Technical Service Bulletins (TSBs) for the 2015 MAZDA6 are official communications between Mazda & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and ... Read More »
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure. Read More »
Some customers may have a concern of a loose steering wheel. If a customer reports a loose steering wheel and the lock bolt is found to be loose, DO NOT simply re-tighten the steering wheel. Follow the steps below in the Repair Procedure. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and ... Read More »
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
Some customers may complain about a vibration that is felt through the floor, seat and/or steering wheel while driving under moderate acceleration, at speeds of approx. 25 - 30 mph (40 - 50 km/h). Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. Read More »
SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and ... Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance.This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. Read More »
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3? EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE. Read More »
Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, ... Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (1). This may be caused by the dust boot having insufficient resistance to the cold. Read More »
Some customers may complain about a vibration that is felt through the floor, seat and/or steering wheel while driving under moderate acceleration, at speeds of approx. 25 - 30 mph (40 - 50 km/h). Read More »
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
Creaking Noise From Front Lower Control Arm Bushings Some vehicles may exhibit a creaking noise from under the front of the vehicle when driving over bumps. The noise occurs at approx. Read More »
BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
SOME VEHICLES MAY EXHIBIT A CHIRP/CLUNK TYPE NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE. Read More »
SOME VEHICLES MAY EXHIBIT A CHIRP/CLUNK TYPE NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
When the engine is started for the first time after parking overnight in cold weather (below freezing), some vehicles may exhibit the check engine light on with DTC P0451 (fuel tank pressure sensor: sensor characteristic malfunction) ... Read More »
IN CERTAIN CONDITIONS, SMART CITY BRAKE SUPPORT (SCBS) MAY OPERATE UNINTENTIONALLY. THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE. Read More »
IN CERTAIN CONDITIONS, SMART CITY BRAKE SUPPORT (SCBS) MAY OPERATE UNINTENTIONALLY. THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE. Read More »
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY ... Read More »
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY ... Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
Some vehicles may exhibit oil residue on the engine front cover from seepage around the joint portion (A) between the cylinder block and head. It becomes very noticable with dust adhesion. Read More »
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Read More »
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
Some 2012-2016 Mazda3s, 2013-2015 CX-5s and 2014-2015 Mazda6s may experience the Check Engine Light ON with DTC P0101 and/or P061B and/or driveability problem after reprogramming the PCM using IDS versions 105.02 to 105.04. Read More »
SOME VEHICLES MAY EXPERIENCE AN ENGINE THAT RUNS ROUGH AND THE CHECK ENGINE LIGHT ON WITH DTCS P0201 AND P0204 OR P0202 AND P0203.NOTE:ENGINE MISFIRE RELATED DTCS (P0301, P0302, P0303, P0304) ARE USUALLY STORED AT THE SAME TIME. Read More »
THERE IS A CONCERN THAT SOME WATER PUMPS ARE BEING REPLACED THAT ARE NOT FAULTY, DUE TO SIGNS OF A VERY SMALL COOLANT LEAK FROM THE BLEED HOLE. Read More »
SOME VEHICLES MAY EXPERIENCE A LACK OF ENGINE POWER/ROUGH IDLING AND THE CHECK ENGINE LIGHT ON WITH ONE OR MORE OF THE MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. Read More »
IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. Read More »
IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. Read More »
WHEN THE ENGINE IS STARTED FOR THE FIRST TIME AFTER PARKING THE VEHICLE OVERNIGHT IN COLD CONDITIONS (BELOW 32 DEGREES FAHRENHEIT / 0 DEGREES CELSIUS), SOME VEHICLES MAY EXHIBIT A ROUGH IDLE AND/OR THE CHECK ENGINE LIGHT ON WITH ANY OF ... Read More »
WHEN THE ENGINE IS STARTED FOR THE FIRST TIME AFTER PARKING THE VEHICLE OVERNIGHT IN COLD CONDITIONS (BELOW 32 DEGREES FAHRENHEIT / 0 DEGREES CELSIUS), SOME VEHICLES MAY EXHIBIT A ROUGH IDLE AND/OR THE CHECK ENGINE LIGHT ON WITH ANY OF ... Read More »
SOME VEHICLES MAY EXPERIENCE A LACK OF ENGINE POWER/ROUGH IDLING AND THE CHECK ENGINE LIGHT ON WITH ONE OR MORE OF THE MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. Read More »
WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING THE M-MDS HAS BEEN DISCONTINUED FOR SOME MODELS. INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS. Read More »
THE 2016 CX-9 WITH THE SKYACTIV?-G 2.5T ENGINE REQUIRES A UNIQUE OIL FILTER (PY8W-14-302) WHICH IS NOT INTERCHANGEABLE WITH OTHER SKYACTIV? OIL FILTERS. THE UNIQUE OIL FILTER CAN BE IDENTIFIED WITH TWO WHITE BANDS AS SHOWN BELOW. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITH-OUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). Read More »
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. ? P0015:00 - EXHAUST CMP TIMING OVER-RETARDED ? P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE ... Read More »
FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. ? P0015:00 - EXHAUST CMP TIMING OVER-RETARDED ? P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE ... Read More »
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. ? P0015:00 - EXHAUST CMP TIMING OVER-RETARDED ? P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE ... Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITHOUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). Read More »
FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Read More »
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. This noise is a normal engine operation for improved exhaust gas emissions. Read More »
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
Some customers may expierience one or more of the following: ??A?A? intermittent no start ??A?A? engine stall ??A?A? many DTC's stored ??A?A? no communication with the PCM. This may be caused by a poor C-11 or C-12 electrical connection. Read More »
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). Read More »
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
Some vehicles may exhibit oil residue on the engine front cover from seepage around the joint portion (A) between the cylinder block and head. It becomes very noticable with dust adhesion. Read More »
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded, P0524:00 - Engine oil pressure too low. Read More »
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely ... Read More »
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit/0 degrees Celsious). Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
When the engine is started for the first time after parking overnight in cold weather (below freezing), some vehicles may exhibit the check engine light on with DTC P0451 (fuel tank pressure sensor: sensor characteristic malfunction) ... Read More »
Unusual engine noise after a cold engine start. Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES ?0? WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK. Read More »
SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES ?0? WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK. Read More »
The SKYACTIV?-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV? oil filters. The unique oil filter can be identified with two white bands as shown below. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some vehicles may exhibit one of the following concerns: ??A?A? Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h) ??A?A? Hard to shift into 3rd, 4th, 5th, and/or ... Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. Read More »
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration. Read More »
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, ... Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h) Hard to shift into 3rd, 4th, 5th, and/or 6th gear ... Read More »
THE NEW SKYACTIV-DRIVE FW6A-EL AT USES ?AUTOMATIC TRANSMISSION FLUID (ATF) TYPE: FZ?. ONLY USE ?ATF-FZ? TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME CUSTOMERS MAY FIND IT DIFFICULT OR HARD TO MOVE THE A/T SHIFT LEVER. WHEN THE DRIVER OR FRONT PASSENGER?S LEG CONTACTS THE CENTER CONSOLE, LATERAL FORCE (A) MAY DEFORM THE INDICATOR SLIDER (B), CAUSING THE SLIDER EDGE TO CONTACT THE ... Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
Some customer using ??A???A???A?Flexible??A???A???A? setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
Some 2012-2016 Mazda3s, 2013-2015 CX-5s and 2014-2015 Mazda6s may experience the Check Engine Light ON with DTC P0101 and/or P061B and/or driveability problem after reprogramming the PCM using IDS versions 105.02 to 105.04. Read More »
Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITHOUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: ? SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) ? HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR ... Read More »
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: ? SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) ? HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR ... Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of ... Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
