Technical Service Bulletins (TSBs) for the 2018 i3 are official communications between BMW & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
STEERING ASSISTANCE SPORADIC REDUCTION: The driver notices a reduction of steering assistance sporadically while in certain driving situations. Steering control is never lost when the reduction of assistance occurs. Read More »
?SPORADIC REDUCTION OF STEERING ASSISTANCE: The driver notices a reduction of steering assistance sporadically while in certain driving situations. Steering control is never lost when the reduction of assistance occurs. Read More »
SPORADIC REDUCTION OF STEERING ASSISTANCE: This Service Information Bulletin (Revision 1) replaces SI B32 11 19 dated October 2019. The driver notices a reduction of steering assistance sporadically while in certain driving situations. Read More »
CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. Read More »
Power-assisted Steering Intermittently Not Available at Engine Start-up: This Service Information Bulletin (Revision 1) replaces SI B32 02 14 dated November 2016. The power-assisted steering is unavailable at start up/drive readiness. Read More »
SPORADIC REDUCTION OF STEERING ASSISTANCE. The driver notices a reduction of steering assistance sporadically while in certain driving situations. Steering control is never lost when the reduction of assistance occurs. Read More »
The electrical machine electronics (EME) Printed Circuit Board (PCB) may not have been produced to specifications. In the event that the EME detects this condition it will shut down high-voltage electrical power. Read More »
NOISE FROM FRONT AXLE WHEN STEERING: Chattering or squeaking noise is heard (refer to attached video https://tinyurl.com/y9kwrucl ) from the front axle under the following steering conditions: Read More »
Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. Read More »
Noises when turning the steering wheel. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all. Read More »
Steering wheel rubs/brushes against the steering column trim. When the steering wheel is moved, it rubs/brushes against the steering column trim. CAUSE Rear steering wheel trim. Read More »
CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. Read More »
CCM Brake system: Press pedal harder for usual braking power. Drive with caution to nearest authorized BMW Service workshop lights up. (Check Control message ID24) The fault usually only occurs at very low temperatures and in rainy regions. Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving. Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
AIR CONDITIONING DOES NOT COOL: The air conditioning no longer cools the vehicle. A vehicle test reveals one or both of the following faults stored in the IHX_I1 Control Module: 801295 - Heat Pump pressure-temperature sensor 2 after air ... Read More »
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Read More »
SI B12 12 15 Engine Electrical Systems February 2016 Technical Service This Service Information bulletin supersedes SI B12 12 15 dated February 2016. SUBJECT Service Engine Soon (MIL): EME FC CF948C. Read More »
For this vehicle, the EVAP systems purge (vent) valve limited warranty for defects in materials and/or workmanship has been extended to 15 years / 150,000 miles as determined from the original in-service date. Read More »
The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine. Read More »
For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Fuel Injectors to: 15 years/150,000 miles as determined by the vehicle's original in-service date. Read More »
I3 REX FRONT (UPSTREAM) OXYGEN SENSOR: If a vehicle listed above arrives with engine malfunction indicator (Check Engine) warning light on, performing a Vehicle Test. Read More »
I01 REX MISFIRES AT HIGH ALTITUDES USING WINTER-BLEND FUEL: The check engine light (MIL) is displayed, and in some cases the range extender (REx) engine will run rough for about 1 to 2 seconds during cold start. Read More »
TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. Read More »
THE DISPLAY GOES BLACK, VEHICLE DOESNT START AGAIN AFTER SWITCHING THE ENGINE OFF.: On board computer and navigation system goes black or resets. Read More »
SERVICE ENGINE SOON (MIL) - RDME FC 124301/124302. Malfunction indicator light illuminated. Fuel-air mixture error codes in the range extender digital motor electronics (RDME). Read More »
This Service Information bulletin supersedes SI B22 01 15 dated November 2015. designates changes to this revision SUBJECT Left Side Engine Mount Broken. The left side motor mount or motor mount support has failed. Read More »
ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL
EME FAULTS CANNOT BE READ IN ISTA: While diagnosing faults with in the EME, no fault details will appear and no relevant test plans will be linked. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
