Technical Service Bulletins (TSBs) for the 2011 Touareg Hybrid are official communications between Volkswagen & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Technical Bulletin: Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time causing restrictions. Read More »
When diagnosis on the above engine leads to the testing of the N75, please refer to the picture below. The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not. Read More »
VOLKSWAGEN: ACTIVATED CHARCOAL FILTER SYSTEM, SOLENOID VALVE AND PERFORMING GFF FUNCTION TEST A VACUUM CHECK ON CANISTER PURGE VALVE N80 ARE ESSENTIAL TO DIAGNOSE PROPER OPERATION. MODEL 2009-14 ALL BUT ROUTAN. Read More »
In SAGA, the time units for the Volkswagen DoubleCheck labor operation were reduced in error from 50 time units to 30 time units during the system update posted on July 4th. Read More »
VOLKSWAGEN: ALL MODELS EXPERIENCE THE TIMING CHAIN SLIPPING, RATTLING NOISES OF THE ENGINE AFTER STARTING, AND ENGINE FAILS TO START. 2008-13 ALL MODELS. *PE Read More »
For an upcoming campaign that will include all MY09-14 TDI (CBEA/CJAA) vehicles, we need to test the SVM3339 code in 200 vehicles of various model-years and engine/transmission combinations. Read More »
After a cold start, the engine coolant temperature gauge will slowly rise to approximately 190? F. When the F265 mapped thermostat opens, the gauge may drop by approximately 60? F before again rising to 190? F. Read More »
When servicing the timing chain sprocket or removing the vibration damper, be aware that one bolt holds both the vibration damper (harmonic balancer) and the crankshaft timing chain sprocket to the crankshaft. Read More »
VOLKSWAGEN: CERTAIN MODEL YEAR VEHICLES ARE EXPERIENCING ENGINE NOT STARTING, MAKING A RATTLING NOISE WHEN ENGINE HAS STARTED, TIMING CHAIN KEEPS SLIPPING AND EXHAUST LIGHT COMES ON. *PE Read More »
VOLKSWAGEN: MALFUNCTION LIGHT IS ON AND THERE IS NOISE WITH THE ENGINE RUNNING ROUGH. MULTIPLE TROUBLE CODES POSSIBLY STORED. ALL MODELS 2008-2012. *RM Read More »
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear. Read More »
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear. Read More »
This special notice is to inform dealers to return all part numbers listed in the document. Only superseded part numbers to be ordered going forward. Read More »
VOLKSWAGEN:EVAPORATIVE (EVAP) EMISSION SYSTEM, DIAGNOSTIC TROUBLE CODE DIAGNOSIS. REVISED PROCEDURE DEVELOPED TO TEST EVAP SYSTEM WITHOUT FUEL CAP. *JS Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
This special notice is to inform dealers to return all part numbers listed in the document. Only superseded part numbers to be ordered going forward. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
Because Volkswagen supports the development and use of renewable fuels (such as biodiesel fuel blends), customers with certain 2009-2015 MY Volkswagen TDI? Clean Diesel Engine vehicles registered in the State of Minnesota only will ... Read More »
Carefree Maintenance Coverage for Interim Oil Changes for Certain 2009 ? 2015 MY Volkswagen TDI? Clean Diesel Engine Vehicles Registered in the State of Minnesota Only (US Dealers Read More »
When the Navigation RNS 850/510/315 is in 3D mode, the top portion of the screen may not display streets. This line represents the horizon and is a normal operation of system. No repairs should be made. Read More »
VOLKSWAGEN: ON SOME VEHICLES, LOW FUEL STORED IN ECM PRESSURE, ENGINE WOULD CRANK BUT NOT START LONG PERIODS WITHOUT DRIVING, MAY RUN ROUGH AND/OR MIL ON. ALL MODELS 2008-2013. *PE Read More »
VOLKSWAGEN DEALERSHIP COMMUNICATION: This document announced a warranty Volkswagen extension program to cover the High Pressure Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles. Read More »
VOLKSWAGEN DEALERSHIP COMMUNICATION: Volkswagen announced a warranty extension program to cover the High Pressure Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles Read More »
Because Volkswagen supports the development and use of renewable fuels (such as biodiesel fuel blends), customers with certain 2009-2015 MY Volkswagen TDI? Clean Diesel Engine vehicles registered in the State of Minnesota only will ... Read More »
Carefree Maintenance Coverage for Interim Oil Changes for Certain 2009 ? 2015 MY Volkswagen TDI? Clean Diesel Engine Vehicles Registered in the State of Minnesota Only (US Dealers Read More »
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear. Read More »
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear. Read More »
VOLKSWAGEN: ON SOME VEHICLES, LOW FUEL STORED IN ECM PRESSURE, ENGINE WOULD CRANK BUT NOT START LONG PERIODS WITHOUT DRIVING, MAY RUN ROUGH AND/OR MIL ON. ALL MODELS 2008-2013. *PE Read More »
Incorrect torque converter or flywheel/flexplate installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. Read More »
For an upcoming campaign that will include all MY09-14 TDI (CBEA/CJAA) vehicles, we need to test the SVM3339 code in 200 vehicles of various model-years and engine/transmission combinations. Read More »
This bulletin provides a procedure to determine ?repair? versus ?replacement? of an automatic transmission. This procedure is to be used ?After? the transmission has been removed from the vehicle. Read More »
When servicing the timing chain sprocket or removing the vibration damper, be aware that one bolt holds both the vibration damper (harmonic balancer) and the crankshaft timing chain sprocket to the crankshaft. Read More »
Technical Bulletin: Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time causing restrictions. Read More »
When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended. Read More »
The DLC is intended for use with diagnostic scan tools and by emissions testing stations. However, aftermarket devices (i.e., drive data recorders) that connect to the DLC have now become available. Read More »
When replacing the complete vehicle lock set (all vehicle keys and lock cylinders) for any reason, be aware that the ?Adapt keys? test plan will not allow the new keys to adapt to the vehicle. Read More »
To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Read More »
To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Read More »
If key blade is found to stick or bind when opening or closing, check position of roll pin that secures key blade to mechanism. If roll pin is sticking out on either side (as shown below), do not replace key. Read More »
Tech Tips (Instrument Cluster Production Mode): During PDI, or after installation of a replacement cluster, ?Pro? may be displayed in place of the odometer. The high beam indicator may be flashing in the instrument cluster as well. Read More »
