Technical Service Bulletins (TSBs) for the 2017 Volt are official communications between Chevrolet & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - ... Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT ... Read More »
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS." Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE REAR AXLE ASSEMBLY FOR VEHICLES WITH THE CONDITONS OF A SQUEAK, SQUAWK, CREAK OR POPPING NOISE FROM THE REAR AXLE DUE TO THE AXLES INNER WALLS MAKING CONTACT WITH THE OUTER WALL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This technical bulletin provides a procedure to drill two holes in the rear axle housings to spray lubricant into and then close up with rivets to correct a condition of a rear axle creak noise due to the improper lubrication of some of ... Read More »
This technical bulletin provides a procedure to drill two holes in the rear axle housings to spray lubricant into and then close up with rivets to correct a condition of a rear axle creak noise due to the improper lubrication of some of ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides repair information to correct a customer concern of intermittent click noise at front of vehicle, ABS, Traction Control System (TCS)/Stabilitrak lamps may illuminate intermittently and/or deactivate for ... Read More »
This Preliminary Information communication advises the technician effective February 19, 2016, the following brake components for the Chevrolet Volt and the Chevrolet Malibu Hybrid are being placed on restriction through the Technical ... Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This technical bulletin provides a procedure for replacing the brake pedal push rod retainer due to a noise heard when applying and releasing the brake pedal. Read More »
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE BRAKE PEDAL PUSH ROD RETAINER WITH THE NEW DESIGN PART TO CORRECT A CUSTOMER CONCERN ON A BRAKE PEDAL SQUEAK NOISE HEARD WHEN APPLYING AND RELEASING THE BRAKE PEDAL DUE TO THE ... Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON DRIVING PUSHING ON THE BRAKE AND ACCELERATOR PEDAL AT THE SAME TIME (2 FOOT DRIVING) MAY RESULT IN A MALFUNCTION INDICATOR LAMP AND LOSS OF REGENERATIVE BRAKING. Read More »
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE BRAKE PEDAL PUSH ROD RETAINER WITH THE NEW DESIGN PART TO CORRECT A CUSTOMER CONCERN ON A BRAKE PEDAL SQUEAK NOISE HEARD WHEN APPLYING AND RELEASING THE BRAKE PEDAL CAUSED BY TO ... Read More »
This Preliminary Information communication advises the technician effective February 19, 2016, the following brake components for the Chevrolet Volt are being placed on restriction through the Technical Assistance Center. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Bulletin provides information, tips and graphics regarding specific Hybrid vehicle hydraulic brake system failures, emphasizing disc brake caliper guide pin failures. Read More »
This informational bulletin provides mulitple starting points for concerns related to various hydraulic brake concerns and how to correct the conditions that may be associated with them. Read More »
This technical bulletin provides a procedure to replace the front wheel speed sensors on vehicles with the condtion of ABS Warning Light On, Traction Control System (TCS)/Stabilitrak Light On, Service Brake Assist and Service Stabilitrak ... Read More »
This informational bulletin provides information for dealers/technicians on when vehicle pulls to the left or right when regenerative braking paddle applied, and/or when brake pedal applied. Read More »
This technical bulletin provides a procedure for replacing the brake pedal push rod retainer due to a noise heard when applying and releasing the brake pedal. Read More »
This technical bulletin provides a procedure for replacing the brake pedal push rod retainer due to a noise heard when applying and releasing the brake pedal. Read More »
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT FOR AND REMOVE A TEMPORARY TIE STRAP ON THE BRAKE PEDAL ASSEMBLY TO CORRECT A CUSTOMER CONCERN OF CLICKING NOISE NEAR THE BRAKE PEDAL, HARD BRAKE PEDAL OR BRAKE LIGHT ON DUE TO THE ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN EFFECTIVE FEBRUARY 19, 2016, THE FOLLOWING BRAKE COMPONENTS FOR THE CHEVROLET VOLT AND THE CHEVROLET MALBU HYBRID ARE BEING PLACED ON RESTRICTION THROUGH THE TECHNICAL ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN EFFECTIVE FEBRUARY 19, 2016, THE FOLLOWING BRAKE COMPONENTS FOR THE CHEVROLET VOLT AND THE CHEVROLET MALBU HYBRID ARE BEING PLACED ON RESTRICTION THROUGH THE TECHNICAL ... Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DRUM:WHEEL CYLINDERS
This informational bulletin provides information on the proper ways to remove or replace the key cylinder covers due to some vehicles having the key cylinders hidden during the time of delivery. Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN EFFECTIVE FEBRUARY 19, 2016, THE FOLLOWING BRAKE COMPONENTS FOR THE CHEVROLET VOLT AND THE CHEVROLET MALBU HYBRID ARE BEING PLACED ON RESTRICTION THROUGH THE TECHNICAL ... Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN EFFECTIVE FEBRUARY 19, 2016, THE FOLLOWING BRAKE COMPONENTS FOR THE CHEVROLET VOLT AND THE CHEVROLET MALBU HYBRID ARE BEING PLACED ON RESTRICTION THROUGH THE TECHNICAL ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN EFFECTIVE FEBRUARY 19, 2016, THE FOLLOWING BRAKE COMPONENTS FOR THE CHEVROLET VOLT AND THE CHEVROLET MALBU HYBRID ARE BEING PLACED ON RESTRICTION THROUGH THE TECHNICAL ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on. Read More »
This technical bulletin provides a procedure on checking the fuse and other multiple concerns that could cause the vehicle to loose propulsion and no start conditions usually caused by a fuse not being tightened down properly. Read More »
This Preliminary Information communication advises the technician effective February 19, 2016, the following brake components for the Chevrolet Volt are being placed on restriction through the Technical Assistance Center. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary Information communication provides information to the technician related to utilizing crankcase pressure testing to aid in engine oil leak diagnostics. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. Read More »
This Preliminary information communicates the possibility of the PCV orifice in the valve cover being plugged and causing the check engine lamp to illuminate and set dtc P00C7 and P0106. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have unwanted engine flairs while the vehicle is at steady state speed or while the vehicle is slowing. Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Technical Bulletin provides information to inspect the active shutter wiring harness for any signs of chafing and the shutters for damage to correct an active shutters inoperative and MIL condition. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years. Read More »
This Bulletin provides a reminder to the Service Personnel to refer to Investigate Vehicle History in Global Warranty Management for Campaign 17058 and verify that it has been performed on the vehicle and after that to reprogram the ECM. Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a rattle or pop noise during gas engine start. That if no codes or other symptoms are present, do not attempt repairs at this time. Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a rattle or pop noise during gas engine start. That if no codes or other symptoms are present, do not attempt repairs at this time. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P2097 set as current or history. Read More »
This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary information communicates diagnostic tip information related to P2119. It advises the technician that this code will not illuminate the MIL or cause reduced engine power conditions. Read More »
16185-Customer Satisfaction. On certain vehicles, the high voltage interlock connector behind the high voltage battery disconnect relay fuse block cover may be susceptible to becoming recessed back into the high voltage battery disconnect ... Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
