Technical Service Bulletins (TSBs) for the 2018 LaCrosse are official communications between Buick & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This engineering information (EI) closure ends the need for information from the field on a stick-slip type condition felt in steering wheel at highway speeds. Read More »
This engineering information bulletin is requesting to gather information from the field to determine a root cause for a condition of a stick-Slip Type Condition Felt in Steering Wheel at Highway Speeds. Read More »
This engineering informational bulletin is requesting to gather information from the field to determine a root cause for a condition of a stick-Slip Type Condition Felt in Steering Wheel at Highway Speeds. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport ... Read More »
17247 - Service Update. Certain vehicles may exhibit a rattle noise in the rear of the vehicle. This noise may be caused by a loose rear suspension bolt. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This technical bulletin provides a procedure to add a washer to prevent the rear shock outer housing making solid contact with the shock mount isolation rubber. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
17247 - Service Update. Certain vehicles may exhibit a rattle noise in the rear of the vehicle. This noise may be caused by a loose rear suspension bolt. Read More »
This technical bulletin provides a procedure to correct the condition of Front End Rattle Noise when Braking Moderate or Hard on Rough Surfaces. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This technical bulletin provides a procedure to replace both front lower control arms to correct the condition of Front End Rattle Noise when Braking Moderate or Hard on Rough Surfaces due to metal on metal contact within the control arms. Read More »
This technical bulletin provides a procedure to replace both front lower control arms to correct the condition of Front End Rattle Noise when Braking Moderate or Hard on Rough Surfaces due to metal on metal contact within the control arms. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This service bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Read More »
This technical bulletin provides a procedure to correct the condition of Front End Rattle Noise when Braking Moderate or Hard on Rough Surfaces. Read More »
This technical bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Technical bulletin provides information for rear brake pad replacement to correct a squeak type noise heard from the rear brakes when cold. Read More »
This Technical bulletin provides information for rear brake pad replacement to correct a squeak type noise heard from the rear brakes when cold. Read More »
This Technical bulletin provides information for rear brake pad replacement to correct a squeak type noise heard from the rear brakes when cold. Read More »
Rear Brake Squeak Type Noise Involved Region or Country North America and N.A. Export Regions Condition Some customers may comment on a squeak type noise heard from the rear brakes when cold. Read More »
This Technical bulletin provides information for rear brake pad replacement to correct a squeak type noise heard from the rear brakes when cold. Read More »
Rear Brake Squeak Type Noise Condition Some customers may comment on a squeak type noise heard from the rear brakes when cold. This noise will typically occur on first brake apply when the brakes are cold. Read More »
Rear Brake Squeak Type Noise Involved Region or Country North America and N.A. Export Regions Condition Some customers may comment on a squeak type noise heard from the rear brakes when cold. Read More »
This Technical bulletin provides information for rear brake pad replacement to correct a squeak type noise heard from the rear brakes when cold. Read More »
Rear Brake Squeak Type Noise Condition Some customers may comment on a squeak type noise heard from the rear brakes when cold. This noise will typically occur on first brake apply when the brakes are cold. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a crank but engine does not start concern. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides diagnostic strategy information to aid in diagnosing a Ticking, Tap or Rattle Noise from Engine with Possible Misfire, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from ... Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates a possible BCM and/or circuit 5985 concern if DTC P0747 sets during engine shut down when the transmission is in park or neutral when no hydraulic/mechanical transmission concerns are present. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
Special Coverage Adjustment - Certain 2016-2018 model year Chevrolet Malibu, 2017-2018 model year Buick LaCrosse, and 2018 model year Buick Regal vehicles may have a condition which affects the electrical connection to one of the ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This Preliminary information communicates a possible BCM concern if DTC P0747 sets during engine cranking when the transmission is in park. Read More »
This Preliminary information communicates a possible BCM concern if DTC P0747 sets during engine cranking when the transmission is in park. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
Certain 2016-2018 model year Chevrolet Malibu, 2017-2018 model year Buick LaCrosse, and 2018 model year Buick Regal vehicles may have a condition which affects the electrical connection to one of the vehicle?s accelerator pedal position ... Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary information communicates that a customer may bring a vehicle in with a complaint that the engine rpm increased and/or the vehicle downshifted for no reason. Read More »
This Preliminary information communicates there is an investigation into cause and correction for this group of DTC's setting together. (P0011, P0014, P0021, P0024). Read More »
This Preliminary information communicates to the technician where to find the engine identification tag and what information on that tag to use during programming of someengine control modules. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a crank but engine does not start concern. Read More »
