This technical bulletin provides repair information to correct a customer concern of Intermittent or Continuous Horn Blowing, Horn Activation Sensitive to the Touch. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
Service Update - Certain vehicles equipped with a 2.7L turbo engine (RPO L3B), may have a condition where the engine wiring harness may have been wrapped and/or routed incorrectly, creating the potential for wear-through in several ... Read More »
ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL
This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup ... Read More »
This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup ... Read More »
ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Service Engine Soon Lamp Illuminated on Driver Information Center (DIC), ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the Service Engine Soon (SES) lamp illuminated and/or Service Emission System ... Read More »
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
N192266751 - Service Update (9 VINs moved from N192266750 due to different procedure). On certain vehicles that are equipped with a 6.6L diesel engine, may have one or more of the following conditions exist: 1. Read More »
This Preliminary information communicates a Radio software update resolution for OnStar LED Red And Wifi Hotspot Inoperative After Remote Vehicle Start concern. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides repair information for dealers/technicians to correct a customer concern of a Malfunction Indicator Lamp Illuminated with DTC P26BB Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Crooked Rear View Camera Guideline Image on Radio Display. Read More »
This technical bulletin provides programming information for Radio Software Version U150 Update to correct software issues on infotainment systems IOS, IOT or IOU. Read More »
This technical bulletin provides programming information for Radio Software Version U150 Update to correct software issues on infotainment systems IOS, IOT or IOU. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This technical bulletin provides programming information for Radio Software Version U150 Update to correct software issues on infotainment systems IOS, IOT or IOU. Read More »
This Preliminary information communicates a condition where the trailering app cannot be opened and provides a process for clearing the cache and personal data so the application will operate as designed. Read More »
This technical bulletin provides repair information to correct a customer concern of Service Engine Soon Message at Start Up or Shortly after Start Up. Read More »
This Technical bulletin provides service procedure information for dealers/technicians on Radio Software Version V135116 Over-the-Air Update. Read More »
This Technical bulletin provides a service procedure for dealers/technicians on installation of Radio Software Version U148 Over-the-Air Update. Read More »
This Technical bulletin provides service procedure information for dealers/technicians on Radio Software Version V135116 Over-the-Air Update. Read More »
This Preliminary information communicates A vehicle with a customer concern of a SES P0128, Engineering is aware of the concern and working on the a repair. At this time clear the codes and do not replace the thermostat for this concern. Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This Preliminary information communicates and issue with the park assist off message or unwanted/false parking assist alerts and provide diagnostics tip for dealership to inspect the parking assist sensor/bezel mounting in the front and ... Read More »
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors. Read More »
This Preliminary information communicates to the dealers information related to a Malfunction Indicator Lamp (MIL) Illuminated During Cold Ambient Temperatures with DTCs P30C3 and/or P30BF P30C7 P30CB Setting. Read More »
This Preliminary information communicates to dealers? information related to a Malfunction Indicator Lamp (MIL) Illuminated due to a U0672 setting. Advises the technician to perform Electric Engine Coolant Pump connection inspections. Read More »
This Preliminary information provides information to the technician on installing a roof beacon light. Technician will need to reference the latest version of General Motors Up-fitter Integration Bulletin 157. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This Preliminary information communicates to the dealers information related to a Malfunction Indicator Lamp (MIL) Illuminated During Cold Ambient Temperatures with DTCs P30C3 and/or P30BF P30C7 P30CB Setting. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This Preliminary information communicates to the dealers information related to a Malfunction Indicator Lamp (MIL) Illuminated During Cold Ambient Temperatures with DTCs P30C3 and/or P30BF P30C7 P30CB Setting. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This service bulletin provides a service procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3075 Set. Read More »
This service bulletin provides repair information for dealers/technicians to correct a customer concern of a Malfunction Indicator Lamp Illuminated with DTC P26BB Set. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Malfunction Indicator Lamp illuminated on Driver Information Center (DIC) ... Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
N192279350 - Service Update Bulletin. On certain vehicles, dealer installed accessory LED fog lamps were offered and sold to customers, but there was not a body control module calibration available at the time to enable the fog lamps to ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on a turn signal not canceling and/or mis-canceling. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on a turn signal not canceling and/or mis-canceling. Read More »