SUBJECT Correct Installation of W20 Catalytic Converter. Metallic noise from rear of vehicle equipped with a range extender. Improperly installed decoupling element allows contact with the heat shield. Read More »
The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine. Read More »
AIR CONDITIONING DOES NOT COOL: The air conditioning no longer cools the vehicle. A vehicle test reveals one or both of the following faults stored in the IHX_I1 Control Module: 801295 - Heat Pump pressure-temperature sensor 2 after air ... Read More »
SERVICE ACTION. REPLACE THE FUEL TANK PRESSURETEMPERATURE SENSOR. The internal sealing of the fuel tank pressure-temperature sensor may fail. Read More »
SPORADIC REDUCTION OF STEERING ASSISTANCE: This Service Information Bulletin (Revision 1) replaces SI B32 11 19 dated October 2019. The driver notices a reduction of steering assistance sporadically while in certain driving situations. Read More »
SERVICE ACTION: REPLACE THE FUEL TANK PRESSURETEMPERATURE SENSOR. The internal sealing of the fuel tank pressure-temperature sensor may fail. Read More »
For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Fuel Injectors to: 15 years/150,000 miles as determined by the vehicle's original in-service date. Read More »
SPORADIC REDUCTION OF STEERING ASSISTANCE: This Service Information Bulletin (Revision 1) replaces SI B32 11 19 dated October 2019. The driver notices a reduction of steering assistance sporadically while in certain driving situations. Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
The electrical machine electronics (EME) Printed Circuit Board (PCB) may not have been produced to specifications. In the event that the EME detects this condition it will shut down high-voltage electrical power. Read More »
SERVICE ACTION: KLE - CONVENIENCE CHARGING ELECTRONICS I01 REX: OBD relevant diagnoses of the KLE (convenience charging electronics) cannot be processed correctly because of a data transmission error in the EME (electrical machine ... Read More »
The vehicle may exhibit any of the following at very low State of Charge (SOC) ? less than 8%: - Power loss or high voltage system shutdown while running range extender (REx). - Inconsistent performance of the REx. Read More »
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. Read More »
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. Read More »
For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Fuel Injectors to: 15 years/150,000 miles as determined by the vehicle's original in-service date. Read More »
I3 REX FRONT (UPSTREAM) OXYGEN SENSOR: If a vehicle listed above arrives with engine malfunction indicator (Check Engine) warning light on, performing a Vehicle Test. Read More »
BMW TURBOCORD PORTABLE EV 120 V/240 V CHARGER: The BMW-approved accessory TurboCord electric vehicle (EV) charger will not charge the vehicle. Read More »
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Read More »
CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. Read More »
AIR CONDITIONING DOES NOT COOL: The air conditioning no longer cools the vehicle. A vehicle test reveals one or both of the following faults stored in the IHX_I1 Control Module: 801295 - Heat Pump pressure-temperature sensor 2 after air ... Read More »
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. Read More »
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER. A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Read More »
Power-assisted Steering Intermittently Not Available at Engine Start-up: This Service Information Bulletin (Revision 1) replaces SI B32 02 14 dated November 2016. The power-assisted steering is unavailable at start up/drive readiness. Read More »
High-Voltage Charging Cable Lock Malfunction: One of the following situations can occur: The vehicle cannot be charged via the high-voltage charging procedure. Read More »
The electrical machine electronics (EME) Printed Circuit Board (PCB) may not have been produced to specifications. In the event that the EME detects this condition it will shut down high-voltage electrical power. Read More »
BLUETOOTH CONNECTION IS LOST DURING A PHONE CALL. During an active call the call audio autonomously switches from the vehicle hands-free system to the phone. Read More »
STANDARD OCCASIONAL USE CABLE CHARGING COMPLAINT TROUBLESHOOTING This Service Information bulletin supersedes SI B61 19 18 dated November 2018. Read More »
PHONE CALL AUDIO AUTONOMOUSLY SWITCH FROM VEHICLE TO PHONE. During an active phone call the call audio autonomously switches from the vehicle hands-free system to the phone. Read More »
BLACK SPOT IN THE CENTRAL INFORMATION. This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: a?? Warranty section - Programming information added. Read More »
THE DISPLAY GOES BLACK, THE ENGINE CAN BE SWITCHED OFF ONLY VIA THE EMERGENCY-OFF.. * On board computer and navigation system goes black or resets. Read More »