Special Coverage. Certain vehicles may have a condition which affects the electrical connection to one of the vehicle?s accelerator pedal position sensors. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary information communicates there is an investigation into cause and correction for this group of DTC's setting together. (P0011, P0014, P0021, P0024). Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years. Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin advises the technician not to change the crankshaft balancer if it has the illusion of a wobble or vibration appearance. Read More »
This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminateda??. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from ... Read More »
This service bulletin advises the tech that the rotational Clicking Noise Heard After Engine Shut Down may be normal characteristics of the vehicle. Read More »
This Preliminary information communicates that a rotational clicking noise heard after engine shut down is a design characteristic and no repairs should be attempted. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This service bulletin advises the technician of a diagnostic test for a possible issue with a damaged OCV solenoid that may cause an oil leak and misfire, illuminating the MIL and setting DTCs P0300, P0302 and/or P0305. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
Service Update Bulletin (revised service procedure). In vehicles equipped with a 2.5L engine, the Engine Control Module (ECM) may not respond to test tools with the correct Calibration Verification Number (CVN). Read More »
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
N192266190 - Service Update. Certain vehicles may have an engine control software issue that can occur during a stop/start event that is causing drivability concerns such as the engine running roughly. Read More »
This engineering informational bulletin is requesting to gather information from the field to determine a root cause for a condition of oil leaking from the valve rocker arm oil control valve. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
The Preliminary Information communicates that a vehicle may come into the dealer with a SES light on and code P0446 set in Engine Control Module. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This Preliminary information communicates that a rotational clicking noise heard after engine shut down is a design characteristic and no repairs should be attempted. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary information communicates that a p0A90 could be caused by a missing Stop bolt and Brace. This is for the lower tensioner that can tavel to far with out the stop. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface ... Read More »
18046 - Service Update. On certain vehicles, the motor generator unit (MGU) coolant hose may contact the battery power inverter module (BPIM). Customers may experience a coolant leak. Dealers are to install a shorter bolt. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides a repair procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3055 Set. Read More »
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). Read More »
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
18046 - Service Update. On certain vehicles, the motor generator unit (MGU) coolant hose may contact the battery power inverter module (BPIM). Customers may experience a coolant leak. Dealers are to install a shorter bolt. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
18239 - Emissions Recall - General Motors has decided to conduct a Voluntary Emission Recall involving certain 2018 model year vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). Read More »
The Preliminary Information communicates that avehicle may come into the dealer with a SES light on and code P0446 set in Engine Control Module. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement due to active shutters being inoperative. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This bulletin provides procedure information for hard to fuel and/or fuel filling station nozzle shuts off repeatedly due to the vapor generation reduction device inside the fuel filler pipe. Read More »
FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin advises the tech that the rotational Clicking Noise Heard After Engine Shut Down may be normal characteristics of the vehicle. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This service bulletin provides repair information to correct a customer concern of a SES light or Service Transmission Soon message appearing in the DIC. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates that a technician may find U135A and/or P26C8 set after replacing the Transmission Range Control module. The tech is advised not to perform any further repairs to the vehicle. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the door locks will unlock immediately after auto locking usually at startup or while driving. Read More »
This service bulletin advises the tech that the rotational Clicking Noise Heard After Engine Shut Down may be normal characteristics of the vehicle. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This technical bulletin provides a service procedure to correct a customer concern of Momentary Sharp Deceleration During 1-2 Upshift or a Momentary Neutral During 2-4 Upshift, Transmission Stuck in 2nd Gear, MIL Illuminated. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary information communicates a possible BCM and/or circuit 5985 concern if DTC P0747 sets during engine shut down when the transmission is in park or neutral when no hydraulic/mechanical transmission concerns are present. Read More »
This Preliminary information communicates a possible BCM and/or circuit 5985 concern if DTC P0747 sets during engine shut down when the transmission is in park or neutral when no hydraulic/mechanical transmission concerns are present. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates a possible BCM and/or circuit 5985 concern if DTC P0747 sets during engine shut down when the transmission is in park or neutral when no hydraulic/mechanical transmission concerns are present.. Read More »
This Preliminary information communicates a possible BCM concern if DTC P0747 sets during engine cranking when the transmission is in park. Read More »
This Preliminary information communicates a possible BCM concern if DTC P0747 sets during engine cranking when the transmission is in park. Read More »
This Preliminary information communicates a possible BCM concern if DTC P0747 sets during engine cranking when the transmission is in park. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This informational bulletin advises the tech of a possible normal condition caused when the transmission performs a 1-2 upshift at light throttle and why the D in the PRNDL will flash. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
