Technical Service Bulletins (TSBs) for the 2013 S5 are official communications between Audi & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 45 number 13-07 dated September 25, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-47 dated August 2, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 97 number 13-35 dated March 27, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. Read More »
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-45 dated July 10, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. Read More »
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). Read More »
Supersedes Technical Service Bulletin Group 48 number 13-39 dated March 18, 2013. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. Read More »
Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-38 dated March 18, 2013. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-36 dated February 21, 2013. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-34 dated November 13, 2012. Customers may report the following conditions on vehicles with less than 6000 miles. In some cases these conditions may be noticed at PDI. Read More »
The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. Read More »
This document contains the Audi TAC technical newsletter. The news letter contains information on the Audi TAC hours of operation, the Audi technical assistance survey, the 4. Read More »
The MIL is on for steering related faults. This Update is in effect until removed. Procedure is valid only for vehicles that show the 48K4 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Read More »
This document contains information on delivering the perfect audi vehicle and to pay special attention to completing any update technical bulletins that are active on the 2013 model year vehicles. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
This communication is to inform you of Update 48K4. On Audi vehicles with electromechanical power steering manufactured within a specific period, an irregularity detected by the diagnosis function can result in an implausible status ... Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Read More »
AUDI: MULTIPLE DIAGNOSTIC TROUBLE CODES (DTC) ASSOCIATED WITH POOR INTERNAL CONTACT OF CIRCUIT BOARD (GEARBOX) WHERE OIL ADDITIVES CAN CAUSE PLASTIC CIRCUIT PLATES TO DELAMINATE AND CONTACT LOSS. MODEL 2010-2013 S4, S5, RS5, S6, S7. Read More »
Supersedes Technical Service Bulletin Group 35 number 13-14 dated August 30, 2013. Message appears in the information display: "Gearbox malfunction: you can continue driving". Read More »
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. Read More »
Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. Read More »
Customer may report that a warning for electromechanical steering is displayed in the instrument cluster. There is no loss of steering control or functionality associated with these warnings. Issues with the hardware and software. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-36 dated February 21, 2013. The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. Read More »
The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
The adaptive damping suspension control module, J250, cannot be coded via SVM spec/actual after it has been replaced. A new generation of the adaptive damping suspension control module, J250, was placed into production. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-34 dated November 13, 2012. Customers may report the following conditions on vehicles with less than 6000 miles. In some cases these conditions may be noticed at PDI. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be reduced. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-17 dated July 14, 2015. Customer may complain about brake squeak or squeal with light to moderate pedal pressure. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-68 dated February 3, 2014. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 47 number 12-04 dated September 5, 2012. Rattling noises are heard from the front axle when the vehicle is driven over bumpy or rough roads. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-67 dated January 21, 2014. Customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-64 dated January 2, 2014. Customer may report hearing brake noise from front or rear brakes. Read More »
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Read More »
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Read More »
Supersedes Technical Service Bulletin Group 46 number 13-53 dated August 7, 2013. Customer may report hearing brake noise from front or rear brakes. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-17 dated January 18, 2012. The customer may complain of hearing a high-pitched squeal or squeak from the brake system when brakes are used with light to moderate effort. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-11 dated June 29, 2015. Customer may complain about brake squeak or squeal with light to moderate pedal pressure from front brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-89 dated July 21, 2014. Customer may complain about brake squeak or squeal with light to moderate pedal pressure. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 46 number 13-36 dated April 9, 2013. The customer may complain of hearing a high-pitched squeal or squeak from the brake system when brakes are used with light to moderate effort. Read More »
AUDI: DUE TO DAMAGE ABS WHEEL SPEED SENSOR DURING PRODUCTION, SOME VEHICLES MAY EXPERIENCE STEERING WHEEL NOT LOCKING, IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. Read More »