This informational bulletin provides information on Outside Rear View Mirror Defog or Defrost Times Different for Passenger and Driver Mirrors. Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This technical bulletin provides repair information to correct a customer concern of DTC P0101 Mass Air Flow (MAF) Sensor Performance, P1682 Set after MAF Replacement. Read More »
This technical bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to gathering information for the power outside folding mirror with the ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to gathering information for the power outside folding mirror with the ... Read More »
This technical bulletin provides repair information to correct a customer concern of the foam strip between the I/P trim and base of the windshield detaching from the upper I/P trim panel. Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise coming from the window regulator area. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise coming from the window regulator area. Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
In certain vehicles, equipped with a manual HVAC system (RPO: C4P), the K33 HVAC Control Module may not properly enable the heater auxiliary coolant pump to maintain cabin heater temperature during engine auto stop events. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This technical bulletin provides a procedure to replace the air bag and air bag harness to correct a condition of Airbag Malfunction Warning and Airbag Malfunction Indicator Illuminated with DTC B0001-1B due to corrosion. Read More »
This Preliminary information communicates A vehicle may have a concern of a vibration or drone around 40 MPH and 1200 RPM under a light load. Debris in the tranmission mount. Inspect the transmission mount for debris. Read More »
This Preliminary information communicates to dealership how to test properly trailer light option on the truck and also provide additional information on trailer issues. Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the Service 4WD message displayed on the driver information center (DIC). Read More »
This technical bulletin provides a procedure to replace the air bag and air bag harness to correct a condition of Airbag Malfunction Warning and Airbag Malfunction Indicator Illuminated with DTC B0001-1B due to corrosion. Read More »
This technical bulletin provides repair information to correct a customer concern of hearing a rattle noise from driver or passenger seat belt. Read More »
This technical bulletin provides a procedure to replace the air bag and air bag harness to correct a condition of Airbag Malfunction Warning and Airbag Malfunction Indicator Illuminated with DTC B0001-1B due to corrosion. Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
This Preliminary information communicates to the dealer that a customer may comment that the MIL light is illuminated. The technician may find P1098 and/or P26BB set current or history. Read More »
Service Update - Certain vehicles may have a condition where the check engine or the reduced power mode light may come on during start up or while driving. Reprogram the engine control module and the reductant control module. Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
This technical bulletin provides repair information to correct a customer concern of hearing a rattle noise from driver or passenger seat belt. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This technical bulletin provides repair information to correct a customer concern of vertical misalignment between cab and pickup box on driver side of vehicle. Read More »
This engineering information (EI) closure ends the need to gather further information from technicians regarding taking pictures of decals wrinkling, peeling, bubbling, discoloration, delaminating and/or coming off. Read More »
This Preliminary information communicates an issue that when an engine mount is replaced there may be additional parts replaced along with the engine mount and dealership are to reference the parts catalog to determine if additional parts ... Read More »
This technical bulletin provides repair information to correct a customer concern of the foam strip between the I/P trim and base of the windshield detaching from the upper I/P trim panel. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This technical bulletin provides repair information to correct a customer concern of the foam strip between the I/P trim and base of the windshield detaching from the upper I/P trim panel. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This Preliminary information communicates A vehicle may have a concern of a vibration or drone around 40 MPH and 1200 RPM under a light load. Debris in the tranmission mount. Inspect the transmission mount for debris. Read More »
This engineering informational bulletin is requesting information from technicians to take pictures of decals wrinkling, peeling, bubbling, discoloration, delaminating and/or coming off and contact the engineer listed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This technical bulletin provides repair information to correct a customer concern of vertical misalignment between cab and pickup box on driver side of vehicle. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin provides repair information to correct a customer concern of Diagnostic Tips For Park Assist Off Message / Unwanted Or False Park Assist Alerts / No DTCs. Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This service bulletin provides a procedure to replace both front door seals to correct a customer concern of Howl, Hoot, or Whistle Type Noise when Driving in Crosswinds. Read More »
This service bulletin provides a procedure to replace both front door seals to correct a customer concern of Howl, Hoot, or Whistle Type Noise when Driving in Crosswinds. Read More »
