Technical Service Bulletins (TSBs) for the 2013 A3 are official communications between Audi & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Supersedes Technical Service Bulletin Group 48 number 13-37 dated February 28, 2013. Steering feels stiff after engine start on vehicles with generation 3 steering. DTCs may be stored in the power steering control module. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. Read More »
Supersedes Technical Service Bulletin Group 48 number 11-17 dated October 21, 2011. Steering feels stiff after engine start on vehicles with generation 3 steering. Incorrect software. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-34 dated November 13, 2012. Customers may report the following conditions on vehicles with less than 6000 miles. In some cases these conditions may be noticed at PDI. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 42 number 12-16 dated November 13, 2012. Loud cracking or rubbing noises are heard when the steering wheel is being turned. Steering is not affected and operates normally. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
AUDI: DUE TO A POSSIBLE MALFUNCTION OF GEARBOX, IN SOME VEHICLES, A MESSAGE MAY APPEAR IN CLUSTER AND BETWEEN AUTOMATIC TRANSMISSION FLUID (ATF) AND TRANSMISSION CONTROL MODULE, A REACTION MAY OCCUR. MODEL 2012-2013 A4, A5 CABRIOLET, A6. Read More »
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
Supersedes Technical Service Bulletin Group 48 number 13-37 dated February 28, 2013. Steering feels stiff after engine start on vehicles with generation 3 steering. DTCs may be stored in the power steering control module. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Because of exhaust gas pulsations, the wastegate flap and rods vibrate at the start of the boost air control. This vibration causes rattling or jarring noises. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-34 dated November 13, 2012. Customers may report the following conditions on vehicles with less than 6000 miles. In some cases these conditions may be noticed at PDI. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Customer may report creaking and squeaking noises from front axle when driving at low temperatures on rough/bumpy/uneven roads. The customer complaint can be reproduced. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
RUNNING GEAR: AUDI MAGNETIC RIDE - KNOCKING NOISES FROM REAR SHOCKS ON S3 (8V) AND TTS (FV) BRAKE SYSTEM: BRAKING NOISES - BASIC PRINCIPALS FOR DIAGNOSIS AND REPAIR. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
Due to a parts catalog error, an incorrect emissions related component may have been installed on some vehicles during a past service repair visit. Read More »
Due to a parts catalog error, an incorrect emissions related component may have been installed on some vehicles during a past service repair visit. Read More »
Inlet Air Box Housing Snow Flap Replacement & Oxygen Sensor Inspection/Replacement - The snow flap in the inlet air box housing may remain partially to fully open. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-29 dated September 16, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
AUDI: THE ENGINE WOULD HAVE A ROUGH IDLE, DIFFERENT MISFIRE FAULTS OR REDUCED PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, THAT CAUSES THE MALFUNCTION INDICATOR LAMP (MIL) ON. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. Read More »
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-73 dated March 7, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. Read More »
AUDI: SOME VEHICLES MAY EXPERIENCE ROUGH RUNNING. EXCESS MOISTURE MAYBE FOUND IN THE INTAKE PIPE. IT IS ALSO PROBABLE THAT THE ENGINE MAY NOT START. *JS Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Read More »
Supersedes Technical Service Bulletin Group 17 number 12 - 31 dated August 30, 2012. Oil consumption measurement - Repair Authorization (CA). Read More »
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference. Read More »
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement Read More »
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
This document contains the Service Action Code: 19L2. The document contains Additional inspection steps added to the work procedure. The coolant pump may develop a small leak over time. Read More »
This document contians the dealer letter that provides information on the 19L2 service action that wil be turned back on for Elsa visibility on or about August 06, 2015. Customer notification will begin on or about August 31, 2015. Read More »
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM. Read More »
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Moisture from the intake air condenses and collects in the charge air cooler. At cold temperatures, this moisture can freeze, causing blockage of the intake air system. Read More »
