Technical Service Bulletins (TSBs) for the 2008 Sierra 2500 are official communications between GMC & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
This technical bulletin provides repair information for installing a new stabilizer shaft bracket to correct a customer concern of on a clunking noise originating from the front of the vehicle that is more predominant during turns or ... Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid. Read More »
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
GENERAL MOTORS: DIAGNOSING POWER STEERING CONCERNS. IN RARE CASES, CUSTOMERS MAY COMMENT ON A LACK OF STEERING ASSIST WHEN STOPPED OR DURING PARKING LOT TYPE OF MANEUVERS. *JS UPDATED 09/02/14*LJ Read More »
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section. Read More »
This informational bulletin provides information for Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions Read More »
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid. Read More »
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid. Read More »
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Read More »
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS TO DIAGNOSIS AND REPAIR VEHICLES WITH VARIOUS HANDLING, VEHICLE DYNAMICS CONCERNS, NOISES FROM THE SUSPENSION OR UNDERBODY, OR ISSUES RELATED ... Read More »
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related ... Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related ... Read More »
This preliminary informational bulletin provides technicians a recommendation for when they are performing a front end alignment and find an alignment dowel pin missing . Read More »
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension. Read More »
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension. Read More »
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal. Read More »
This preliminary informational bulletin provides technicians a recommendation for when they are performing a front end alignment and find an alignment dowel pin missing . Read More »
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension. Read More »
This technical bulletin adds the 2016 model year to repair information for lubricating the rear leaf springs to correct a customer concern for a squeak noise from rear of vehicle. Read More »
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension. Read More »
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
CHEVROLET/GMC: A WHINE, GRIND OR CLUNK NOISE FROM THE REAR AXLE AT SPEEDS ABOVE APPROXIMATELY 30 MPH (50KPH). THIS CONDITION ONLY APPLIES TO 10.5 REAR AXLE ASSEMBLIES, WHICH ARE USED ON 2500 AND 3500 SERIES PICKUPS EQUIPPED WITH A 5. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a Antilock Braking System Malfunction Indicator Lamp on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise from the right front fender area on hard acceleration or when brake torqueing. Read More »
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Read More »
This technical bulletin provides a procedure to either refinish or replace the front rotors for a condition of brake induced pulsation, vibration felt in steering wheel, rumble noise from underbody during downhill descents. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Brake Pedal Position and or Cruise Brake Pedal parameters are showing "Applied" with the brake pedal released. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Read More »
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Technical bulletin provides a procedure to correct a condition of Active Fuel Management (AFM) Engine Valve Lifter Tick Noise at Start Up When Engine Has Been Off for 2 Hours or More. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. Read More »
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2? or GDS 2 (U.S. and Canada) Read More »
This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Read More »
Clean Exhaust Filter see owners manual now or cleaning exhaust filter keep driving until message is cleared displayed on DIC, DTC P2463 May be set Read More »
This Preliminary Information communication provides information to the technician about vehicles that engine runs and idles rough. Technician will find P0171 and or P0174. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. Read More »
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Read More »
This informational bulletin provides technicians with information to help educate them on the many various combinations of engines, interfacing equipment and vehicle usage which may cause higher than expected oil consumption. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. Read More »
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
This informational bulletin provides additional information on identifying duramax aftermarket power up devices that may cause damage to the engine and not covered under warranty. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines. Read More »
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2A? or global diagnostic system 2 ... Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This technical bulletin provides a procedure to install AFM oil deflector, rocker arm cover-left bank and clean carbon from cylinder due to engine oil consumption on aluminum block/iron block engines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This technical bulletin provides a procedure to install the updated valve cover for models built with the prior date listed to correct oil consumption of vehicles with higher mileage. Read More »
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. Read More »
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0011. Read More »
This preliminary informational bulletin provides a diagnostic tip for coolant leak at oil cooler inlet pipe o-ring after service engine replacement. Read More »
