Technical Service Bulletins (TSBs) for the 2014 A8 are official communications between Audi & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Steering angle sensor cannot be programmed. The steering angle sensors cannot be calibrated and the steering end stops cannot be adapted on a vehicle with dynamic steering. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-77 dated May 21, 2014. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
RUNNING GEAR: AUDI MAGNETIC RIDE - KNOCKING NOISES FROM REAR SHOCKS ON S3 (8V) AND TTS (FV) BRAKE SYSTEM: BRAKING NOISES - BASIC PRINCIPALS FOR DIAGNOSIS AND REPAIR. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
The electromechanical parking brake warning is illuminated in the instrument cluster. DTCs are stored in the electromechanical parking brake control module. Read More »
Customer may report hearing brake squeal when the vehicle comes to a stop at slow speeds. In some cases, the noise may be intermittent and difficult to reproduce. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-68 dated February 3, 2014. The customer may report hearing brake noise from front or rear brakes. Read More »
Customer reports hearing brake squeal when the vehicle comes to a stop at slow speeds. In some cases, the noise may be intermittent and difficult to reproduce. Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
Customer may report hearing a high-pitched squeal or squeak from the front brake system when brakes are used with light to moderate effort. Various parts have been replaced under warranty for the condition noted above. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 46 number 13-52 dated July 31, 2013. Customer may report hearing a high-pitched squeal or squeak from the front brake system when brakes are used with light to moderate effort. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit. Read More »
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29. Read More »
This bulletin contains repair instructions for DTCs C100E01, C100E12, C100D01, and C100D12 with an electromechanical parking brake warning light in the cluster. Read More »
AUDI: A6, A7, A8 2014-2015 ELECTRONIC WARNING PARKING BRAKE WARNING LIGHT ON INSTRUMENT CLUSTER, WHICH IS CAUSED BY THE PARKING BRAKE CONTROL MODULE. *LJ Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when the MIL is on and one of many DTCs is stored in relation to dylinder on demand function. Read More »
This is an informational bulletin requesting that dealers with the V6 TDI engine call TAC for instructions when they receive one of six DTCS in conjunction with DFCC symptom codes between 19184 and 19189. Read More »
This technical service bulletin provides instructions for troubleshooting and repairing the camshaft adjustment valve to correct a concern about the engine running irregularly. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AND REPAIRING THE CAMSHAFT ADJUSTMENT VALVE TO CORRECT A CONCERN ABOUT THE ENGINE RUNNING IRREGULARLY. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AND REPAIRING THE CAMSHAFT ADJUSTMENT VALVE TO CORRECT A CONCERN ABOUT THE ENGINE RUNNING IRREGULARLY. Read More »
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES. Read More »
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO VERIFY A RATTLING NOISE HEARD AT COLD START AND TO REPLACE BOTH UPPER CHAIN TENSIONERS OF BANK 1 AND BANK 2 WITH AN OPTIMIZED PART. Read More »
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES. Read More »
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V6 ENGINES. Read More »
A metallic whistling or grinding sound is heard from the engine compartment when th evehicle is at idle speed. The sound usually occurs when the engine is warm. The MIL is sporadically on due to DTCs being stored in the ECM. Read More »
This is an update to the November 3, 2015 communication where Volkswagen Group of America, Inc. issued a stop sale order for all 2013-2016 model year Audi vehicles equipped with a Gen II 3.0 liter V6 TDI engine. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 00 number 14-58 dated January 31, 2014. If a 2012 - 2016 Audi A8 L W12 arrives at an Audi dealership and requires diagnosis or repair, a Repair Authorization must be obtained. Read More »
Supersedes Technical Service Bulletin Group 27 number 14-23 dated April 24, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Optimized J931 control module software. Read More »
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-06 dated January 16, 2015. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-32 dated September 26, 2013. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 27 number 14-22 dated April 21, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Read More »
The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-43 dated December 21, 2012. If a 2012 - 2015 Audi A8 L W12 arrives at an Audi dealership and requires diagnosis or repair, a Repair Authorization must be obtained. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. Read More »
AUDI: ON SOME VEHICLES, THE ENGINE WARNING LIGHT SPORADICALLY WILL ILLUMINATE, OR HAVE REDUCED ENGINE PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, OR NOISE CAN BE HEARD COMING FROM ENGINE HIGH PRESSURE FUEL PUMPS 2. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-36 dated October 9, 2013. The customer reports that the engine warning light illuminates sporadically. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. Read More »
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
AUDI: SOME VEHICLES ENGINE WARNING LIGHT SPORADICALLY ILLUMINATES, WOULD HAVE REDUCED PERFORMANCE WITHOUT LOSS OF POWER/STALLING OR NOISE COMING FROM ENGINE COMPARTMENT DUE TO LOW SYSTEM VOLTAGE, AND NOT ENOUGH ON/OFF RATIO TO KEEP FUEL ... Read More »