STATIONARY CLIMATE CONTROL NOT WORKING AFTER HIGH VOLTAGE CHARGING. After the high voltage (HV) charging procedure, the stationary climate control (aka preconditioning) does not work. This is part of the normal design. Read More »
?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier). Read More »
"?REMOTE KEY WILL NOT OPEN OR START VEHICLE. Remote key battery in service significantly less (under a year) than expected two-year life-span. Read More »
SERVICE ACTION: KLE - CONVENIENCE CHARGING ELECTRONICS I01 REX: OBD relevant diagnoses of the KLE (convenience charging electronics) cannot be processed correctly because of a data transmission error in the EME (electrical machine ... Read More »
STATIONARY CLIMATE CONTROL NOT POSSIBLE WHEN SET FOR DEPARTURE TIME BETWEEN 0:00 AND 0:30 TIME RANGE: The programmed stationary climate control ventilation function does not switch on when the departure time is set between 0:00 and 0:30 ... Read More »
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when: Read More »
CHECK CONTROL STATES REMOTE KEY IS MISSING WHEN THE KEY IS LOCATED IN THE VEHICLE: Only affects vehicles that have been programmed with ISTA 4.10.1x and I-level 18-03-511 or 18-03-576 Read More »
EME SETS FAULT CODE 222931 OR LOW COST CHARGING NOT FUNCTIONAL AFTER PROGRAMMING: Fault code "222931 ? Charge management function: settings not calibrated" is stored in the Electrical Machine Electronics (EME), and/or "Low Cost Charging" ... Read More »
INSTRUMENT CLUSTER HAZES OVER. Customer notices a gray haze (shown below) on the instrument cluster face after: Instrument cluster was cleaned with a microfiber cloth. A film is removed from instrument cluster face after repair. Read More »
The vehicle may exhibit any of the following at very low State of Charge (SOC) ? less than 8%: - Power loss or high voltage system shutdown while running range extender (REx). - Inconsistent performance of the REx. Read More »
"SI B61 04 16 General Electrical June 2016 Technical Service EME Fault Code 222C02 Following Replacement or Programming- Diagnosis. Programming, (e.g. Read More »
"DC/DC Converter does not supply sufficient 12V power. Customer probably has a CCM stating ""Battery is not charged"" (CCM-ID: 213) is displayed. Read More »
DC Charging - Customer Focused Diagnosis. Diagnosing DC charging complaints requires a precise problem description from the customer, as well as thorough vehicle-side work to find a reliable root cause. Read More »
Drivetrain Malfunction (CCM 794) with Isolation Faults. The Drivetrain Malfunction check control message (CCM 794) is displayed, either while driving or when starting up. Read More »
The Charging Cable Does not Release from the Charging Socket after Charging. The charging cable does not release from the charging socket after charging. Read More »
SI B12 12 15 Engine Electrical Systems February 2016 Technical Service This Service Information bulletin supersedes SI B12 12 15 dated February 2016. SUBJECT Service Engine Soon (MIL): EME FC CF948C. Read More »
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued. Read More »
SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. Read More »
? Vehicles which have had the KOMBI (Instrument Cluster) replaced may display incorrect CBS (Condition Based Service) data after programming. Read More »
HEAD UNIT NBT EVO (HU-H2) PROGRAMMING ABORT: The CID screen may light up blue. When this occurs A battery reset is not successful in restoring head unit operation Software error in the Bootloader file (BTLD) of the head unit. Read More »
HIGH VOLTAGE DIAGNOSTIC SPECIALIST TRAINING AND EQUIPMENT STRATEGY. INFORMATION The ST1821 High Voltage Diagnostic Specialist Certification (HVS) is the next step in the E-mobility service strategy for BMW technicians. Read More »
High-Voltage Charging Cable Lock Malfunction: The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. Read More »
SERVICE ACTION: PROGRAMMING CONTROL UNITS (RANGE): The actual range can be inaccurate in relation to the state of charge of the high-voltage battery. Read More »
REMOTE KEY WILL NOT OPEN OR START VEHICLE: Remote key battery in service significantly less (under a year) than expected two-year life-span. Read More »
"A Delivery Stop has been issued on i01 (i3 Battery Electric Vehicle) produced from December 09, 2015 to January 22, 2016. These vehicles are equipped with a sunroof as part of the Shadow Sport limited edition. Read More »
High-Voltage Charging Cable Lock Malfunction: The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. Read More »
INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading. Read More »
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. Read More »
VEHICLE SOUND GENERATOR IS DIFFERENT AND LOUDER AFTER PROGRAMMING: Vehicles sound is different and louder after programming to an Integration level (I-level) between I001-1911-500 and I001-19-11-556. Read More »