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2? or GDS 2 (U.S. and Canada). Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This preliminary bulletin provides a procedure to install a new design upper intake manifold with a new MAP sensor relocated to prevent ice build up and setting code P0106. Read More »
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Read More »
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. Read More »
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Read More »
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Read More »
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils. Read More »
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Read More »
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set. Read More »
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2 Read More »
This informational bulletin provides Information on Identifying Duramax Diesel Overpower Engine Breakdown/Non-Function Due to Aftermarket Power-Up Devices vs Non Overpower Engine Non-Function of Pistons, Cylinders, Valvetrain Components, ... Read More »
This technical bulletin provides a procedure to replace the AFM oil deflector, rocker arm cover and clean the carbon deposits for conditons related to Engine Oil Consumption on Aluminum Block/Iron Block Engines with Active Fuel ... Read More »
CHEVROLET/GMC: SNOW OR ICE INGESTION INTO AIR CLEANER ELEMENT, MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED, ENGINE POWER IS REDUCED MESSAGE DISPLAYED, DTC P0101 SET (PERFORM REPAIR AS OUTLINED). Read More »
CHEVROLET SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ECM EEPROM - REPROGRAM ECM. ALL 2007 AND CERTAIN 2008 CHEVEROLET SILVERADO AND EXPRESS AND GMC SIERRA AND SAVANA EQUIPPED WITH 6. Read More »
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2? or GDS 2 (U.S. and Canada). Read More »
ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled ... Read More »
This preliminary informational bulletin provides dealership personnel with policies and procedures regarding damaged, disassembled or improperly packaged turbochargers returned to Warranty Part Center. Read More »
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled ... Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramax? diesel engines ? Photograph Tech 2? Calibration IDs, Calibration Verification Numbers ... Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This informational bulletin provides information for Identifying Non-GM ECM Calibration Use and Power-up Hardware Detection in Duramax Diesel Engines - Photograph Tech 2 Calibration IDs, Calibration Verification Numbers (CVNs) and ... Read More »
CHEVROLET/GMC: SNOW OR ICE INGESTION INTO AIR CLEANER ELEMENT, MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED, ENGINE POWER IS REDUCED MESSAGE DISPLAYED, DTC P0101 SET (PERFORM REPAIR AS OUTLINED). Read More »
ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER
14581 - EMISSION RECALL. GENERAL MOTORS HAS DECIDED TO CONDUCT A VOLUNTARY EMISSION RECALL INVOLVING CERTAIN 2008 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, AND TAHOE; AND GMC SIERRA, YUKON, AND YUKON XL VEHICLES EQUIPPED WITH CALIFORNIA ... Read More »
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled ... Read More »
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication advises the technician of two types of DEX-COOL 50/50 Premix are available through General Motors Service Parts Operations, one with bitterant and one without. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in Three or Four Cylinder Mode. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
This technical bulletin provides a procedure to correct the customers concern to replace the left side valve cover and active fuel management oil deflector to reduce oil consumption. Read More »
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. Read More »
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This SKU is a Diesel Fuel Filter Housing. The customer communication requested return of unsold inventory to inspect the fuel filter threads. The threads may be misformed such that the fuel filter cannot be installed. Read More »
This SKU is a Diesel Fuel Filter Housing. The customer communication requested return of unsold inventory to inspect the fuel filter threads. The threads may be misformed such that the fuel filter cannot be installed. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an engine noise, low oil pressure, over-speed condition, or abnormal oil sludge build up in the crankcase. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. Read More »
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This informational bulletin provides information for Identifying Non-GM ECM Calibration Use and Power-up Hardware Detection in Duramax Diesel Engines - Photograph Tech 2 Calibration IDs, Calibration Verification Numbers (CVNs) and ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician about a customer?s request to remove or disable the Bi-Fuel Compressed Natural Gas system. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that after refueling the fuel gauge will show empty. Technician will find Diagnostic Trouble Code P2636. Read More »
FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Read More »
This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification. Read More »
This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
Slips in Reverse or Third, Delayed Reverse or Drive Engagement, DTC P0776, P2715,P2723, Harsh 2-3 Shifts (Inspect 1-2-3-4 / 3-5-R Housing and Pump Seal Rings) Read More »
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Read More »
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2A? or global diagnostic system 2 ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a surge or stall when in gear at a stop. Technician will find Diagnostic Trouble Code P0742. Read More »
