- November 24: Hyundai ICCU Failures Cause Second Recall recalls | 0 days ago
- October 25: Hyundai and Kia Theft Settlement Final news | 30 days ago
- October 8: Enel X Way Closure and JuiceBox Charger Fires Investigated investigations | 47 days ago
- September 22: Hyundai Recalls 2025 Tucsons Over Missing Labels recalls | 63 days ago
- September 18: Hyundai IVT (Intelligent Variable Transmission) Reliability Questioned news | 67 days ago
2014 Hyundai Genesis Coupe
112 Technical Service Bulletins (TSBs)
TSB List for the 2014 Hyundai Genesis Coupe
Technical Service Bulletins (TSBs) for the 2014 Genesis Coupe are official communications between Hyundai & their dealerships that describe processes for troubleshooting or fixing certain common problems. All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
SUSPENSION
-
TSB #20-SS-001H
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years. Read More »
BRAKES (PWS)
-
TSB #21-BR-002H
This bulletin provides best practice recommendations when performing brake service procedures. Read More »
-
TSB #20-BR-002H
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area. Read More »
ENGINE (PWS)
-
TSB #19-EM-001H
This bulletin provides information regarding the changes in the timing chain and the crankshaft sprockets on certain Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3. Read More »
-
TSB #19-AT-008H
When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the related solenoid and E-module. Read More »
-
TSB #19-AT-005H
If you are servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the E-module. Read More »
ENGINE AND ENGINE COOLING
-
TSB #23-EM-005H
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services. Read More »
-
TSB #22-01-024H-2
OP CODE/PART NUMBER (REFERENCE GUIDE FOR SERVICE CAMPAIGN T6G) Read More »
-
TSB #22-EM-010H
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement. Read More »
-
TSB #21-EM-004H
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
-
TSB #21-EM-003H
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
-
TSB #22-01-024H-2
OP CODE/PART NUMBER (REFERENCE GUIDE FOR SERVICE CAMPAIGN T6G) Read More »
ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR
-
TSB #22-01-024H-2
OP CODE/PART NUMBER (REFERENCE GUIDE FOR SERVICE CAMPAIGN T6G) Read More »
FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY
-
TSB #24-FL-001G
This bulletin outlines the basic components of the BG Fuel Test Kit and the procedure to test the quality of the fuel during vehicle diagnosis. Read More »
POWER TRAIN
-
TSB #24-AT-002H
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2. Read More »
-
TSB #23-01-014H-5
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai ... Read More »
-
TSB #21-AT-018H
This bulletin describes the procedure to replace the 35R and 4&OD solenoids for a shift flare and/or harsh shift during the 2~3, 3~4 or 4~5 upshift. Read More »
-
TSB #20-AT-016H
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
-
TSB #19-AT-021H-1
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
-
TSB #19-EM-001H
This bulletin provides information regarding the changes in the timing chain and the crankshaft sprockets on certain Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3. Read More »
-
TSB #19-AT-014H
This bulletin provides a procedure to diagnose an 8-speed automatic transaxle with a harsh and/or delayed shift using GDS. Read More »
-
TSB #19-AT-011H
The procedure describes the procedure to check the ATF level for 8-speed Rear-Wheel-Drive vehicles. Read More »
-
TSB #19-AT-007H
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. Read More »
-
TSB #19-FL-003H
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
-
TSB #19-AT-008H
When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the related solenoid and E-module. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION
-
TSB #19-AT-011H
The procedure describes the procedure to check the ATF level for 8-speed Rear-Wheel-Drive vehicles. Read More »
-
TSB #19-AT-007H
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. Read More »
-
TSB #19-AT-008H
When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the related solenoid and E-module. Read More »
-
TSB #5NP-H3D9Z-03
The following vehicles are equipped with an 8-speed automatic transmission. The ATF level can be checked by the procedure shown below. Read More »
-
TSB #5NP-J4N8R-01
DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE. Read More »
-
TSB #5NP-D2Y6N-12
"UPDATE THE WARRANTY INFORMATION. DESCRIPTION: DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED BELOW. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE." Read More »