HEAD UNIT NBT EVO (HU-H2) PROGRAMMING ABORT: The CID screen may light up blue. When this occurs A battery reset is not successful in restoring head unit operation Software error in the Bootloader file (BTLD) of the head unit. Read More »
AIRBAG INDICATOR LIGHT REMAINS ON AFTER SEAT OCCUPANCY MAT REPLACEMENT. The airbag indicator light illuminates after replacing the CIS (Capacitive Interior Sensing) mat. Read More »
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when: Read More »
NBT-EVO Head Unit Cannot be Swapped between Vehicles for Testing: If either the NBT-EVO head unit or Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit NBT-EVO to enter a locked mode once it ... Read More »
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION: Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Read More »
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION: Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Read More »
SERVICE ACTION - RENEW INTERIOR MIRROR HOLDER: The bonding of the interior mirror holder was not performed correctly. Incorrect bonding during production. Read More »
SERVICE ACTION - RENEW INTERIOR MIRROR HOLDER: The bonding of the interior mirror holder was not performed correctly. Incorrect bonding during production. Read More »
SERVICE ACTION - RENEW INTERIOR MIRROR HOLDER: The bonding of the interior mirror holder was not performed correctly. Incorrect bonding during production. Read More »
SERVICE ACTION: INSPECT REAR WINDOW. The rear window may be improperly bonded in the area shown above (red arrow), which could allow water to enter the luggage compartment. Read More »
SQUEAKING NOISE WHEN OPERATING THE SIDE WINDOWS: A squeaking noise is heard when operating either side window. Interference between the side window glass and the B-Pillar seal. Read More »
RATTLE NOISE IN SUNROOF AT HIGH TEMPERATURES. A rattle noise may be heard from the sunroof area with ambient temperatures above 80A?F with the sunroof glass in the vented position. Read More »
"This Service Information bulletin supersedes SI 54 01 16 dated February 2016. A Delivery Stop has been issued on i3 BEV vehicles produced from December 09, 2015 to January 22, 2016. Read More »
"A Delivery Stop has been issued on i01 (i3 Battery Electric Vehicle) produced from December 09, 2015 to January 22, 2016. These vehicles are equipped with a sunroof as part of the Shadow Sport limited edition. Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full: Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch. Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full : The low washer fluid warning is illuminated even though the washer fluid reservoir is full. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
STATIONARY CLIMATE CONTROL NOT WORKING AFTER HIGH VOLTAGE CHARGING. After the high voltage (HV) charging procedure, the stationary climate control (aka preconditioning) does not work. This is part of the normal design. Read More »
STEERING ASSISTANCE SPORADIC REDUCTION: The driver notices a reduction of steering assistance sporadically while in certain driving situations. Steering control is never lost when the reduction of assistance occurs. Read More »
SPORADIC REDUCTION OF STEERING ASSISTANCE: This Service Information Bulletin (Revision 1) replaces SI B32 11 19 dated October 2019. The driver notices a reduction of steering assistance sporadically while in certain driving situations. Read More »
AIRBAG INDICATOR LIGHT REMAINS ON AFTER SEAT OCCUPANCY MAT REPLACEMENT. The airbag indicator light illuminates after replacing the CIS (Capacitive Interior Sensing) mat. Read More »
A Check Control Message is displayed for the Tailgate Lock Open: A Check Control Message is displayed indicating that the tailgate is open even though it is mechanically closed. Faulty tailgate lock or incorrect adjustment. Read More »
SAFETY BELT WARNING GONG SOUNDS AFTER UNBUCKLING WHILE VEHICLE IS STATIONARY. After a vehicle has been programmed to an I-level greater than 19-11-5xx and lower than I-level 20-03-530; the safety belt (aka seat belt) acoustic warning ... Read More »
SQUEAKING NOISE WHEN OPERATING THE SIDE WINDOWS: A squeaking noise is heard when operating either side window. Interference between the side window glass and the B-Pillar seal. Read More »
"A Delivery Stop has been issued on i01 (i3 Battery Electric Vehicle) produced from December 09, 2015 to January 22, 2016. These vehicles are equipped with a sunroof as part of the Shadow Sport limited edition. Read More »
SI B36 04 14 Wheels and Tires January 2016 Technical Service. This Service Information bulletin supersedes SI 36 04 14 dated September 2014. SUBJECT: Rolling Tire Noise . Read More »
"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following ... Read More »
BMW MAINTENANCE BOOKLET AND OEM TIRE MANUFACTURERS' WARRANTIES: In efforts to provide a digital experience to our customers, BMW of North America, LLC (BMW NA) is proud to announce a digital version of both the BMW Maintenance Booklet and ... Read More »