The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Read More »
MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
This communication is to inform you of Update 23L9. On Audi A8 TDI manufactured within a specific period of time the idle speed may cause vibrations. Update the ECM software to the latest level. Read More »
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
Audi is releasing a software calibration update to the Approved Emissions Modification (AEM) to improve on-board diagnostics (OBD) monitoring of vehicle emissions systems and provide other improvements to the software used by the vehicle. Read More »
Audi is releasing a software calibration update to the Approved Emissions Modification (AEM) to improve on-board diagnostics (OBD) monitoring of vehicle emissions systems and provide other improvements to the software used by the vehicle. Read More »
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. Vehicles also include 2015 A3 Cabriolet and 2012 RS7, Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement Read More »
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement Read More »
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501. Read More »
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501. Read More »
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501. Read More »
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED. Read More »
The technical service bulletin is in regards to the MIL being on due to DTC P1B1C00 (coolant pump mechanical malfunction) being stored in the ECM. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. Read More »
MIL on (DTC P1B1C); message in information panel: "Coolant System: Fault Turn Off Engine" The condition is caused either a defect with the thermostat (in model year 2012 and 2013 vehicles) or The diagnostic software is incorrectly ... Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. Read More »
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-64 dated June 3, 2015. A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. Read More »
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM. Read More »
A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually only occurs when the engine is warm. The MIL is sporadically on. DTC P2279 and DTC P0507 are stored in the ECM. Read More »
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). Read More »
Supersedes Technical Service Bulletin Group 20 number 14-34 dated June 26, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
DTC P218100 will be stored if, after a specified air flow (warm-up phase), the measured engine temperature does not reach the value in the timing map. Read More »
Supersedes Technical Service Bulletin Group 00 number 13-55 dated October 21, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 20 number 14-32 dated March 21, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). Read More »
upersedes Technical Service Bulletin Group 20 number 14-31 dated January 9, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
The fuel metering valve of the high-pressure fuel pump is controlled by a specific on/off ratio. If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-44 dated October 22, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, ... Read More »
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. Read More »
On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. Read More »
This communication is to inform you of upcoming Update 24Z6. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger. Read More »
Supersedes Technical Service Bulletin Group 21 number 13-17 dated August 16, 2013. On 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger. Read More »
The crankcase breather is only connected to the bank 2 turbocharger inlet. Blow-by gases from the crankcase breather discolor the pipe (Figure 1). This is a normal condition. Read More »
On 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger. The crankcase breather is only connected to the bank 2 turbocharger inlet. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:OIL COOLER
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
Incorrect software calibration in the engine control module (ECM), J623, and transmission control module (TCM), J217. Customer may report feeling a slight hesitation or delay at 5-9 mph after accelerating from a stop. Read More »
The ECM software version is older than the specified software for this bulletin. Software improvement with more robust onboard diagnostics. Read More »
Software improvement with more robust onboard diagnostics. If ECM software is current or newer than below, this bulletin cannot be applied. Follow GFF instructions. Read More »
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-88 dated August 15, 2014. The MIL is on. DTC P218100 (Cooling System Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Customer states that engine overheats. No MIL. No related DTCs are stored. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. Read More »
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet. Read More »
This bulletin provides information regarding the replacement of the front muffler if vibrations are noticed in the seat or center arm rest. Read More »
While these types of noises could be attributed to a number of components in the vehicle, misaligned front exhaust hangers may be a contributing factor. Read More »
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, ... Read More »
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or ... Read More »
Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This communication instructs dealers to contact the Technical Assistance Center if they encounter a MIL on before performing the TDI emissions modification. - REVISED 12/17/18 to apply to 3.0L models and to remove 2.0L models. Read More »
This bulletin explains the extended emissions warranty for TDI vehicles modified under Campaign 23V4. The parts list was updated to include service numbers. Read More »
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Removed California DMV Tie-in Requirements Read More »
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement Read More »
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles. Read More »
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Revised legal approved copy. Read More »
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored. Read More »
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or ... Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually occurs when the engine is warm. The MIL is sporadically on due to DTCs being stored in the ECM. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AN ISSUE WITH THE OXYGEN SENSORS THAT CAUSES DTC P013E00 OR P014A00 TO BE STORED. Read More »
Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment. Read More »
This bulletin provides information regarding the replacement of the front muffler if vibrations are noticed in the seat or center arm rest. Read More »
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501. Read More »
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
Supersedes Technical Service Bulletin Group 20 number 15-45 dated May 6, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 20 number 14-43 dated December 19, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake ... Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-26 dated May 15, 2013. Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-69 dated March 6, 2014. The MIL is on. No start or rough running. DTCs are stored in the ECM. Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
The fuel metering valve of the high-pressure fuel pump is controlled by a specific on/off ratio. If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. Read More »
The fuel metering valve of the high-pressure fuel pump is controlled by a specific on/off ratio. If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. Read More »
The fuel metering valve of the high-pressure fuel pump is controlled by a specific on/off ratio. If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, ... Read More »
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, ... Read More »
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or ... Read More »
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or ... Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP
Supersedes Technical Service Bulletin Group 20 number 13-26 dated May 15, 2013. Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Read More »
The MIL is on due to a Fuel Rail/System Pressure Too Low DTC stored in the ECM. Drivability concerns such as hard starting/no starting are present. Fuel pump may be making a straining noise. Outside temperature is sub-freezing. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-69 dated March 6, 2014. The MIL is on. No start or rough running. DTCs are stored in the ECM. Read More »
The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be ... Read More »
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Read More »
AUDI: SOME VEHICLES ENGINE WARNING LIGHT SPORADICALLY ILLUMINATES, WOULD HAVE REDUCED PERFORMANCE WITHOUT LOSS OF POWER/STALLING OR NOISE COMING FROM ENGINE COMPARTMENT DUE TO LOW SYSTEM VOLTAGE, AND NOT ENOUGH ON/OFF RATIO TO KEEP FUEL ... Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
Beginning with MY2009, the filler necks of various TDI clean diesel vehicles were equipped with a misfueling guard (Figure 1). The guard minimizes the likelihood that fuel other than ultra-low sulfur diesel will be put into the vehicle. Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, ... Read More »
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, ... Read More »
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, ... Read More »
Supersedes Technical Service Bulletin Group 01 number 13-75 dated March 13, 2013. If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel ... Read More »
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or ... Read More »
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or ... Read More »
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or ... Read More »
If an Audi model year 2014 A8L TDI clean diesel (engine code CPNA) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is ... Read More »
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, ... Read More »
The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 39 number 14-14 dated May 5, 2014. A squealing, howling, or whistling noise may be heard coming from under the vehicle. Read More »
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner. Read More »
Supersedes Technical Service Bulletin Group 26 number 14-21 dated February 3, 2014. Various noises, such as humming, vibration, and/or rattling are heard coming from under the vehicle or from near the center console area. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. Read More »
Incorrect software calibration in the engine control module (ECM), J623, and transmission control module (TCM), J217. Customer may report feeling a slight hesitation or delay at 5-9 mph after accelerating from a stop. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-36 dated October 9, 2013. The customer reports that the engine warning light illuminates sporadically. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks ... Read More »