Quick Reference of vehicle concerns. Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated Read More »
The indicator lamp in the I.P. for washer fluid remains illuminated and the washer reservoir is full. Validate the washer reservoir is full with the proper washer solvent (G-052-164). Read More »
The indicator lamp in the I.P. for washer fluid remains illuminated and the washer reservoir is full. Validate the washer reservoir is full with the proper washer solvent (G-052-164). Read More »
The indicator lamp in the I.P. for washer fluid remains illuminated and the washer reservoir is full. Validate the washer reservoir is full with the proper washer solvent (G-052-164). Read More »
The indicator lamp in the I.P. for washer fluid remains illuminated and the washer reservoir is full. Validate the washer reservoir is full with the proper washer solvent (G-052-164). Read More »
Reporting procedure for A/C compressor replacement regardless of the reason for failure. Update to model year applicability and new warranty GFF labor operation number Read More »
Cleaning of Heating and Ventilation system, Updated to include additional model year applicability and cost of cleaning solution in warranty table. Read More »
To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Read More »
When replacing the Air Conditioning compressor it is necessary to flush the entire system to remove all the PAG oil. Replacement AC compressors come with a full charge of oil. Read More »
The use of tire dressing gives your tires that shiny finish that completes the image of a clean (new) vehicle. There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Read More »
The use of tire dressing gives your tires that shiny finish that completes the image of a clean (new) vehicle. There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Read More »
When replacing the radio on a 2010 ? 2011 vehicle equipped with a Premium 8 (RCD 510) radio with part number ending in the suffix ?AC? (1K0 035 180 AC), if the replacement part has a suffix ?AF?, make sure that online coding is performed. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward. Read More »
This document contains the VW Elsa Newsletter that contains a general overview of wiring diagrams updates, ElsaPro infomedia icons grayed out, workshop equipment tool storage application, technical bulletins, pending service solutions, ... Read More »
When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended. Read More »
When replacing the complete vehicle lock set (all vehicle keys and lock cylinders) for any reason, be aware that the ?Adapt keys? test plan will not allow the new keys to adapt to the vehicle. Read More »
If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order. If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist. Read More »
If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order. If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist. Read More »
In SAGA, the time units for the Volkswagen DoubleCheck labor operation were reduced in error from 50 time units to 30 time units during the system update posted on July 4th. Read More »
"Touareg Perfect Delivery Inspection (PDI) - Technician and Detailer Inspections: A checklist to insure a customer receives a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has ... Read More »
Tech Tips (Bluetooth Compatibility): This document informs of the web address that can be used to check Bluetooth compatibility for all 2011, and newer vehicles, as well as 2010 Routan Read More »
When replacing the radio on a 2010 ? 2011 vehicle equipped with a Premium 8 (RCD 510) radio with part number ending in the suffix ?AC? (1K0 035 180 AC), if the replacement part has a suffix ?AF?, make sure that online coding is performed. Read More »
For concerns of navigation inaccuracy, with or without antenna fault codes, begin by checking the number of received satellites in the area of the concern. Read More »
When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended. Read More »
When pairing an Android phone to the Bluetooth system, a few extra steps may be necessary. Follow the instructions below to pair the phone: Read More »
This document contains the VW Elsa Newsletter that contains a general overview of wiring diagrams updates, technical bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions. Read More »
This document contains the VW Elsa Newsletter that contains a general overview of wiring diagrams updates, ElsaPro infomedia icons grayed out, workshop equipment tool storage application, technical bulletins, pending service solutions, ... Read More »
VOLKSWAGEN DEALERSHIP COMMUNICATION: This document announced a warranty Volkswagen extension program to cover the High Pressure Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles. Read More »
VOLKSWAGEN DEALERSHIP COMMUNICATION: Volkswagen announced a warranty extension program to cover the High Pressure Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles Read More »
VOLKSWAGEN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. AN EXTENSION WARRANTY, WITH SPECIFIC CONDITIONS, 10 YRS OR 120,000 MILES,WHICHEVER IS FIRST, HAS BEEN ISSUED FOR EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL ... Read More »
TOUAREG Perfect Delivery Inspection (PDI) - Technician and Detailer Inspections: A checklist to insure a customer receives a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has ... Read More »
"Touareg Perfect Delivery Inspection (PDI) - Technician and Detailer Inspections: A checklist to insure a customer receives a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has ... Read More »
We would like to inform you that the FAQ for Service Action 20T8 has been revised to include additional information for dealers to share with customers about the misfueling guard. Read More »
Statement referring to TB 2043893 removed. To include additional models and model year applicability. A.C. Compressor Replacement, GFF Required Regardless of Concern and Flush Requirement Read More »
VOLKSWAGEN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. AN EXTENSION WARRANTY, WITH SPECIFIC CONDITIONS, 10 YRS OR 120,000 MILES,WHICHEVER IS FIRST, HAS BEEN ISSUED FOR EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL ... Read More »
To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Read More »
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear. Read More »
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear. Read More »