SI B36 04 14 Wheels and Tires January 2016 Technical Service. This Service Information bulletin supersedes SI 36 04 14 dated September 2014. SUBJECT: Rolling Tire Noise . Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving. Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
SI B36 04 14 Wheels and Tires January 2016 Technical Service. This Service Information bulletin supersedes SI 36 04 14 dated September 2014. SUBJECT: Rolling Tire Noise . Read More »
CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following ... Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
AIR CONDITIONING DOES NOT COOL: The air conditioning no longer cools the vehicle. A vehicle test reveals one or both of the following faults stored in the IHX_I1 Control Module: 801295 - Heat Pump pressure-temperature sensor 2 after air ... Read More »
DELIVERY STOP: CHARGING CABLE (NON-TURBOCORD VERSION): BMW AG has issued a Delivery Stop (effective May 3, 2021) on a small number of Model Year 2021 BMW i3 vehicles that were produced between March 1, 2021 and April 26, 2021. Read More »
I3 REX FRONT (UPSTREAM) OXYGEN SENSOR: If a vehicle listed above arrives with engine malfunction indicator (Check Engine) warning light on, performing a Vehicle Test. Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full: Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch. Read More »
VEHICLE SOUND GENERATOR IS DIFFERENT AND LOUDER AFTER PROGRAMMING: Vehicles sound is different and louder after programming to an Integration level (I-level) between I001-1911-500 and I001-19-11-556. Read More »
CHARGING SOCKET EMERGENCY RELEASE DAMAGED: The tensioning strap of the emergency charging socket release has been damaged. Charging Socket Emergency release (2). Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full : The low washer fluid warning is illuminated even though the washer fluid reservoir is full. Read More »
SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO. Read More »
HIGH VOLTAGE DIAGNOSTIC SPECIALIST TRAINING AND EQUIPMENT STRATEGY. INFORMATION The ST1821 High Voltage Diagnostic Specialist Certification (HVS) is the next step in the E-mobility service strategy for BMW technicians. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
PHONE CALL AUDIO AUTONOMOUSLY SWITCH FROM VEHICLE TO PHONE. During an active phone call the call audio autonomously switches from the vehicle hands-free system to the phone. Read More »
"?REMOTE KEY WILL NOT OPEN OR START VEHICLE. Remote key battery in service significantly less (under a year) than expected two-year life-span. Read More »
PHONE CONTACTS: HEADUNIT BASIC 2 SORTING ORDER: Improper sorting of phone contacts, in the on-board computer or in the Central Information Display (CID), upon connecting to the vehicle: Read More »
COMPONENT PROTECTION ACTIVE. HEAD UNITS CANNOT BE SWAPPED BETWEEN VEHICLES FOR TESTING.: If either the head unit (NBT-EVO or ENTRY-NAV-EVO) or the Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head ... Read More »
NBT-EVO Head Unit Cannot be Swapped between Vehicles for Testing: If either the NBT-EVO head unit or Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit NBT-EVO to enter a locked mode once it ... Read More »
CHECK CONTROL STATES REMOTE KEY IS MISSING WHEN THE KEY IS LOCATED IN THE VEHICLE: Only affects vehicles that have been programmed with ISTA 4.10.1x and I-level 18-03-511 or 18-03-576 Read More »
IPHONE: CALL LIST MISSING AFTER RESTART: The call list from iPhone 8 or iPhone X, that is displayed, is missing after cycling the ignition. Read More »
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when: Read More »
NBT-EVO Head Unit Cannot be Swapped between Vehicles for Testing. 'Component Protection Active': If either the NBT-EVO head unit or Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit NBT-EVO to ... Read More »
ConnectedDrive/BMW Assist System Diagnosis Information This Service Information bulletin replaces SI B84 02 14 dated July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Read More »
SI B65 09 15 November 2016 Audio, Navigation, Monitors, Alarms,SRS Technical Service NBT Head Unit High (HU-H) Resets Intermittently or Permanently. The Head Unit-High (HU-H) resets intermittently or permanently. 1. Read More »
The Charging Cable Does not Release from the Charging Socket after Charging. The charging cable does not release from the charging socket after charging. Read More »
"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following ... Read More »
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. Read More »
Engine and Gearbox Suspension. Technical Service his Service Information bulletin supersedes SI B22 01 15 dated February 2016. A sudden loss of traction while accelerating sharply may damage the engine mounts. Read More »
Noises when turning the steering wheel. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all. Read More »