POWER TRAIN:MANUAL TRANSMISSION:COLUMN SHIFT ASSEMBLY
Supersedes Technical Service Bulletin Group 00 number 12-43 dated December 21, 2012. If a 2012 - 2015 Audi A8 L W12 arrives at an Audi dealership and requires diagnosis or repair, a Repair Authorization must be obtained. Read More »
An AdBlue message may appear in the instrument cluster either because there is a fault in the emission control system or because the system needs to be refilled. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-10 dated June 24, 2013. If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel ... Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow. Read More »
Supersedes Technical Service Bulletin Group 27 number 14-23 dated April 24, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Optimized J931 control module software. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-06 dated January 16, 2015. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. Read More »
DTC P174900 (Automatic transmission control module incorrect code) appears in the Transmission Control Module (TCM) after an SVM update. The self-coding function of the TCM may not complete during a software update. Read More »
Customer may report feeling a slight hesitation or delay at 5-9 mph after accelerating from a stop. Incorrect software calibration in the engine control module (ECM), J623, and transmission control module (TCM). Read More »
The self-coding function of the TCM may not complete during a software update. Incorrect coding in control module after software update (DTC P1749 stored in TCM) Read More »
Incorrect software calibration in the engine control module (ECM), J623, and transmission control module (TCM), J217. Customer may report feeling a slight hesitation or delay at 5-9 mph after accelerating from a stop. Read More »
Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 ... Read More »
This bulletin contains repair information for when the remote key has low range or the functions do not work. This is for all keys and there is no relevant DTCs stored. Read More »
This is a general communication notifying dealers that there is extended Warranty coverage available for the NVLD pressure switch for certain models and model years. This document details the terms of the warranty extension. Read More »
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored. Read More »
RUNNING GEAR: AUDI MAGNETIC RIDE - KNOCKING NOISES FROM REAR SHOCKS ON S3 (8V) AND TTS (FV) BRAKE SYSTEM: BRAKING NOISES - BASIC PRINCIPALS FOR DIAGNOSIS AND REPAIR. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 20 number 15-56 dated November 19, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 20 number 15-55 dated November 6, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM). Read More »
Supersedes Technical Service Bulletin Group 20 number 15-50 dated October 19, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM). Read More »
Supersedes Technical Service Bulletin Group 20 number 15-46 dated May 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
The MIL is on and/or glow plug light on. DTCs are stored in the ECM. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Read More »
The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
DTC P103200 (NOx sensor signal too high) is stored in the engine control module (ECM). Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-26 dated June 30, 2015. The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM). Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
The MIL is on. DTC P20E800 is stored in the ECM. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Software update is needed. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-87 dated May 18, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or ... Read More »
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". Read More »
Supersedes Technical Service Bulletin Group 94 number 15-60 dated February 12, 2015. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". Read More »
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". Read More »
Supersedes Technical Service Bulletin Group 20 number 14-41 dated October 9, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 01 number 14-84 dated July 28, 2014. MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 20 number 14-36 dated August 14, 2014. MIL on.DTC P310B is stored in the engine control module, J623 (address word 01), with symptom code 6183. Read More »
In certain operating conditions, a function in the internal thermal management system can increase the engine temperature. Updated engine control module (ECM) software. Read More »
The self-coding function of the TCM may not complete during a software update. Incorrect coding in control module after software update (DTC P1749 stored in TCM) Read More »
Incorrect software calibration in the engine control module (ECM), J623, and transmission control module (TCM), J217. Customer may report feeling a slight hesitation or delay at 5-9 mph after accelerating from a stop. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-32 dated September 26, 2013. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. Read More »
This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
Supersedes Technical Service Bulletin Group 27 number 14-21 dated February 11, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
Supersedes Technical Service Bulletin Group 27 number 14-22 dated April 21, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Read More »
Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. Read More »
Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module. Read More »
Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Read More »