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29. Read More »
AUDI: DUE TO DAMAGE ABS WHEEL SPEED SENSOR DURING PRODUCTION, SOME VEHICLES MAY EXPERIENCE STEERING WHEEL NOT LOCKING, IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. Read More »
Incorrect tolerances of cruise control ?Set? button. Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. ?Set? button on cruise control stalk does not work. Read More »
Supersedes Technical Service Bulletin Group 53 number 13-02 dated July 11, 2013. Customer may report that the vehicle does not start due to a discharged battery. Read More »
Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 ... Read More »
Incorrect tolerances of cruise control ?Set? button. Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. ?Set? button on cruise control stalk does not work. Read More »
The customer may state the yellow warning for electric parking brake (EPB) appeared once in the instrument cluster, but the warning turned OFF after cycling the ignition and there have been no additional occurrences. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-34 dated October 8, 2013. The MIL is on. DTCs are stored in the ECM. There may be slight power reduction at high RPMs. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-02 dated May 29, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO VERIFY A RATTLING NOISE HEARD AT COLD START AND TO REPLACE BOTH UPPER CHAIN TENSIONERS OF BANK 1 AND BANK 2 WITH AN OPTIMIZED PART. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
AUDI: ON SOME VEHICLES, THE ENGINE WARNING LIGHT SPORADICALLY WILL ILLUMINATE, OR HAVE REDUCED ENGINE PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, OR NOISE CAN BE HEARD COMING FROM ENGINE HIGH PRESSURE FUEL PUMPS 2. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-34 dated October 8, 2013. The MIL is on. DTCs are stored in the ECM. There may be slight power reduction at high RPMs. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-28 dated November 14, 2013. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. Read More »
AUDI: THE OIL FILTER, FOR SOME VEHICLES, ARE TOO SHORT, (SHOULD BE 155 (=/-1) MM LONG) FOR INSTALLATION AND DRAIN FLAP, IN OIL FILTER HOUSING, CAN NOT COMPLETELY CLOSE CAUSING LOST OF OIL PRESSURE. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-78 dated March 20, 2013. DTC is stored in the engine control module. Red oil pressure warning light may be on. An oil filter that is too short is installed. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-26 dated August 29, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
AUDI: DUE TO DEFECTIVE VACUUM ACTUATORS, SOME VEHICLES EXPERIENCE HIGH RPMS WITH A POWER REDUCTION, INTAKE MANIFOLD RUNNER CONTROL STUCK CLOSED (BANK 1 AND BANK 2) POWER AND VACUUM ACTUATOR NEEDS TO BE UPDATED. Read More »
MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. Read More »
AUDI: ON SOME VEHICLES, A DEFECT HAS OCCURRED ON ONE OF THE VACUUM ACTUATORS ON THE INTAKE RUNNER BANK 1 OR BANK 2 AND NEEDS TO BE UPDATED. MODELS 2013 A6/ A7, S4, S5, S5 CABRIO, AUDI Q7, AUDI A5. *PE UPDATED 12/2/13. Read More »
MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. Read More »
AUDI: ON SOME VEHICLES, THERE IS A DEFECT PERTAINING TO INTAKE RUNNER BANK 1 OR BANK 2 FROM ONE OF THE VACUUM ACTUATORS. MODELS 2013 A6, A7, S4, S5, S5 CABRIO, AUDI Q7, AUDI Q5. *PE Read More »
AUDI: ON SOME VEHICLES, THE INTAKE RUNNER BANK 1 OR BANK 2 IS DEFECTIVE, DUE TO ONE OF THE VACUUM ACTUATORS, CAUSING A SLIGHT POWER REDUCTION AT HIGH RPMS. MODELS 2013 A6/ A7, S4, S5, S5 CAB, AUDI Q7, AUDI Q5. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 17 number 12 - 31 dated August 30, 2012. Oil consumption measurement - Repair Authorization (CA). Read More »
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM. Read More »
The MIL is on. DTCs P2440(00) and/or P2442(00) are stored in the ECM. One of the combi valves is defective or the vacuum solenoid is defective. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-45 dated September 3, 2013. The coolant warning light is illuminated. Coolant is leaking from the front intercooler radiator because of stone damage to the radiator. Read More »
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). Read More »
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). Read More »
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function. Read More »
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function. Read More »
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function. Read More »
The NVLD pressure switch may erroneously detect a very small leak. New pressure sensors in production: ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, that are separate (two ... Read More »
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be lost. Read More »
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be lost. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function. Read More »
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function. Read More »
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function. Read More »
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-43 dated July 12, 2013. The coolant warning light is illuminated. Coolant is leaking from the front intercooler radiator because of stone damage to the radiator. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-89 dated May 2, 2013. MIL on. A cylinder misfire fault (DTC P0301 - P0306) with DTC P130A is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-20 dated August 2, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