Moisture from the intake air condenses and collects in the charge air cooler. At cold temperatures, this moisture can freeze, causing blockage of the intake air system. Read More »
Moisture from the intake air condenses and collects in the charge air cooler. At cold temperatures, this moisture can freeze, causing blockage of the intake air system. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. Read More »
AUDI: SOME VEHICLES WILL EXPERIENCE ROUGH RUNNING OR A NO START CONDITION WITH MALFUNCTION INDICATOR LAMP (MIL) ON AND MAY NEED CHECKING HIGH PRESSURE FUEL PUMP FOR METALLIC PARTICLES. MODEL 2013-2016 A3, A8, Q5, 17. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:OIL COOLER
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
This bulletin provides instructions for when the MIL is on, and the vehicle either runs roughly or does not start in the presence of one or more of the following DTCs: P008700, P008800, P019100 Read More »
AUDI: TSB CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. ON SOME VEHICLES, OVERTIME A SMALL LEAK WILL DEVELOP IN THE COOLANT PUMP AND PUMP WILL NEED TO BE INSPECTED AND IF NECESSARY, REPLACED. Read More »
Inlet Air Box Housing Snow Flap Replacement & Oxygen Sensor Inspection/Replacement - The snow flap in the inlet air box housing may remain partially to fully open. Read More »
This document modifies the Audi warranty policies and procedures manual on the engine exhaust flap limited warranty extension. Supersedes AWA 13-03. Read More »
Supersedes Technical Service Bulletin Group 21 number 12-09 dated May 16, 2012. Rattling and/or jarring noises heard from the engine compartment/exhaust system between 1800 and 2900 rpm. Read More »
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement Read More »
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles. Read More »
2.0L TDI Engine (GEN 1) Emissions Modification ? Customer Only (Retail Sold) USA ONLY - The Environmental Protection Agency and California Air Resources Board have determined that Audi A3 vehicles equipped with a 2. Read More »
2.0L TDI Engine (GEN 1) Emissions Modification ? Customer Only (Retail Sold) USA ONLY - The Environmental Protection Agency and California Air Resources Board have determined that Audi A3 vehicles equipped with a 2. Read More »
Inlet Air Box Housing Snow Flap Replacement & Oxygen Sensor Inspection/Replacement - The snow flap in the inlet air box housing may remain partially to fully open. Read More »
The vehicle's engine management software has been improved to assure the vehicle's tailpipe emissions are optimized and operating efficiently. Read More »
This special notice is to inform dealers to return all part numbers listed in the document. Only superseded part numbers to be ordered going forward. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake ... Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-26 dated May 15, 2013. Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-69 dated March 6, 2014. The MIL is on. No start or rough running. DTCs are stored in the ECM. Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
Because of exhaust gas pulsations, the wastegate flap and rods vibrate at the start of the boost air control. This vibration causes rattling or jarring noises. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module. Read More »
Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC? s are present in the engine control module: Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP
Supersedes Technical Service Bulletin Group 20 number 13-26 dated May 15, 2013. Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Read More »
The MIL is on due to a Fuel Rail/System Pressure Too Low DTC stored in the ECM. Drivability concerns such as hard starting/no starting are present. Fuel pump may be making a straining noise. Outside temperature is sub-freezing. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-69 dated March 6, 2014. The MIL is on. No start or rough running. DTCs are stored in the ECM. Read More »
The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be ... Read More »
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
This document contains the customer letter in regards to 2009-2015 model year Audi TDI? clean diesel vehicles registered in Minnesota engine codes CBEA, CATA, CNRB, CPNA, CPNB using biodiesel blend fuels. Read More »
This document contains the dealer letter in regards to 2009-2015 model year Audi TDI? clean diesel vehicles registered in Minnesota engine codes CBEA, CATA, CNRB, CPNA, CPNB using biodiesel blend fuels. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-75 dated March 20, 2014. The MIL is on. No start or rough running. One or more DTCs are stored in the engine control module. Read More »
Beginning with MY2009, the filler necks of various TDI clean diesel vehicles were equipped with a misfueling guard (Figure 1). The guard minimizes the likelihood that fuel other than ultra-low sulfur diesel will be put into the vehicle. Read More »
