Technical Service Bulletins (TSBs) for the 2018 CX-9 are official communications between Mazda & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Some customers may complain about a creaking, knocking, rattle or clunk noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure. Read More »
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some vehicles may exhibit one or more of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps at approximate 12 - 25 mph (20 - 40 Km/h). Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (1). This may be caused by the dust boot having insufficient resistance to the cold. Read More »
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. Read More »
Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: 2016-2022 CX-9 2018-2022 CX-5 (Click noise): 1. When first moving forward or reverse from a stop OR 2. Read More »
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: Click Noise: 1. When first moving forward or reverse from a stop OR 2. Read More »
Some vehicles may exhibit a click noise from the front brakes under one of the following conditions: ??A?A? When first moving the vehicle forward or reverse from a stop. Read More »
Some vehicles may exhibit grooves (1) in rear brake disc plate(s), as shown below. This concern is mostly found on new or low mileage vehicles, when the brakes are new. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
Some vehicles may exhibit a squeaking noise from the front brakes during light braking. This concern usually occurs when the front brake pads have been worn to certain levels. Read More »
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
DO NOT follow the instructions on MGSS for performing the ELECTRIC PARKING BRAKE (EPB) FORCED RELEASE PROCEDURE until these instructions are read, otherwise, damage to the EPB system may occur The instructions on MGSS are incorrect in ... Read More »
After parking the vehicle at temperatures below the freezing, some customers may experience a lack of power with the check engine light on and DTC P0638:00 and/or P2112:00 stored in memory. Read More »
Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. Read More »
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
Some customers may experience a check engine light on and DTC P0401:00 stored in memory without any drivability issues. P0401:00 - [PCM] EGR flow insufficient detected. Read More »
After parking the vehicle at temperatures below the freezing, some customers may experience a lack of power with the check engine light on and DTC P0638:00 and/or P2112:00 stored in memory. Read More »
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Read More »
Some customers may experience a lack of power with no warning lights illuminated and no related DTCs stored. This concern most likely occurs when the fuel temperature is high and during situations where high power is required. Read More »
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head. Read More »
Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P0301:00, P0302:00, P0303:00, P0304:00.NOTE: Only turbo engines are applicable; non-turbo engines are NOT applicable. Read More »
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Read More »
Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P030X:00 (only turbo engines are applicable; non-turbo engines are NOT applicable). Read More »
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Read More »
The WSM shows 3 possible crankshaft sprocket and timing chain combinations (Type A, B and C), but some vehicles have been produced with a combination of Type A timing chain with 2 yellow-colored links with a Type B crankshaft sprocket. Read More »
Coolant Leaks At Cylinder Head: Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
Coolant Leaks At Cylinder Head: Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
Some vehicles may exhibit the CHECK ENGINE light on with DTC P011B:00 (Engine coolant temperature/IAT: Correlation error) when using an engine block heater which is set up by MCI as local accessory parts. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
Some vehicles may exhibit an occasional rough idle accompanied with DTC P0300:00 (Random misfire) due to the following: 1. While closing the EGR valve, carbon deposit etc. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
Some vehicles may exhibit an occasional rough idle accompanied with DTC P0300:00 (Random misfire) due to the following: 1. While closing the EGR valve, carbon deposit etc. Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Read More »
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
If you encounter sputtering, surging or poor driveability with the following DTCs stored, inspect the MAP sensor connection for corroded terminals (as shown below). Recommend replacing the engine wire harness and MAP sensor. Read More »
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
After parking the vehicle in temperatures below freezing, some customers may experience a lack of power with the check engine light on and DTCs P0638:00 and/or P2112:00 stored in memory. Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
While inspecting turbocharger housings, you may see cracks (fractures) as shown below. The cracks do not affect engine performance or cause any noise, so replacement is NOT necessary. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). Read More »
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Read More »
While inspecting turbocharger housings, you may see cracks (fractures) as shown below. The cracks do not affect engine performance or cause any noise, so replacement is NOT necessary. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
The 2018 CX-9 Maintenance Monitor engine oil data reset procedure (for oil change) is different than other models due to a specification problem. It must be reset in 2 places - in MAZDA CONNECT and in the instrument cluster. Read More »
ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
While inspecting turbocharger housings, you may see cracks (fractures) as shown below. The cracks do not affect engine performance or cause any noise, so replacement is NOT necessary. Read More »
ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL
Some vehicles may exhibit a rattle, clunk or pop noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head. Read More »