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case. Read More »
This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken. Read More »
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set. Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Read More »
This technical bulletin provides a procedure to install a 3-5-rev clutch housing inspection and repair to correct the customers concern of Slips in Reverse or Third, Delayed Reverse or Drive Engagement and MIL on. Read More »
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change. Read More »
This technical bulletin provides a procedure to install a 3-5-rev clutch housing inspection and repair to correct the customers concern of Slips in Reverse or Third, Delayed Reverse or Drive Engagement and MIL on. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. Read More »
This Preliminary Information communication provides information to the technician about vehicle with a clunk type noise on start up with the vehicle in park when the vehicle is equipped Allison LCT1000 transmission. Read More »
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a clunk type noise on start up with the vehicle in park when the vehicle is equipped Allison LCT1000 transmission. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a clunk type noise on start up with the vehicle in park when the vehicle is equipped Allison LCT1000 transmission. Read More »
This preliminary information bulletin provides a procedure to adjust the transmission dipstick tube and/or install the transmission fluid filler tube sleeve to eliminate a tick, buzz or rattle noise from the front of dash, transmission ... Read More »
This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken. Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
GMC: FLARE AND OR HARSH 2-3 SHIFTS. THIS CONDITION MAY BE CAUSED BY LEAKING 1-2-3-4 AND 3-5-R CLUTCH FLUID SEAL RINGS (230). MODELS CADILLACS, CHEVROLETS, GMC, HUMMERS, PONTIACS. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. Read More »
CHEVROLET\GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. TRANSMISSION OVERHEAT IN EXTREME COLD AMBIENT TEMPERATURES - REPROGRAM TCM. LOCATED IN ALASKA AND MINNESOTA; CANADIAN YUKON AND NORTHWEST TERRITORIES ONLY. Read More »
GENERAL MOTORS: ENGINE RUNNING WITH KEY OFF, CONTINUOUS RUN; SENSING DIAGNOSTIC MODULE (SDM), NO COMMUNICATION, SERVICE AIR BAG LIGHT ILLUMINATED (INSTALL DIODE TO SOLENOID/RELAY). *PE Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have no forward or reverse. Technician will need to check for metal debris in torque converter clutch valve. Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service 4WD light on and the system inoperative. Technician may find Diagnostic Trouble Code B2725 set. Read More »
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Read More »
CHEVROLET\GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. FRONT AXLE VENT TUBE KINKED - FLUID LEAK. *NJ CSC WAS RECEIVED. UPDATED 4/24/08. *NJ Read More »
This Preliminary Information communication provides information to the technician about vehicles that have the transfer case is inoperative, difficult to shift or has no torque to the front prop shaft after 4wd is engaged. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This technical bulletin provides repair information to correct a customer concern of Clock Shows Dashes and Cannot be Set After Battery Disconnect. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This preliminary bulletin provides a procedure to install adhesive back stock to the electrical connector for the steering wheel position sensor, to eleminate the excessive clearance/movement that causes the connector to loose contact and ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications Read More »
This Preliminary Information communication advises the technician certain accessories are being made available through the Integrated Business Partner. Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have windows inoperative while the engine is running but work when the engine is off. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramax? diesel engines ? Photograph Tech 2? Calibration IDs, Calibration Verification Numbers ... Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Read More »
This informational bulletin provides information for installing a diode to solenoid/relay to suppress voltage spikes in conjuction with installation of electrical aftermarket accessories-battery, ignition and ground feeds-(do not splice ... Read More »
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only). Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE DRIVE MOTOR GENERATOR CONTROL MODULE AND ACCESSORY POWER MODULE ARE BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. Read More »
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty. Read More »
This informational bulletin adds models to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging. Read More »
This informational bulletin adds 2011 - 2014 model years to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vehicles that will not crank intermittently due to a dead battery. Read More »
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer Read More »
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer Read More »
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the check engine light, tow/haul, Supplemental Inflatable Restraint, cruise control or other various indicators or warning ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Read More »
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the ... Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an aftermarket, add-on back up alarm will sound when unlocking the doors with the Remote Keyless Entry remote. Read More »