This Preliminary information communicates to the dealer technician to replace the transmission valve body on 2019-2021 10 speed transmissions to correct DTCs P2812 and P2814 setting if Service Information does not lead to root case of ... Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This Preliminary information communicates to the dealer technician to replace the valve body on 8 speed transmissions setting DTC P0796 if no debris is found in the transmission fluid pan. Read More »
This Preliminary information communicates to the dealer technician to inspect for a missing 1-2-7-8-R clutch fluid passage seal or incorrect 1-2-7-8-R clutch fluid passage seal being install for a no movement concern after valve body ... Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This technical bulletin provides repair information to correct a customer concern of vertical misalignment between cab and pickup box on driver side of vehicle. Read More »
This Preliminary information communicates to the dealer technician to replace the valve body on the 8L90 transmission setting DTC P0796 if no debris is found in the transmission fluid pan. Read More »
This Preliminary information communicates to the dealer technician to replace the valve body on the 8L90 transmission setting DTC P0796 if no debris is found in the transmission fluid pan. Read More »
This technical bulletin provides repair information to correct a customer concern of vertical misalignment between cab and pickup box on driver side of vehicle. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This technical bulletin provides repair information to correct a customer concern of the Tri-Fold Tonneau paint finish fading or discolored. Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This Preliminary information communicates A vehicle may have a concern of a vibration or drone around 40 MPH and 1200 RPM under a light load. Debris in the tranmission mount. Inspect the transmission mount for debris. Read More »
Customer Satisfaction Program - certain vehicles may have a condition in which both front seats cooling ventilation feature is inoperative. The cooling switch will not activate the seat fans. Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This Preliminary information communicates advises the technician that the ECM part number will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
N192279350 - Service Update Bulletin. On certain vehicles, dealer installed accessory LED fog lamps were offered and sold to customers, but there was not a body control module calibration available at the time to enable the fog lamps to ... Read More »
This technical bulletin provides repair information to correct a customer concern of vertical misalignment between cab and pickup box on driver side of vehicle. Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This engineering informational bulletin is requesting information from technicians to take pictures of decals wrinkling, peeling, bubbling, discoloration, delaminating and/or coming off and contact the engineer listed. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This technical bulletin provides repair information to correct a customer concern of vertical misalignment between cab and pickup box on driver side of vehicle. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This technical bulletin provides repair information to correct a customer concern of Hard Tri-Fold tonneau water leaks at the front corners of the pickup box. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides a procedure to replace both front door seals to correct a customer concern of Howl, Hoot, or Whistle Type Noise when Driving in Crosswinds. Read More »
This Preliminary information communicates an issue with the rear door lock rod sticking in the door panel bezel and provides direction on repairing the issue. Read More »
This Preliminary information communicates an issue with the tailgate latch handle disengaging from the tailgate. Dealers are to remove the tailgate handle standoff brackets. Read More »
This technical bulletin provides repair information to correct a customer concern of the pickup box endgate will not fully close by itself. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a concern with the Rear View Camera not aligned (verbatims such as ... Read More »
This technical bulletin provides repair information to correct a customer concern of a pop noise heard coming from the rear roof of cab area. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a concern with the Rear View Camera not aligned (verbatims such as ... Read More »
This Preliminary information communicates an issue with the rear door lock rod sticking in the door panel bezel and provides direction on repairing the issue. Read More »
This Preliminary information communicates an issue with the tailgate latch handle disengaging from the tailgate. Dealers are to remove the tailgate handle standoff brackets. Read More »
This technical bulletin provides repair information to correct a customer concern of the pickup box power endgate may not open on initial press, or may not open at all. Read More »
This technical bulletin provides repair information to correct a customer concern of the pickup box power endgate may not open on initial press, or may not open at all. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ? of the way. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This Preliminary information communicates an issue of the wrong part number WSS being installed during a service procedure and to warn dealership tech to make sure the correct part number WSS is installed. Read More »