-
TSB #5NP-W7J6Y-11
"AUTOMATIC TRANSMISSION SOLENOID & SENSOR REPLACEMENT FOR DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841" Read More »
-
TSB #5NP-Q9X6P-10
THIS BULLETIN PROVIDES A PROCEDURE TO TRANSFER PRESSURE DATA TO THE TCM USING GDS MOBILE. THIS PROCEDURE IS NECESSARY TO REDUCE THE TCM LEARNING TIME AND IMPROVE THE SHIFT QUALITY. Read More »
-
TSB #14-AT-007
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
-
TSB #5NP-B6E2P-10
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES
-
TSB #5NP-H3D9Z-03
The following vehicles are equipped with an 8-speed automatic transmission. The ATF level can be checked by the procedure shown below. Read More »
POWER TRAIN:AXLE ASSEMBLY
-
TSB #5NP-B6E2P-10
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
ELECTRICAL SYSTEM
-
TSB #24-01-009H
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in ... Read More »
-
TSB #24-01-009H
This bulletin provides the service procedure to: 1) Upgrade the IBU/BCM (Integrated Body Control Unit/Body Control Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft ... Read More »
-
TSB #24-01-009H
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in ... Read More »
-
TSB #23-01-014H-6
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in ... Read More »
-
TSB #23-01-014H-6
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in ... Read More »
-
TSB #23-01-014H-6
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
-
TSB #23-01-014H-6
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai ... Read More »
-
TSB #23-01-014H-5
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai ... Read More »
-
TSB #23-BE-010H
Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. Read More »
-
TSB #23-01-014H-5
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai ... Read More »
-
TSB #23-01-014H-5
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
-
TSB #23-01-014H-5
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
-
TSB #23-01-014H-4
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
-
TSB #23-01-014H-4
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. Read More »
-
TSB #23-01-014H-4
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
-
TSB #20-EE-003H
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
-
TSB #20-BE-001H
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. Read More »
-
TSB #19-BE-010H
This bulletin provides information related to clearing all Diagnostic codes for vehicles equipped with the Blue Link system (Gen 1). Read More »
-
TSB #19-FL-003H
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:CONTROL MODULE
-
TSB #24-01-009H
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in ... Read More »
-
TSB #23-01-014H-6
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai ... Read More »
-
TSB #23-01-014H-5
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai ... Read More »
-
TSB #23-01-014H-5
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:IMMOBILIZER/PROXIMITY:SENSOR
-
TSB #23-01-014H-6
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
-
TSB #23-01-014H-5
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
-
TSB #23-01-014H-4
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. Read More »
-
TSB #23-01-014H-4
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:IMMOBILIZER/PROXIMITY:KEY/SENDER
-
TSB #23-01-014H-5
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system ... Read More »
ELECTRICAL SYSTEM:SOFTWARE
-
TSB #14-BE-016
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #14-FL-005
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #14-01-029
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #14-BE-005
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
EXTERIOR LIGHTING
-
TSB #20-BD-014H
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
VISIBILITY
-
TSB #24-BD-001H
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. Read More »
-
TSB #23-BD-002H
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
-
TSB #19-BE-004H
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Read More »
VISIBILITY/WIPER (PWS)
-
TSB #24-BD-001H
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. Read More »
VISIBILITY:REARVIEW MIRRORS/DEVICES
-
TSB #19-BE-004H
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Read More »
AIR BAGS
-
TSB #5NP-P4Q3W-11
THE HYUNDAI GENESIS COUPE IS EQUIPPED WITH AN OCCUPANT CLASSIFICATION SYSTEM (OCS) TO DETERMINE IF THE FRONT PASSENGER SEAT IS OCCUPIED, AND IF SO, DETECT THE PRESENCE OF A CHILD RESTRAINT SYSTEM OR SMALL STATURED OCCUPANT. Read More »
AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE
-
TSB #5NP-P4Q3W-11
THE HYUNDAI GENESIS COUPE IS EQUIPPED WITH AN OCCUPANT CLASSIFICATION SYSTEM (OCS) TO DETERMINE IF THE FRONT PASSENGER SEAT IS OCCUPIED, AND IF SO, DETECT THE PRESENCE OF A CHILD RESTRAINT SYSTEM OR SMALL STATURED OCCUPANT. Read More »
AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
-
TSB #5NP-P4Q3W-11
THE HYUNDAI GENESIS COUPE IS EQUIPPED WITH AN OCCUPANT CLASSIFICATION SYSTEM (OCS) TO DETERMINE IF THE FRONT PASSENGER SEAT IS OCCUPIED, AND IF SO, DETECT THE PRESENCE OF A CHILD RESTRAINT SYSTEM OR SMALL STATURED OCCUPANT. Read More »
STRUCTURE
-
TSB #23-01-034H
In certain areas, a vehiclea??s underbody may exhibit corrosion due to road-salt usage. As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to ... Read More »
-
TSB #23-01-034H
In some areas, a vehiclea??s underbody may exhibit corrosion due to road salt usage. As a preventative measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the ... Read More »
STRUCTURE:BODY
-
TSB #23-BD-007H
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. Read More »
VEHICLE SPEED CONTROL
-
TSB #5NP-J4N8R-01
DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE. Read More »
TIRES
-
TSB #22-GI-006H
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail ... Read More »
-
TSB #20-SS-004H
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. Read More »
-
TSB #20-SS-002H(1)
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
WHEELS
-
TSB #20-SS-004H
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. Read More »
-
TSB #20-SS-002H(1)
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
SEATS
-
TSB #5NP-P4Q3W-11
THE HYUNDAI GENESIS COUPE IS EQUIPPED WITH AN OCCUPANT CLASSIFICATION SYSTEM (OCS) TO DETERMINE IF THE FRONT PASSENGER SEAT IS OCCUPIED, AND IF SO, DETECT THE PRESENCE OF A CHILD RESTRAINT SYSTEM OR SMALL STATURED OCCUPANT. Read More »
LANE DEPARTURE
-
TSB #19-BE-011H-1
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
BACK OVER PREVENTION
-
TSB #19-BE-011H-1
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
BACK OVER PREVENTION: CAMERA SYSTEM
-
TSB #14-BE-001
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
EQUIPMENT
-
TSB #22-GI-006G
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) sets a threshold for correcting load capacity information indicated on tire placards when the vehicle weight has been increased before retail sale. Read More »
-
TSB #21-EM-004H
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
-
TSB #21-BR-002H
This bulletin provides best practice recommendations when performing brake service procedures. Read More »
-
TSB #21-EM-003H
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below. Read More »
-
TSB #20-BD-014H
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
-
TSB #20-BD-007H-1
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products. Read More »
-
TSB #20-EE-003H
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
-
TSB #19-AT-021H-1
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
-
TSB #19-AT-007H
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. Read More »
-
TSB #14-AT-007
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES
-
TSB #24-01-009H
This bulletin provides the service procedure to: 1) Upgrade the IBU/BCM (Integrated Body Control Unit/Body Control Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft ... Read More »
-
TSB #24-01-009H
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in ... Read More »
EQUIPMENT:OTHER:LABELS
-
TSB #22-GI-006G
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) sets a threshold for correcting load capacity information indicated on tire placards when the vehicle weight has been increased before retail sale. Read More »
EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
-
TSB #20-AT-016H
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
-
TSB #5NP-J4N8R-01
DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE. Read More »
EQUIPMENT ADAPTIVE/MOBILITY
-
TSB #21-BR-002H
This bulletin provides best practice recommendations when performing brake service procedures. Read More »
-
TSB #20-BD-014H
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
-
TSB #20-AT-016H
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
-
TSB #20-BD-007H
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products. Read More »
-
TSB #19-GI-006H
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Read More »
-
TSB #19-GI-006H
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Read More »