i-ELOOP Battery Service Information: This service information provides basic Q-85/T-110 battery handling procedures. Complete service information can be found in MGSS online or Workshop Manual (section 13-17). Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
Some customers may expierience one or more of the following: ??A?A? intermittent no start ??A?A? engine stall ??A?A? many DTC's stored ??A?A? no communication with the PCM. This may be caused by a poor C-11 or C-12 electrical connection. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
Some customer using ??A???A???A?Flexible??A???A???A? setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
MAZDA MOBILE START (MMS) APP ERROR MESSAGE INSTALLED ON ANDROID DEVICES: Customers may get an error message "Device no longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Read More »
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging. Read More »
Fctry MESSASGE DISPLAYED after instrument cluster replacement. After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Read More »
Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
SOME VEHICLES MAY HAVE DTC C1001:92 STORED IN MEMORY. DTC C1001:92 SETS AS A PAST RECORD FOR LOW VISIBILITY OF THE FORWARD SENSING CAMERA (FSC). IT DOES NOT MEAN THERE IS AN ACTUAL FSC DEFECT. Read More »
WHEN REPROGRAMMING A CONTROL MODULE, ALWAYS USE THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE. IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY. Read More »
OVER THE PAST TWO WEEKS, AN INCREASING NUMBER OF IPHONE SE EARLY ADOPTERS HAVE REPORTED AUDIO ISSUES WITH BLUETOOTH PHONE CALLS WHEN THE SMARTPHONE IS PAIRED WITH A VEHICLE OR WIRELESS HEADSET. Read More »
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
This service information provides basic Q-85/T-110 battery handling procedures. Complete service information can be found in MGSS online or Workshop Manual (section 13-17). Read More »
THIS SERVICE INFORMATION PROVIDES BASIC Q-85/T-110 BATTERY HANDLING PROCEDURES. COMPLETE SERVICE INFORMATION CAN BE FOUND IN MS3 ONLINE OR WORKSHOP MANUAL (SECTION 01-17). Read More »
THIS SERVICE INFORMATION PROVIDES BASIC Q-85/T-110 BATTERY HANDLING PROCEDURES. COMPLETE SERVICE INFORMATION CAN BE FOUND IN MS3 ONLINE OR WORKSHOP MANUAL (SECTION 01-17). Read More »
THIS SERVICE INFORMATION PROVIDES BASIC Q-85/T-110 BATTERY HANDLING PROCEDURES. COMPLETE SERVICE INFORMATION CAN BE FOUND IN MS3 ONLINE OR WORKSHOP MANUAL (SECTION 01-17). Read More »
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
SOME VEHICLES MAY EXPERIENCE A LACK OF ENGINE POWER/ROUGH IDLING AND THE CHECK ENGINE LIGHT ON WITH ONE OR MORE OF THE MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is? 2017 Mazda North American Operations, U.S.A. Read More »
Fctry MESSASGE DISPLAYED after instrument cluster replacement. After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Read More »
Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
MAZDA: SOME VEHICLES ARE EXPERIENCING AN ILLUMINATION OF MASTER WARNING LIGHT AND CHARGING SYSTEM WARNING LIGHT AND INSTRUMENT CLUSTER INFORMATION DISPLAYING, WHILE DRIVING, I-ELOOP INSPECTION IS REQUIRED. MODEL 2014-2015 MAZDA3, MAZDA6. Read More »
Upgrade your PCs to IDS version 109.00 and 109.01 from the previous version. NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108. Read More »
Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified. Read More »
IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version. Read More »
Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. Read More »
Some 2012-2016 Mazda3s, 2013-2015 CX-5s and 2014-2015 Mazda6s may experience the Check Engine Light ON with DTC P0101 and/or P061B and/or driveability problem after reprogramming the PCM using IDS versions 105.02 to 105.04. Read More »
Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging. Read More »
Some vehicles may exhibit navigation unit that cannot read out SMS (Short Messages Service) or does not operate properly after reading SMS. These concerns may be caused by problems with the Bluetooth Unit software. Read More »
CUSTOMERS THAT ARE REGISTERED WITH TOMTOM TO UPDATE THEIR MAZDA TOMTOM SYSTEM (USING TOMTOM HOME SOFTWARE) MAY HAVE RECENTLY RECEIVED THIS E-MAIL: PLEASE NOTE THAT THIS IS NOT AN OPERATING SYSTEM UPDATE (AKA FIRMWARE), THIS IS AN UPDATE ... Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. Read More »
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY. THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. Read More »
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).?NAVIGATION SYSTEM FREEZES. Read More »
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).?NAVIGATION SYSTEM FREEZES. Read More »