This document modifies the Audi Warranty Policies and Procedures Manual applicable to engine codes CBEA, CATA, CNRB, CPNA, CPNB: 2009-2015 model year TDI? clean diesel vehicles using biodiesel blended fuels - registered in the state of ... Read More »
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel ... Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
Beginning with MY2013, the filler necks of all A3 TDI vehicles are equipped with a misfueling guard (Figure 1). The guard minimizes the likelihood that fuel other than ultra-low sulfur diesel will be put into the vehicle. Read More »
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, ... Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks ... Read More »
AUDI: DUE TO A POSSIBLE MALFUNCTION OF GEARBOX, IN SOME VEHICLES, A MESSAGE MAY APPEAR IN CLUSTER AND BETWEEN AUTOMATIC TRANSMISSION FLUID (ATF) AND TRANSMISSION CONTROL MODULE, A REACTION MAY OCCUR. MODEL 2012-2013 A4, A5 CABRIOLET, A6. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. Read More »
This informational bulletin contains information regarding creaking and squeaking noises from the front axle when driving at low temperatures on rough roads. Read More »
This informational bulletin contains information regarding creaking and squeaking noises from the front axle when driving at low temperatures on rough roads. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 ... Read More »
This bulletin contains repair instructions for when there is a remove key warning in DIS, MMI does not turn off with key removed, or locking with remote does not work. Read More »
RUNNING GEAR: AUDI MAGNETIC RIDE - KNOCKING NOISES FROM REAR SHOCKS ON S3 (8V) AND TTS (FV) BRAKE SYSTEM: BRAKING NOISES - BASIC PRINCIPALS FOR DIAGNOSIS AND REPAIR. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
The infotainment system (radio, navigation, etc.) is not switched off when the ignition key is removed. The steering column cannot be locked. The vehicle cannot be locked with the remote. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
DTC 00003 (Control Module - no or incorrect basic setting/adaptation) is stored in the instrument cluster control module, J285 (address word 17). It may be present following a reset of the Service Reminder Interval. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-29 dated December 20, 2011. The Bluetooth telephone bonding tone is too loud or quiet for the customer. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-79 dated March 20, 2013. MIL on. DTCs are stored in the engine control module (address word 01). Excess rattling (?diesel clatter?) coming from engine. Read More »
Contaminated or incorrect fuel can cause performance, drivability, and/or fuel delivery problems. Additional component replacement may be necessary to ensure that no contamination or debris remains after repair. Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module. Read More »
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing ... Read More »
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. Read More »
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. Read More »
The MIL is on due to a Fuel Rail/System Pressure Too Low DTC stored in the ECM. Drivability concerns such as hard starting/no starting are present. Fuel pump may be making a straining noise. Outside temperature is sub-freezing. Read More »
Engine will not start after standing in cold weather below 0?C (32?F). MIL may be illuminated with various induction and/or boost system faults stored in ECM. Moisture from the intake air condenses and collects in the charge air cooler. Read More »
The infotainment system (radio, navigation, etc.) is not switched off when the ignition key is removed. The steering column cannot be locked. The vehicle cannot be locked with the remote. Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored. Read More »
Effective immediately, the codes for the STP4 (2.0L TDI) and STP5 (3.0L TDI) actions will show the campaign code 23Q4 (2.0L TDI) and 23R8 (3.0L TDI) only on the Inventory Vehicle Open Campaign/Action Report. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. Read More »
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed ... Read More »
DTC 00003 (Control Module - no or incorrect basic setting/adaptation) is stored in the instrument cluster control module, J285 (address word 17). It may be present following a reset of the Service Reminder Interval. Read More »
The instrument cluster is pre-programmed to allow a maximum service interval of 15,000 kilometers, and checks to see that this value is not exceeded. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
Audi connect Gen1 and Gen2 systems: Differences and troubleshooting. The customer has a general concern related to Audi connect. Different features are included with different generations of the Audi connect system. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