N182200470 - Customer Satisfaction - Certain 2018 model year Buick Enclave and LaCrosse vehicles, and 2018 - 2019 model year GMC Terrain vehicles, may have a condition that occurs when the driver places the vehicle in neutral immediately ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary information communicates that a customer may bring a vehicle in with a complaint that the engine rpm increased and/or the vehicle downshifted for no reason. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
Special Coverage. Certain vehicles may have a condition which affects the electrical connection to one of the vehicle?s accelerator pedal position sensors. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface ... Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has ended the part restriction for the T87A Transmission Control Module. Read More »
This Preliminary information communicates that the valve body assembly for any vehicle equipped with a 9T50/60 transmission assembly equipped with the ETRS will require engineering review for possible complete transmission assembly ... Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction that has ended for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
N192216310 - Service Update - Certain vehicles may have a condition wherethe customer may be able to shift out of park with and expired latent fault mode counter. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary information communicates that the valve body assembly for any vehicle equipped with a 9T50/60 transmission assembly equipped with the ETRS will require engineering review for possible complete transmission assembly ... Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This technical bulletin provides a procedure to reprogram the TCM to correct a condition of Vehicle Wont Shift Out of Park, Stuck in Gear or Tie Up Feeling on 1-2 Shift, Wont Shift Into Park or Reverse, PRNDL May Blink with Possible DTC ... Read More »
Information on Chassis Control Module (CCM) and Hybrid Powertrain Control Module (HPCM) Receives Invalid Data and Sets DTC U0422 The technician may find DTC U0422 set. Read More »
This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This service bulletin advises the tech that the rotational Clicking Noise Heard After Engine Shut Down may be normal characteristics of the vehicle. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides repair information to correct a customer concern of a SES light or Service Transmission Soon message appearing in the DIC. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the door locks will unlock immediately after auto locking usually at startup or while driving. Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This service bulletin advises the technician of a diagnostic test for a possible issue with a damaged OCV solenoid that may cause an oil leak and misfire, illuminating the MIL and setting DTCs P0300, P0302 and/or P0305. Read More »
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States. Read More »
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This service bulletin provides diagnostic strategy information to aid in diagnosing a Ticking, Tap or Rattle Noise from Engine with Possible Misfire, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated - DTC P3055 Set. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
Service Update Bulletin. In vehicles equipped with a 2.5L engine, the Engine Control Module (ECM) may not respond to test tools with the correct Calibration Verification Number (CVN). Read More »
Service Update Bulletin (revised service procedure). In vehicles equipped with a 2.5L engine, the Engine Control Module (ECM) may not respond to test tools with the correct Calibration Verification Number (CVN). Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw. Read More »
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic. Read More »
This Preliminary information communicates a possible BCM concern if DTC P0747 sets during engine cranking when the transmission is in park. Read More »
This Preliminary information communicates a work around when only 11 digit PUN (Part Unique Number) is seen on Service Solenoid Body Assembly. Read More »
This engineering Information (EI) ends the need for information from the field for a condition of oil leaking from the valve rocker arm oil control valve. If a vehicle is encountered with this condition, refer to SI for further diagnosis. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
N192266190 02 - Service Update - (Revised Service Procedure for XT5). Certain vehicles may have an engine control software issue that can occur during an automatic stop/start event. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
N192266190 01 - Service Update. Certain 2018 model year Buick LaCrosse, Enclave, Cadillac XT5 and Chevrolet Traverse vehicles may have an engine control software issue that can occur during an automatic stop/start event. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
N192266190 - Service Update. Certain vehicles may have an engine control software issue that can occur during a stop/start event that is causing drivability concerns such as the engine running roughly. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
Certain 2016-2018 model year Chevrolet Malibu, 2017-2018 model year Buick LaCrosse, and 2018 model year Buick Regal vehicles may have a condition which affects the electrical connection to one of the vehicle?s accelerator pedal position ... Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com. or http://www.nfpa. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement due to active shutters being inoperative. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This technical bulletin provides a procedure to replace the GEN I charging system with a GEN II charging system only if vehicles apply within the settings. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). Read More »
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Circular Distortion in the Circle Icons and the Buick Tri-Shield Start Up Screen on the radio display. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface ... Read More »