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Read More »
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely ... Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
After parking the vehicle at temperatures below the freezing, some customers may experience a lack of power with the check engine light on and DTC P0638:00 and/or P2112:00 stored in memory. Read More »
Some vehicles may exhibit a fuel odor at the left / rear area of the vehicle while the engine is idling that usually occurs when the fuel tank is warmed up in hot weather and/or after long distance driving. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
Some customers may experience a lack of power with no warning lights illuminated and no related DTCs stored. This concern most likely occurs when the fuel temperature is high and during situations where high power is required. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
The SKYACTIV?-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV? oil filters. The unique oil filter can be identified with two white bands as shown below. Read More »
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
The rear differential case could develop a crack in the case. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
The rear differential case could develop a crack in the case NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
Some customers may experience a squeaking noise may be heard from the exhaust manifold when the idle speed drops from fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. Read More »
Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration. Read More »
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
Some customers may experience a lack of power with no warning lights illuminated and no related DTCs stored. This concern most likely occurs when the fuel temperature is high and during situations where high power is required. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. Read More »
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
Some customers may experience electrical devices that cannot be charged through the rear console or the trunk side trim USB power outlet. This may be caused by an excessive external force applied to the USB power outlet. Read More »
Some customers may experience electrical devices that cannot be charged through the rear console or the trunk side trim USB power outlet. This may be caused by an excessive external force applied to the USB power outlet. Read More »
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.324 or later). The system performance has been improved as follows: Ver. 74.00. Read More »
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of ... Read More »
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * ... Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.311 or later). Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage. Read More »
Some customers may complain about an inoperative power liftgate (PLG) and the any of the following DTC's stored in memory: ??A?A? U3003:16 (Power liftgate (PLG) control module power supply voltage low input) ??A?A? U3003:17 (Power ... Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
After parking the vehicle in temperatures below freezing, some customers may experience a lack of power with the check engine light on and DTCs P0638:00 and/or P2112:00 stored in memory. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
The instructions in the current inventory of the Rear Seat Entertainment (RSE) System are incorrect in some of the steps and have been updated. The P/N of the updated instructions is 0000-8F-N10A. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g. Read More »
DO NOT follow the instructions on MGSS for performing the ELECTRIC PARKING BRAKE (EPB) FORCED RELEASE PROCEDURE until these instructions are read, otherwise, damage to the EPB system may occur The instructions on MGSS are incorrect in ... Read More »
MAZDA MOBILE START (MMS) APP ERROR MESSAGE INSTALLED ON ANDROID DEVICES: Customers may get an error message "Device no longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Read More »
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
POWER LIFTGATE INOPERATIVE WITH DTC U3003:16: Some customers may complain about an inoperative power liftgate (PLG) with DTC U3003:16 (Power liftgate (PLG) control module power supply voltage low input) is stored in memory. Read More »
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.546 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
MAZDA CONNECT SOFTWARE VERSION 59.00.545 AVAILABLE. An update to the MAZDA CONNECT system is now available for download from the Mazda Global Service Support (MGSS) system. The new version number is 59.00.545. Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
After parking the vehicle at temperatures below the freezing, some customers may experience a lack of power with the check engine light on and DTC P0638:00 and/or P2112:00 stored in memory. Read More »
When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping. Read More »
If the BSM control module is replaced, Auto Configuration and BSM Radar Test must be performed: 1. Auto Configuration -When the ignition is switched ON, the blind spot monitoring (BSM) reads the vehicle specification information sent via ... Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
If you encounter sputtering, surging or poor driveability with the following DTCs stored, inspect the MAP sensor connection for corroded terminals (as shown below). Recommend replacing the engine wire harness and MAP sensor. Read More »
Due to a change in the 2017 Mazda3, Mazda6 and 2018 CX-9 A-pillar wiring harness, the EC Mirror w/compass / EC Mirror w/compass + Homelink installation instructions have been updated. Read More »
Some vehicles may exhibit an unusual noise in the front A/C unit when the recirculate switch is operated. This is caused by a damaged gear in the air intake actuator. Read More »
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is? 2017 Mazda North American Operations, U.S.A. Read More »
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
Upgrade your PCs to IDS version 109.00 and 109.01 from the previous version. NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108. Read More »
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.504 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