The vehicle's engine management software has been improved to assure the vehicle's tailpipe emissions are optimized and operating efficiently. Read More »
VOLKSWAGEN: 2011-2013 INFORMATION ON REPLACEMENT OF THE TIPM SOFTWARE. THIS SOFTWARE CONTROLS THE TIPM OPERATION & FRONT EXTERIOR LIGHTING OF THE VEHICLE. *LJ Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or ... Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
DTC 02261 (Data medium - Faulty) is sporadically set in the navigation control module, J401 (address word 37). The vehicle has the MY2014 navigation database installed. The DVD label should read "Version 2013/2014". Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 48 number 11-17 dated October 21, 2011. Steering feels stiff after engine start on vehicles with generation 3 steering. Incorrect software. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light ... Read More »
Supersedes Technical Service Bulletin Group 94 number 12-96 dated November 1, 2012. Part or all of the daytime running lights do not work on vehicles equipped with LED daytime running lights. Read More »
Supersedes Technical Service Bulletin Group 94 number 11-52 dated October 11, 2011. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third ... Read More »
Supersedes Technical Service Bulletin Group 94 number 12 ? 88 dated September 25, 2012. The turn signal indicator lens is inoperative without any damage from outside influence. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake ... Read More »
Headlight range control warning displayed in instrument cluster. DTCs may or may not be present. Vehicle is equipped with cornering light and headlight range control module. Only vehicles equipped with Xenon headlight are affected. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
THE BULLETIN STATES A NORMAL FUNCTION OF THE HEADLIGHT SWITCH AND HOW TO FIX BUT NOT REPLACE. DEALER IS TO ADVISE CUSTOMER ON WHY THE HEADLIGHT SWITCH PRESSES IN. Read More »
Supersedes Technical Service Bulletin Group 94 number 13-12 dated March 29, 2013. The headlight switch knob was designed with a normal position and a pushed-in position. This feature was designed to avoid injuries during a collision. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
AUDI: CRACKS FORMING IN LENS DUE TO AMOUNT OF TENSION AND IMPROPER INSTALLATION WHICH CAUSES CONDENSATION TO BE SEEN. ALSO, TURN SIGNAL INDICATOR IS INOPERATIVE. MODEL 2008-2013 A3, A4, A5, CABRIOLET. Read More »
AUDI: BRAKE LIGHT LENS, DAYTIME RUNNING LIGHTS, FOG LIGHTS, SIDE MARKER LIGHTS, HEADLIGHTS, TAILLIGHTS, FRONT TURN SIGNALS WOULD ALL HAVE VISIBLE CONDENSATION INSIDE DUE DAMPNESS, FROM COLD LENS, SETTLING INSIDE. Read More »
This document contians the dealer letter that provides information on the 19L2 service action that wil be turned back on for Elsa visibility on or about August 06, 2015. Customer notification will begin on or about August 31, 2015. Read More »
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
AUDI: CRACKS HAS FORMED IN LENS, CAUSING CONDENSATION BEHIND THE LENS, MAKING INOPERATIVE THE SIGNAL INDICATOR, WITHOUT DAMAGE FROM OUTSIDE INFLUENCE. MODELS 2009-2013 A3, A4; 2008-2013 A5; 2010-2013 CABRIOLET. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
In conjunction with the New Mexico DMV, Audi will be sending Takata airbag recall reminder notices to approximately 389 Audi owners in the State of New Mexico on March 13, 2023. Read More »
In conjunction with the Massachusetts DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,907 Audi owners in the State of Massachusetts on March 13, 2023. Read More »
In conjunction with the Colorado DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,174 Audi owners in the State of Colorado on February 13, 2023. Read More »
In conjunction with the New York DMV, Audi will be sending Takata airbag recall reminder notices to approximately 5,165 Audi owners in the State of New York on October 17, 2022. Read More »
In conjunction with the Georgia Department of Revenue - Motor Vehicle Division and Department of Driver Services, Audi sent Takata airbag recall reminder notices to approximately 565 Audi owners in the State of Puerto Rico on July 25, 2022. Read More »
In conjunction with the Georgia Department of Revenue - Motor Vehicle Division and Department of Driver Services, Audi sent Takata airbag recall reminder notices to approximately 2,616 Audi owners in the State of Georgia on June 22, 2022. Read More »
In conjunction with the California Department of Motor Vehicles (DMV), Audi sent Takata airbag recall reminder notices to approximately 12,349 Audi owners in the State of California on April 29, 2022. Read More »
In conjunction with the Alabama Law Enforcement Agency (ALEA), Audi is sending Takata airbag recall reminder notices to approximately 939 Audi owners in the State of Alabama on March 23, 2022. Read More »
