Technical Service Bulletins (TSBs) for the 2011 Azera are official communications between Hyundai & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness Read More »
HYUNDAI: DUE TO AN IMPROPERLY ADJUSTED OR IMPROPERLY OPERATING INHIBITOR SWITCH (RANGE SWITCH), ON SOME VEHICLES, RESULTED IN RANGE SWITCH SENSOR CIRCUIT (P0705), OPEN CIRCUIT (P0707), SWITCH RANGE/PERFORMANCE (P0706), SHORT CIRCUIT OR ... Read More »
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement. Read More »
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2. Read More »
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear). Read More »
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear). Read More »
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition. Read More »
AUTOMATIC TRANSAXLE (6-SPEED) ATM FLUID LEVEL CHECK Description: The following vehicles are equipped with a 6-speed automatic transmission. Read More »
THE SHIFT LEVER ON SOME 6-SPEED VEHICLES MAY INTERMITTENTLY NOT SHIFT OUT OF PARK. THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION. Read More »
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition. Read More »
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness Read More »
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time. Read More »
HYUNDAI: DUE TO AN IMPROPERLY ADJUSTED OR IMPROPERLY OPERATING INHIBITOR SWITCH (RANGE SWITCH), ON SOME VEHICLES, RESULTED IN RANGE SWITCH SENSOR CIRCUIT (P0705), OPEN CIRCUIT (P0707), SWITCH RANGE/PERFORMANCE (P0706), SHORT CIRCUIT OR ... Read More »
HYUNDAI: INFORMATION HAS BEEN PROVIDED REGARDING PROCEDURE IN REPAIRING AND REPLACING RELATED PART TO TRANSMISSION SOLENOID DTC FOR CERTAIN VEHICLES. Read More »
HYUNDAI: ATM INPUT AND OUTPUT SPEED SENSOR DTC P0717, P0721 AND P0722. DO NOT REPLACE TRANSMISSION FOR THE DTC. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE RELATED PART. ALSO INCLUDED MODEL AZERA MODEL YEAR 2012. Read More »
HYUNDAI: OPERATION OF THE TRANSMISSION SOLENOID MAY LEAD TO CHECK ENGINE LIGHT, TRANSAXLE HELD IN 4TH GEAR SAFE, AND DIAGNOSTIC TROUBLE CODES. *RM Read More »
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
Before installing an automatic transmission, check the depth of the torque converter in the case to confirm the torque converter is fully installed in the transmission. If this is not done, the oil pump may be damaged. Read More »
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. Read More »
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
HYUNDAI: INFORMATION HAS BEEN PROVIDED REGARDING PROCEDURE IN REPAIRING AND REPLACING RELATED PART TO TRANSMISSION SOLENOID DTC FOR CERTAIN VEHICLES. Read More »
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. Read More »
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail ... Read More »
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products. Read More »
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition. Read More »
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time. Read More »
HYUNDAI: LABEL REQUIREMENTS FOR VEHICLE LOADING TO COMPLY WITH FMVSS 110. EFFECTIVE 6/2/08, FMVSS 110 (FMVSS 110) SETS A THRESHOLD FOR CORRECTING LOAD CAPACITY INFORMATION INDICATED ON TIRE PLACARDS WHEN VEHICLE WEIGHT HAS BEEN ... Read More »
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
If you are servicing an applicable vehicle with a a??Check Enginea?? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. Read More »
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Read More »
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Read More »
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness Read More »