This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an engine misfire, oil consumption, and/or a Service Engine Soon Malfunction Indicator Lamp on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a malfunction indicator light or service anti-lock brake system message displayed in the Driver Information Center. Read More »
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code B2555 may be found in a Driver and/or Passenger Door Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a surge or stall when in gear at a stop. Technician will find Diagnostic Trouble Code P0742. Read More »
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection ... Read More »
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the ... Read More »
This informational bulletin provides information on Available BCM Calibrations to Restore Bulb Outage Detection on Vehicles Produced by a Second Stage Manufacturer (Upfitter), Turn Signals Flash Fast after Factory Box ... Read More »
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY. Read More »
This informational bulletin provides information for installing a diode to solenoid/relay to suppress voltage spikes in conjuction with installation of electrical aftermarket accessories-battery, ignition and ground feeds-(do not splice ... Read More »
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that will not crank intermittently due to a dead battery. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the ... Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not Read More »
GMC/CHEVROLET: SEE DOCUEMTN SEARCH BUTTON FOR OWNER LETTER. AUXILIARY BATTERY FEED MAY CAUSE FUSIBLE LINK TO MELT AND OPEN CIRCUIT TO PREVENT DAMAGE OR FIRE IN WIRING HARNESS, DUE TO ELECTRICAL OVER LOAD. Read More »
This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement. Read More »
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are ... Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an engine misfire, oil consumption, and/or a Service Engine Soon Malfunction Indicator Lamp on. Read More »
This Preliminary Information communication provides information to the technician that during the Pre-Delivery Inspection it may be noticed that the backup alarm is inoperative. Read More »
This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices causing multiple issues. Read More »
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). Read More »
VARIOUS ELECTRICAL CONCERNS - INTERMITTENTLY FUNCTIONING OR INOPERATIVE COMPONENT, IP WARNING LIGHT ON, DIC MESSAGE DISPLAYED, DTC SET, NO CRANK/START (REPAIR IP WIRING HARNESS) *NJ Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
"09184C - CUSTOMER SATISFACTION PROGRAM (REVISED SERVICE PROCEDURE). THIS BULLETIN HAS BEEN REVISED TO CLARIFY STEP 5 OF THE SERVICE PROCEDURE. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs) Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. Read More »
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Read More »
This Preliminary Information communication advises the technician when replacing the accessory headrest digital video disc monitor to check the control module manufacture part number. Read More »
This Preliminary Information communication provides information to the technician about vehicle starts and stalls on the first initial start after the replacement of the Theft Deterrent Module. Read More »
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only). Read More »
This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This informational bulletin provides additional information on identifying duramax aftermarket power up devices that may cause damage to the engine and not covered under warranty. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491). Read More »
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This informational bulletin provides information on Available BCM Calibrations to Restore Bulb Outage Detection on Vehicles Produced by a Second Stage Manufacturer (Upfitter), Turn Signals Flash Fast after Factory Box ... Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This technical bulletin provides repair information for low beam headlamp bulb diagnosis/replacement to correct a customer concern that the low beam headlamp is inoperative. Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer Read More »
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This Preliminary Information communication provides information to the technician about vehicles with the inside door panel material appearing to be pulling back from the door panel backing. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have windows inoperative while the engine is running but work when the engine is off. Read More »
This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance. Read More »
This technical bulletin provides a procedure to install double sided tape to the windshield molding to correct the customers concern of a tapping or clicking noise at the winshield area. Read More »
This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not replace any glass for this reason. Read More »
This technical bulletin provides a procedure for adding double sided tape on the right and left windshield side reveal moldings to remove tapping, clicking or ticking type noise. Read More »
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT. Read More »
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. Read More »
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions. Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have a whistle noise coming from the driver?s side "A" pillar area when driving around 50 mph with the Heater-Vent-Air Conditioning ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have reduced air flow from the Heater-Vent-Air Conditioning dash vents. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This service bulletin provides information on Takata Air Bag Courtesy Transportation Reimbursement Program - Applicable to GM Recalls listed in bulletin. Read More »