The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. Read More »
Vibrations are felt at 1000 rpm and 3000 rpm. DTCs are stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of ... Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-16 dated November 27, 2013. After the camera control module, J928, has been replaced, the front image is upside down and cannot be changed. The calibration cannot be completed. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. Read More »
An AdBlue message may appear in the instrument cluster either because there is a fault in the emission control system or because the system needs to be refilled. Read More »
quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-79 dated March 20, 2013. MIL on. DTCs are stored in the engine control module (address word 01). Excess rattling (?diesel clatter?) coming from engine. Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. Read More »
This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. Read More »
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. Read More »
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-08 dated February 17, 2015. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. Read More »
The MIL is on due to a Fuel Rail/System Pressure Too Low DTC stored in the ECM. Drivability concerns such as hard starting/no starting are present. Fuel pump may be making a straining noise. Outside temperature is sub-freezing. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-51 dated January 3, 2014. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. Read More »
MIL on; (DTC P046100 - Fuel level sensor, circuit range/performance). MIL is on during normal driving conditions, city or highway at any speed. Read More »
ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS:ACCESORY POWER OUTLET/JACK/PORT/USB/SAE/CIGARETTE LIGHTER
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored. Read More »
The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level. There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective. Read More »
Effective immediately, the codes for the STP4 (2.0L TDI) and STP5 (3.0L TDI) actions will show the campaign code 23Q4 (2.0L TDI) and 23R8 (3.0L TDI) only on the Inventory Vehicle Open Campaign/Action Report. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. Read More »
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed ... Read More »
An AdBlue message may appear in the instrument cluster either because there is a fault in the emission control system or because the system needs to be refilled. Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive. Read More »
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive. Read More »
Audi is releasing a software calibration update to the Approved Emissions Modification (AEM) to improve on-board diagnostics (OBD) monitoring of vehicle emissions systems and provide other improvements to the software used by the vehicle. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR UPDATING THE SOFTWARE OF THE DOOR COMFORT SYSTEM CONTROL MODULES TO CORRECT AN ISSUE WITH THE LEFT OR RIGHT REAR DOOR SUNSHADE. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
Audi connect Gen1 and Gen2 systems: Differences and troubleshooting. The customer has a general concern related to Audi connect. Different features are included with different generations of the Audi connect system. Read More »
TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the ECM. New ECM software implemented to correct the condition. Read More »
MIL on (DTC P1B1C); message in information panel: "Coolant System: Fault Turn Off Engine" The condition is caused either a defect with the thermostat (in model year 2012 and 2013 vehicles) or The diagnostic software is incorrectly ... Read More »
The MIL is on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow. Read More »
Supersedes Technical Service Bulletin Group 20 number 15-52 dated October 28, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 20 number 15-48 dated October 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 20 number 15-47 dated August 5, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
The head-up display will not power on or does not work. After the next bus silence (for example, waiting five minutes after the driver side door is locked), the head-up display works correctly. Read More »
Engine warning lamp is illuminated. EPC lamp is illuminated. The engine runs irregularly. DTCs related to the cylinder on demand (COD) function are stored in the engine control module, J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-25 dated June 19, 2015. The MIL is on. DTC P20E800 (Reductant pressure too low) is stored in the engine control module. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-21 dated April 29, 2015. The MIL is on. DTC P046100 (Fuel level sensor circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Read More »
The MIL is on. DTC P20E800 is stored in the ECM. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Software update is needed. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-81 dated June 24, 2014. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM). Read More »
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or ... Read More »
The MIL is on. DTC P20FE00 (Reductant Metering Unit Performance) is stored in the engine control module (ECM). The ECM software version is older than the specified software for this bulletin. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
The self-coding function of the TCM may not complete during a software update. Incorrect coding in control module after software update (DTC P1749 stored in TCM) Read More »