Special Coverage. Certain vehicles may have a condition which affects the electrical connection to one of the vehicle?s accelerator pedal position sensors. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface ... Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface ... Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for theGenerator Control Module (GCM). Read More »
This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern. Read More »
This technical bulletin provides a procedure to perform diagnostics on the codes set and if no problem is found, to replace either the input or output speed sensor. Read More »
This technical bulletin provides a procedure to reprogram the memory set module to correct a condition of Personalization Selections Intermittently Missing from Comfort and Convenience Menu due to a calibration concern. Read More »
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar? Module Functionality After OnStar Module Replacement for Another Condition. Read More »
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement due to active shutters being inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary information communicates that a customer may bring a vehicle in with a complaint of the Heads Up Display (HUD) frozen or inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Read More »
This Preliminary Information communicates to thetechnician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
Information on Chassis Control Module (CCM) Receives Invalid Data and Sets DTC U0422 The Technician may find DTCs U0422 set. The Technician may also find the following DTCs set. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin provides information for programming the low speed LAN module due to the mirrors memory position reverse tilt position is inoperative. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This informational bulletin provides to the technician, locations to check for possible loose or damaged electrical connections that may set a DTC instead of just replacing a part. Read More »
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off. Read More »
This Preliminary information communicates that a p0A90 could be caused by a missing Stop bolt and Brace. This is for the lower tensioner that can tavel to far with out the stop. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
18046 - Service Update. On certain vehicles, the motor generator unit (MGU) coolant hose may contact the battery power inverter module (BPIM). Customers may experience a coolant leak. Dealers are to install a shorter bolt. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface ... Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This informational bulletin explains how the technician no longer needs to perform the 3 hour battery relearn procedure on 2017-2018 vehicles with Start/Stop. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement to correct a MIL Illuminated with DTCs and active shutters being inoperative. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This technical bulletin provides a procedure to repair the crankshaft positioning sensor wiring harness by installing a new wiring harness. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides repair information to correct a customer concern of passive entry and passive starting functions are always inoperative on one, or both, of the RKE Fobs, possible various DIC messages. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
All or Some Options May Be Missing from Driver Information Center (DIC) ?Info Pages? Menu Due to Them Not Being Selected Condition Some customers may comment that with the ?Info? option selected from the main menu (1), the ?Info ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates there is an investigation into cause and correction for this group of DTC's setting together. (P0011, P0014, P0021, P0024). Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a Service Driver Assist System Message with B172E stored in history Do not replace any parts. Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle. Read More »
This Preliminary information communicates thata vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a Service Driver Assist System Message with B172E stored in history Do not replace any parts. Read More »
This Preliminary information communicates thata vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use. Read More »
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed. Read More »
This informational bulletin describes what technicians should do if they are unable to perform a TRCM Range Motor Position Learn after a TRCM replacement and to validate that the TRCM has latest software. Read More »
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Read More »
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This informational bulletin provides information for assisting the customer in setting the position for the memory mirror and the reverse tilt Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates a condition where there is only newer hardware available when replacing the Active Safety Control Module. Read More »
This Preliminary information communicates a condition where there is only newer hardware available when replacing the Active Safety Control Module. Read More »
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the door locks will unlock immediately after auto locking usually at startup or while driving. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This Preliminary information communicates a work around when only 11 digit PUN (Part Unique Number) is seen on Service Solenoid Body Assembly. Read More »
This Preliminary information communicates a work around when only 11 digit PUN (Part Unique Number) is seen on Service Solenoid Body Assembly. Read More »
This Preliminary information communicates a work around when only 11 digit PUN (Part Unique Number) is seen on Service Solenoid Body Assembly. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This technical bulletin provides a procedure to add a washer to prevent the rear shock outer housing making solid contact with the shock mount isolation rubber. Read More »
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Read More »
This technical bulletin provides a procedure to correct the condition of Front End Rattle Noise when Braking Moderate or Hard on Rough Surfaces. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
Condition Information on Outside Door Handle or Lock Cylinder Cover Loose, Falling Off Some customers may comment on any of the following: ? Outside door handle loose. ? Outside door handle pulls out of door. Read More »
