Technical Service Bulletins (TSBs) for the 2014 BRZ are official communications between Subaru & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This bulletin announces a change made to the front lower control arm ball joint boots. The boot material has been changed to provide increased resistance to damage from ozone. Read More »
This bulletin announces a design change to the front strut mounts intended to address customer concerns of a popping-type sound which may be heard when making low speed turns. Read More »
This service Information bulletin provides precautions to follow when servicing the Brembo brake calipers utilized on the models listed. Because of their aluminum construction, it is critcal to take extra care when servicing. Read More »
This bulletin announces availability of a new stop lamp switch for the models listed above equipped with LED - type rear combination lamps. Read More »
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. Read More »
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. Read More »
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. Read More »
SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. Read More »
The purpose of this bulletin is to clarify the proper installation direction of the valve springs used on the FA engine. The springs have a light blue paint mark identifier as shown in the chart below. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. Read More »
This Service Information Bulletin announces design changes made to the ignition coil and engine wiring harness in response to a limited number of cases related to the ignition coil primary / secondary DTCs listed above. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
"THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH ... Read More »
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE INFORMATION REGARDING A HIGH-PITCHED ?CHIRP?, ?SQUEAK? OR ?CRICKET? SOUND YOU MAY HEAR COMING FROM THE ENGINE?S HIGH-PRESSURE FUEL PUMP. NOT ALL PUMPS MAY EXHIBIT THIS CONDITION. Read More »
HIGH-PITCHED ?CHIRP?, ?SQUEAK? OR ?CRICKET? SOUND FROM THE ENGINE - THE PURPOSE OF THIS BULLETIN IS TO PROVIDE INFORMATION REGARDING A HIGH-PITCHED ?CHIRP?, ?SQUEAK? OR ?CRICKET? SOUND YOU MAY HEAR COMING FROM THE ENGINE?S HIGH-PRESSURE ... Read More »
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE INFORMATION REGARDING A HIGH-PITCHED ?CHIRP?, ?SQUEAK? OR ?CRICKET? SOUND YOU MAY HEAR COMING FROM THE ENGINE?S HIGH-PRESSURE FUEL PUMP. NOT ALL PUMPS MAY EXHIBIT THIS CONDITION. Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed in this bulletin. Read More »
This Service Information Bulletin announces design changes made to the ignition coil and engine wiring harness in response to a limited number of cases related to the ignition coil primary / secondary DTCs listed. Read More »
The purpose of this bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed below: There are six areas that should be closely inspected if an oil leak is reported by the ... Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
This Service Information bulletin announces a change to the flywheel (pilot) bearing to a ?environmentally friendly? type which is compliant with the REACH (Registration, Evaluation, Authorization and restriction of CHemicals) ... Read More »
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. Read More »
This Service Information bulletin announces a design change to the internal contact portion of the oil pressure switch to increase durability Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched "chirp", "squeak" or "cricket" sound heard coming from the engine's Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
This bulletin provides a procedure to address customer concerns of a high-pitched ?chirp?, ?squeak? or ?cricket? sound heard coming from the engine?s Direct Injection (DI) high-pressure fuel pump. Not all DI pumps may exhibit this sound. Read More »
HIGH-PITCHED ?CHIRP?, ?SQUEAK? OR ?CRICKET? SOUND FROM THE ENGINE - THE PURPOSE OF THIS BULLETIN IS TO PROVIDE INFORMATION REGARDING A HIGH-PITCHED ?CHIRP?, ?SQUEAK? OR ?CRICKET? SOUND YOU MAY HEAR COMING FROM THE ENGINE?S HIGH-PRESSURE ... Read More »
This bulletin provides an additional service procedure for replacing the pulsation dampers located on both low-pressure fuel delivery pipes as shown in the illustration below. Read More »
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE INFORMATION REGARDING A HIGH-PITCHED ?CHIRP?, ?SQUEAK? OR ?CRICKET? SOUND YOU MAY HEAR COMING FROM THE ENGINE?S HIGH-PRESSURE FUEL PUMP. NOT ALL PUMPS MAY EXHIBIT THIS CONDITION. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. Read More »
