Technical Service Bulletins (TSBs) for the 2016 BRZ are official communications between Subaru & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This bulletin announces a change made to the front lower control arm ball joint boots. The boot material has been changed to provide increased resistance to damage from ozone. Read More »
This bulletin announces a design change to the front strut mounts intended to address customer concerns of a popping-type sound which may be heard when making low speed turns. Read More »
This service Information bulletin provides precautions to follow when servicing the Brembo brake calipers utilized on the models listed. Because of their aluminum construction, it is critcal to take extra care when servicing. Read More »
This bulletin announces availability of a new stop lamp switch for the models listed above equipped with LED - type rear combination lamps. Read More »
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. Read More »
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. Read More »
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. Read More »
The purpose of this bulletin is to clarify the proper installation direction of the valve springs used on the FA engine. The springs have a light blue paint mark identifier as shown in the chart below. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
THIS BULLETIN ANNOUNCES AVAILABILITY OF REPROGRAMMING FILES FOR OPTIMIZING THE TRANSMISSION CONTROL MODULE (TCM) ON ALL 2015 AND SOME EARLY-PRODUCTION 2016MY VEHICLES TO CONTROL AN ENGINE IDLE SPEED FLUCTUATION CONDITION WHEN IN PARK OR ... Read More »
"THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH ... Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed in this bulletin. Read More »
The purpose of this bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed below: There are six areas that should be closely inspected if an oil leak is reported by the ... Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
This Service Information bulletin announces a change to the flywheel (pilot) bearing to a ?environmentally friendly? type which is compliant with the REACH (Registration, Evaluation, Authorization and restriction of CHemicals) ... Read More »
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. Read More »
This Service Information bulletin announces a design change to the internal contact portion of the oil pressure switch to increase durability Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched "chirp", "squeak" or "cricket" sound heard coming from the engine's Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
Effective with all 2015 model year cars and forward, the oil change interval is changing to 6,000 miles or 6 months, whichever comes first. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:SUMP/TANK:DRAIN PLUG
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This bulletin provides an additional service procedure for replacing the pulsation dampers located on both low-pressure fuel delivery pipes as shown in the illustration below. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. Read More »
This Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINKA? Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer. Read More »
This bulletin has been developed to outline the steps for gathering basic essential information during diagnosis and repair of the Infotainment concerns. (Applicable to all models with Harman or Denso CP1 Infotainment). Read More »
This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation a??Gen 2a?? and a??Gen 2.1a?? F10 Navigation and Display Audio systems. Read More »
This document discusses some of the conditions that may trigger an Automatic Collision Notification (CAN) (Gen1) or Advanced Automatic Collision Notification (AACN) (Gen2), without a collision, airbag deployment, or accident taking place. Read More »
This Service Information Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2 Telematics system equipped Subaru. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2" display. Read More »
This bulletin announces availability of a new stop lamp switch for the models listed above equipped with LED - type rear combination lamps. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2. Read More »
This bulletin announces availability of individual service parts and provides an installation procedure for the A/C compressor clutch assembly. Read More »
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. Read More »
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2? display. Read More »
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2? display. Read More »
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2? display. Read More »
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6. Read More »
Although Fujitsu TEN (F10) Navigation units utilize an externally (faceplate) accessible MicroSD memory card, the MicroSD card used in Clarion display audio units is internal and not accessible. Read More »
THIS BULLETIN ANNOUNCES AVAILABILITY OF REPROGRAMMING FILES FOR OPTIMIZING THE TRANSMISSION CONTROL MODULE (TCM) ON ALL 2015 AND SOME EARLY-PRODUCTION 2016MY VEHICLES TO CONTROL AN ENGINE IDLE SPEED FLUCTUATION CONDITION WHEN IN PARK OR ... Read More »
This Service Information Bulletin announces a design change made to the rear bumper cover side mounting brackets. These new brackets provide increased clearance between the edges of the bumper cover and the corresponding quarter panels. Read More »