This communication is to inform you of upcoming Update 24Z6. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-16 dated July 19, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 35 number 12-07 dated December 21, 2012. Customer may report that there is oil leaking under the vehicle. There are a number of possible sources for the leak. Leaking from the oil pan seal. Read More »
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
DTC P164D00 (Oil pressure switch for reduced oil pressure malfunction) is stored in the engine control module, J623 (01). Red oil pressure warning light may be on. An oil filter that is too short is installed. The oil filter must be 155 mm. Read More »
To ensure mobility, a small amount of fuel is still available when a fuel range of zero miles is initially displayed. Additionally, the fuel range is calculated based on the most recent driving style. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be lost. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-45 dated September 3, 2013. The coolant warning light is illuminated. Coolant is leaking from the front intercooler radiator because of stone damage to the radiator. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-43 dated July 12, 2013. The coolant warning light is illuminated. Coolant is leaking from the front intercooler radiator because of stone damage to the radiator. Read More »
When vehicles are driven on gravel roads, there is a greater chance of front-end stone impact damage to the intercooler radiator (Figure 1). Read More »
When vehicles are driven on gravel roads, there is a greater chance of front-end stone impact damage to the intercooler radiator (Figure 1). Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
Transmission control module (TCM) software designed and certified for a similar model/model year was used in vehicles affected by this action. It is undetermined whether there could be an impact to emissions. Read More »
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored. Read More »
As part of Audi's ongoing commitment to our environment, Audi is extending the Emissions Control Systems Warranty to cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 ... Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. Read More »
AUDI: DUE TO DEFECTIVE VACUUM ACTUATORS, SOME VEHICLES EXPERIENCE HIGH RPMS WITH A POWER REDUCTION, INTAKE MANIFOLD RUNNER CONTROL STUCK CLOSED (BANK 1 AND BANK 2) POWER AND VACUUM ACTUATOR NEEDS TO BE UPDATED. Read More »
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present. Read More »
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake ... Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
The NVLD pressure switch may erroneously detect a very small leak. New pressure sensors in production: ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, that are separate (two ... Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Customer may report that there is oil leaking under the vehicle. There are a number of possible sources for the leak, including: Leaking from the oil pan seal (Figure 1). Crack in the oil pan (Figure 2). Read More »
The instrument cluster displays a fuel range of zero miles before the fuel tank is completely empty. Upon refueling at a displayed fuel range of zero miles, the fuel tank accepts fewer gallons than what is shown in the owner? s manual ... Read More »
To ensure mobility, a small amount of fuel is still available when a fuel range of zero miles is initially displayed. Additionally, the fuel range is calculated based on the most recent driving style. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present. Read More »
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND. Read More »
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, ... Read More »
FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND. Read More »
Transmission control module (TCM) software designed and certified for a similar model/model year was used in vehicles affected by this action. It is undetermined whether there could be an impact to emissions. Read More »
This bulletin contains software update information for the transmission when a bump can be felt just after the vehicle is brought to a stop or when a rattle noise is heard at idle speed. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-34 dated October 8, 2013. The MIL is on. DTCs are stored in the ECM. There may be slight power reduction at high RPMs. Read More »
Supersedes Technical Service Bulletin Group 35 number 13-14 dated August 30, 2013. Message appears in the information display: "Gearbox malfunction: you can continue driving". Read More »
Supersedes Technical Service Bulletin Group 35 number 13-13 dated July 12, 2013. The following message appears in the information display: "Gearbox malfunction: you can continue driving". Read More »
MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. Read More »
Supersedes Technical Service Bulletin Group 35 number 13-10 dated May 7, 2013. The following message appears in the information display: "Gearbox malfunction: you can continue driving". Read More »
MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. Read More »
This document contains the Audi TAC technical newsletter. The news letter contains information on the Audi TAC hours of operation, the Audi technical assistance survey, the 4. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks ... Read More »