In conjunction with the South Carolina Department of Public Safety, Audi is sending Takata airbag recall reminder notices to approximately 1,290 Audi owners in the state of South Carolina on January 24, 2022. Read More »
In conjunction with the Idaho DMV, Audi will be sending Takata airbag recall reminder notices to approximately 688 Audi owners in the State of Idaho on August 30, 2021. Read More »
In conjunction with the New York DMV, Audi will be sending Takata airbag recall reminder notices to approximately 6,957 Audi owners in the State of New York on June 21, 2021. Read More »
In conjunction with the Texas DMV, Audi will be sending Takata airbag recall reminder notices to approximately 7,185 Audi owners in the State of Texas on May 17, 2021. Read More »
In conjunction with the Michigan Department of State, Audi will be sending Takata airbag recall reminder notices to approximately 3,000 Audi owners in the State of Michigan on August 10, 2020. Read More »
In conjunction with the County of Fort Bend, Audi will be sending Takata airbag recalll reminder notices to approximately 370 Audi owners in the State of Texas on July 28, 2020. Read More »
In conjunction with the Tennessee DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,300 Audi owners in the State of Tennessee on July 7, 2020. Read More »
In conjunction with the City of Miramar, Audi sent Takata airbag recall reminder notices to approximately 89 Audi owners in the State of Florida on June 26, 2020. Read More »
In conjunction with the City of La Puente, Audi will be sending Takata airbag recall reminder notices to approximately 45 Audi owners in the State of California on June 22, 2020. Read More »
In conjunction with the Nebraska DMV, Audi will be sending Takata airbag recall reminder notices to approximately 400 Audi owners in the State of Nebraska on March 23, 2020. Read More »
In conjunction with the Ohio DMV, Audi will be sending Takata airbag recall reminder notices to approximately 4,900 Audi owners in the State of Ohio on February 10, 2020. Read More »
In conjunction with the Georgia DMV, Audi will be sending Takata airbag recall reminder notices to approximately 5,200 Audi owners in the State of Georgia on January 24, 2020. Read More »
In conjunction with the South Carolina Department of Public Safety, Audi sent Takata airbag recall reminder notices to approximately 1,800 Audi owners in the state of South Carolina on January 20, 2020. Read More »
In conjunction with the California Bureau of Automotive Repair, Audi sent Takata airbag recall reminder notices to approximately 27,300 Audi owners in the state of California on January 14, 2020. Read More »
In conjunction with the Pennsylvania DMV, Audi sent Takata airbag recall reminder notices to approximately 9,100 Audi owners in the State of Pennsylvania on November 18, 2019. Read More »
In conjunction with the Arkansas DMV, Audi will be sending Takata airbag recall reminder notices to approximately 600 Audi owners in the state of Arkansas on November 19 2019. Read More »
In conjunction with the Houston Dept. of Neighborhoods, Audi will be sending Takata airbag recall reminder notices to approximately 2,300 Audi owners in the state of Texas on November 4, 2019. Read More »
In conjunction with the Florida Dept. of Highway Safety and Motor Vehicles, Audi will be sending Takata airbag recall reminder notices to approximately 10,000 Audi owners in the state of Florida on October 14, 2019. Read More »
In conjunction with the Minnesota DMV, Audi will be sending Takata airbag recall reminder notices to approximately 3,500 Audi owners in the State of Minnesota on September 16, 2019. Read More »
In conjunction with the North Carolina DMV, Audi will be sending Takata airbag recall reminder notices to approximately 4,500 Audi owners in the State of North Carolina on August 19, 2019. Read More »
In conjunction with the Virginia DMV, Audi will be sending Takata airbag recall reminder notices to approximately 4,294 Audi owners in the State of Virginia on August 12, 2019. Read More »
In conjunction with the City of Compton, Audi will be sending Takata airbag recall reminder notices to approximately 78 Audi owners in the State of California on August 5, 2019. Read More »
In conjunction with the Commonwealth of Kentucky Transportation Cabinet, Aud will be sending Takata airbag recall reminder notices to approximately 1,476 Audi owner in the state of Kentucky on July 15, 2019. Read More »
Mailing Information: In conjunction with the Wisconsin Department of Transportation Division of Motor Vehicles (DMV), Audi will be sending Takata airbag recall reminder notices to approximately 2,877 Audi owners in the state of Wisconsin ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
Mailing Information: In conjunction with the New York Department of Motor Vehicles, Audi will be sending Takata airbag recall reminder notices to approximately 15,000 Audi owners in the State of New York on May 23, 2019. Read More »
