Technical Service Bulletins (TSBs) for the 2014 S7 are official communications between Audi & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Read More »
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This technical service bulletin provides instructions for troubleshooting and repairing the camshaft adjustment valve to correct a concern about the engine running irregularly. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AND REPAIRING THE CAMSHAFT ADJUSTMENT VALVE TO CORRECT A CONCERN ABOUT THE ENGINE RUNNING IRREGULARLY. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AND REPAIRING THE CAMSHAFT ADJUSTMENT VALVE TO CORRECT A CONCERN ABOUT THE ENGINE RUNNING IRREGULARLY. Read More »
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES. Read More »
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES. Read More »
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 27 number 14-23 dated April 24, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Optimized J931 control module software. Read More »
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 27 number 14-22 dated April 21, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
AUDI: SOME VEHICLES ENGINE WARNING LIGHT SPORADICALLY ILLUMINATES, WOULD HAVE REDUCED PERFORMANCE WITHOUT LOSS OF POWER/STALLING OR NOISE COMING FROM ENGINE COMPARTMENT DUE TO LOW SYSTEM VOLTAGE, AND NOT ENOUGH ON/OFF RATIO TO KEEP FUEL ... Read More »
The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-64 dated June 3, 2015. A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. Read More »
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-99 dated October 16, 2014. The MIL is on. DTCs are stored in the ECM. ECM software adjustment of the secondary air pump motor (V101) runtime during the diagnosis phase. Read More »
A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually only occurs when the engine is warm. The MIL is sporadically on. DTC P2279 and DTC P0507 are stored in the ECM. Read More »
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). Read More »
DTC P218100 will be stored if, after a specified air flow (warm-up phase), the measured engine temperature does not reach the value in the timing map. Read More »
The MIL is on. DTC P310B00 (DFCC 2638) (Low fuel pressure regulation, fuel pressure outside specification) is stored in the engine control module, J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
This communication is to inform you of upcoming Update 24Z6. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
Supersedes Technical Service Bulletin Group 21 number 13-17 dated August 16, 2013. On 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger. Read More »
The crankcase breather is only connected to the bank 2 turbocharger inlet. Blow-by gases from the crankcase breather discolor the pipe (Figure 1). This is a normal condition. Read More »
On 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger. The crankcase breather is only connected to the bank 2 turbocharger inlet. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
Supersedes Technical Service Bulletin Group 01 number 14-88 dated August 15, 2014. The MIL is on. DTC P218100 (Cooling System Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AN ISSUE WITH THE OXYGEN SENSORS THAT CAUSES DTC P013E00 OR P014A00 TO BE STORED. Read More »
Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake ... Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
The MIL is on. DTC P310B00 (DFCC 2638) (Low fuel pressure regulation, fuel pressure outside specification) is stored in the engine control module, J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP
AUDI: SOME VEHICLES ENGINE WARNING LIGHT SPORADICALLY ILLUMINATES, WOULD HAVE REDUCED PERFORMANCE WITHOUT LOSS OF POWER/STALLING OR NOISE COMING FROM ENGINE COMPARTMENT DUE TO LOW SYSTEM VOLTAGE, AND NOT ENOUGH ON/OFF RATIO TO KEEP FUEL ... Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, ... Read More »
The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Read More »
This bulletin contains software update information for the transmission when a bump can be felt just after the vehicle is brought to a stop or when a rattle noise is heard at idle speed. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks ... Read More »
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Read More »
This bulletin contains repair instructions for when DTC P179E00 is stored and the mechantronic unit and/or gear sensor G676 are being replaced. Read More »
Supersedes Technical Service Bulletin Group 27 number 14-23 dated April 24, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Optimized J931 control module software. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". Read More »
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 35 number 12-08 dated December 21, 2012. The driver information system displays the message ?Gearbox malfunction: you can continue driving?. Read More »
In certain operating conditions, a function in the internal thermal management system can increase the engine temperature. Updated engine control module (ECM) software. Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
Supersedes Technical Service Bulletin Group 27 number 14-21 dated February 11, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
Supersedes Technical Service Bulletin Group 27 number 14-22 dated April 21, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. Read More »
Vibrations are felt at 1000 rpm and 3000 rpm. DTCs are stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of ... Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
The dashboard lights and controls may briefly flicker under hard acceleration after downshifting or when the engine is revved while the vehicle is stationary. Read More »
The dashboard lights and controls may briefly flicker under hard acceleration after downshifting or when the engine is revved while the vehicle is stationary. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. Read More »
quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. Read More »
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. Read More »
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed ... Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains software update information for the transmission when a bump can be felt just after the vehicle is brought to a stop or when a rattle noise is heard at idle speed. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the ECM. New ECM software implemented to correct the condition. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-99 dated October 16, 2014. The MIL is on. DTCs are stored in the ECM. ECM software adjustment of the secondary air pump motor (V101) runtime during the diagnosis phase. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Bump felt just after the vehicle is brought to a stop. Rattle noise heard from transmission at idle speed. The software of the transmission mechatronic control module, J743, needs to be updated. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or ... Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or ... Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light ... Read More »
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". Read More »
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake ... Read More »
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
Supersedes Technical Service Bulletin Group 35 number 13-12 dated June 18, 2013. Customer may report that there is oil leaking under the vehicle. Leaking from the oil pan seal. Crack in the oil pan. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. Read More »
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph. Read More »
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the ... Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage. Read More »
This bulletin contains repair instructions for when DTC P179E00 is stored and the mechantronic unit and/or gear sensor G676 are being replaced. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward. Read More »
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has ... Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin. Read More »
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed. Read More »
quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s). Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. Read More »
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Read More »
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. Read More »
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. Read More »
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release ... Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Read More »
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. Read More »
On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. Read More »
This communication is to inform you of upcoming Update 87D9. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