Incorrect software calibration in the engine control module (ECM), J623, and transmission control module (TCM), J217. Customer may report feeling a slight hesitation or delay at 5-9 mph after accelerating from a stop. Read More »
Some vehicles may experience a limp home mode condition due to DPF soot accumulation which could cause the Malfunction Indicator Light (MIL) to come on. Update the ECM software to the latest level. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-78 dated October 31, 2013. Audi side assist deactivates or is sporadically inoperative. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-55 dated August 13, 2012. The most recent calls are not shown in the call lists of the vehicle. Call lists are not shown. The phone book (Directory) in the vehicle is not updated. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi ... Read More »
Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
The customer reports that the alarm goes off for no reason. The passenger door control module, J387 (address word 52), has software version 0273 ? only this version is affected. Read More »
This communication is to inform you of Update 23L9. On Audi A8 TDI manufactured within a specific period of time the idle speed may cause vibrations. Update the ECM software to the latest level. Read More »
This document conveys general information on the VAS tester brand software V19.48.00. The benefit is that after updating the VAS tester with this software version, you will no longer need to follow the Service Information work around ... Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light ... Read More »
TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Read More »
AUDI: THE VEHICLE LIGHTS MALFUNCTION MESSAGE MAY BE DISPLAYED ON THE DASHBOARD CLUSTER. THERE IS NO FAILURE. ALSO INCLUDED MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL S7 MY 2012-2014, MODEL RS7 MY 2014. Read More »
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". Read More »
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake ... Read More »
AUDI: 2014-2015 A8 : HEADLIGHT WARNING LIGHT SHOWING IN THE INSTRUMENT CLUSTER WHICH COMES FROM THE CONNECTOR IN HEADLIGHT NOT PROPERLY SEATED. *LJ Read More »
A headlight system warning may be illuminated in the instrument cluster. Diagnosis of the concern indicates that the headlight is at fault. Connector in the headlight is not properly seated. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
Supersedes Technical Service Bulletin Group 94 number 13-12 dated March 29, 2013. The headlight switch knob was designed with a normal position and a pushed-in position. This feature was designed to avoid injuries during a collision. Read More »
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. Read More »
On Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times in quick succession. This Update is in effect until removed. Read More »
This communication is to inform you of upcoming Update 68E3. On certain Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times ... Read More »
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
Supersedes Technical Service Bulletin Group 70 number 15-47 dated September 21, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
Supersedes Technical Service Bulletin Group 70 number 15-44 dated February 25, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
Supersedes Technical Service Bulletin Group 70 number 14-39 dated August 11, 2014. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Creaking noises can be heard from the A-pillar, dash panel, or windshield. The small lug on the centering pins of the windshield can cause the creaking noises. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
Supersedes Technical Service Bulletin Group 70 number 14-39 dated August 11, 2014. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is ... Read More »
While these types of noises could be attributed to a number of components in the vehicle, misaligned front exhaust hangers may be a contributing factor. Read More »
quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. Read More »
Supersedes Technical Service Bulletin Group 55 number 14-34 dated March 21, 2014. The movement-activated rear lid opening (also known as "Hands-free trunk release") is sporadically inoperative. Read More »
The movement-activated rear lid opening (also known as ? Hands-free trunk release? ) sporadically is inoperative. This feature is installed on A8 vehicles with Audi advanced key (PR No. 4I3) from CW 45/2011 production. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-62 dated January 9, 2012. The trunk cannot be unlocked with the button on the remote, with the button in the driver?s door panel, or with the handle on the lid of the trunk. Read More »
Supersedes Technical Service Bulletin Group 55 number 14-34 dated March 21, 2014. The movement-activated rear lid opening (also known as "Hands-free trunk release") is sporadically inoperative. Read More »
Supersedes Technical Service Bulletin Group 55 number 13-29 dated March 29, 2013. The movement-activated rear lid opening (also known as "Hands-free trunk release") is sporadically inoperative. Read More »
Supersedes Technical Service Bulletin Group 55 number 13-28 dated February 27, 2013. The movement-activated rear lid opening (also known as "Hands-free trunk release") sporadically is inoperative. Read More »
Supersedes Technical Service Bulletin Group 55 number 12-26 dated October 23, 2012. The movement-activated rear lid opening (also known as "Hands-free trunk release") sporadically is inoperative. Read More »
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph. Read More »
