Technical Service Bulletins (TSBs) for the 2010 Santa Fe are official communications between Hyundai & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
The warranty coverage for the clock spring has been extended to 15 years with unlimited mileage from the date of original retail delivery or date of first use, whichever occurs first. Read More »
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years. Read More »
HYUNDAI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. 2010-2011 SANTA FE. FRONT COIL SPRING INSTALLATION. *RM UPDATED 10/28/11. *PE UPDATED 1/25/12. *PE Read More »
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). Read More »
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). Read More »
HYUNDAI: CHECK ENGINE LIGHT ON, TRANSAXLE HELD IN THIRD GEAR, AND TROUBLE CODES STORED. THIS IS CAUSED BY INCORRECT INPUT AND OUTPUT SPEED SENSORS. *RM Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). Read More »
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness Read More »
HYUNDAI: DUE TO AN IMPROPERLY ADJUSTED OR IMPROPERLY OPERATING INHIBITOR SWITCH (RANGE SWITCH), ON SOME VEHICLES, RESULTED IN RANGE SWITCH SENSOR CIRCUIT (P0705), OPEN CIRCUIT (P0707), SWITCH RANGE/PERFORMANCE (P0706), SHORT CIRCUIT OR ... Read More »
HYUNDAI: THE THROTTLE CONTROL (ETC) BODY, ON SOME VEHIICLES, NEEDS TO BE CLEANED AND PROCEDURAL INFORMATION IS BEING PROVIDED, DUE TO DEPOSITS FOUND AT VALVE-TO-BORE INTERFACE. Read More »
A class action lawsuit against Hyundai Motor America (a??HMAa??) alleges that certain Hyundai vehicles (a??Class Vehiclesa??) were manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine ... Read More »
The warranty coverage for engine repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, ... Read More »
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Read More »
Certain vehicles may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. Read More »
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement. Read More »
Certain vehicles that have completed Service Campaign 966 may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Read More »
Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Read More »
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original ... Read More »
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Read More »
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original ... Read More »
Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
HYUNDAI: THIS BULLETIN PROVIDES INFORMATION RELATED TO ECM SOFTWARE UPDATE OF SOME 3.5L VEHICLES THAT MAY EXPERIENCE CHECK ENGINE LIGHT ON. *JS Read More »
HYUNDAI: INTERMEDIATE SHAFT NOISE. PROVIDES A PROCEDURE THAT WILL REPAIR OR PREVENT AN INTERMEDIATE SHAFT NOISE CONDITION ON CERTAIN VEHICLES WITH 2.4L ENGINES WITH AUTOMATIC TRANSMISSIONS BUILT BETWEEN 10/15/09-03/05/10. Read More »
HYUNDAI: ECM UPDATE-MIL ON WITH DTC P0454. PROVIDES INFORMATION RELATED TO THE ECM SOFTWARE UPDATE OF VEHICLES WHICH MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATED WITH ECM (ELECTRONIC CONTROL MODULE) SYSTEM RELATED DTC P0454 ... Read More »
Certain vehicles may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Read More »
Certain vehicles may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. Read More »
ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. Read More »
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. Read More »
HYUNDAI: THE THROTTLE CONTROL (ETC) BODY, ON SOME VEHIICLES, NEEDS TO BE CLEANED AND PROCEDURAL INFORMATION IS BEING PROVIDED, DUE TO DEPOSITS FOUND AT VALVE-TO-BORE INTERFACE. Read More »
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear). Read More »
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear). Read More »
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition. Read More »
AUTOMATIC TRANSAXLE (6-SPEED) ATM FLUID LEVEL CHECK Description: The following vehicles are equipped with a 6-speed automatic transmission. Read More »
THE SHIFT LEVER ON SOME 6-SPEED VEHICLES MAY INTERMITTENTLY NOT SHIFT OUT OF PARK. THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION. Read More »
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition. Read More »
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness Read More »
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time. Read More »
HYUNDAI: PROCEDURE INFORMATION REGARDING THE UPDATE SOFTWARE FOR 4WD OF AUTOMATIC TRANSAXLE ELECTRONIC CONTROL UNIT (ECU) ON SOME VEHICLES. MODEL 2010-2012 SANTA FE. *PE Read More »
HYUNDAI: DUE TO AN IMPROPERLY ADJUSTED OR IMPROPERLY OPERATING INHIBITOR SWITCH (RANGE SWITCH), ON SOME VEHICLES, RESULTED IN RANGE SWITCH SENSOR CIRCUIT (P0705), OPEN CIRCUIT (P0707), SWITCH RANGE/PERFORMANCE (P0706), SHORT CIRCUIT OR ... Read More »
HYUNDAI: INFORMATION HAS BEEN PROVIDED REGARDING PROCEDURE IN REPAIRING AND REPLACING RELATED PART TO TRANSMISSION SOLENOID DTC FOR CERTAIN VEHICLES. Read More »
HYUNDAI: ATM INPUT AND OUTPUT SPEED SENSOR DTC P0717, P0721 AND P0722. DO NOT REPLACE TRANSMISSION FOR THE DTC. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE RELATED PART. ALSO INCLUDED MODEL AZERA MODEL YEAR 2012. Read More »