17228 - Customer Satisfaction Program. Certain vehicles, equipped with an automatic transmission (RPO MKV), may exhibit a condition where the driver notices a ?Propulsion Power is Reduced? message in the driver information center. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces. Read More »
This Preliminary Information communication provides information to the technician related to utilizing crankcase pressure testing to aid in engine oil leak diagnostics. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
This Preliminary Information communication provides information to the technician for vehicles that may have a Service Engine Soon lamp and a current or history Diagnostic Trouble Code P0A7F. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE UNWANTED ENGINE FLAIRS WHILE THE VEHICLE IS AT STEADY STATE SPEED OR WHILE THE VEHICLE IS SLOWING. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT HAVE AN OIL LEAK AT THE REAR OF THE ENGINE. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE CABIN FILTER WITH A CARBON CABIN FILTER TO CORRECT A CUSTOMER CONCERN ON AN ENGINE ODOR AND/OR A BURNING SMELL WITHIN THE VEHICLE DUE TO THE INSULATION MATERIAL IN THE ENGINE ... Read More »
GENERAL MOTORS IS CURRENTLY INVESTIGATING THE CONCERN. UNTIL A PERMANENT SOLUTION IS CREATED, CUSTOMERS THAT HAVE CONCERNS ABOUT THE ODOR SHOULD REPLACE THE CABIN FILTER WITH A CARBON CABIN FILTER. Read More »
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE E80 ENGINE CONTROL MODULE PART NUMBERS 12669908 OR 12672502 HAVE BEEN PLACED ON PART RESTRICTION BY GENERAL MOTORS TECHNICAL ASSISTANCE. Read More »
32340B ? SERVICE UPDATE BULLETIN (SERVICE PROCEDURE REVISED). AN ENGINE MISFIRE CONDITION COULD OCCUR ON THESE VEHICLES CAUSING THE CHECK ENGINE/SERVICE ENGINE SOON LIGHT TO ILLUMINATE, A ROUGH OR HIGH IDLE CONDITION, AND DIAGNOSTIC ... Read More »
32340B ? Service Update Bulletin (Service Procedure Revised). An engine misfire condition could occur on these vehicles causing the check engine/service engine soon light to illuminate, a rough or high idle condition, and diagnostic ... Read More »
32340A - SERVICE UPDATE (REVISED TO ADD 2016 MODEL YEAR VEHICLES). AN ENGINE MISFIRE CONDITION COULD OCCUR CAUSING THE CHECK ENGINE/SERVICE ENGINE SOON LIGHT TO ILLUMINATE, A ROUGH OR HIGH IDLE CONDITION, AND DIAGNOSTIC TROUBLE CODE ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides a service procedure to correct customer concerns of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides repair information to correct a customer concern of a Check Engine Light Illuminated, No Start/ No Propulsion, DTC P0A0C. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module restriction through the General Motors Technical Assistance Center has ended. Read More »
This informational bulletin provides the technician of a possible location of the motor mount grounding out due to debris causing the customer concerns. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about the difficulty in detecting internal combustion engine misfires with a fully charged high voltage battery. Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
This Preliminary information communicates the possibility of the timing chain tensioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have no heat in EV electric mode Technician will find a Diagnostic Trouble Code B048E in the Coolant Heater Control Module. Read More »
This technical bulletin provides a procedure on checking the fuse and other multiple concerns that could cause the vehicle to lose propulsion and no start conditions usually caused by a fuse not being tightened down properly. Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT. Read More »
This informational bulletin provides Information on the Use of Stop Leak Additives in the Coolant System and If a dealership or customer installs a stop leak product or any type of additive to the cooling systems the cost to repair the ... Read More »
This service bulletin provides diagnostic information to correct customer concerns of Speed Limited Message or Reduced Propulsion Power Message Displayed on Driver Information Center (DIC) with no DTCs Set. Read More »
This Preliminary Information communication provides information to the technician related to utilizing crankcase pressure testing to aid in engine oil leak diagnostics. Read More »
ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This technical bulletin provides a procedure for checking and testing the cooling system first before replacing the Auxiliary Coolant Pump for a noise. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE HEATER WATER AUXILIARY PUMP HOSE TO CORRECT A CUSTOMER CONCERN OF A COOLANT LEAK, TEMPERATURE LIGHT ON, OR MALFUNCTION INDICATOR LIGHT ILLUMINATED DUE TO THE HOSE RUBBING ... Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated and DTC P0449 Set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0442 set. Read More »
34510 - SERVICE UPDATE BULLETIN. THESE VEHICLES MAY ALLOW UNLOCKING OF THE FUEL DOOR PRIOR TO COMPLETION OF VENTING OF FUEL TANK VAPOR PRESSURE TO THE EVAPORATIVE EMISSIONS CANISTER. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
This Preliminary information communicates the possibility of the PCV orifice in the valve cover being plugged and causing the check engine lamp to illuminate and set dtc P00C7 and P0106. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE AN ENGINE THAT RUNS ROUGH, SHAKE AGGRESSIVELY, SMOKE FROM THE EXHAUST AND/OR KNOCK AT STARTUP. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
This informational bulletin provides information for higher mileage Volts that are having the EGR cooler being plugged not allowing sufficient flow with DTC being set. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0442 set. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary information communicates a posible loss of 12 volt power to the fuel pump drive module. This is to point the dealer at a possible lose terminal in the instrument panel fuse panel Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
Emissions - General Motors has decided to conduct a voluntary emissions recall involving certain 2016-2019 model year Chevrolet Volt vehicles. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a rattle or pop noise during gas engine start. That if no codes or other symptoms are present, do not attempt repairs at this time. Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
This Preliminary information communicates a posible loss of 12 volt power to the fuel pump drive module. This is to point the dealer at a possible lose terminal in the instrument panel fuse panel Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This Preliminary information communicates a posible loss of 12 volt power to the fuel pump drive module. This is to point the dealer at a possible lose terminal in the instrument panel fuse panel Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
17228 - Customer Satisfaction Program. Certain vehicles, equipped with an automatic transmission (RPO MKV), may exhibit a condition where the driver notices a ?Propulsion Power is Reduced? message in the driver information center. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE GROUND CONNECTION ON A FUSE BOX CABLE THAT COULD BE CAUSING A LOSS OF PROPULSION, NO START AND/OR MULTIPLE DTC'S. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This informational bulletin provide a service tip that when servicing the fuel tank and/or replacing the isolator pads, the padding on the new design tank is smaller than the current design and requires the protective caps be installed to ... Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
This Preliminary information communicates That Techline connect is Not supporting the progaming of the T6 PIM / HPCM. and advies them to call Techline. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary information communicates that some on the Transmission were built without a TUN and what the steps are to program the Transmission. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
Customer Satisfaction program - certain vehicles may have a condition related to the high voltage battery which could gradually lose the ability to maintain voltage. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication advises the technician the 5ET50 electric variable automatic transmission assembly and component restriction through the General Motors Technical Assistance Center has ended . Read More »