This bulletin provides a procedure to correct a customer concern that while driving at low speeds, the rear wheels lock up, causing vehicle to come to a stop as if the brakes were applied or the vehicle was shifted into park. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This technical bulletin provides repair information to correct a customer concern of Trailer Tire Pressure Only Reading Up To 100 PSI, New Parts To Increase To 147 PSI. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing ?D? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or 8-6 ... Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary information communicates to the dealer technician that some customers may comment the rear wheels locked up at low speeds after a hot soak. Technicians may find DTC's P2724, P2727 or P2729 set. Read More »
Customer Satisfaction Program - Certain 2019-2020 model year Chevrolet Silverado and GMC Sierra vehicles, equipped with an 8-Speed Automatic Transmission, may have a condition where the rear wheels will lock up at low speeds. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Preliminary information communicates to the dealer technician that some customers may comment the rear wheels locked up at low speeds after a hot soak. Technicians may find DTC's P2724, P2727 or P2729 set. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary information communicates to the dealer technician that some customers may comment the rear wheels locked up at low speeds after a hot soak. Technicians may find DTC's P2724, P2727 or P2729 set. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary information communicates to dealership how to test properly trailer light option on the truck and also provide additional information on trailer issues. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This engineering information (EI) is requesting information from technicians to perform the checklist provided and contact the engineer listed in regards to a Check Trailer Message on Drivers Information Center (DIC) and/or F74, F82 Fuses ... Read More »
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw. Read More »
Customer Satisfaction Program - certain vehicles may have a condition in which both front seats cooling ventilation feature is inoperative. The cooling switch will not activate the seat fans. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering released updated cals for the BSCM to repair the issue. Read More »
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Read More »
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Read More »
This Preliminary information communicates that after installation of GM Accessory Performance Brake Pads it may be noticed the EBCM has set DTC(s) C116C 05 and/or C116B 05. Read More »
This Preliminary information communicates an issue with the engine wiring harness shorting at the left front cylinder head causing any of the following issues: - IPC gauges sweeping while driving - Several IPC warning messages and ... Read More »
This Preliminary information communicates an issue with the engine wiring harness shorting at the left front cylinder head causing any of the following issues: - IPC gauges sweeping while driving - Several IPC warning messages and ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Lane Keep Assist inoperative with the lane keep assist switch LED is always on and the lane keep assist Icon is not illuminated on ... Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Lane Keep Assist inoperative with the lane keep assist switch LED is always on and the lane keep assist Icon is not illuminated on ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary information communicates information to the technician that if they receive a vehicle with this concern and verifying the rear view camera is zoomed in, General Motors is aware of this and have created a repair. Read More »
This Preliminary information communicates information to the technician that if they receive a vehicle with this concern and verifying the rear view camera is zoomed in, General Motors is aware of this and have created a repair. Read More »
This service bulletin provides repair information to correct a customer concern of Rear View Camera Coaxial Related Issues - DTCs B395A, B395B, B395C, B101E, B101D. Read More »
This Preliminary information communicates information to the technician that if they receive a vehicle with this concern and verifying the rear view camera is zoomed in, General Motors is aware of this and working on a solution for the ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary information communicates and issue when driving at highway speeds (above 60 mph) that there is a noise from the rear seat area that could be described as a buffering, pulsing, vibrating, roaring, booming type noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak and/or clunking noise coming from the rear of the vehicle. Read More »
This technical bulletin provides repair information to correct a customer concern of Crooked Rear View Camera Guideline Image on Radio Display. Read More »
This Preliminary information communicates an issue with a noise caused by the engine harness rubbing on the floor pan. Dealers are to reposition the harness to fix the noise. Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak and/or clunking noise coming from the rear of the vehicle. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This Preliminary information communicates that engineering is investigating a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates an issue with a noise caused by the engine harness rubbing on the floor pan. Dealers are to reposition the harness to fix the noise. Read More »
This Preliminary information communicates that after installation of GM Accessory Performance Brake Pads it may be noticed the EBCM has set DTC(s) C116C 05 and/or C116B 05. Read More »