This service bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM Recalls 14491, 14735,15040, 15041, 15043,15044, 15045, 15046, 15406,15438, 15442, 15815, 15816,15817, 15818, 15826, 17009, ... Read More »
This informational bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM Recalls 14491, 14735, 15040, 15041, 15043, 15044, 15045, 15046, 15047, 15048, 15049, 15050, 15052, 15053, 15406, ... Read More »
This informational bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM Recalls 14491, 14735, 15040, 15041, 15043, 15044, 15045, 15046, 15406, 15438, 15442, 15815, 15816, 15817, 15818, ... Read More »
This informational bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM Recalls 14491, 14735, 15040, 15041, 15043, 15044, 15045, 15046, 15406, 15438, 15442, 15815, 15816, 15817, 15818, ... Read More »
This informational bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM Recalls 14491, 14735, 15040, 15041, 15043, 15044, 15045, 15046, 15406, 15438, 15442, 15815, 15816, 15817, 15818, ... Read More »
This informational bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM Recalls 14491, 14735, 15041, 15043, 15406, 15438, 15815, 15816, 15817, 15826, 17009, 28810 and ... Read More »
This technical bulletin provides a procedure to complete a terminal replacement or connector re connection to correct a condition of Diagnostic Information for Supplemental Inflatable Restraint (SIR) System, Intermittent AIR BAG ... Read More »
This Preliminary Information communication provides information to the technician about the passenger presence system, passenger air bag on/off indicators, passenger air bag on/off switch, and passenger seat belt indicator. Read More »
GENERAL MOTORS: ENGINE RUNNING WITH KEY OFF, CONTINUOUS RUN; SENSING DIAGNOSTIC MODULE (SDM), NO COMMUNICATION, SERVICE AIR BAG LIGHT ILLUMINATED (INSTALL DIODE TO SOLENOID/RELAY). *PE Read More »
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices Read More »
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button ... Read More »
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Read More »
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer Read More »
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Read More »
This preliminary information bulletin provides information on installing new rivets on the accessory tonneu cover to correct a customers comments on the cover seeming loose Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have raised dents or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Read More »
This technical bulletin provides a procedure on how to install a lower cross member to correct the condition of if the cross member rusts away. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube ... Read More »
This Preliminary Information communication provides information to the technician about vehicles with the inside door panel material appearing to be pulling back from the door panel backing. Read More »
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code B2555 may be found in a Driver and/or Passenger Door Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
UNABLE TO DISABLE AUTO DOOR LOCKS. THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. Read More »
UNABLE TO DISABLE AUTO DOOR LOCKS. THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code B2555 may be found in a Driver and/or Passenger Door Module. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
GENERAL MOTORS: DIAGNOSING POWER STEERING CONCERNS. IN RARE CASES, CUSTOMERS MAY COMMENT ON A LACK OF STEERING ASSIST WHEN STOPPED OR DURING PARKING LOT TYPE OF MANEUVERS. *JS UPDATED 09/02/14*LJ Read More »
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty. Read More »
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on. Read More »
This informational bulletin provides the proper information used to determine the road force variences within new tires being installed and the proper forms used to send the tires back if the road force is not within spec. Read More »
This informational bulletin provides the proper information used to determine the road force variences within new tires being installed and the proper forms used to send the tires back if the road force is not within spec. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes. Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires. Read More »
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have raised dents or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Read More »
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted. Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on. Read More »
This Preliminary Information communication provides information to the technician that replacement transfer case halves will not be threaded. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This Preliminary Information communication provides information to the technician about the passenger presence system, passenger air bag on/off indicators, passenger air bag on/off switch, and passenger seat belt indicator. Read More »
This Preliminary Information communication provides information to the technician about vehicles that after installing the GM Accessory Heated Seat Kit, one or more of the following issues may be present the heated seat back and/or bottom ... Read More »
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices Read More »
This preliminary informational bulletin provides a revision of PI0639B to add the 2013 model year and update the labor operation information. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This information bulletin explains the use of drilling high strength steel in a collision repair and the GM recommended CryoCobalt Drill bit. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Read More »