This Preliminary Information communication advises the technician that the Hybrid Powertrain Control Module 2 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary information communicates Diagnostic information for the Shift to Park message. Engineering is still investigating the root cause. The PI will be updated to a bulletin once the final root is understood. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary Information communication advises the technician the 5ET50 electric variable automatic transmission assembly and component is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician the 5ET50 electric variable automatic transmission assembly and component is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician the 5ET50 electric variable automatic transmission assembly and component is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician that the Hybrid Powertrain Control Module 2 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This Preliminary information communicates to the technician, thatthey may be working onaconcern of a rattle or pop noise during gas engine start. That if no codes or other symptoms are present, do notattempt repairs at this time. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary Information communication advises the technician the 5ET50 electric variable automatic transmission assembly and component is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary information communicates diagnostic tip information related to P2119. It advises the technician that this code will not illuminate the MIL or cause reduced engine power conditions. Read More »
17228 - Customer Satisfaction Program. Certain vehicles, equipped with an automatic transmission (RPO MKV), may exhibit a condition where the driver notices a ?Propulsion Power is Reduced? message in the driver information center. Read More »
16055 Customer Satisfaction Program. Certain vehicles may exhibit a condition where the driver notices a ?Propulsion Power is Reduced? message in the driver information center. Read More »
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty ... Read More »
THIS TECHNICAL BULLETIN PROVIDES THE PROCEDURES TO COMPLETE A TRANSSMISSION ADAPTIVE LEARN ON ALL THE DIFFERENT TYPES OF VEHICLES AND TRANSMISSIONS BASED ON RPO OPTIONS TO CORRECT A CONDITION OF HARSH SHIFTS ON HARD ACCELLERATIONS. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK FOR PROPER SHIFTER KNOB INSTALLATION, ADJUST SHIFT CABLE AND REPLACE SHIFTER IF NECESSARY TO CORRECT A CUSTOMER CONCERN THAT IT IS DIFFICULT TO MOVE THE SHIFTER OUT OF PARK OR INTO ... Read More »
This Preliminary Information communication provides information to the technician for vehicles that may have a Service Engine Soon lamp and a current or history Diagnostic Trouble Code P0A7F. Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This Preliminary information communicates That Techline connect is Not supporting the progaming of the T6 PIM / HPCM. and advies them to call Techline. Read More »
Customer Satisfaction Program. Certain vehicles may have a condition related to the high voltage battery which could gradually lose the ability to maintain voltage. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary information communicates is to commuate teardown finds. As we move away from Transmisison Replacements to internal service. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a rattle or pop noise during gas engine start. That if no codes or other symptoms are present, do not attempt repairs at this time. Read More »
This Preliminary Information communication advises the technician the 5ET50 electric variable automatic transmission assembly and component is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
43940 - SERVICE UPDATE. CERTAIN 2016 MODEL YEAR CHEVROLET MALIBU AND 2016-2017 CHEVROLET VOLT VEHICLES MAY HAVE A CONDITION WHERE A BURR MAY BE PRESENT ON THE SPRING END WHICH IS PART OF THE SHIFTER ASSEMBLY. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE DRIVE MOTOR GENERATOR CONTROL MODULE IS BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. Read More »
34510 - Service Update Bulletin. These vehicles may allow unlocking of the fuel door prior to completion of venting of fuel tank vapor pressure to the evaporative emissions canister. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE 5ET50 ELECTRIC VARIABLE AUTOMATIC TRANSMISSION ASSEMBLY AND COMPONENT IS BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Preliminary Information communication advises the technician that the Hybrid Powertrain Control Module 2 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides the technician with inspection and repair instructions for vehicles with a no start/no propulsion condition that is setting a DTC P0A0C for the high voltage interlock circuit. Read More »
This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request. Read More »
34510 - Service Update Bulletin. These vehicles may allow unlocking of the fuel door prior to completion of venting of fuel tank vapor pressure to the evaporative emissions canister. Read More »
This Preliminary Information communication advises the technician if a vehicle has a Service Engine Soon lamp with Diagnostic Trouble Code P0AE3 current or history. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
Squeak, Squawk, Creak or Popping Noise Originating from Rear Axle Some customers may comment on a squeak, squawk, creak or popping noise in the rear of the vehicle when cornering or pulling into driveways. Read More »
Special Coverage. On some vehicles, a malfunction involving the battery energy control module (BECM) may cause a reduced power mode, a no start condition, or a no charge condition. Dealers are to replace the battery energy control module. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
Special Coverage. On some vehicles, a malfunction involving the battery energy control module (BECM) may cause a reduced power mode, a no start condition, or a no charge condition. Dealers are to replace the battery energy control module. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary information communicates a posible loss of 12 volt power to the fuel pump drive module. This is to point the dealer at a possible lose terminal in the instrument panel fuse panel Read More »
This service bulletin provides a procedure to install a battery energy control module to correct customer concerns of No Start or MIL Illuminated with DTCs. Read More »
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States. Read More »
This Preliminary information communicates That Techline connect is Not supporting the progaming of the T6 PIM / HPCM. and advies them to call Techline. Read More »
This service bulletin provides diagnostic information to correct customer concerns of Speed Limited Message or Reduced Propulsion Power Message Displayed on Driver Information Center (DIC) with no DTCs Set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
Customer Satisfaction program - certain vehicles may have a condition related to the high voltage battery which could gradually lose the ability to maintain voltage. Read More »
Customer Satisfaction program - certain vehicles may have a condition related to the high voltage battery which could gradually lose the ability to maintain voltage. Read More »
Customer Satisfaction Program. Certain vehicles may have a condition related to the high voltage battery which could gradually lose the ability to maintain voltage. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This Bulletin provides a Service Procedure to correct a condition where the 120V Portable Charge Cord is Inoperative or Charges Intermittently. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communication advises the technician on a area to look at for a loss of low speed lan communication if the concern can't be found through normal diagnosis. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vehicles EV range is less than expected, or the estimated EV range on the display is greater than the actual range achieved. Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com. or http://www.nfpa. Read More »
This Preliminary Information communication provides information to the technician about vehicles equipped with absorbent glass mat 12 volt battery. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communication advises the technician the Battery Charge Module restriction through the General Motors Technical Assistance Center has ended. Read More »