This technical bulletin provides repair information to correct a customer concern of hearing a rattle noise from driver or passenger seat belt. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a concern with the Rear View Camera not aligned (verbatims such as ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a concern with the Rear View Camera not aligned (verbatims such as rear/back up ... Read More »
This Preliminary information communicates information on how to disable the Side Blind Zone Detection and Park Assist systems when a customer removes the pickup box from the vehicle to install an aftermarket bed or body. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
Customer Service Program - Certain vehicles may not have the backup alarm which should have been included the dealer kit. Dealers are to provide the missing backup alarm to the customer. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Read More »
This service bulletin provides repair information to correct a customer concern of Rear View Camera Issues - DTCs B395A, B395B, B395C, B101E, B101D. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Camera Display. Read More »
This Preliminary information communicates a cocnern where a flashing spot can intermittently show up on the radio display while in reverse. The PI advises that engineering is investigating the concern. Read More »
This Preliminary information communicates an engineering investigation for OnStar LED Red And Wifi Hotspot Inoperative After Remote Vehicle Start concern. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides a procedure to replace the front wheel drive shaft to correct a customer concern of a Squeak/Chirp Noise from Front Axle in 2wd. Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Preliminary information communicates an issue of the wrong part number WSS being installed during a service procedure and to warn dealership tech to make sure the correct part number WSS is installed. Read More »
This informational bulletin provides information on Outside Rear View Mirror Defog or Defrost Times Different for Passenger and Driver Mirrors. Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This engineering information (EI) closure ends the need to gather further information from technicians regarding taking pictures of decals wrinkling, peeling, bubbling, discoloration, delaminating and/or coming off. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This service bulletin provides repair information to correct a customer concern of Rear View Camera Issues - DTCs B395A, B395B, B395C, B101E, B101D. Read More »
This technical bulletin provides repair information to correct a customer concern of the foam strip between the I/P trim and base of the windshield detaching from the upper I/P trim panel. Read More »
This Preliminary information communicates the possibility of the Intake Cam Actuator cover plate screws backing out and making unwanted contact with the Cam Carrier. Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This service bulletin provides repair information on Radio Software Version U168 Update to correct customer concerns of radio software issues. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This technical bulletin provides repair information to correct a customer concern of Trailer Tire Pressure Only Reading Up To 100 PSI, New Parts To Increase To 147 PSI. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This service bulletin provides repair information to correct a customer concern of Rear View Camera Coaxial Related Issues - DTCs B395A, B395B, B395C, B101E, B101D. Read More »
This service bulletin provides repair information on Radio Software Version U168 Update to correct customer concerns of radio software issues. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This technical bulletin provides repair information to correct a customer concern of the Tri-Fold Tonneau paint finish fading or discolored. Read More »
This informational bulletin provides information for dealers/technicians on Information on GM Accessories - Instructions on Claim Submission on Dealer-Replaced Tonneau Covers During Warranty Period. Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Camera Display. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides diagnostic/repair information to correct a customer concern of Cellphone not Charging or USB Receptacle Inoperative. Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This Preliminary information communicates an issue of the wrong part number WSS being installed during a service procedure and to warn dealership tech to make sure the correct part number WSS is installed. Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides repair information to correct a customer concern of Radio System Settings Lost or Returning to Default Values. Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This technical bulletin provides repair information to correct a customer concern of Black Radio Display Screen and No Communication with the Video Processing Module (VPM). Read More »
This engineering informational bulletin is requesting information from technicians to take pictures of decals wrinkling, peeling, bubbling, discoloration, delaminating and/or coming off and contact the engineer listed. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This service bulletin provides repair information to correct a customer concern of Radio System Settings Lost or Returning to Default Values. Read More »
This service bulletin provides radio software version 135120 (IOR) update procedures to correct customer concerns of software related issues. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code 9L7 Up-fitter Auxiliary Switches. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This service bulletin provides a service procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3075 Set. Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary information communicates multiple vehicle issues caused by an aftermarket device and it gives dealership information where to inspect for this device. Read More »