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Read More »
BACK OVER PREVENTION:WARNINGS:EXTERNAL/PEDESTRIAN ALERT
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This technical bulletin provides repair information to correct a customer concern of Clock Shows Dashes and Cannot be Set After Battery Disconnect. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Read More »
This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in Three or Four Cylinder Mode. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This technical bulletin provides repair information for installing a new stabilizer shaft bracket to correct a customer concern of on a clunking noise originating from the front of the vehicle that is more predominant during turns or ... Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be Set. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
44180 01 - Customer Satisfaction - Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an engine noise, low oil pressure, over-speed condition, or abnormal oil sludge build up in the crankcase. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be ... Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
Clean Exhaust Filter see owners manual now or cleaning exhaust filter keep driving until message is cleared displayed on DIC, DTC P2463 May be set Read More »
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramax? diesel engines ? Photograph Tech 2? Calibration IDs, Calibration Verification Numbers ... Read More »
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores. Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder. Read More »
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications. Read More »
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only). Read More »
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only). Read More »
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE DRIVE MOTOR GENERATOR CONTROL MODULE AND ACCESSORY POWER MODULE ARE BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. Read More »
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar RemoteLink? phone application. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This informational bulletin provides additional information on identifying duramax aftermarket power up devices that may cause damage to the engine and not covered under warranty. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply. Read More »
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have a whistle noise coming from the driver?s side "A" pillar area when driving around 50 mph with the Heater-Vent-Air Conditioning ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the check engine light, tow/haul, Supplemental Inflatable Restraint, cruise control or other various indicators or warning ... Read More »
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This informational bulletin provides information for Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions Read More »
This preliminary informational bulletin provides a revision of PI0639B to add the 2013 model year and update the labor operation information. Read More »
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making. Read More »
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information. Read More »
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission. Read More »
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is ... Read More »
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This informational bulletin provides information on Available BCM Calibrations to Restore Bulb Outage Detection on Vehicles Produced by a Second Stage Manufacturer (Upfitter), Turn Signals Flash Fast after Factory Box ... Read More »
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only. Read More »
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only. Read More »
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service. Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This Preliminary Information communication advises the technician that the Valve Assembly part number 24255209 and Valve Body part number 29544409 have been removed from the General Motors Product Quality Center parts restriction. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After an OnStar In-Vehicle Voice Message Is Heard. Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Read More »
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Read More »
This technical bulletin provides a procedure to complete a terminal replacement or connector re connection to correct a condition of Diagnostic Information for Supplemental Inflatable Restraint (SIR) System, Intermittent AIR BAG ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Read More »
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS. Read More »
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs) Read More »
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar ... Read More »
This preliminary informational bulletin provides repair information to correct a customer concern of poor radio hands-free voice recognition performance or sound quality after OnStar upgrade. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Read More »
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a radio display that will show "LOCKED" or "THEFT LOCK". Read More »
This Preliminary Information communication provides information to the technician about vehicles that have navigation or radio screen is blank or flashes on and off, no sound from speakers, and rear DVD screen inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a radio display that will show "LOCKED" or "THEFT LOCK". Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have navigation or radio screen is blank or flashes on and off, no sound from speakers, and rear DVD screen inoperative. Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be Set. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Bulletin has been Revised to add the 2017 Colorado, Cruze, Canyon, Chevrolet & GMC Light/Medium Duty Trucks. Please discard Corporate Bulletin Number 03-06-04-071I Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GM?S POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA. Read More »