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER).? VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. Read More »
Some vehicles may exhibit excessive noise when operating either front power seat forward or backward. The noise may be caused by cable vibration, which transmits power from the motor to the gears. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some customers may complain that the headlights are not as bright as they had previously been. This is caused by a dulled headlight reflector in the front combination light. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT IMPROPER OPERATION OF THE AUTO-DIMMING MIRROR. THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). Read More »
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
Take caution when cleaning plastic headlight lenses. Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Read More »
WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT OR REAR COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMPTOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE ... Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
Some customers may complain that the headlights are not as bright as they had previously been. This is caused by a dulled headlight reflector in the front combination light. Read More »
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
Some vehicles may exhibit the cushion tape (1) attached to the front end of dashboard coming off and showing at the base of the windshield. Read More »
Some vehicles may exhibit the cushion tape (1) attached to the front end of dashboard coming off and showing at the base of the windshield. Read More »
CAUTION: DO NOT attempt any repair of the windshield damaged by stone chipping/cracks at the area in front of the Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead. Read More »
Some vehicles may exhibit wind noise at rear door quarter glass when driven at high speeds. This is caused by air leakage from the gap between rear sash molding, rear door glass run channel, rear door glass guide and rear door quarter ... Read More »
SOME VEHICLES MAY EXHIBIT A WIND NOISE FROM THE DOOR WINDOW EDGE(S), WHILE DRIVING. THE WIND NOISE IS MOST PRONOUNCED AT APPROXIMATELY 50 MPH (81 KM/H) ON A SMOOTH ROAD. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
When the engine is started for the first time after parking overnight in cold weather (below freezing), some vehicles may exhibit the check engine light on with DTC P0451 (fuel tank pressure sensor: sensor characteristic malfunction) ... Read More »
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit/0 degrees Celsious). Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
Some vehicles may exhibit the cushion tape (1) attached to the front end of dashboard coming off and showing at the base of the windshield. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
Some vehicles may experience unusual noise coming from inside the front door panel when playing the audio system. This is caused by the damper coming off the speaker frame due to corrosion on the speaker back frame. Read More »
SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. Read More »
SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. Read More »
Beginning with the CX-5 and Mazda6 models, grip type front and rear stabilizer bushings have been incorpo-rated for noise prevention purposes. Read More »
CORROSION AROUND SPOT WELDS IN TRUNK OPENING. SOME VEHICLES MAY EXHIBIT CORROSION AROUND THE SPOT WELDS IN TRUNK OPENING UNDER THE REAR WINDOW. THIS IS CAUSED BY INSUFFICIENT PAINT THICKNESS AT THE SPOT WELDS. Read More »
STAINS FOUND ON PAINT DURING PDI SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. Read More »
WHITE DOOR ARMREST(S) PINK DISCOLORATION. SOME CUSTOMERS MAY COMPLAIN ABOUT A WHITE DOOR ARMREST(S) PINK DISCOLORATION. THE DISCOLORED ARMREST DOES NOT MATCH THE OTHER WHITE PARTS OF THE DOOR PANEL. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. Read More »
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
Some vehicles may exhibit wind noise at rear door quarter glass when driven at high speeds. This is caused by air leakage from the gap between rear sash molding, rear door glass run channel, rear door glass guide and rear door quarter ... Read More »
Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2014-2016 Mazda6 vehicles produced from October 25, 2012 through January 30, 2015. Read More »
WHITE DOOR ARMREST(S) PINK DISCOLORATION. SOME CUSTOMERS MAY COMPLAIN ABOUT A WHITE DOOR ARMREST(S) PINK DISCOLORATION. THE DISCOLORED ARMREST DOES NOT MATCH THE OTHER WHITE PARTS OF THE DOOR PANEL. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT A WHITE DOOR ARMREST(S) PINK DISCOLORATION. THE DISCOLORED ARMREST DOES NOT MATCH THE OTHER WHITE PARTS OF THE DOOR PANEL. REPLACE ALL 4 DOOR PANELS. Read More »
SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. Read More »
SOME CUSTOMERS MAY HAVE A CONCERN WITH THE TOP EDGE OF THE REAR DOOR WEATHERSTRIP (A) DETACHED (COMING OFF / FALLING OFF) FROM FASTENER (B). Read More »
SOME VEHICLES MAY EXHIBIT A WIND NOISE FROM THE DOOR WINDOW EDGE(S), WHILE DRIVING. THE WIND NOISE IS MOST PRONOUNCED AT APPROXIMATELY 50 MPH (81 KM/H) ON A SMOOTH ROAD. Read More »
SOME VEHICLES MAY EXHIBIT A CONDITION THAT WATER ENTERS INTO THE TRUNK LID LIGHT WHILE WASHING THE VEHICLE WITH HIGH PRESSURE. WATER MAY ENTER THROUGH THE TRUNK LID LIGHT GASKET AND THE BODY PANEL. Read More »
SOME VEHICLES MAY EXHIBIT A CONDITION THAT WATER ENTERS INTO THE TRUNK LID LIGHT WHILE WASHING THE VEHICLE WITH HIGH PRESSURE. WATER MAY ENTER THROUGH THE TRUNK LID LIGHT GASKET AND THE BODY PANEL. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OF THE FOLLOWING SYMPTOMS WHEN THE VEHICLE IS STOPPED AND THE TRANSMISSION IS IN D RANGE: ? AN INTERMITTENT HIGH ENGINE IDLE SPEED. ? AN INTERMITTENT ENGAGEMENT SHOCK. ? AN INTERMITTENT FORWARD LURCH. Read More »
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
This service bulletin illustrates the conditions when a TPMS warning light may illuminate, why it illuminated and how to properly initialize the system. Read More »
Customer complaints have been reported where the TPMS warning light is unnecessarily illuminated because the TPMS initialization was not performed correctly before customer delivery. Read More »
SOME MAZDA6 VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
AFTER PERFORMING RECALL CAMPAIGN 8014J, OR THE VEHICLE VIN IS NOT APPLICABLE TO 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE ... Read More »
AFTER PERFORMING RECALL CAMPAIGN 8014J, OR THE VEHICLE VIN IS NOT APPLICABLE TO 8014J, SOME VEHICLES MAY EXPE-RIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE ... Read More »
AFTER PERFORMING RECALL CAMPAIGN 8014J, OR THE VEHICLE VIN IS NOT APPLICABLE TO 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE ... Read More »
AFTER PERFORMING RECALL CAMPAIGN 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
SOME AUTOMOTIVE CLEANING PRODUCTS CONTAIN STRONG ACID OR ALKALI. WHEN THESE TYPES OF CLEANERS ARE USED TO CLEAN THE WHEELS ON MAZDA VEHICLES, THE CHEMICALS CONTENTS PENETRATE THE CLEAR COATING OF THE WHEEL SURFACE AND DAMAGE THE PAINT ... Read More »
SOME VEHICLES MAY EXHIBIT A GROAN TYPE NOISE FROM THE FRONT WHEEL HUB BEARING WHILE DRIVING AT HIGH SPEED OR WHEN CORNERING. THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION. Read More »
SOME VEHICLES MAY EXHIBIT A GROAN TYPE NOISE FROM THE FRONT WHEEL HUB BEARING WHILE DRIVING AT HIGH SPEED OR WHEN CORNERING. THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION. Read More »
Some vehicles (without power seats) may exhibit a driver seat that gradually moves down by itself. This concern may be caused when a load, which is applied to the seat during braking, exceeds a certain level that could impact the ... Read More »
Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. Read More »
Some vehicles (without power seats) may exhibit a driver seat that gradually moves down by itself. This concern may be caused when a load, which is applied to the seat during braking, exceeds a certain level that could impact the ... Read More »
Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. Read More »
Some vehicles may exhibit excessive noise when operating either front power seat forward or backward. The noise may be caused by cable vibration, which transmits power from the motor to the gears. Read More »
FRONT POWER SEATS DO NOT SLIDE BACK AND FORTH. SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. Read More »
SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. Read More »
SOME VEHICLES (WITHOUT POWER SEATS) MAY EXHIBIT A DRIVER SEAT THAT GRADUALLY MOVES DOWN BY ITSELF. THIS CONCERN MAY BE CAUSED WHEN A LOAD, WHICH IS APPLIED TO THE SEAT DURING BRAKING, EXCEEDS A CERTAIN LEVEL THAT COULD IMPACT THE ... Read More »
SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. Read More »
SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with ... Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
When the engine is started for the first time after parking overnight in cold weather (below freezing), some vehicles may exhibit the check engine light on with DTC P0451 (fuel tank pressure sensor: sensor characteristic malfunction) ... Read More »
Unusual engine noise after a cold engine start. Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. Read More »
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
Some vehicles (without power seats) may exhibit a driver seat that gradually moves down by itself. This concern may be caused when a load, which is applied to the seat during braking, exceeds a certain level that could impact the ... Read More »