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when the user searches for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Supersedes Technical Service Bulletin Group 91 number 13-78 dated March 15, 2013. Adaptive Cruise Control (ACC) does not work. The message "ACC and braking guard: unavailable at this time. Read More »
Adaptive Cruise Control (ACC) does not work. The message "ACC and braking guard: unavailable at this time. No sensor vision" appears in the instrument cluster. DTC is logged in the distance regulation control module, J428 (address word 13). Read More »
FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA
Supersedes Technical Service Bulletin Group 96 number 13-78 dated October 31, 2013. Audi side assist deactivates or is sporadically inoperative. Read More »
Road lane markings are not detected or the Audi lane assist system is inoperative after the lane assist camera control module, J852, has been calibrated, the windshield has been replaced, or the air suspension level sensors have been ... Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition. Improved software for the comfort system central control module, J393 (address word 46) in production. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-04 dated July 22, 2015. The customer complains that the rearview camera image is not displayed on the MMI display. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-70 dated November 6, 2014. The overhead view camera system or one of its cameras does not work. DTCs are logged in the rearview camera system control module. Read More »
AUDI: SOME VEHICLES EXPERIENCE, INTERMITTENTLY, THE MMI DISPLAY FAILING TO DISPLAY REARVIEW CAMERA IMAGE DUE TO POSSIBLE WIRING HARNESS ISSUE. MODEL 2013-16 A4, A5, A8, Q3, Q5, Q7. *PE Read More »
Supersedes Technical Service Bulletin Group 90 number 12-31 dated July 16, 2012. Customer states all or part of the picture generated from the top view camera system has an unnatural hue. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
The overhead view camera system or one of its cameras does not work. DTCs are logged in the rearview camera system control module. DTCs for the affected camera may also be logged. Incorrect component. Read More »
One of the TopView cameras will not calibrate. For issues with the Front TopView camera image being upside down after replacing J928, please reference TSB 2035912, 91 Front TopView camera cannot be calibrated; picture appears upside down. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-16 dated November 27, 2013. After the camera control module, J928, has been replaced, the front image is upside down and cannot be changed. The calibration cannot be completed. Read More »
After the camera control module, J928, has been replaced, the front image is upside down and cannot be changed (Figure 1). The calibration cannot be completed. The coding of the camera control module is not completed correctly. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the ... Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage. Read More »
This communication is issued to remind dealers of the repair validation process for repair group 19. 2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 ... Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This communication instructs dealers to contact the Technical Assistance Center if they encounter a MIL on before performing the TDI emissions modification. - REVISED 12/17/18 to apply to 3.0L models and to remove 2.0L models. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This bulletin contains repair instructions for when the MIL is on and one of many DTCs is stored in relation to dylinder on demand function. Read More »
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles. Read More »
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries. Read More »
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward. Read More »
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has ... Read More »
Supersedes Technical Service Bulletin Group 96 number 14-85 dated July 24, 2014. The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin. Read More »
The 12V outlet compartment in the rear center console is disengaged, causing the compartment to come out or to not close into the console. The compartment was bumped or kicked while open, causing it to disengage. Read More »
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed. Read More »
While these types of noises could be attributed to a number of components in the vehicle, misaligned front exhaust hangers may be a contributing factor. Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-86 dated June 11, 2013. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. Read More »
quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. Read More »
On Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times in quick succession. This Update is in effect until removed. Read More »
On Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times in quick succession. This Update is in effect until removed. Read More »
This communication is to inform you of upcoming Update 68E3. On certain Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times ... Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
The movement-activated rear lid opening (also known as ? Hands-free trunk release? ) sporadically is inoperative. This feature is installed on A8 vehicles with Audi advanced key (PR No. 4I3) from CW 45/2011 production. Read More »
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Removed California DMV Tie-in Requirements Read More »