This Preliminary Information communication advises the technician that the accessory power module is being placed on part restriction. Dealer will need to call General Motors Technical Assistance Center for part replacement authorization. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles EV range is less than expected, or the estimated EV range on the display is greater than the actual range achieved. Read More »
This Preliminary information communicates more information to help diagnose P1AEE and P1AEF. It Gives 3 possible reason for the codes to set and areas to look. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery has been placed on part restriction by General Motors Technical Assistance. Read More »
This technical bulletin provides a procedure to replace the GEN I charging system with a GEN II charging system only if vehicles apply within the settings. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician for balancing a hybrid battery pack after replacing a battery section. Certain unlisted codes may be experienced when using the battery service tool EL50332. Read More »
This Preliminary information communicates Diagnostic information for the Shift to Park message. Engineering is still investigating the root cause. The PI will be updated to a bulletin once the final root is understood. Read More »
This Bulletin provides information to diagnose a MIL Illuminated and/or a No Start condition caused by the Battery Sections 1, 2 or 3 with a total possibility of 96 separate DTCs being set depending on the Cells involved. Read More »
This Preliminary Information communication provides information to the technician about vehicles EV range is less than expected, or the estimated EV range on the display is greater than the actual range achieved. Read More »
This Preliminary Information communication advises the technician the Battery Charge Module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician on the steps to diagnose the concern and the steps to repair the concern. Customer states that they are unable to select delayed or delayed/rate based charging. Read More »
This Preliminary Information communication advises the technician that the accessory power module is being placed on part restriction. Dealer will need to call General Motors Technical Assistance Center for part replacement authorization. Read More »
This Preliminary Information communication advises the technician the Battery Charge Module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician the 5ET50 electric variable automatic transmission assembly and component is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication advises the technician that the Cabin Heater Control Module part number 22816851 and 84351883 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar? Module Functionality After OnStar Module Replacement for Another Condition. Read More »
This Technical Bulletin provides information to inspect the active shutter wiring harness for any signs of chafing and the shutters for damage to correct an active shutters inoperative and MIL condition. Read More »
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu. Read More »
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated and DTC P0449 Set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary Information communication advises the technician that the accessory power module is being placed on part restriction. Dealer will need to call General Motors Technical Assistance Center for part replacement authorization. Read More »
This Preliminary Information communication advises the technician that the Cabin Heater Control Module part number 22816851 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language. Read More »
This Preliminary information communicates to the technician steps to address the MIL concern on the listed vehicles. It advises that if the vehicle has the code stored, clear it and retest to see if it returns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary information communicates a posible loss of 12 volt power to the fuel pump drive module. This is to point the dealer at a possible lose terminal in the instrument panel fuse panel Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
Intermittent Operation of Key Fobs, Door Unlock Inoperative ?No Remote Detected? Message with Possible TPM MIL Some customers may comment on intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P2097 set as current or history. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
16185-Customer Satisfaction. On certain vehicles, the high voltage interlock connector behind the high voltage battery disconnect relay fuse block cover may be susceptible to becoming recessed back into the high voltage battery disconnect ... Read More »
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Read More »
17228 - Customer Satisfaction Program. Certain vehicles, equipped with an automatic transmission (RPO MKV), may exhibit a condition where the driver notices a ?Propulsion Power is Reduced? message in the driver information center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when watching a movie the audio does not match the video when playing though the vehicles speakers. Read More »
This Preliminary information communicates a posible loss of 12 volt power to the fuel pump drive module. This is to point the dealer at a possible lose terminal in the instrument panel fuse panel Read More »
This Preliminary Information communication advises the technician that the Cabin Heater Control Module part number 22816851 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have no heat in EV electric mode Technician will find a Diagnostic Trouble Code B048E in the Coolant Heater Control Module. Read More »
This Preliminary Information communicationends thewireless charging module restriction through the General Motors Technical Assistance Center. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
This Preliminary Information communication provides information to the technician for vehicles that may have a Service Engine Soon lamp and a current or history Diagnostic Trouble Code P0A7F. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface ... Read More »
This technical bulletin provides a procedure to aid in diagnosing the DTCs set and reprogram the DMPI module to correct the customers concern. Read More »
16055 Customer Satisfaction Program. Certain vehicles may exhibit a condition where the driver notices a ?Propulsion Power is Reduced? message in the driver information center. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Read More »
This technical bulletin provides a procedure on checking the fuse and other multiple concerns that could cause the vehicle to lose propulsion and no start conditions usually caused by a fuse not being tightened down properly. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P2097 set as current or history. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This technical bulletin provides a procedure on checking the fuse and other multiple concerns that could cause the vehicle to loose propulsion and no start conditions usually caused by a fuse not being tightened down properly. Read More »
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATES THAT WHEN CUSTOMER OR TECHNICIAN MAY INDICATE WHEN ATTEMPTING TO ADD A NEW TRANSMITTER TO A VEHICLE FOLLOWING THE ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM PROCEDURE. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INSPECTION AND REPAIR INSTRUCTIONS FOR VEHICLES WITH A NO START OR NO PROPULSION CONDITION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN FOR VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON LAMP AND A CURRENT OR HISTORY DIAGNOSTIC TROUBLE CODE P0A7F. Read More »
This engineering information bulletin is requesting information from the dealers on a customer concern that one of the USB ports is not charging, allowing data to transfer. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE IDENTIFICATION OF VEHICLES THAT ARE SHIPPED WITH THE TRANSPORT MODE ON AND HOW TO TURN IT OFF. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO USE SERVICE PROGRAMMING SYSTEM AND REPROGRAM HYBRID POWERTRAIN CONTROL MODULE 2 FOR A SERVICE ENGINE SOON LIGHT ON THE GAUGE CLUSTER WITH A DIAGNOSTIC TROUBLE CODE OF ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This Preliminary Information communication advises the technician when using perpendicular parking the left side of the vehicle may come too close to a parked vehicle on the first pass. Read More »