There may be clutch mechanism wear. Customer may report that the vehicle does not start or only starts when the clutch pedal is pressed very firmly. The message ?Press clutch pedal to start vehicle? may appear in the instrument cluster. Read More »
POWER TRAIN:MANUAL TRANSMISSION:COLUMN SHIFT ASSEMBLY
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR DIAGNOSING AN ISSUE WITH THE MECHATRONICS CONTROL UNIT CIRCUIT BOARD AND INSTRUCTIONS FOR REPLACING IT. Read More »
Gearbox malfunction message in cluster. DTCs P17D800, P179D00, P174000, P174C, P174B, P174F, P179C, P174A, and/or P174E are stored in the transmission control module. Read More »
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Read More »
Transmission control module (TCM) software designed and certified for a similar model/model year was used in vehicles affected by this action. It is undetermined whether there could be an impact to emissions. Read More »
Transmission control module (TCM) software designed and certified for a similar model/model year was used in vehicles affected by this action. It is undetermined whether there could be an impact to emissions. Read More »
Transmission control module (TCM) software designed and certified for a similar model/model year was used in vehicles affected by this action. It is undetermined whether there could be an impact to emissions. Read More »
This bulletin contains repair instructions for when DTC P179E00 is stored and the mechantronic unit and/or gear sensor G676 are being replaced. Read More »
The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow. Read More »
This document contains information on delivering the perfect audi vehicle and to pay special attention to completing any update technical bulletins that are active on the 2013 model year vehicles. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. Read More »
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be reduced. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present. Read More »
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored. Read More »
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-26 dated June 30, 2015. The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM). Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 35 number 12-08 dated December 21, 2012. The driver information system displays the message ?Gearbox malfunction: you can continue driving?. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-42 dated November 21, 2013. DTC P164D00 is stored in the engine control module. Red oil pressure warning light may be on. An oil filter that is too short is installed. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. Read More »
Supersedes Technical Service Bulletin Group 45 number 13-07 dated September 25, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-28 dated November 14, 2013. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. Read More »
Supersedes Technical Service Bulletin Group 27 number 13-17 dated April 5, 2013. Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. ?Set? button on cruise control stalk does not work. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-27 dated October 16, 2013. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 53 number 13-02 dated July 11, 2013. Customer may report that the vehicle does not start due to a discharged battery. Read More »
Poor internal contact area on circuit board will lead to faults. Oil additives can cause the plastic circuit plates to delaminate, causing contact loss. Read More »
Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 ... Read More »
Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-60 dated May 23, 2013. Audi Lane Change Assistant (Side Assist) deactivates or is sporadically inoperative when the vehicle is driven in slow-moving, stop-and-go traffic or when it ... Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
It is possible that objects have been inserted into the ignition lock, which causes the slide of the ignition lock to become stuck in the rear part of the lock (S-contact position). Read More »
There may be clutch mechanism wear. Customer may report that the vehicle does not start or only starts when the clutch pedal is pressed very firmly. The message ?Press clutch pedal to start vehicle? may appear in the instrument cluster. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
This document contains information on delivering the perfect audi vehicle and to pay special attention to completing any update technical bulletins that are active on the 2013 model year vehicles. Read More »
The customer may state the yellow warning for electric parking brake (EPB) appeared once in the instrument cluster, but the warning turned OFF after cycling the ignition and there have been no additional occurrences. Read More »
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing ... Read More »
This communication is to inform you of Update 48K4. On Audi vehicles with electromechanical power steering manufactured within a specific period, an irregularity detected by the diagnosis function can result in an implausible status ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-49 dated April 25, 2014. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. Read More »
Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). Read More »
Supersedes Technical Service Bulletin Group 87 number 12-37 dated November 16, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. Read More »
The MIL is on. DTCs P2440(00) and/or P2442(00) are stored in the ECM. One of the combi valves is defective or the vacuum solenoid is defective. Read More »
Supersedes Technical Service Bulletin Group 55 number 13-30 dated May 28, 2013. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. Read More »