This Preliminary information communicates a condition where the Video Processing Control Module is not able to be programmed to the vehicle. This PI offeres a couple workarounds while Engineering evaluates the concern. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a rubbing type noise heard while turning the steering wheel. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Service Engine Soon Lamp Illuminated on Driver Information Center (DIC), ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp illuminated on Driver Information Center. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the Service Engine Soon (SES) lamp illuminated and/or Service Emission System ... Read More »
Customer Satisfaction Program - Certain 2020 model year Chevrolet Silverado 1500 and Sierra 1500 vehicles are equipped with trailering information labels that incorrectly state the vehicle?s trailering capabilities. Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This informational bulletin provides information for dealers/technicians on Information on GM Accessories - Instructions on Claim Submission on Dealer-Replaced Tonneau Covers During Warranty Period. Read More »
This informational bulletin provides information for dealers/technicians on Information on GM Accessories - Instructions on Claim Submission on Dealer-Replaced Tonneau Covers During Warranty Period. Read More »
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition. Read More »
This Preliminary information communicates to the dealer technicians that a belt chirp or rubbing noise may be caused by the harmonic balancer out ring moving backward on the pulley and contacting the front cover. Read More »
Customer Satisfaction - Certain 2020 model year Chevrolet Silverado 1500 and Sierra 1500 vehicles are equipped with trailering information labels that incorrectly state the vehicle?s trailering capabilities. Install the overlay labels. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary information communicates to the dealer technician that the valve body Part Unique Number (PUN) may contain the letter O or the number 0. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to USB Port Does Not Charge or Recognize Phone/Device, or Not Holding Cable ... Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This technical bulletin provides repair information to correct a customer concern of a pop noise heard coming from the rear roof of cab area. Read More »
This informational bulletin advises the tech of a possible normal condition when the vehicle creeps forward during start up conditions when the clutch packs are full of residual oil. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Loss of Power, Instrument Panel Cluster (IPC) Gauges are Inoperative and/or ... Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This engineering information (EI is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to USB Port Does Not Charge or Recognize Phone/Device, or Not Holding Cable in Port, ... Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or Non-Responsive to Touch After Cleaning/Disinfecting Radio Display. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This technical bulletin provides programming information for Radio Software Version U150 Update to correct software issues on infotainment systems IOS, IOT or IOU. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
Customer Satisfaction Program. Certain vehicles, equipped with a gas engine, may have a condition in which the printed circuit board inside of the water pump may have been manufactured incorrectly potentially causing a water pump failure. Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a concern with the Rear View Camera not aligned (verbatims such as ... Read More »
This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise coming from the window regulator area. Read More »
This Preliminary information communicates a condition where the trailering app cannot be opened and provides a process for clearing the cache and personal data so the application will operate as designed. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This Preliminary information communicates an XM service concern of no audio at startup until a channel change and directs to contact XM for direct support. Read More »
This Preliminary information communicates information on radio software anamolies and future radio software updates to correct the concern. Read More »
Customer Satisfaction Program. Certain vehicles may have been double charged for the Off-Road Assist Steps at the time of purchase. Dealers will provide the customer with a reimbursement check in the amount of $965. Read More »
This technical bulletin provides repair information to correct a customer concern of Hard Tri-Fold tonneau water leaks at the front corners of the pickup box. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
Customer Satisfaction Program. As part of equipment recall N192285070, GM instructed dealers to remove recalled tri-fold tonneau covers on certain vehicles prior to delivery to the customer. Read More »
This Preliminary information communicates an issue with a noise caused by the engine harness rubbing on the floor pan. Dealers are to reposition the harness to fix the noise. Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates an issue with a SES MIL and the Brake System Control Module setting false DTC's during shut down. GM Engineering released updated cals for the BSCM to repair the issue. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This engineering information (EI) ends the needs for information from the field regarding SD Code messages displayed on the Radio Screen and/or Instrument Cluster - Navigation System Malfunction. Read More »