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications Read More »
This technical bulletin provides a procedure to replace the front wheel speed sensors on vehicles with the condtion of ABS Warning Light On, Traction Control System (TCS)/Stabilitrak Light On, Service Brake Assist and Service Stabilitrak ... Read More »
This Preliminary Information communication advises the technician if blown or open fuses are found in the High Voltage Battery Disconnect Relay assembly the fuses are not available from General Motors Service Parts Operations. Read More »
This Preliminary Information communication advises the technician effective February 19, 2016, the following brake components for the Chevrolet Volt are being placed on restriction through the Technical Assistance Center. Read More »
This informational bulletin provides information on Phantom Three Beeps or Horn Chirps Heard After Turning Off Vehicle and that it should be considered normal. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO RE-POSITION THE FRONT WIRING HARNESS AWAY FROM THE HORN TO CORRECT HORNS THAT ARE PERFORMING POORLY CAUSED BY THE WIRING HARNESS RESTING AGAINST THE HORN AND BRACKET ASSEMBLY CAUSING THEM ... Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have the high voltage battery the tabs on X3 could become damaged during service. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off. Read More »
This Bulletin provides information to diagnose a MIL Illuminated and/or a No Start condition caused by the Battery Sections 1, 2 or 3 with a total possibility of 96 separate DTCs being set depending on the Cells involved. Read More »
This Preliminary information communicates more information to help diagnoseP1AEE and P1AEF. It Gives 3 possible reason for the codes to set and areas to look. Read More »
This Preliminary Information communication advises the technician the Battery Charge Module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery hasbeen placed on part restriction by General Motors Technical Assistance. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
This Preliminary Information communication advises the technician the Battery Charge Module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
This Preliminary Information communication provides information for the technician to check for an open 15 Amp fuse in the High Voltage Battery Disconnect Relay Assembly when the vehicle is unable to charge a 12 volt or High Voltage ... Read More »
This Preliminary Information communication advises the technician if blown or open fuses are found in the High Voltage Battery Disconnect Relay assembly the fuses are not available from General Motors Service Parts Operations. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
This Preliminary Information communication provides information to the technician about vehicles EV range is less than expected, or the estimated EV range on the display is greater than the actual range achieved. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
16017 - Service Update. The battery positive cable terminal is misaligned to the auxiliary under hood fuse block preventing the terminal from being fully seated on the block. A loose connection may result in electrical arcing. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INSPECTION AND REPAIR INSTRUCTIONS FOR VEHICLES WITH A NO START OR NO PROPULSION CONDITION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HIGH VOLTAGE DRIVE MOTOR BATTERY AND BATTERY SECTIONS HAVE BEEN PLACED ON PART RESTRICTION BY GENERAL MOTORS TECHNICAL ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION FOR THE TECHNICIAN TO CHECK FOR AN OPEN 15 AMP FUSE IN THE HIGH VOLTAGE BATTERY DISCONNECT RELAY ASSEMBLY WHEN THE VEHICLE IS UNABLE TO CHARGE A 12 VOLT OR HIGH VOLTAGE ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT SOME OF THE REPLACEMENT FUSES CAN BE OBTAINED FROM THE WARRANTY PARTS CENTER (WPC) EXCEPT THE 15A FUSE-OBCM FUSE WHICH CAN BE OBTAINED FROM GENERAL MOTOR SERVICE PARTS ... Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY. Read More »
This Preliminary Information communication advises the technician that the high voltage drive motor battery and battery sections are being placed on restriction through the General Motors Technical Assistance Center. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE BATTERY CHARGE MODULE IS BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. Read More »
This Preliminary information communicates that the New battery section as a broken wiring harness clip, and to use a Velcor strip to hold the harness in place. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This Technical Bulletin provides information to inspect the active shutter wiring harness for any signs of chafing and the shutters for damage to correct an active shutters inoperative and MIL condition. Read More »
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information. Read More »
This technical bulletin provides a procedure to re-secure the horn wiring harness to correct a condition of poor horn performance, muffled and or not loud Read More »
ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE GROUND CONNECTION ON A FUSE BOX CABLE THAT COULD BE CAUSING A LOSS OF PROPULSION, NO START AND/OR MULTIPLE DTC'S. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT SOME OF THE REPLACEMENT FUSES CAN BE OBTAINED FROM THE WARRANTY PARTS CENTER (WPC) EXCEPT THE 15A FUSE-OBCM FUSE WHICH CAN BE OBTAINED FROM GENERAL MOTOR SERVICE PARTS ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
All or Some Options May Be Missing from Driver Information Center (DIC) ?Info Pages? Menu Due to Them Not Being Selected Condition Some customers may comment that with the ?Info? option selected from the main menu (1), the ?Info ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This technical bulletin provides a procedure on how to take the vehicles out of transport mode for vehicles with the condition of Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is ... Read More »
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Read More »
This Bulletin provides a reminder to the Service Personnel to refer to Investigate Vehicle History in Global Warranty Management for Campaign 17058 and verify that it has been performed on the vehicle and after that to reprogram the ECM. Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary information communicates more information to help diagnoseP1AEE and P1AEF. It Gives 3 possible reason for the codes to set and areas to look. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use. Read More »
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communication advises the technician that the Hybrid Powertrain Control Module 2 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communicationends thewireless charging module restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P2097 set as current or history. Read More »
39570 - SUB - The image processor within the front camera module (FCM) may reset and be offline for 25-35 seconds. During this period, features reliant upon the camera information will respond to the last known data for 25-35 sec. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication advises the technician that the E80 Engine Control Module part numbers 12669908 or 12672502 have been placed on part restriction by General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This informational bulletin provides information on GM offering the Android Auto feature upgrade for 2016 and 2017 model year vehicles and how to proceed with reprogramming the vehicles to include this application for use. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT ADDING TRANSMITTERS WITHOUT USING SERVICE PROGRAMMING SYSTEM. VERIFY ALL MECHANICAL KEYS OPERATE CORRECTLY BEFORE BEGINNING ANY PROGRAMMING PROCEDURES. Read More »
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2. Read More »
32340B ? Service Update Bulletin (Service Procedure Revised). An engine misfire condition could occur on these vehicles causing the check engine/service engine soon light to illuminate, a rough or high idle condition, and diagnostic ... Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