Dealer Rework (DRW) 13 ? Mazda Connect Navigation Concern 2018MY CX-5, CX-3, CX-9, Mazda6, Mazda 3 and MX-5: We write to inform you that certain vehicles are affected by the concern mentioned below. Read More »
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found. Read More »
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during extremely cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. Read More »
Some customers may complain that the Voice Recognition system does not recognize "Address" or "NewDestination" navigation voice commands. This may be caused by faulty navigation SD card software. Read More »
Some vehicles may exhibit the CHECK ENGINE light on with DTC P011B:00 (Engine coolant temperature/IAT: Correlation error) when using an engine block heater which is set up by MCI as local accessory parts. Read More »
When performing the MGSS Workshop Manual 360??A? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
When performing the MGSS Workshop Manual 360??A? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
Due to a change in the 2017 Mazda3, Mazda6 and 2018 CX-9 A-pillar wiring harness, the EC Mirror w/compass / EC Mirror w/compass + Homelink installation instructions have been updated. Read More »
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
Rusty Panel at Bottom (Inner Side) of Doors: Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. Read More »
Rusty Panel at Bottom (Inner Side) of Doors: Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. Read More »
Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. It is caused by mud/sand adhering to the side sill, which scratches the paint surface when the door is opened/closed. Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
Some vehicles may exhibit a rattle, clunk or pop noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts. Read More »
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in cold weather areas just after the RAPGARD is removed at PDI. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
Mazda Accessories has re-released the Front and Rear Bumper Trim kits for the CX-9 (see the table below for application and required components). Read More »
Some customers may notice cracks (as shown below) at one or both ends of the front bumper near the front fender / front combination light. This may be caused when driving over bumps. Read More »
Some customers may notice cracks at one or both ends of the front bumper near the front fender / front combination light. This may be caused when driving over bumps. Read More »
Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become ... Read More »
Some customers may complain that the door weatherstrip (1) comes off at the front / lower part of the rear door(s). This concern is caused by insufficient weatherstrip gripping force. Read More »
Some customers may complain that the door weatherstrip (1) comes off at the front / lower part of the reardoor(s). This concern is caused by insufficient weatherstrip gripping force. Read More »
Some customers may complain that the door weatherstrip (1) comes off at the front / lower part of the reardoor(s). This concern is caused by insufficient weatherstrip gripping force. Read More »
Some vehicles may exhibit a creaking or clacking noise when operating the power lift gate (PLG). The noise may be caused by the following: Creaking noise: Dust and dirt accumulates on the sealing portion of the PLG drive unit, reducing ... Read More »
While stopped with the transmission in Park position, some vehicles may exhibit concerns that the liftgate unlatches itself without pressing the liftgate opener switch (1) or it will not unlatch when pressing the liftgate opener switch (1). Read More »
POWER LIFTGATE INOPERATIVE WITH DTC U3003:16: Some customers may complain about an inoperative power liftgate (PLG) with DTC U3003:16 (Power liftgate (PLG) control module power supply voltage low input) is stored in memory. Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
Some vehicles may exhibit a creaking or clacking noise when operating the power lift gate (PLG). The noise may be caused by the following: Creaking noise: Dust and dirt accumulates on the sealing portion of the PLG drive unit, reducing ... Read More »
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. Read More »
While stopped with the transmission in Park position, some vehicles may exhibit concerns that the liftgate unlatches itself without pressing the liftgate opener switch (1) or it will not unlatch when pressing the liftgate opener switch (1). Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
Mazda is incorporating a "Direct" type TPMS, which is unlike the previous "Indirect" type system. With the "Direct" type TPMS........ ? there is no TPMS switch on the dashboard. It is no longer needed. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some vehicles may exhibit corrosion of the wheel nuts. This is caused by torsional stress concentrating on the tip of the wheel nut because of the thin and long shape of the nut, which damages the coating and causes the corrosion. Read More »
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some vehicles with accessory installed wheel locks may have had the wrong kit installed using a 21 mm wheel lock key. As of May 01, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Mazda is incorporating a "Direct" type TPMS, which is unlike the previous "Indirect" type system. With the "Direct" type TPMS........ ? there is no TPMS switch on the dashboard. It is no longer needed. Read More »
Some vehicles with accessory installed wheel locks may have had the wrong kit installed using a 21 mm wheel lock key. As of May 01, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with ... Read More »
FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: The ... Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
Some vehicles may exhibit the rear parking sensor beeping without any obstacles behind it when the shift lever is shifted into Reverse. This concern only occurs when the rear USB power outlet (1) is broken. Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
Some customers may complain about poor A/C performance due to low refrigerant. This may be caused by the low-temperature side outlet pipe leading to the evaporator of the air conditioner condenser deteriorating because the structure ... Read More »
Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: 2016-2022 CX-9 2018-2022 CX-5 (Click noise): 1. When first moving forward or reverse from a stop OR 2. Read More »
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
Some vehicles may exhibit a rattle, clunk or pop noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
This service bulletin provides information regarding the proper use of the driver??A?A?s floor mat to avoid any potential interference with the foot pedals. Read More »
This service bulletin provides information regarding the proper use of the driver??A?A?s floor mat to avoid any potential interference with the foot pedals. Read More »
Some customers may complain that the rear console / cup holder area is warming. The warming is caused by heat radiating from the rear heater core, which is located under the console. Read More »
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section ... Read More »
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage. Read More »
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method Read More »
Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method Read More »
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay??A?A? / Android Auto??A?A?, but it can be activated using MDARS. Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all ... Read More »
Some vehicles may exhibit a rattle, clunk or pop noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts. Read More »
CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become ... Read More »
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
Some customers may complain that the rear console / cup holder area is warming. The warming is caused by heat radiating from the rear heater core, which is located under the console. Read More »
Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: Click Noise: 1. When first moving forward or reverse from a stop OR 2. Read More »
If you encounter sputtering, surging or poor driveability with the following DTCs stored, inspect the MAP sensor connection for corroded terminals (as shown below). Recommend replacing the engine wire harness and MAP sensor. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
The instructions in the current inventory of the Rear Seat Entertainment (RSE) System are incorrect in some of the steps and have been updated. The P/N of the updated instructions is 0000-8F-N10A. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
When troubleshooting a radar unit, DO NOT swap it with another vehicle. Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Read More »
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
Some customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display. Read More »
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
Mazda is incorporating a "Direct" type TPMS, which is unlike the previous "Indirect" type system. With the "Direct" type TPMS........ ? there is no TPMS switch on the dashboard. It is no longer needed. Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
The 2018 CX-9 Maintenance Monitor engine oil data reset procedure (for oil change) is different than other models due to a specification problem. It must be reset in 2 places - in MAZDA CONNECT and in the instrument cluster. Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
The instructions in the current inventory of the Rear Seat Entertainment (RSE) System are incorrect in some of the steps and have been updated. The P/N of the updated instructions is 0000-8F-N10A. Read More »
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
Some vehicles may exhibit BLUETOOTH? hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH? hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program ... Read More »
Due to a change in the 2017 Mazda3, Mazda6 and 2018 CX-9 A-pillar wiring harness, the EC Mirror w/compass / EC Mirror w/compass + Homelink installation instructions have been updated. Read More »
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
Dealer Rework (DRW) 13 - Mazda Connect Navigation Concern. As you may know, DRW13 was launched in March of 2018. This notice is to advise all dealers that DRW13 will be ending August 16th 2018 and all claims must be submitted by this date. Read More »
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found. Read More »
Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. Read More »
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
Some vehicles may exhibit the CHECK ENGINE light on with DTC P011B:00 (Engine coolant temperature/IAT: Correlation error) when using an engine block heater which is set up by MCI as local accessory parts. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
The owner??A?A?s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Read More »
The navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Read More »
The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. Read More »
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: 2016-2022 CX-9 2018-2022 CX-5 (Click noise): 1. When first moving forward or reverse from a stop OR 2. Read More »
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
Some vehicles may exhibit a rattle, clunk or pop noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts. Read More »
Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
When performing the MGSS Workshop Manual 360??A? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become ... Read More »
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: Click Noise: 1. When first moving forward or reverse from a stop OR 2. Read More »
Some vehicles may exhibit a click noise from the front brakes under one of the following conditions: ??A?A? When first moving the vehicle forward or reverse from a stop. Read More »
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. Read More »
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. Read More »
The 2018 CX-9 Maintenance Monitor engine oil data reset procedure (for oil change) is different than other models due to a specification problem. It must be reset in 2 places - in MAZDA CONNECT and in the instrument cluster. Read More »
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
Some vehicles may exhibit an unusual noise in the front A/C unit when the recirculate switch is operated. This is caused by a damaged gear in the air intake actuator. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