69N1, 69N2 - Campaign Parts Bulletin - Today, May 5th is the final standard weekly allocation of Takata airbag inflators. After this date, Takata allocations will be based on the previous week?s paid claim volume. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
Customer may report creaking and squeaking noises from front axle when driving at low temperatures on rough/bumpy/uneven roads. The customer complaint can be reproduced. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-49 dated August 8, 2011. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". Read More »
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph. Read More »
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and ... Read More »
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
Supersedes Technical Service Bulletin Group 74 number 14-19 dated May 9, 2014. The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. Read More »
Supersedes Technical Service Bulletin Group 74 number 14-18 dated February 26, 2014. The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. Read More »
The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. The damage is caused when the headrest of the rear seat backrest comes in contact with the back of the front seat. Read More »
Customer states the radio has a faint background static. No audio source is present. An audio source with low volume is being played. The vehicle is utilizing hill-hold. Vehicles with hill-hold (PR No. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin provides instructions for repairing a deivation in to coaxial cable between the rearview camera system module and the infotainment control module. Read More »
Supersedes Technical Service Bulletin Group 91 number 10 - 60 dated September 28, 2010. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
This bulletin provides instructions for repairing a deivation in to coaxial cable between the rearview camera system module and the infotainment control module. Read More »
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the ... Read More »
In conjunction with the Georgia Department of Revenue - Motor Vehicle Division and Department of Driver Services, Audi sent Takata airbag recall reminder notices to approximately 565 Audi owners in the State of Puerto Rico on July 25, 2022. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
In conjunction with the City of La Puente, Audi will be sending Takata airbag recall reminder notices to approximately 45 Audi owners in the State of California on June 22, 2020. Read More »
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI ... Read More »
Due to a parts catalog error, an incorrect emissions related component may have been installed on some vehicles during a past service repair visit. Read More »
Due to a parts catalog error, an incorrect emissions related component may have been installed on some vehicles during a past service repair visit. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage. Read More »
This communication is issued to remind dealers of the repair validation process for repair group 19. 2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 ... Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles. Read More »
2.0L TDI Engine (GEN 1) Emissions Modification ? Customer Only (Retail Sold) USA ONLY - The Environmental Protection Agency and California Air Resources Board have determined that Audi A3 vehicles equipped with a 2. Read More »
2.0L TDI Engine (GEN 1) Emissions Modification ? Customer Only (Retail Sold) USA ONLY - The Environmental Protection Agency and California Air Resources Board have determined that Audi A3 vehicles equipped with a 2. Read More »
Inlet Air Box Housing Snow Flap Replacement & Oxygen Sensor Inspection/Replacement - The snow flap in the inlet air box housing may remain partially to fully open. Read More »
This bulletin contains repair instructions for when there is a remove key warning in DIS, MMI does not turn off with key removed, or locking with remote does not work. Read More »
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward. Read More »
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has ... Read More »
This document modifies the Audi warranty policies and procedures manual on the engine exhaust flap limited warranty extension. Supersedes AWA 13-03. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin. Read More »
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed. Read More »
Customer states the radio has a faint background static. No audio source is present. An audio source with low volume is being played. The vehicle is utilizing hill-hold. Vehicles with hill-hold (PR No. Read More »
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. Read More »
VWGoA is pleased to inform you of the release and automatic delivery of new Required Special Tools used on Audi vehicles. Starting March 25, 2013, every Audi dealer will be shipped one AT-348 Special Tool Package, Freight F.O.B. Read More »