Steering wheel rubs/brushes against the steering column trim. When the steering wheel is moved, it rubs/brushes against the steering column trim. CAUSE Rear steering wheel trim. Read More »
TELEMATICS UNIT DEACTIVATION DUE TO 3G CELLULAR TECHNOLOGY DISCONTINUATION: The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network ... Read More »
PHONE CALL AUDIO AUTONOMOUSLY SWITCH FROM VEHICLE TO PHONE. During an active phone call the call audio autonomously switches from the vehicle hands-free system to the phone. Read More »
THE CHARGING CABLE DOES NOT RELEASE FROM THE CHARGING SOCKET AFTER CHARGING: The charging cable does not release from the charging socket after charging. Read More »
SERVICE ACTION: KLE - CONVENIENCE CHARGING ELECTRONICS I01 REX: OBD relevant diagnoses of the KLE (convenience charging electronics) cannot be processed correctly because of a data transmission error in the EME (electrical machine ... Read More »
CHECK CONTROL STATES REMOTE KEY IS MISSING WHEN THE KEY IS LOCATED IN THE VEHICLE: Only affects vehicles that have been programmed with ISTA 4.10.1x and I-level 18-03-511 or 18-03-576 Read More »
IPHONE: CALL LIST MISSING AFTER RESTART: The call list from iPhone 8 or iPhone X, that is displayed, is missing after cycling the ignition. Read More »
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when: Read More »
A/C FAILURE: FC 801252 ELECTRIC A/C COMPRESSOR: INTERNAL FAULT DETECTED: Air conditioning (A/C) failure with IHKA fault code "801252 - Electric A/C compressor: Internal fault detected". Read More »
NO AUDIO PLAYBACK AFTER REPLACING THE HEAD UNIT HIGH 2 (HU-H2): After replacing the Head Unit High (HU-H2) and performing ISTA4 programming, there is no audio playback. Read More »
Bluetooth Connection Failures: There are various connectivity failures with the following devices: Apple iPhones: Samsung S6 and the S6 Edge. Read More »
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. Read More »
CONNECTEDDRIVE-REMOTE SERVICES DO NOT FUNCTION: Remote Services (such as locking and unlocking the car, vehicle location by honking the horn, flashing the lights or on the map in the BMW Connected App) do not function after vehicle has ... Read More »
NO AUDIO PLAYBACK AFTER REPLACING THE HEAD UNIT HIGH 2 (HU-H2): After replacing the Head Unit High (HU-H2) and performing ISTA4 programming, there is no audio playback. Read More »
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. Read More »
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. Read More »
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for ... Read More »
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for ... Read More »
NBT-EVO Head Unit Cannot be Swapped between Vehicles for Testing: If either the NBT-EVO head unit or Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit NBT-EVO to enter a locked mode once it ... Read More »
BMW MAINTENANCE BOOKLET AND OEM TIRE MANUFACTURERS' WARRANTIES: In efforts to provide a digital experience to our customers, BMW of North America, LLC (BMW NA) is proud to announce a digital version of both the BMW Maintenance Booklet and ... Read More »
INFORMATION New information provided by this revision is preceded by this symbol. This Service Information bulletin replaces SI B84 02 14 dated September 2018. Read More »
I3 REX FRONT (UPSTREAM) OXYGEN SENSOR: If a vehicle listed above arrives with engine malfunction indicator (Check Engine) warning light on, performing a Vehicle Test. Read More »
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. Read More »
BLUETOOTH CONNECTION IS LOST DURING A PHONE CALL. During an active call the call audio autonomously switches from the vehicle hands-free system to the phone. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
"?REMOTE KEY WILL NOT OPEN OR START VEHICLE. Remote key battery in service significantly less (under a year) than expected two-year life-span. Read More »
SUBJECT Correct Installation of W20 Catalytic Converter. Metallic noise from rear of vehicle equipped with a range extender. Improperly installed decoupling element allows contact with the heat shield. Read More »
This Service Information bulletin supersedes SI B22 01 15 dated November 2015. designates changes to this revision SUBJECT Left Side Engine Mount Broken. The left side motor mount or motor mount support has failed. Read More »
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued. Read More »
SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. Read More »
A/C FAILURE: FC 801252 ELECTRIC A/C COMPRESSOR: INTERNAL FAULT DETECTED: Air conditioning (A/C) failure with IHKA fault code "801252 - Electric A/C compressor: Internal fault detected". Read More »
KNOCKING NOISE FROM RF WHEEL AREA WHEN A/C IS ACTIVATED. A knocking noise is heard when entering drive readiness or after driving a short distance with the air conditioning activated. Read More »
Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials. Read More »