This informational bulletin provides information for dealers/technicians on an outside door handle or lock cylinder cover being loose, or falling off. Read More »
Condition Information on Outside Door Handle or Lock Cylinder Cover Loose, Falling Off Some customers may comment on any of the following: ? Outside door handle loose. ? Outside door handle pulls out of door. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the door locks will unlock immediately after auto locking usually at startup or while driving. Read More »
Special Coverage Adjustment - Certain 2016-2018 model year Chevrolet Malibu, 2017-2018 model year Buick LaCrosse, and 2018 model year Buick Regal vehicles may have a condition which affects the electrical connection to one of the ... Read More »
Certain 2016-2018 model year Chevrolet Malibu, 2017-2018 model year Buick LaCrosse, and 2018 model year Buick Regal vehicles may have a condition which affects the electrical connection to one of the vehicle?s accelerator pedal position ... Read More »
This Preliminary Information communication provides information to the technician that some owners may notice at roughly 3/4 of the way through the accelerator pedal travel there is a click felt in the pedal also the pedal gets harder to ... Read More »
This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This engineering information (EI) closure ends the need for information from the field on a stick-slip type condition felt in steering wheel at highway speeds. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
17339 - Service Update. Certain vehicles equipped with a spare tire (RPO QCL), may have a spare wheel assembly installed that will not have the correct lug pattern and either cannot be mounted to the vehicle, or may be difficult to mount ... Read More »
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided. Read More »
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels. Read More »
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw. Read More »
This technical bulletin provides repair information to correct a customer concern of front seat slight rocking movement while shifting weight from seat, during hard stops, and/or when driving over rough road surface. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This technical bulletin provides repair information to correct a customer concern of front seat slight rocking movement while shifting weight from seat, during hard stops, and/or when driving over rough road surface. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out Condition Some customers may comment on one or more of the following conditions: ? Forward Collision Alert ... Read More »
This Technical bulletin Reprograms the Radar Sensor Module-Long Range to correct a Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out condition. Read More »
Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out Condition Some customers may comment on one or more of the following conditions: ? Forward Collision Alert ... Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This technical bulletin provides a procedure to replace the Front Seat Lane Departure Warning Actuator if the B172E is set in the seat control module. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Preliminary Information communicates to thetechnician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Technical bulletin Reprograms the Radar Sensor Module-Long Range to correct a Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out condition. Read More »
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option. Read More »
This Preliminary information communicates that a rotational clicking noise heard after engine shut down is a design characteristic and no repairs should be attempted. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Technical bulletin provides information for rear brake pad replacement to correct a squeak type noise heard from the rear brakes when cold. Read More »
This Preliminary information communicates a condition where there is only newer hardware available when replacing the Active Safety Control Module. Read More »
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option. Read More »
Rear View Camera Guidelines Not Present at Times Condition Some customers may report that the Rear View Camera (RVC) guidelines are temporarily not available at times but the RVC will remain on during the concern. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides repair information to correct a customer concern of a SES light or Service Transmission Soon message appearing in the DIC. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin advises the technician of a diagnostic test for a possible issue with a damaged OCV solenoid that may cause an oil leak and misfire, illuminating the MIL and setting DTCs P0300, P0302 and/or P0305. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates a condition where there is only newer hardware available when replacing the Active Safety Control Module. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This technical bulletin provides a service procedure to correct a customer concern of Momentary Sharp Deceleration During 1-2 Upshift or a Momentary Neutral During 2-4 Upshift, Transmission Stuck in 2nd Gear, MIL Illuminated. Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary information communicates a work around when only 11 digit PUN (Part Unique Number) is seen on Service Solenoid Body Assembly. Read More »
This Preliminary information communicates a possible BCM concern if DTC P0747 sets during engine cranking when the transmission is in park. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Preliminary information communicates a work around when only 11 digit PUN (Part Unique Number) is seen on Service Solenoid Body Assembly. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement to correct a MIL Illuminated with DTCs and active shutters being inoperative. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This engineering information (EI) closure ends the need for information from the field on a stick-slip type condition felt in steering wheel at highway speeds. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary information communicates to the technician information on what may be setting DTC P06DE. This is in addition to what is already in the service manual. Read More »