This bulletin has been developed to outline the steps for gathering basic essential information during diagnosis and repair of the Infotainment concerns. (Applicable to all models with Harman or Denso CP1 Infotainment). Read More »
This Service Information Bulletin announces design changes made to the ignition coil and engine wiring harness in response to a limited number of cases related to the ignition coil primary / secondary DTCs listed. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
This bulletin announces availability of a new stop lamp switch for the models listed above equipped with LED - type rear combination lamps. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin announces availability of individual service parts and provides an installation procedure for the A/C compressor clutch assembly. Read More »
Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Read More »
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
All 2012 to 2015 Models Equipped with Fujitsu Ten (F10) Generation 1 (Gen1) Audio / Navigation Systems. This bulletin announces a new procedure for updating the operating software used in F10 Gen1 audio / navigation systems. Read More »
THIS SERVICE INFORMATION BULLETIN CONTAINS A SERIES OF SCREEN SHOTS WITH INSTRUCTIONS WHICH PROVIDE A PROCEDURE FOR PAIRING ANDROID SMARTPHONES TO BLUETOOTH-EQUIPPED CLARION AUDIO UNITS. Read More »
Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Read More »
THIS BULLETIN ANNOUNCES AVAILABILITY OF A REVISED TRUNK WEATHERSTRIP AND RUBBER STOPPERS DESIGNED TO ABSORB IMPACT AND PREVENT CONTACT OR IN RARE OCCURRENCES, DAMAGE TO THE REAR COMBINATION LAMPS WHEN CLOSING THE TRUNK LID. Read More »
Cracked Rear Combination Lamps - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these TSBs have been combined into TSB ... Read More »
Design Change to Rear Combination Lamps to Prevent Insect Intrusion - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these ... Read More »
Cracked Rear Combination Lamps - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these TSBs have been combined into TSB ... Read More »
Design Change to Rear Combination Lamps to Prevent Insect Intrusion - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these ... Read More »
Rear Combination Lamp and Related Enhancements - Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Read More »
COUNTERMEASURES FOR FROZEN POWER WINDOWS - THIS BULLETIN PROVIDES INFORMATION FOR 3 COUNTERMEASURES TO ADDRESS CONCERNS REGARDING POWER WINDOW OPERATION DURING COLD WEATHER WHEN THE DOOR GLASS MAY BECOME FROZEN TO THE OUTER WEATHERSTRIP. Read More »
This bulletin announces the availability of reprogramming files to address customer concerns of engine idle RPM decrease / instability when the A/C system cycles off and extended engine cranking. Read More »
This Service Information Bulletin announces a design change made to the rear bumper cover side mounting brackets. These new brackets provide increased clearance between the edges of the bumper cover and the corresponding quarter panels. Read More »
This bulletin announces availability of a new retaining plate and installation method to address gapping conditions which may develop between the front bumper cover and fender. Read More »
This bulletin provides a service procedure to address a small number of reports involving water leaking into the interior and collecting in the passenger's front floor area. Read More »
Design Change to Rear Combination Lamps to Prevent Insect Intrusion - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these ... Read More »
Rear Combination Lamp and Related Enhancements - Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Read More »
Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Read More »
Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
This bulletin provides a service procedure to address a small number of reports involving water leaking into the interior and collecting in the passenger's front floor area. Read More »
This bulletin announces a design change made to the rear bumper cover (face). To insure a proper fit of the new cover, the rear edge portion of the existing inner mud guards (splash shields) will need to be modified slightly in specific ... Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully. Read More »
DOOR LATCH / ACTUATOR FREEZING - THIS BULLETIN PROVIDES A REPAIR PROCEDURE TO PREVENT WATER FROM ACCUMULATING THEN FREEZING INSIDE THE DOOR LATCH / ACTUATOR ASSEMBLY IN COLD TEMPERATURES AND BINDING THE MECHANISM. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin announces the recommended cleaning procedures to followed when encountering vehicles with long time exposure to pollen on painted surfaces on vehicles imported from Japan. This bulletin does not apply to SIA built vehicles. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed in this bulletin. Read More »