HYUNDAI: OPERATION OF THE TRANSMISSION SOLENOID MAY LEAD TO CHECK ENGINE LIGHT, TRANSAXLE HELD IN 4TH GEAR SAFE, AND DIAGNOSTIC TROUBLE CODES. *RM Read More »
HYUNDAI: INTERMEDIATE SHAFT NOISE. PROVIDES A PROCEDURE THAT WILL REPAIR OR PREVENT AN INTERMEDIATE SHAFT NOISE CONDITION ON CERTAIN VEHICLES WITH 2.4L ENGINES WITH AUTOMATIC TRANSMISSIONS BUILT BETWEEN 10/15/09-03/05/10. Read More »
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
HYUNDAI: DUE TO AN ERROR IN THE INTERNAL CONTROL MODULE READ ONLY MEMORY, INFORMATION IS PROVIDED REGARDING THE REPLACING OF THE PCM AND A POSSIBLE WARRANTY CLAIM. Read More »
Before installing an automatic transmission, check the depth of the torque converter in the case to confirm the torque converter is fully installed in the transmission. If this is not done, the oil pump may be damaged. Read More »
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Read More »
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. Read More »
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
HYUNDAI: TO HELP PROTECT BATTERY FROM OVERCHARGING, AN ELECTRICAL POWER MANAGEMENT FEATURE TO REGULATE ALTERNATOR LOAD, AND PLACES ON ENGINE TO MAXIMIZE EFFICIENCY. MODEL 2010-2012 SANTA FE. Read More »
THIS BULLETIN DESCRIBES THE PROCEDURE TO VERIFY THAT THE FUSE AND JUMPER SETTINGS FOR THE REMOTE ENGINE START CONTROL MODULE ARE SET FOR THE APPLICABLE VEHICLE, AND IF NECESSARY, HOW TO MAKE ADJUSTMENTS TO THESE SETTINGS. Read More »
HYUNDAI: INFORMATION HAS BEEN PROVIDED REGARDING PROCEDURE IN REPAIRING AND REPLACING RELATED PART TO TRANSMISSION SOLENOID DTC FOR CERTAIN VEHICLES. Read More »
SUBARU: BLUETOOTH CONTROLS ON STEERING WHEEL INOPERATIVE. THE BLUETOOTH CONTROLS ON THE STEERING WHEEL DO NOT OPERATE, A COUNTERMEASURE WIRING HARNESS IS NOW AVAILABLE TO REMEDY THE CONDITION. Read More »
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. Read More »
HYUNDAI: 2010-2012 SANTA FE : SERVICE BULLETIN PROVIDES INFORMATION REGARDING ECM SOFTWARE UPDATE FOR CERTAIN 3.5L VEHICLES TO CORRECT THE MALFUNCTION INDICATOR LAMP ILLUMINATION. *LJ Read More »
HYUNDAI: PROCEDURE INFORMATION REGARDING THE UPDATE SOFTWARE FOR 4WD OF AUTOMATIC TRANSAXLE ELECTRONIC CONTROL UNIT (ECU) ON SOME VEHICLES. MODEL 2010-2012 SANTA FE. *PE Read More »
HYUNDAI: ECM UPDATE. (CAMPAIGN TC7). PROVIDES INFORMATION RELATED TO AN ECM SOFTWARE UPDATE TO SOME VEHICLES TO REVISE LOGIC FOR DTC P0111 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT RANGE/PERFORMANCE. Read More »
HYUNDAI: ECM UPDATE-MIL ON WITH DTC P0454. PROVIDES INFORMATION RELATED TO THE ECM SOFTWARE UPDATE OF VEHICLES WHICH MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATED WITH ECM (ELECTRONIC CONTROL MODULE) SYSTEM RELATED DTC P0454 ... Read More »
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
The warranty coverage for the clock spring has been extended to 15 years with unlimited mileage from the date of original retail delivery or date of first use, whichever occurs first. Read More »
HYUNDAI: SRS CONTROL MODULE ROLLOVER SENSOR. A ROLLOVER SENSOR HAS BEEN INCORPORATED INTO THE SRS CONTROL MODULE (SRSCM) BEGINNING WITH THE 2010 MODEL YEAR SANTA FE AND TUCSON. Read More »
HYUNDAI: SRS CONTROL MODULE ROLLOVER SENSOR. A ROLLOVER SENSOR HAS BEEN INCORPORATED INTO THE SRS CONTROL MODULE (SRSCM) BEGINNING WITH THE 2010 MODEL YEAR SANTA FE AND TUCSON. Read More »
HYUNDAI: SRS CONTROL MODULE ROLLOVER SENSOR. A ROLLOVER SENSOR HAS BEEN INCORPORATED INTO THE SRS CONTROL MODULE (SRSCM) BEGINNING WITH THE 2010 MODEL YEAR SANTA FE AND TUCSON. Read More »
In some areas, a vehicle's underbody may exhibit corrosion due to road salt usage. As a precautionary measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the ... Read More »
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. Read More »
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail ... Read More »
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). Read More »
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products. Read More »
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition. Read More »
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time. Read More »
HYUNDAI: LABEL REQUIREMENTS FOR VEHICLE LOADING TO COMPLY WITH FMVSS 110. EFFECTIVE 6/2/08, FMVSS 110 (FMVSS 110) SETS A THRESHOLD FOR CORRECTING LOAD CAPACITY INFORMATION INDICATED ON TIRE PLACARDS WHEN VEHICLE WEIGHT HAS BEEN ... Read More »
The warranty coverage for engine repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, ... Read More »
Certain vehicles may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. Read More »
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Read More »
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness Read More »
In some areas, a vehicle?s underbody may exhibit corrosion due to road salt usage. As a precautionary measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the ... Read More »