Customer may report creaking and squeaking noises from front axle when driving at low temperatures on rough/bumpy/uneven roads. The customer complaint can be reproduced. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
Supersedes Technical Service Bulletin Group 44 number 12-33 dated August 10, 2012. Customers may report conditions on vehicles with less than 2 weeks in service or less than 500 miles. Vehicle pulls ? left or right. Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 28 number 11-18 dated November 9, 2011. Radio turns on and off while vehicle is being driven. Clock in radio sporadically does not work. Door locks actuate while vehicle is being driven. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 91 number 14-19 dated January 3, 2014. Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
Customer states the radio has a faint background static. No audio source is present. An audio source with low volume is being played. The vehicle is utilizing hill-hold. Vehicles with hill-hold (PR No. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Read More »
The topics for the Audi IQS Newsletters are chosen based on "Voice of the Customer" data and respond directly to top concerns of Audi owners. They are designed to help educate you and make an impact on customer satisfaction. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 28 number 11-18 dated November 9, 2011. Radio turns on and off while vehicle is being driven. Clock in radio sporadically does not work. Door locks actuate while vehicle is being driven. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Customer states the radio has a faint background static. No audio source is present. An audio source with low volume is being played. The vehicle is utilizing hill-hold. Vehicles with hill-hold (PR No. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC. Read More »
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
DTC 02261 (Data medium - Faulty) is sporadically set in the navigation control module, J401 (address word 37). The vehicle has the MY2014 navigation database installed. The DVD label should read "Version 2013/2014". Read More »
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s). Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
2.0L TDI Engine (GEN 1) Emissions Modification ? Customer Only (Retail Sold) USA ONLY - The Environmental Protection Agency and California Air Resources Board have determined that Audi A3 vehicles equipped with a 2. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. Read More »
In conjunction with the Virginia DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,026 Audi owners in the State of Virginia on July 21, 2022. Read More »
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles. Read More »
2.0L TDI Engine (GEN 1) Emissions Modification ? Customer Only (Retail Sold) USA ONLY - The Environmental Protection Agency and California Air Resources Board have determined that Audi A3 vehicles equipped with a 2. Read More »
This communication instructs dealers to contact the Technical Assistance Center if they encounter any issues while performing the update for Campaign 23U7. Read More »
This bulletin explains how to do warranty coding for the "delight elements" of the extended emissions warranty for model year 2010 - 2013 2.0L TDI vehicles. Read More »
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Read More »
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. Read More »
This document contains the post from Scott Keogh to the customer in regards to Audi being in connection with the action involving certain TDI diesel products that do not comply with emisions standards. Read More »
This circular contains important information regarding A3 e-tron tooling. Information will be covered in the subsequent sections depending on the dealership's current status. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. Read More »
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center Read More »
The topics for the Audi IQS Newsletters are chosen based on "Voice of the Customer" data and respond directly to top concerns of Audi owners. They are designed to help educate you and make an impact on customer satisfaction. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. Read More »
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release ... Read More »
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, ... Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Read More »
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. Read More »
This communication is to inform you of upcoming Update 87D9. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing ... Read More »
In conjunction with the South Carolina Department of Public Safety, Audi is sending Takata airbag recall reminder notices to approximately 1,121 Audi owners in the state of South Carolina on September 19, 2022. Read More »