This service bulletin provides information regarding the proper use of the driver??A?A?s floor mat to avoid any potential interference with the foot pedals. Read More »
NAVIGATION UPDATES FOR TOMTOM NAVIGATION SYSTEM. Some customers may request updates for their vehicle's navigation system. Refer customers to Mazdausa.com. Read More »
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section ... Read More »
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all ... Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
Some customers may expierience one or more of the following: ??A?A? intermittent no start ??A?A? engine stall ??A?A? many DTC's stored ??A?A? no communication with the PCM. This may be caused by a poor C-11 or C-12 electrical connection. Read More »
Some customers may complain about no cool air from the vents when the air conditioner (A/C) is ON. This concern may be caused by A/C refrigerant leaking from the evaporator at the joint between the tubes and the header due to improper ... Read More »
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
Some customer using ??A???A???A?Flexible??A???A???A? setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. Read More »
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
NO GPS AFTER TOMTOM NAVIGATION ACCESSORY INSTALLATION: When not equipped with TomTom navigation from the factory, the GPS antenna plugs into the handsfree (Bluetooth) unit. Read More »
When troubleshooting a radar unit, DO NOT swap it with another vehicle. Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Read More »
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
Some vehicles may exhibit excessive noise when operating either front power seat forward or backward. The noise may be caused by cable vibration, which transmits power from the motor to the gears. Read More »
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
This service information provides basic Q-85/T-110 battery handling procedures. Complete service information can be found in MGSS online or Workshop Manual (section 13-17). Read More »
Some vehicles may exhibit the driver seat manual lumbar support adjustment (A) inoperative. This may be caused byrepeated stress to the lumbar support lever (C) at location (B). Read More »
RAISING A VEHICLE WITH A JACK CAN BE DANGEROUS IF NOT DONE PROPERLY. THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNER?S MANUAL. Read More »
WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE RESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. Read More »
SOME VEHICLES MAY EXHIBIT A TOUCH SCREEN THAT LOCKS UP (BLACK SCREEN) OR DOES NOT RESPOND. HOWEVER, IN EITHER CASE THE AUDIO SOUND IS NORMAL. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE AUDIO UNIT. Read More »
SOME VEHICLES MAY EXHIBIT BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM ... Read More »
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. Read More »
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. Read More »
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT A RATTLE TYPE NOISE COMING FROM THE REAR OF THE VEHICLE WHEN DRIVING ON ROUGH ROADS. THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK. Read More »
Some customers may complain about a rattle type noise coming from the rear of the vehicle when driving on rough roads. This may be caused by a loose spare tire jack. Read More »
THE REAR CONSOLE LID IS LOOSE. SOME CUSTOMERS MAY COMPLAIN ABOUT A LOOSE REAR CONSOLE LID (A). THIS MAY BE CAUSED BY HINGE PINS COMING PARTIALLY OFF (B) OR COMPLETELY OFF. Read More »
Creaking Noise From Front Lower Control Arm Bushings Some vehicles may exhibit a creaking noise from under the front of the vehicle when driving over bumps. The noise occurs at approx. Read More »
SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. Read More »
USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS. Read More »
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. Read More »
SOME CUSTOMERS MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING CLOCK SYMPTOM(S):?THE CLOCK RESETS TO 1:00 BY ITSELF.?THE CLOCK DISPLAY IS BLANK.?THE CLOCK DISPLAY FREEZES.?THE CLOCK DISPLAYS A WRONG TIME. Read More »
IN SUPPORT OF SKYACTIV MANUAL TRANSMISSION MODELS, MAZDA WILL SHIP TO ALL DEALERS ONE (1) NEW SPECIAL SER-VICE TOOL (SST). THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDA?S TOOL VENDOR SNAP-ON TOOLS, STARTING IN MID-OCTOBER 2014. Read More »
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS:?HARD TO SHIFT INTO 3RD GEAR?SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H)THIS IS CAUSED BY THE ... Read More »
MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. Read More »
SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE. Read More »