32340A - SERVICE UPDATE (REVISED TO ADD 2016 MODEL YEAR VEHICLES). AN ENGINE MISFIRE CONDITION COULD OCCUR CAUSING THE CHECK ENGINE/SERVICE ENGINE SOON LIGHT TO ILLUMINATE, A ROUGH OR HIGH IDLE CONDITION, AND DIAGNOSTIC TROUBLE CODE ... Read More »
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ... Read More »
This Preliminary Information communication provides information to the technician about vehicles EV range is less than expected, or the estimated EV range on the display is greater than the actual range achieved. Read More »
16055 Customer Satisfaction Program. Certain vehicles may exhibit a condition where the driver notices a ?Propulsion Power is Reduced? message in the driver information center. Read More »
This Preliminary information communicates That Techline connect is Not supporting the progaming of the T6 PIM / HPCM. and advies them to call Techline. Read More »
120V Portable Charge Cord is Inoperative or Charges Vehicle Intermittently Condition Some customers may comment that the 120V portable charge cord does not work or that the vehicle does not charge completely or may charge intermittently. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
Emissions - General Motors has decided to conduct a voluntary emissions recall involving certain 2016-2019 model year Chevrolet Volt vehicles. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON EXTERIOR LIGHTING COMPONENTS THAT HAVE BEEN TINTED OR SMOKED BY AN OUTSIDE VENDOR AND GENERAL MOTORS POSITION ON ALTERING THESE COMPONENTS. Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This informational bulletin provides information on wiper arms that have a pedestrian protection system and the potential for the system to be inadvertently tripped. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides repair information to correct a customer concern of a Check Engine Light Illuminated, No Start/ No Propulsion, DTC P0A0C. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON LOCATING AND RECONNECTING AIRBAG CONNECTORS THAT ARE NOT FULLY SEATED TO CORRECT A CUSTOMER CONCERN OF AN AIRBAG WARNING LAMP ILLUMINATED, OR ONE, OR MORE, AIRBAG DTC(S) SET. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This Preliminary Information communication advises the technician on cardboard shell that is found in the vehicle during Pre-Delivery Inspection. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON THE PROPER WASHING OF THE BRIGHT ALUMINUM MOLDINGS TO AVOID THE MOLDINGS FROM GETTING DAMAGED. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON A FOAM AND CARDBOARD SHELL THAT IS FOUND IN THE VEHICLE DURING PRE-DELIVERY INSPECTION. Read More »
This technical bulletin provides a procedure to Install Foam Between Charge Port Housing and Door Switch Retaining Tang to correct a conditon of CHARGE DOOR OPEN Message Displayed with Charge Port Door ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON A FOAM AND CARDBOARD SHELL THAT IS FOUND IN THE VEHICLE DURING PRE-DELIVERY INSPECTION. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE FRONT FUEL FEED HOSE TO CORRECT A CUSTOMER CONCERN ON SMELLING FUEL OR AN ODOR COMING IN THROUGH THE VENTS WHILE THE ENGINE IS RUNNING DUE TO FUEL VAPOR ESCAPING FROM THE FRONT ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This informational bulletin provides information for technicians that upon removal of a front door trim panel, two high retention retainers will break but must be replaced with same high retention retainers to properly secure the door trim. Read More »
THIS TECHNICAL PROVIDES A PROCEDURE TO CHECK THE REAR DOORS FOR LOOSE OR OVER TIGHTENED CABLES THAT MAY CAUSE THE CUSTOMERS CONCERN OF THE REAR DOORS WONT OPEN. Read More »
This informational bulletin provides information for technicians that upon removal of a front door trim panel, two high retention retainers will break but must be replaced with same high retention retainers to properly secure the door trim. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON A FOAM AND CARDBOARD SHELL THAT IS FOUND IN THE VEHICLE DURING PRE-DELIVERY INSPECTION. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON DRIVING PUSHING ON THE BRAKE AND ACCELERATOR PEDAL AT THE SAME TIME (2 FOOT DRIVING) MAY RESULT IN A MALFUNCTION INDICATOR LAMP AND LOSS OF REGENERATIVE BRAKING. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This informational bulletin provides information for dealers/technicians on when vehicle pulls to the left or right when regenerative braking paddle applied, and/or when brake pedal applied. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
18016 - Service Update. Certain vehicles may have been built and shipped without the tire repair sealant or other components from the tire inflator kit. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects ... Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This informational bulletin provides information for dealers/technicians on when vehicle pulls to the left or right when regenerative braking paddle applied, and/or when brake pedal applied. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides information that the TPM sensors must always be relearned when accessory wheels are installed on the vehicle. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO WHAT FREQUENCY TIRE PRESSURE INDICATOR SENSOR SHOULD BE INSTALLED ON THE CAR FOR ACCESSORY WHEELS TO CORRECT A CONCERN THAT THE TIRE PRESSURE INDICATOR SENSOR TOOL WILL READ THE SENSOR BUT ... Read More »
This Preliminary Information communication advises the technician what affects electric range and provides driving tips for better energy efficiency. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided. Read More »
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels. Read More »
This technical bulletin provides a procedure to drill two holes in the rear axle housings to spray lubricant into and then close up with rivets to correct a condition of a rear axle creak noise due to the improper lubrication of some of ... Read More »
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - ... Read More »
This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Read More »
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes. Read More »
This technical bulletin provides a procedure to replace the front wheel speed sensors on vehicles with the condtion of ABS Warning Light On, Traction Control System (TCS)/Stabilitrak Light On, Service Brake Assist and Service Stabilitrak ... Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This technical bulletin provides a procedure to disengage the jammed parts and release the gears for proper function caused by the mechanical of the height adjustment being jammed, not broken creating a condition of difficult to adjust ... Read More »
This technical bulletin provides a procedure to disengage the jammed parts and release the gears for proper function caused by the mechanical of the height adjustment being jammed, not broken creating a condition of difficult to adjust ... Read More »
This technical bulletin provides repair information to correct a customer concern of intermittent click noise at front of vehicle, ABS, Traction Control System (TCS)/Stabilitrak lamps may illuminate intermittently and/or deactivate for ... Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician for balancing a hybrid battery pack after replacing a battery section. Certain unlisted codes may be experienced when using the battery service tool EL50332. Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert". Read More »
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert". Read More »
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert". Read More »
Customer Satisfaction program - certain vehicles may have a condition related to the high voltage battery which could gradually lose the ability to maintain voltage. Read More »
Customer Satisfaction program - certain vehicles may have a condition related to the high voltage battery which could gradually lose the ability to maintain voltage. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication advises the technician when using perpendicular parking the left side of the vehicle may come too close to a parked vehicle on the first pass. Read More »
Emissions - General Motors has decided to conduct a voluntary emissions recall involving certain 2016-2019 model year Chevrolet Volt vehicles. Read More »