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores Read More »
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not. Read More »
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only) Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon and a Diagnostic Trouble Code P0011. Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada). Read More »
This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification. Read More »
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada). Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Read More »
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Read More »
This Preliminary Information communication advises the technician of additional steps for diagnosing General Motors high speed local area network. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This technical bulletin provides repair information to correct customer concerns of loss of high speed GMLAN communications, intermittent no crank, IP gauge fluctuation, intermittent door lock cycling /chime operation, various IP warning ... Read More »
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement. Read More »
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only). Read More »
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS). Read More »
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only). Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled ... Read More »
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This informational bulletin is a revision of 10-06-01-008I to add the 2010-2012 Chevrolet Colorado and GMC Canyon, RPO LH9 and update the Labor Operation to the Global Labor Code (GLC). Read More »
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS). Read More »
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, ... Read More »
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm. Read More »
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Read More »
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist ... Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done. Read More »
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only) Read More »
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only) Read More »
This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange Read More »
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks Read More »
This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This Preliminary Information communication provides information to the technician about vehicles that engine runs and idles rough. Technician will find P0171 and or P0174. Read More »
This Preliminary Information communication provides information to the technician about vehicles with the inside door panel material appearing to be pulling back from the door panel backing. Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Read More »
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE DRIVE MOTOR GENERATOR CONTROL MODULE AND ACCESSORY POWER MODULE ARE BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. Read More »
This technical bulletin provides a procedure to correct the customers concern to replace the left side valve cover and active fuel management oil deflector to reduce oil consumption. Read More »
This technical bulletin provides a procedure to install a diode on the vehicles that have an aftermarket equipment and air in controlling voltage spikes in the system that cause the engine to run when the key is off or communication ... Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This preliminary bulletin provides a procedure to install a new cabin air filter kit for vehicles that did not have one if the customer whants one installed to fix the concern of dust intruding into cabin interior. Read More »
This technical bulletin provides a procedure to install double sided tape to the windshield molding to correct the customers concern of a tapping or clicking noise at the winshield area. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This preliminary information bulletin provides information on installing new rivets on the accessory tonneu cover to correct a customers comments on the cover seeming loose Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE AN OUTSIDE AIR TEMPERATURE INOPERATIVE. Read More »
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system. Read More »
This technical bulletin provides a procedure to correct a customer concern of reduced heater performance with winter grille cover installed. Read More »
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have reduced air flow from the Heater-Vent-Air Conditioning dash vents. Read More »
This preliminary informational bulletins provides information regarding the release of a new designed HVAC blower motor assembley. The bulletin provides information on how to correctly install the parts to function as intended. Read More »
This preliminary informational bulletins provides information regarding the release of a new designed HVAC blower motor assembley. The bulletin provides information on how to correctly install the parts to function as intended. Read More »
This preliminary informational bulletin provides a procedure to replace the first junction block terminal and other terminals to correct a condition of poor HVAC performance. Read More »
PROCEDURE FOR INSTALLATION OF AN AFTERMARKET TRAILER BRAKE CONTROLLER IN LIEU OF FACTORY INSTALLED INTEGRATED TRAILER BRAKE CONTROLLER. *KB UPDATED 11/02/07. *NJ UPDATED 2/19/08. Read More »