This bulletin announces availability of a new retaining plate and installation method to address gapping conditions which may develop between the front bumper cover and fender. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This bulletin announces a design change made to the rear bumper cover (face). To insure a proper fit of the new cover, the rear edge portion of the existing inner mud guards (splash shields) will need to be modified slightly in specific ... Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This document discusses some of the conditions that may trigger an Automatic Collision Notification (CAN) (Gen1) or Advanced Automatic Collision Notification (AACN) (Gen2), without a collision, airbag deployment, or accident taking place. Read More »
This Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINKA? Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin announces the recommended cleaning procedures to followed when encountering vehicles with long time exposure to pollen on painted surfaces on vehicles imported from Japan. This bulletin does not apply to SIA built vehicles. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed in this bulletin. Read More »
This Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINKA? Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer. Read More »
This bulletin provides a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this bulletin is to provide a desription of current changes to service manuals available via the Subaru Technical Information System (STIS) web site. Read More »
This Service Information Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2 Telematics system equipped Subaru. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2. Read More »
This bulletin provides an additional service procedure for replacing the pulsation dampers located on both low-pressure fuel delivery pipes as shown in the illustration below. Read More »
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool. Read More »
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case. Read More »
The purpose of this bulletin is to clarify the proper installation direction of the valve springs used on the FA engine. The springs have a light blue paint mark identifier as shown in the chart below. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. Read More »
This Service Information bulletin announces a change to the flywheel (pilot) bearing to a ?environmentally friendly? type which is compliant with the REACH (Registration, Evaluation, Authorization and restriction of CHemicals) ... Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This Service Information bulletin provides notice of an additional step to follow when diagnosing DTC P219A- ?Air-Fuel Ratio Imbalance (Bank 1)?. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. Read More »
Revised TSB. The Subaru Lock Information Site (SLIS) is located at http://lockinfo.subaru.com, and provides information on how to obtain immobilizer codes and key cut codes for Subaru vehicles from the 2000MY to present. Read More »
"THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH ... Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2. Read More »
This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation ?Gen 2? and ?Gen 2.1? F10 Navigation and Display Audio systems. Read More »
This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation ?Gen 2? and ?Gen 2.1? F10 Navigation and Display Audio systems. Read More »
Although Fujitsu TEN (F10) Navigation units utilize an externally (faceplate) accessible MicroSD memory card, the MicroSD card used in Clarion display audio units is internal and not accessible. Read More »
Revised TSB. Models with "Gen 2" F10 Audio/Navigation Systems. ?Gen 2? & ?Gen 2.1? Operating Tips. This bulletin provides information to help diagnose and address different s relating to customer concerns which may arise when ... Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6. Read More »
This Service Information bulletin provides notice of an additional step to follow when diagnosing DTC P219A- ?Air-Fuel Ratio Imbalance (Bank 1)?. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. Read More »
Revised TSB. The Subaru Lock Information Site (SLIS) is located at http://lockinfo.subaru.com, and provides information on how to obtain immobilizer codes and key cut codes for Subaru vehicles from the 2000MY to present. Read More »
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. Exchange order entry will now request a date and time when condition was last duplicated. Read More »
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed in this bulletin. Read More »
This Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINKA? Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer. Read More »
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2? display. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. Read More »
Revised TSB. The Subaru Lock Information Site (SLIS) is located at http://lockinfo.subaru.com, and provides information on how to obtain immobilizer codes and key cut codes for Subaru vehicles from the 2000MY to present. Read More »
"SPECIAL SERVICE TOOL SHIPMENT: BRZ WINDOW GLASS WRENCH STARTING THE WEEK OF AUGUST 24, 2015, SUBARU RETAILERS WILL RECEIVE A SPECIAL SERVICE TOOL FOR THE BRZ. Read More »
This bulletin announces availability of individual service parts and provides an installation procedure for the A/C compressor clutch assembly. Read More »