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
Some vehicles may exhibit BLUETOOTH? hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH? hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program ... Read More »
IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version. Read More »
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. Read More »
HANDS-FREE BLUETOOTH MODULE AND/OR TEXT MESSAGING TROUBLESHOOTING PROCEDURE. SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. Read More »
SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. Read More »
SOME VEHICLES MAY EXHIBIT EITHER AN AUDIO SCREEN THAT IS LOCKING-UP (BLACK SCREEN) OR AN INOPERATIVE AUDIO TOUCH SCREEN. IN BOTH CASES HOWEVER, THE AUDIO UNIT SOUND OUTPUT IS NORMAL. Read More »
SOME VEHICLES MAY EXHIBIT BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM ... Read More »
SOME CUSTOMERS MAY EXPERIENCE AN ELECTRICAL MALFUNCTION AFTER A VEHICLE BODY REPAIR. THE NEWLY PAINTED FENDER STAY (B) MAY BE CAUSING A POOR FRONT HARNESS (A) GROUND CONNECTION. Read More »
SOME CUSTOMERS MAY EXPERIENCE AN ELECTRICAL MALFUNCTION AFTER A VEHICLE BODY REPAIR. THE NEWLY PAINTED FENDER STAY (B) MAY BE CAUSING A POOR FRONT HARNESS (A) GROUND CONNECTION. Read More »
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
Some vehicles may experience unusual noise coming from inside the front door panel when playing the audio system. This is caused by the damper coming off the speaker frame due to corrosion. Read More »
Some vehicles may experience unusual noise coming from inside the front door panel when playing the audio system. This is caused by the damper coming off the speaker frame due to corrosion on the speaker back frame. Read More »
Some vehicles may exhibit navigation unit that cannot read out SMS (Short Messages Service) or does not operate properly after reading SMS. These concerns may be caused by problems with the Bluetooth Unit software. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. Read More »
WHEN REPLACING THE SIRIUSXM SATELLITE RADIO UNIT (OR A MAZDA CONNECT TUNER AND AMP UNIT (TAU)) WITH REPLACEMENT TUNER FOR ANY REASON, A CALL MUST BE MADE TO INFORM SIRIUSXM OF THE EXISTING RADIO ID AND THE NEW/ REPLACEMENT SAT RADIO ID AS ... Read More »
Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified. Read More »
Some vehicles may exhibit navigation unit that cannot read out SMS (Short Messages Service) or does not operate properly after reading SMS. These concerns may be caused by problems with the Bluetooth Unit software. Read More »
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. ? TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. Read More »
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. ? TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. Read More »
AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. Read More »
AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. Read More »
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
Some vehicles may exhibit oil residue on the engine front cover from seepage around the joint portion (A) between the cylinder block and head. It becomes very noticable with dust adhesion. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT STRUT BEARING (A) WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
The owner??A?A?s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Read More »
Subject: 2014-2016 Mazda6 - Door Sash Molding Concern Special Service Campaign (SSP) A5. The purpose of this email is to notify you that on January 25th, customers will be mailed a re-notification letter to improve SSPA5 completion rates. Read More »
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. Read More »
Some vehicles may experience an engine that runs rough and the check engine light on with DTCs P0201 and P0204 or P0202 and P0203. NOTE: Engine misfire related DTCs (P0301, P0302, P0303, P0304) are usually stored at the same time. Read More »
PERMANENT DTCS ARE NOW DISPLAYED WITH THE IDS 104 UPDATE. THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. Read More »
IN SUPPORT OF IMPROVED ELECTRICAL DIAGNOSIS ON SKYACTIV VEHICLES, MAZDA WILL SHIP A TERMINAL TEST KIT TO ALL DEALERS. THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. ? P0015:00 - EXHAUST CMP TIMING OVER-RETARDED ? P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE ... Read More »
SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 ?F (0 ?C). ? P0116:00: ECT SENSOR NO. Read More »
MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITHOUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). Read More »
SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 ?F (0 ?C). ? P0116:00: ECT SENSOR NO. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. ? P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY ... Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXHIBIT INSTRUMENT CLUSTER TPMS, ABS AND TCS/DSC INDICATOR WARNING LIGHTS ON AND DTC U3000:49[STANDARD DEPLOYMENT CONTROL SYSTEM] OR C0061:29, C0062:29, C0063:29 [STANDARD DEPLOYMENT CONTROL SYSTEM] STORED IN MEMORY. Read More »
AFTER PERFORMING RECALL CAMPAIGN 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
IN SUPPORT OF THE SKYACTIV MODELS, MAZDA WILL MAKE AVAILABLE A SPECIAL SERVICE TOOL (SST), TO ADDRESS FRONT SUSPENSION NOISE FOR SPECIFIC HIGH HUMIDITY AND WET CLIMATE CONDITIONS IN THE LOWER GULF STATES. Read More »
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).?NAVIGATION SYSTEM FREEZES. Read More »
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY.THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. Read More »
SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P2610 (INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM) STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. Read More »
SOME VEHICLES MAY EXHIBIT BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM ... Read More »
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY.THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. Read More »
SOME CUSTOMERS MAY EXPERIENCE THE FOLLOWING SYMPTOM:A.WARNING MESSAGE ?I-ELOOP MALFUNCTION? (MAZDA3) OR ?I-ELOOP INSPECTION REQUIRED? (MAZDA6) IS DIS-PLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING.B. Read More »
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS:1. SYMPTOM (MAZDA6 ONLY)A.WARNING MESSAGE ?I-ELOOP INSPECTION REQUIRED? IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING.B. Read More »
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER).? VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.?P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.?P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.?P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. ? P0842:00 - OIL PRESSURE SWITCH NO. Read More »
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS: 1. SYMPTOM (MAZDA6 ONLY) A. WARNING MESSAGE ?I-ELOOP INSPECTION REQUIRED? IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING. B. Read More »
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS: 1. SYMPTOM (MAZDA6 ONLY) A. WARNING MESSAGE ?I-ELOOP INSPECTION REQUIRED? IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING. B. Read More »
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS: 1. SYMPTOM (MAZDA6 ONLY) A. WARNING MESSAGE ?I-ELOOP INSPECTION REQUIRED? IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING. B. Read More »
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS: 1. SYMPTOM (MAZDA6 ONLY) A. WARNING MESSAGE ?I-ELOOP INSPECTION REQUIRED? IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING. B. Read More »
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
Some customers may complain that the headlights are not as bright as they had previously been. This is caused by a dulled headlight reflector in the front combination light. Read More »
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. Read More »
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. Read More »
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
CORROSION AROUND SPOT WELDS IN TRUNK OPENING. SOME VEHICLES MAY EXHIBIT CORROSION AROUND THE SPOT WELDS IN TRUNK OPENING UNDER THE REAR WINDOW. THIS IS CAUSED BY INSUFFICIENT PAINT THICKNESS AT THE SPOT WELDS. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT A LOOSE REAR CONSOLE LID (A). THIS MAY BE CAUSED BY HINGE PINS COMING PARTIALLY OFF (B) OR COMPLETELY OFF. Read More »
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT A LOOSE REAR CONSOLE LID (A). THIS MAY BE CAUSED BY HINGE PINS COMING PARTIALLY OFF (B) OR COMPLETELY OFF. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT A LOOSE REAR CONSOLE LID (A). THIS MAY BE CAUSED BY HINGE PINS COMING PARTIALLY OFF (B) OR COMPLETELY OFF. Read More »
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:?MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS. Read More »
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVER?S FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
Some customers may complain about no cool air from the vents when the air conditioner (A/C) is ON. This concern may be caused by A/C refrigerant leaking from the evaporator at the joint between the tubes and the header due to improper ... Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a clogged heater unit. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CONCERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. Read More »
SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CON-CERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. Read More »
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