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. Read More »
This Preliminary Information communication provides information to the technician about vehicles with an intermittent loss of gridlines in the rear camera display screen and a "Service Rear Vision System" message that both happen at the ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES WITH AN INTERMITTENT LOSS OF GRIDLINES IN THE REAR CAMERA DISPLAY SCREEN AND A "SERVICE REAR VISION SYSTEM" MESSAGE THAT BOTH HAPPEN AT THE ... Read More »
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates That Techline connect is Not supporting the progaming of the T6 PIM / HPCM. and advies them to call Techline. Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This Bulletin provides a Service Procedure to correct a condition where the 120V Portable Charge Cord is Inoperative or Charges Intermittently. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This technical bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Read More »
This informational bulletin provides the technician of a possible location of the motor mount grounding out due to debris causing the customer concerns. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary Information communication advises the technician on cardboard shell that is found in the vehicle during Pre-Delivery Inspection. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This Preliminary Information communication advises the technician effective February 19, 2016, the following brake components for the Chevrolet Volt and the Chevrolet Malibu Hybrid are being placed on restriction through the Technical ... Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
Intermittent Operation of Key Fobs, Door Unlock Inoperative ?No Remote Detected? Message with Possible TPM MIL Some customers may comment on intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary information communicates the possibility of the timing chain tensioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
16185-Customer Satisfaction. On certain vehicles, the high voltage interlock connector behind the high voltage battery disconnect relay fuse block cover may be susceptible to becoming recessed back into the high voltage battery disconnect ... Read More »
This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This Preliminary information communicates a posible loss of 12 volt power to the fuel pump drive module. This is to point the dealer at a possible lose terminal in the instrument panel fuse panel Read More »
This Preliminary Information communication advises the technician that the Cabin Heater Control Module part number 22816851 will be placed on a parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have no heat in EV electric mode Technician will find a Diagnostic Trouble Code B048E in the Coolant Heater Control Module. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON THE TIRES SUPPLIED WITH A NEW VEHICLE ARE COVERED BY GENERAL MOTORS AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP UNDER THE BUMPER-TO-BUMPER NEW VEHICLE LIMITED WARRANTY. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL ... Read More »
THIS TECHNICAL PROVIDES A PROCEDURE TO CHECK THE REAR DOORS FOR LOOSE OR OVER TIGHTENED CABLES THAT MAY CAUSE THE CUSTOMERS CONCERN OF THE REAR DOORS WONT OPEN. Read More »
THIS ENGINEERING INFORMATIONAL BULLETIN IS ENDING THE NEED FOR INFORMATION FROM THE FIELD OF VEHICLES WITH THE CONDITION OF USB PORT INOPERATIVE. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON DRIVING PUSHING ON THE BRAKE AND ACCELERATOR PEDAL AT THE SAME TIME (2 FOOT DRIVING) MAY RESULT IN A MALFUNCTION INDICATOR LAMP AND LOSS OF REGENERATIVE BRAKING. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE DRIVE MOTOR GENERATOR CONTROL MODULE IS BEING PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT ADDING TRANSMITTERS WITHOUT USING SERVICE PROGRAMMING SYSTEM. VERIFY ALL MECHANICAL KEYS OPERATE CORRECTLY BEFORE BEGINNING ANY PROGRAMMING PROCEDURES. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON THE PROPER WASHING OF THE BRIGHT ALUMINUM MOLDINGS TO AVOID THE MOLDINGS FROM GETTING DAMAGED. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH A DIAGNOSTIC AID FOR IDENTIFYING INFOTAINMENT COMPONENTS ON THE VEHICLES TO ENSURE THAT THE CORRECT COMPONENT IS ORDERED OR REPLACED AND THE CORRECT LABOR CODE IS ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE 120 VOLT CHARGE CORD FOR THE VEHICLE HAS BEEN PLACED ON PART RESTRICTION BY GENERAL MOTORS TECHNICAL ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE UPPER AND LOWER OIL PAN WILL BE PLACED ON PRODUCT QUALITY CENTER PART RESTRICTION. DEALER WILL NEED TO CALL GENERAL MOTORS PRODUCT QUALITY CENTER FOR ASSISTANCE. Read More »
This warranty administration bulletin provides information on GM?s policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND CORRECT THE CONCERN OF A CUSTOMER THAT STATES THAT THEY ARE UNABLE TO SELECT DELAYED OR DELAYED/RATE BASED CHARGING. Read More »
34510 - SERVICE UPDATE BULLETIN. THESE VEHICLES MAY ALLOW UNLOCKING OF THE FUEL DOOR PRIOR TO COMPLETION OF VENTING OF FUEL TANK VAPOR PRESSURE TO THE EVAPORATIVE EMISSIONS CANISTER. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON A FOAM AND CARDBOARD SHELL THAT IS FOUND IN THE VEHICLE DURING PRE-DELIVERY INSPECTION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This service bulletin provides information on Forklift and Vehicle Hoist Requirements to Support Electric Vehicle (EV) High Voltage Battery Handling. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport ... Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This informational bulletin provides information on Phantom Three Beeps or Horn Chirps Heard After Turning Off Vehicle and that it should be considered normal. Read More »
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4). Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Read More »
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis. Read More »
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary information communicates to the technician, that if the latest calibration have been installed per 17058 and Service Information for the P2097 fails to isolate the cause, do not attempt repairs at this time. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This informational bulletin provides information on GM offering the Android Auto feature upgrade for 2016 and 2017 model year vehicles and how to proceed with reprogramming the vehicles to include this application for use. Read More »
This informational bulletin provides information for technicians to clear codes and for dealership personnel to advise the customers to avoid resting their foot on the brake pedal while using the accelerator pedal. Read More »
17058 - Service Update. The post O2 trim diagnostic may falsely fail causing DTC P2097 to set, commanding a Malfunction Indicator Light (MIL) to illuminate. The vehicle runs and functions as normal with no other symptoms. Read More »
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Read More »
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4). Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN EFFECTIVE FEBRUARY 19, 2016, THE FOLLOWING BRAKE COMPONENTS FOR THE CHEVROLET VOLT AND THE CHEVROLET MALBU HYBRID ARE BEING PLACED ON RESTRICTION THROUGH THE TECHNICAL ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO ENABLE THE 4G LTE WIFI ON NEWLY DELIVERED VEHICLES FOR SOME VEHICLES THAT WERE NOT SHIPPED WITH THE FEATURE NOT ENABLED. Read More »
THIS TECHNICAL BULLETIN PROVIDES DIAGNOSTIC TIPS TO HELP CORRECT MULTIPLE CONCERNS REGARDING THE USB PORT BEING INOPERATIVE OR UNABLE TO PLAY MUSIC THROUGH THE USB PORT. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND CORRECT THE CONCERN OF A CUSTOMER THAT STATES THAT THEY ARE UNABLE TO SELECT DELAYED OR DELAYED/RATE BASED CHARGING. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE. Read More »
This Preliminary Information communication advises the technician what affects electric range and provides driving tips for better energy efficiency. Read More »
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near Read More »
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ... Read More »
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits. Read More »
This informational bulletin provides information on the proper ways to remove or replace the key cylinder covers due to somevehicleshavingthe key cylinders hidden during the time of delivery. Read More »