Customer Satisfaction Program. As part of equipment recall N192285070, GM instructed dealers to remove recalled tri-fold tonneau covers on certain vehicles prior to delivery to the customer. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a on a no restart after auto-stop event and/or, no crank. Read More »
This Preliminary information communicates that after installation of GM Accessory Performance Brake Pads it may be noticed the EBCM has set DTC(s) C116C 05 and/or C116B 05. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
This Preliminary information communicates multiple vehicle issues caused by an aftermarket device and it gives dealership information where to inspect for this device. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the conditions that are listed in this PIE. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Technical bulletin provides a service procedure for dealers/technicians on installation of Radio Software Version U148 Over-the-Air Update. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to SD Code messages displayed on the Radio Screen and/or Instrument Cluster - ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Technical bulletin provides service procedure information for dealers/technicians on Radio Software Version V135116 Over-the-Air Update. Read More »
This technical bulletin provides repair information to correct a customer concern of hearing a rattle noise from driver or passenger seat belt. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This technical bulletin provides repair information to correct a customer concern of endgate will not auto open or auto close after accessory tonneau cover installation, and/or poor fit of tonneau cover to endgate. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a vibration and/or banging noise heard from under the vehicle. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary information communicates to the dealer technician that the 10L60, 10L80 and the 10L90 transmissions have been place on a part restriction. Read More »
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to 8 speed transmission shift quality. Read More »
This bulletin provides information regarding Part Restriction and Ordering Process Information for OnStar? Vehicle Communication Interface Modules (VCIM) (GMNA Only). Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This Technical bulletin provides a service procedure for dealers/technicians on installation of Radio Software Version U148 Over-the-Air Update. Read More »
This Preliminary information communicates to the dealer technician to instruct the customer to use the block heater only at temperatures 0F and below. A calibration will become available at a later date. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary information communicates to dealership how to test properly trailer light option on the truck and also provide additional information on trailer issues. Read More »
This service bulletin advises the technician of a possible loose ground that may be causing customer concerns of Loss of Steering Assist and/or Loss of Brake Assist and Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This Preliminary information communication provides information to the technician on installing Regular Production Option Code 9L7 Up-fitter Auxiliary Switches. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This technical bulletin provides repair information to correct a customer concern of seeing the trailer running lights shut off due to excessive load on the running lamp circuit. Read More »
This Preliminary information communicates multiple vehicle issues caused by an aftermarket device and it gives dealership information where to inspect for this device. Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This Preliminary Information communication advises the technician that the Radio or Tuner, radio controls, Integrated Center Stack, HUD's, IPC's, and radio displays are placed on restriction through the General Motors Technical Assistance ... Read More »
This informational bulletin provides information on Loss of Phone Pairing or Favorites, Last Setting of Volume, Station, App, and Audio Settings Change When Vehicle Shuts Down in Demo Mode and that this is considered a normal ... Read More »
This service bulletin provides repair information on Radio Software Version U168 Update to correct customer concerns of radio software issues. Read More »
This service bulletin provides repair information to correct a customer concern of Radio System Settings Lost or Returning to Default Values. Read More »
This service bulletin provides repair information to correct a customer concern of Radio System Settings Lost or Returning to Default Values. Read More »
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or Non-Responsive to Touch After Cleaning/Disinfecting Radio Display. Read More »
This technical bulletin provides programming information for Radio Software Version U150 Update to correct software issues on infotainment systems IOS, IOT or IOU. Read More »
This technical bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This technical bulletin provides programming information for Radio Software Version U150 Update to correct software issues on infotainment systems IOS, IOT or IOU. Read More »
This Preliminary information communicates an XM service concern of no audio at startup until a channel change and directs to contact XM for direct support. Read More »
This Technical bulletin provides service procedure information for dealers/technicians on Radio Software Version V135116 Over-the-Air Update. Read More »
This Preliminary Information communication advises the technician that the Radio or Tuner, radio controls, Integrated Center Stack, HUD's, IPC's, and radio displays are placed on restriction through the General Motors Technical Assistance ... Read More »