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-51 dated August 18, 2014. The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with ... Read More »
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed ... Read More »
Supersedes Technical Service Bulletin Group 30 number 11-11 dated December 9, 2011. Customer may report that the vehicle does not start or only starts when the clutch pedal is pressed very firmly. Read More »
Adaptive Cruise Control (ACC) does not work. The message "ACC no sensor vision" appears in the cluster. DTCs are logged in the distance regulation control module, J428 (13). Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT
Transmission control module (TCM) software designed and certified for a similar model/model year was used in vehicles affected by this action. It is undetermined whether there could be an impact to emissions. Read More »
Transmission control module (TCM) software designed and certified for a similar model/model year was used in vehicles affected by this action. It is undetermined whether there could be an impact to emissions. Read More »
This bulletin contains software update information for the transmission when a bump can be felt just after the vehicle is brought to a stop or when a rattle noise is heard at idle speed. Read More »
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the ECM. New ECM software implemented to correct the condition. Read More »
The MIL is on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Bump felt just after the vehicle is brought to a stop. Rattle noise heard from transmission at idle speed. The software of the transmission mechatronic control module, J743, needs to be updated. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-71 dated March 13, 2014. The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or ... Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or ... Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 46 number 12-26 dated October 23, 2012. The yellow warning for electromechanical parking park (EPB) appeared once in the instrument cluster. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 01 number 13-06 dated June 18, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-05 dated June 7, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-03 dated May 29, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
AUDI: WHILE DRIVING IN STOP AND GO TRAFFIC, SLOW MOVING TRAFFIC, OR DRIVING FOR LONG PERIODS OF TIME WITH NO TRAFFIC, SOME VEHICLES' SIDE ASSIST MAY DEACTIVATE OR BECOME SPORADICALLY INOPERATIVE. Read More »
Customer may report that a warning for electromechanical steering is displayed in the instrument cluster. There is no loss of steering control or functionality associated with these warnings. Issues with the hardware and software. Read More »
This communication is to inform you that Update 48K4 has been closed. We have turned off visibility for this Update while an alternate software solution is being developed. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light ... Read More »
Supersedes Technical Service Bulletin Group 94 number 12-96 dated November 1, 2012. Part or all of the daytime running lights do not work on vehicles equipped with LED daytime running lights. Read More »
TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Read More »
Supersedes Technical Service Bulletin Group 94 number 11-52 dated October 11, 2011. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third ... Read More »
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake ... Read More »
A significant amount of water is collecting at the base of the Xenon headlight lens. No outside influence, such as rock chips, can be found. The headlights function normally. Read More »
Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. Read More »
This document contains information on delivering the perfect audi vehicle and to pay special attention to completing any update technical bulletins that are active on the 2013 model year vehicles. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. Read More »
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
Customer may report that there is oil leaking under the vehicle. There are a number of possible sources for the leak, including: Leaking from the oil pan seal (Figure 1). Crack in the oil pan (Figure 2). Read More »
Supersedes Technical Service Bulletin Group 35 number 13-12 dated June 18, 2013. Customer may report that there is oil leaking under the vehicle. Leaking from the oil pan seal. Crack in the oil pan. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-70 dated September 5, 2012. Vibration noises from the doors or the rear parcel shelf are heard, particularly when heavy bass audio is playing. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. Read More »
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. Read More »
Supersedes Technical Service Bulletin Group 55 number 13-30 dated May 28, 2013. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. Read More »
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph. Read More »
Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. "Set" button on cruise control stalk does not work. DTCs are present in the vehicle. Incorrect tolerances of cruise control "Set" button. Read More »
THIS TECHNICAL SERVICE BULLETIN NOTIFIES THE READER THAT IF THE TPMS MESSAGE APPEARS BRIEFLY AFTER THE ENGINE IS STARTED AND THEN DISAPPEARS, IT DOES NOT INDICATE AN ISSUE WITH THE TPMS SYSTEM. Read More »
Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. The "TPMS" message is not related to a loss of tire pressure. Read More »
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and ... Read More »
Supersedes Technical Service Bulletin Group 48 number 13-47 dated August 2, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
The customer may state the yellow warning for electric parking brake (EPB) appeared once in the instrument cluster, but the warning turned OFF after cycling the ignition and there have been no additional occurrences. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-76 dated September 23, 2013. Customer complains that Audi Side Assist is providing false warnings (no vehicle is present). Concern may or may not be duplicated. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-76 dated September 23, 2013. Customer complains that Audi Side Assist is providing false warnings (no vehicle is present). Concern may or may not be duplicated. Read More »
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the ... Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage. Read More »
This bulletin contains repair instructions for when DTC P179E00 is stored and the mechantronic unit and/or gear sensor G676 are being replaced. Read More »
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward. Read More »
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has ... Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin. Read More »
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed. Read More »
Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the ... Read More »
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. Read More »
Poor internal contact area on circuit board will lead to faults. Oil additives can cause the plastic circuit plates to delaminate, causing contact loss. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-98 dated May 17, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
The MIL is on for steering related faults. This Update is in effect until removed. Procedure is valid only for vehicles that show the 48K4 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Read More »
This document contains information on delivering the perfect audi vehicle and to pay special attention to completing any update technical bulletins that are active on the 2013 model year vehicles. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
The instrument cluster displays a fuel range of zero miles before the fuel tank is completely empty. Upon refueling at a displayed fuel range of zero miles, the fuel tank accepts fewer gallons than what is shown in the owner? s manual ... Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-52 dated September 2, 2014. The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level (when measured ... Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 91 number 14-19 dated January 3, 2014. Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a ... Read More »
Supersedes Technical Service Bulletin Group 57 number 12-70 dated September 5, 2012. Vibration noises from the doors or the rear parcel shelf are heard, particularly when heavy bass audio is playing. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 28 number 12-19 dated May 1, 2012. The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Read More »
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-90 dated June 5, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or ... Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
Supersedes Technical Service Bulletin Group 91 number 10-68 dated October 26, 2010. The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected. Read More »
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s). Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Customer may report that there is oil leaking under the vehicle. There are a number of possible sources for the leak, including: Leaking from the oil pan seal (Figure 1). Crack in the oil pan (Figure 2). Read More »
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. Read More »
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This technical service bulletin provides instructions for diagnosing an issue with the mechatronics control unit circuit board and instructions for replacing it. Read More »
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Read More »
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. Read More »
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center Read More »
This document contains additional information not included in the booklet part number A5S5QUSPEC201 which contains communication tightening specifications Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. Read More »
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release ... Read More »
Supersedes Technical Service Bulletin Group 96 number 13-56 dated May 2, 2013. Customer complains that Audi Side Assist is providing false warnings (no vehicle is present). Concern may or may not be duplicated. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Read More »
Supersedes Technical Service Bulletin Group 87 number 14-49 dated April 25, 2014. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-44 dated August 26, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. Read More »
This communication is to inform you of upcoming Update 87D9. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-43 dated July 12, 2013. Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-42 dated June 11, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-37 dated November 16, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing ... Read More »