This Technical bulletin provides a procedure to replace the radio to correct radio personalization settings on the infotainment display and a blank HVAC pop-up selecting HVAC Control settings. Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This informational bulletin provides information on GM offering the Android Auto feature upgrade for 2016 and 2017 model year vehicles and how to proceed with reprogramming the vehicles to include this application for use. Read More »
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Read More »
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
This Preliminary Information communication provides the technician with information on vehicles with navigation radio Regular Production Option Code IO6 or UY4 that defaults to West Virginia instead of Virginia on a manual entry. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Read More »
This Preliminary Information communication provides the technician with information on vehicles with navigation radio Regular Production Option Code IO6 or UY4 that defaults to West Virginia instead of Virginia on a manual entry. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A BLANK RADIO DISPLAY. DEALER SHOULD ADVISE THE CUSTOMER GENERAL MOTORS IS WORKING ON A SOLUTION TO THE CONCERN. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER, RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Read More »
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of ... Read More »
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Read More »
This Preliminary Information communication provides the technician with information on vehicles with navigation radio Regular Production Option Code IO6 or UY4 that defaults to West Virginia instead of Virginia on a manual entry. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON VEHICLES WITH NAVIGATION RADIO REGULAR PRODUCTION OPTION CODE IO6 OR UY4 THAT DEFAULTS TO WEST VIRGINIA INSTEAD OF VIRGINIA ON A MANUAL ENTRY. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE HMI MODULE TO CORRECT A CONDITION OF GPS INOPERATIVE, RED LINE ACROSS GPS INDICATOR OR THE LOCATION IS STUCK IN WARREN MICHIGAN. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin provides a procedure to disengage the jammed parts and release the gears for proper function caused by the mechanical of the height adjustment being jammed, not broken creating a condition of difficult to adjust ... Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information for dealers/technicians on when vehicle pulls to the left or right when regenerative braking paddle applied, and/or when brake pedal applied. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months). Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication advises the technician that the High Voltage Drive Motor Battery and Battery sections have been placed on part restriction by General Motors Technical Assistance. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary information communicates to dealers on how to diagnose and repair the vehicle if it setsDiagnostic trouble codes P0AC4 (ECM) and P2797 (HPCM) Read More »
This Preliminary information communicates more information to help diagnoseP1AEE and P1AEF. It Gives 3 possible reason for the codes to set and areas to look. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
17058 - Service Update. The post O2 trim diagnostic may falsely fail causing DTC P2097 to set, commanding a Malfunction Indicator Light (MIL) to illuminate. The vehicle runs and functions as normal with no other symptoms. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE ACCESSORY POWER MODULE IS BEING PLACED ON PART RESTRICTION. DEALER WILL NEED TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR PART REPLACEMENT AUTHORIZATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE PART RESTRICTION FOR THE GEN 2 CHARGE CORD, PART NUMBERS 24277224 HAS ENDED. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA. Read More »
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO USE SERVICE PROGRAMMING SYSTEM AND REPROGRAM HYBRID POWERTRAIN CONTROL MODULE 2 FOR A SERVICE ENGINE SOON LIGHT ON THE GAUGE CLUSTER WITH A DIAGNOSTIC TROUBLE CODE OF ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO WHAT FREQUENCY TIRE PRESSURE INDICATOR SENSOR SHOULD BE INSTALLED ON THE CAR FOR ACCESSORY WHEELS TO CORRECT A CONCERN THAT THE TIRE PRESSURE INDICATOR SENSOR TOOL WILL READ THE SENSOR BUT ... Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GM?S POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA. Read More »
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. Read More »
This Preliminary Information communication advises the technician what affects electric range and provides driving tips for better energy efficiency. Read More »
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores Read More »
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not. Read More »
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Bulletin provides a Service Procedure to correct a condition where the 120V Portable Charge Cord is Inoperative or Charges Intermittently. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin provides the technician of a possible location of the motor mount grounding out due to debris causing the customer concerns. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
Intermittent Operation of Key Fobs, Door Unlock Inoperative ?No Remote Detected? Message with Possible TPM MIL Some customers may comment on intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a rattle or pop noise during gas engine start. That if no codes or other symptoms are present, do not attempt repairs at this time. Read More »
This Preliminary information communicates the possibility of the timing chain tensioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This informational bulletin provide a service tip that when servicing the fuel tank and/or replacing the isolator pads, the padding on the new design tank is smaller than the current design and requires the protective caps be installed to ... Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin provides a procedure to drill two holes in the rear axle housings to spray lubricant into and then close up with rivets to correct a condition of a rear axle creak noise due to the improper lubrication of some of ... Read More »
This Preliminary Information communication advises the technician that the accessory power module is being placed on part restriction. Dealer will need to call General Motors Technical Assistance Center for part replacement authorization. Read More »
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits. Read More »
This Preliminary Information communication provides information to the technician about vehicles with an intermittent loss of gridlines in the rear camera display screen and a "Service Rear Vision System" message that both happen at the ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Read More »
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH A DIAGNOSTIC AID FOR IDENTIFYING INFOTAINMENT COMPONENTS ON THE VEHICLES TO ENSURE THAT THE CORRECT COMPONENT IS ORDERED OR REPLACED AND THE CORRECT LABOR CODE IS ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE UPPER AND LOWER OIL PAN WILL BE PLACED ON PRODUCT QUALITY CENTER PART RESTRICTION. DEALER WILL NEED TO CALL GENERAL MOTORS PRODUCT QUALITY CENTER FOR ASSISTANCE. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO WHAT FREQUENCY TIRE PRESSURE INDICATOR SENSOR SHOULD BE INSTALLED ON THE CAR FOR ACCESSORY WHEELS TO CORRECT A CONCERN THAT THE TIRE PRESSURE INDICATOR SENSOR TOOL WILL READ THE SENSOR BUT ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Technical bulletin provides a procedure to replace the radio to correct radio personalization settings on the infotainment display and a blank HVAC pop-up selecting HVAC Control settings. Read More »
This Preliminary Information communication advises the technician that the Cabin Heater Control Module part number 22816851 and 84351883 will be placed on a fff parts restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
THIS TECHNICIAL BULLETIN PROVIDES INFORMATION ON TESTING THE ACCM DUE TO SMALL AMOUNT OF OIL WEEPING INCLUDING THE CORRECT CLEANERS TO USE FOR THE OIL/DYE. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
