Technical Service Bulletins (TSBs) for the 2005 Sierra 2500 are official communications between GMC & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Read More »
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal. Read More »
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. Read More »
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. Read More »
This preliminary informational bulletin provides a diagnostic tip for coolant leak at oil cooler inlet pipe o-ring after service engine replacement. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Read More »
This informational bulletin provides Information on Identifying Duramax Diesel Overpower Engine Breakdown/Non-Function Due to Aftermarket Power-Up Devices vs Non Overpower Engine Non-Function of Pistons, Cylinders, Valvetrain Components, ... Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This SKU is a Diesel Fuel Filter Housing. The customer communication requested return of unsold inventory to inspect the fuel filter threads. The threads may be misformed such that the fuel filter cannot be installed. Read More »
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic ... Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic ... Read More »
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty. Read More »
This informational bulletin adds models to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging. Read More »
This informational bulletin adds 2011 - 2014 model years to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging. Read More »
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection ... Read More »
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the ... Read More »
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
GMC/CHEVROLET: SEE DOCUEMTN SEARCH BUTTON FOR OWNER LETTER. AUXILIARY BATTERY FEED MAY CAUSE FUSIBLE LINK TO MELT AND OPEN CIRCUIT TO PREVENT DAMAGE OR FIRE IN WIRING HARNESS, DUE TO ELECTRICAL OVER LOAD. Read More »
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). Read More »
ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the ... Read More »
This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
UNABLE TO DISABLE AUTO DOOR LOCKS. THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. Read More »
UNABLE TO DISABLE AUTO DOOR LOCKS. THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing Hardman Double Bubble Epoxy part number 04001. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information. Read More »
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS. Read More »
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels. Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing Hardman Double Bubble Epoxy part number 04001. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