This Preliminary information communicates to the technician information on what may be setting DTC P06DE. This is in addition to what is already in the service manual. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This technical bulletin provides a procedure to replace the HUD if found the cause of the Head-Up Display Inoperative or MIL Illuminated concern. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Circular Distortion in the Circle Icons and the Buick Tri-Shield Start Up Screen on the radio display. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have the outside air temperature display reading incorrectly. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Circular Distortion in the Circle Icons and the Buick Tri-Shield Start Up Screen on the radio display. Read More »
This Preliminary information communicates there is an investigation into cause and correction for this group of DTC's setting together. (P0011, P0014, P0021, P0024). Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical ... Read More »
This Preliminary information communicates that a p0A90 could be caused by a missing Stop bolt and Brace. This is for the lower tensioner that can tavel to far with out the stop. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). Read More »
This Preliminary information communicates there is an investigation into cause and correction for this group of DTC's setting together. (P0011, P0014, P0021, P0024). Read More »
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
Information on Chassis Control Module (CCM) Receives Invalid Data and Sets DTC U0422 The Technician may find DTCs U0422 set. The Technician may also find the following DTCs set. Read More »
Condition Information on Outside Door Handle or Lock Cylinder Cover Loose, Falling Off Some customers may comment on any of the following: ? Outside door handle loose. ? Outside door handle pulls out of door. Read More »
Rear View Camera Guidelines Not Present at Times Condition Some customers may report that the Rear View Camera (RVC) guidelines are temporarily not available at times but the RVC will remain on during the concern. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
Special Coverage Adjustment - Certain 2016-2018 model year Chevrolet Malibu, 2017-2018 model year Buick LaCrosse, and 2018 model year Buick Regal vehicles may have a condition which affects the electrical connection to one of the ... Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Circular Distortion in the Circle Icons and the Buick Tri-Shield Start Up Screen on the radio display. Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a Service Driver Assist System Message with B172E stored in history Do not replace any parts. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Circular Distortion in the Circle Icons and the Buick Tri-Shield Start Up Screen on the radio display. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4). Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Read More »
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis. Read More »
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered. Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a Service Driver Assist System Message with B172E stored in history Do not replace any parts. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Read More »
The PI was created to advise of an engineering investigation for a concern of unable to connect toOnStar Virtual Advisor when selecting "New Destination" in the OnStar menu. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This technical bulletin provides a procedure to program the radio to correct a condition of Circular Image Distortion in circle icons and Buick Tri-Shield Start-up Screen. Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This technical bulletin provides a procedure to test the radios receiver if certain XM channels cut out (mutes) depending on location of the vehicle. Read More »
This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical ... Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates a possible BCM and/or circuit 5985 concern if DTC P0747 sets during engine shut down when the transmission is in park or neutral when no hydraulic/mechanical transmission concerns are present. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary information communicates to the technician where to find the engine identification tag and what information on that tag to use during programming of someengine control modules. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This technical bulletin provides a service procedure to correct a customer concern of Momentary Sharp Deceleration During 1-2 Upshift or a Momentary Neutral During 2-4 Upshift, Transmission Stuck in 2nd Gear, MIL Illuminated. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary information communicates a work around when only 11 digit PUN (Part Unique Number) is seen on Service Solenoid Body Assembly. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This engineering Information (EI) ends the need for information from the field for a condition of oil leaking from the valve rocker arm oil control valve. If a vehicle is encountered with this condition, refer to SI for further diagnosis. Read More »
This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement to correct a MIL Illuminated with DTCs and active shutters being inoperative. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This technical bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary information communicates that a p0A90 could be caused by a missing Stop bolt and Brace. This is for the lower tensioner that can tavel to far with out the stop. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). Read More »
This Preliminary information communicates there is an investigation into cause and correction for this group of DTC's setting together. (P0011, P0014, P0021, P0024). Read More »
Information on Chassis Control Module (CCM) Receives Invalid Data and Sets DTC U0422 The Technician may find DTCs U0422 set. The Technician may also find the following DTCs set. Read More »
Rear View Camera Guidelines Not Present at Times Condition Some customers may report that the Rear View Camera (RVC) guidelines are temporarily not available at times but the RVC will remain on during the concern. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This technical bulletin provides a procedure to clean out the HVAC drain hose if a vehicle has a condition of Front Carpet Wet and/or Musty Smell with Possible DTC P3055 or P3056 due to the water coming inside. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