This bulletin provides a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this bulletin is to provide a desription of current changes to service manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This bulletin provides an additional service procedure for replacing the pulsation dampers located on both low-pressure fuel delivery pipes as shown in the illustration below. Read More »
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool. Read More »
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case. Read More »
The purpose of this bulletin is to clarify the proper installation direction of the valve springs used on the FA engine. The springs have a light blue paint mark identifier as shown in the chart below. Read More »
This Service Information bulletin announces a change to the flywheel (pilot) bearing to a ?environmentally friendly? type which is compliant with the REACH (Registration, Evaluation, Authorization and restriction of CHemicals) ... Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
This Service Information bulletin provides notice of an additional step to follow when diagnosing DTC P219A- ?Air-Fuel Ratio Imbalance (Bank 1)?. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
Revised TSB. The Subaru Lock Information Site (SLIS) is located at http://lockinfo.subaru.com, and provides information on how to obtain immobilizer codes and key cut codes for Subaru vehicles from the 2000MY to present. Read More »
THIS BULLETIN ANNOUNCES A DESIGN CHANGE OF THE ROOF WEATHERSTRIP RETAINER/ MOLDING TO ADDRESS CUSTOMER CONCERNS OF A GROWLING SOUND WHICH MAY BE HEARD WHEN FULLY CLOSING THE DOOR GLASS. Read More »
"THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH ... Read More »
VIBRATION SOUND FROM HIGH-MOUNT STOP LAMP ASSEMBLY - THIS BULLETIN ANNOUNCES THE AVAILABILITY OF A NEW HIGH-MOUNT STOP LAMP ASSEMBLY DESIGNED TO ADDRESS A CUSTOMER CONCERN OF A VIBRATION-TYPE SOUND WHICH MAY BE HEARD WHILE DRIVING. Read More »
"WE HAVE RECEIVED SEVERAL CALLS FROM DEALERS WHO HAVE CUSTOMERS ELIGIBLE FOR THE WQH44 SUBARU CARPETED FLOOR MAT RECALL BUT DO NOT HAVE THE ORIGINAL MATS THAT WERE IN THE VEHICLE AT THE TIME OF SALE. Read More »
All 2012 to 2015 Models Equipped with Fujitsu Ten (F10) Generation 1 (Gen1) Audio / Navigation Systems. This bulletin announces a new procedure for updating the operating software used in F10 Gen1 audio / navigation systems. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
This Service Information bulletin provides notice of an additional step to follow when diagnosing DTC P219A- ?Air-Fuel Ratio Imbalance (Bank 1)?. Read More »
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site. Read More »
Revised TSB. The Subaru Lock Information Site (SLIS) is located at http://lockinfo.subaru.com, and provides information on how to obtain immobilizer codes and key cut codes for Subaru vehicles from the 2000MY to present. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. Read More »
THIS BULLETIN CONTAINS ILLUSTRATIONS OF EXCHANGE COMPONENTS AND THEIR MANUFACTURER AS WELL AS A DESCRIPTION OF THE PROPER EXCHANGE PROCEDURE. THE EXCHANGE PROGRAM POLICY CAN ALSO BE FOUND IN SECTIONS 8.4.9 AND 11.2. Read More »
THIS BULLETIN CONTAINS ILLUSTRATIONS OF EXCHANGE COMPONENTS AND THEIR MANUFACTURER AS WELL AS A DESCRIPTION OF THE PROPER EXCHANGE PROCEDURE. THE EXCHANGE PROGRAM POLICY CAN ALSO BE FOUND IN SECTIONS 8.4.9 AND 11.2. Read More »
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. Read More »
THIS BULLETIN CONTAINS ILLUSTRATIONS OF EXCHANGE COMPONENTS AND THEIR MANUFACTURER AS WELL AS A DESCRIPTION OF THE PROPER EXCHANGE PROCEDURE. THE EXCHANGE PROGRAM POLICY CAN ALSO BE FOUND IN SECTIONS 8.4.9 AND 11.2. Read More »
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the areas listed in this bulletin. Read More »
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2. Read More »
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. Read More »
Revised TSB. The Subaru Lock Information Site (SLIS) is located at http://lockinfo.subaru.com, and provides information on how to obtain immobilizer codes and key cut codes for Subaru vehicles from the 2000MY to present. Read More »
"SPECIAL SERVICE TOOL SHIPMENT: BRZ WINDOW GLASS WRENCH STARTING THE WEEK OF AUGUST 24, 2015, SUBARU RETAILERS WILL RECEIVE A SPECIAL SERVICE TOOL FOR THE BRZ. Read More »
This bulletin announces availability of individual service parts and provides an installation procedure for the A/C compressor clutch assembly. Read More »
"THIS BULLETIN WILL ADDRESS CUSTOMER CONCERNS OF AN UNEVEN GAP APPEARING BETWEEN THE TOP OF THE CENTER DASH AIR VENT GRILLE AND THE INSTRUMENT PANEL DASH PAD DIRECTLY ABOVE IT. Read More »