Supersedes Technical Service Bulletin Group 57 number 11-54 dated August 18, 2011. Audi advanced key (keyless entry) is inoperative on all doors, but the engine can be started with the keyless starting system (keyless go). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-28 dated March 6, 2014. MMI freezes or crashes and restarts when telephone address book is searched. Read More »
Supersedes Technical Service Bulletin Group 55 number 14-34 dated March 21, 2014. The movement-activated rear lid opening (also known as "Hands-free trunk release") is sporadically inoperative. Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear ... Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 01 number 15-08 dated February 17, 2015. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. Read More »
The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 20 number 14-32 dated March 21, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Left and/or right rear door sunshade may be stuck or inoperative. Due to a faulty signal, the door control unit does not activate the roller blind. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a ... Read More »
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth ... Read More »
After the camera control module, J928, has been replaced, the front image is upside down and cannot be changed (Figure 1). The calibration cannot be completed. The coding of the camera control module is not completed correctly. Read More »
Supersedes Technical Service Bulletin Group 26 number 11-03 dated June 29, 2011. There is an AdBlue-related message displayed in the instrument cluster. MIL may or may not be illuminated. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-86 dated June 11, 2013. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Road lane markings are not detected or the Audi lane assist system is inoperative after the lane assist camera control module, J852, has been calibrated, the windshield has been replaced, or the air suspension level sensors have been ... Read More »
Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. Read More »
Supersedes Technical Service Bulletin Group 55 number 12-26 dated October 23, 2012. The movement-activated rear lid opening (also known as "Hands-free trunk release") sporadically is inoperative. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-64 dated October 25, 2012. CD or DVD disks do not automatically change from one to the next in the external CD or DVD changer. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION. Read More »
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-10 dated August 25, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or ... Read More »
Supersedes Technical Service Bulletin Group 91 number 15-90 dated June 5, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or ... Read More »
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle's actual location or direction of travel for a long period of time (often as long as 10 minutes). Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear ... Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
The customer complains about GPS navigation issues that may be antenna-related. No DTC entry is logged. This bulletin should be performed before any other bulletins that cover specific customer complaints. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth ... Read More »
The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s). Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. Read More »
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance. Read More »
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles. Read More »
This is a general communication notifying dealers that there is extended Warranty coverage available for the exhaust gas temperature sensor for certain models and model years. This document details the terms of the warranty extension. Read More »
This is a general communication notifying dealers that there is extended Warranty coverage available for the NVLD pressure switch for certain models and model years. This document details the terms of the warranty extension. Read More »
THIS SPECIAL NOTICE IS TO INFORM DEALERS TO RETURN ALL 07P-121-115-C /07P-198-210 AND ONLY ORDER PART NUMBER07P-121-115-E / 07P-198-210-A GOING FORWARD. Read More »
This is an email detailing the Audi TDI Goodwill Package that is extended to 3.0L TDI Customers. The email also included the dealer information letter, dealer FAQs, and sample customer letters. Read More »
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Read More »
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
The vehicle horn sounds abnormal or is inoperative. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. Read More »
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. Read More »
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Some vehicles may experience a limp home mode condition due to DPF soot accumulation which could cause the Malfunction Indicator Light (MIL) to come on. This Update is in effect until removed. Read More »
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Audi of America is requesting your cooperation in supplying us with the technical information vital to the successful launch of the MY14 TDI clean diesel vehicles. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-68 dated November 12, 2012. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. Read More »
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options. Read More »
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, ... Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Read More »
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. Read More »
On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. Read More »
This communication is to inform you of upcoming Update 87D9. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