This Preliminary Information communication advises the technician that the Radio or Tuner, radio controls, Integrated Center Stack, HUD's, IPC's, and radio displays are placed on restriction through the General Motors Technical Assistance ... Read More »
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection ... Read More »
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Camera Display. Read More »
This technical bulletin provides programming information for Radio Software Version U150 Update to correct software issues on infotainment systems IOS, IOT or IOU. Read More »
This technical bulletin provides repair information to correct a customer concern of vertical misalignment between cab and pickup box on driver side of vehicle. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and repair of 8 Speed Transmissions Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary information provides information to the technician on installing a roof beacon light. Technician will need to reference the latest version of General Motors Up-fitter Integration Bulletin 157. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This service bulletin announces that the Part Restriction and Ordering Process Information for OnStar? Vehicle Communication Interface Modules (VCIM) (GMNA Only) has ended. Read More »
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to prime the pump. Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This engineering information (EI) is requesting information from the field on vehicles experiencing reduced engine power. GM Engineering needs to gather information to root cause the customer concern and develop a field fix. Read More »
This technical bulletin provides repair information to correct a customer concern of the pickup box endgate will not fully close by itself. Read More »
This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried to shift the t-case from 4lo to Hi gears while driving. Read More »
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This technical bulletin provides repair information to correct a customer concern of Diagnostic Tips For Park Assist Off Message / Unwanted Or False Park Assist Alerts / No DTCs. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This service bulletin provides a service procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3075 Set. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a rubbing type noise heard while turning the steering wheel. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp illuminated on Driver Information Center. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Loss of Power, Instrument Panel Cluster (IPC) Gauges are Inoperative and/or ... Read More »
This engineering information (EI is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to USB Port Does Not Charge or Recognize Phone/Device, or Not Holding Cable in Port, ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a noise heard from the engine compartment, loss of charging and/or reduced ... Read More »
Service Update - Certain 2020 model year Chevrolet Silverado 1500/2500 and GMC Sierra 1500/2500 vehicles may have a condition where the driver side front outboard seat belt may not retract due to a broken rewind spring. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Customer Satisfaction Program. Certain vehicles, equipped with a gas engine, may have a condition in which the printed circuit board inside of the water pump may have been manufactured incorrectly potentially causing a water pump failure. Read More »
This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards a start/stop event or during a normal start using the push button on the dash ... Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This technical bulletin provides repair information to correct a customer concern of Hard Tri-Fold tonneau water leaks at the front corners of the pickup box. Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This Preliminary information communicates multiple vehicle issues caused by an aftermarket device and it gives dealership information where to inspect for this device. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary information communicates that engineering has developed a repair for a chirp noise associated with the front axle assembly. Read More »
This Technical bulletin provides service procedure information for dealers/technicians on Radio Software Version V135116 Over-the-Air Update. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak and/or clunking noise coming from the rear of the vehicle. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This technical bulletin provides repair information to correct a customer concern of the pickup box power endgate may not open on initial press, or may not open at all. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the oil pan. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates to the dealer technician to instruct the customer to use the block heater only at temperatures 0F and below. A calibration will become available at a later date. Read More »
This Preliminary information communicates A vehicle may come into the dealer with a rough idle, lean running concern and/or air leak noise from the PCV system. Read More »
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection ... Read More »
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or Non-Responsive to Touch After Cleaning/Disinfecting Radio Display. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates some diagnostic tips to inspect for no/low voltage at the ECM for a customers complaints of a SES MIL, Crank No Start, stalling DTC's: P16A7 and/or P16AF. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This engineering informational bulletin is requesting information on vehicles with the Service Engine Soon (SES) lamp being illuminated and DTC P1467 set. Read More »
