Technical Service Bulletins (TSBs) for the 2006 Savana are official communications between GMC & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section. Read More »
BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE AND HUMMER: INFORMATION ON PITMAN ARM SHAFT SEAL SERVICE KIT. DO NOT REPLACE ENTIRE STEERING GEAR FOR PITMAN SEAL LEAK. Read More »
BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE AND HUMMER: INFORMATION ON PITMAN ARM SHAFT SEAL SERVICE KIT. DO NOT REPLACE ENTIRE STEERING GEAR FOR PITMAN SEAL LEAK. Read More »
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section. Read More »
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This preliminary informational bulletin provides repair information on installing a reinforcement to correct a customer concern that a crack has developed on the spring mount area of the front shock absorber mounting bracket. Read More »
GM: 2006-2011 EXPRESS/SAVANA. A CRACK IN A WELD IS CAUSING THE FRONT SHOCK ABSORBER TOWER TO SEPARATE FROM THE FRAME. *RM UPDATED 9/10/12. *PE Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
GM: THERE IS A NOISE FROM THE REAR OF THE VEHICLE DURING ACCELERATION AND IS FROM METAL TO METAL CONTACT OF BUSHINGS. 2006-2012 EXPRESS/SAVANA. *RM Read More »
GM: THERE IS A NOISE FROM THE REAR OF THE VEHICLE DURING ACCELERATION AND IS FROM METAL TO METAL CONTACT OF BUSHINGS. 2006-2012 EXPRESS/SAVANA. *RM Read More »
SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY:SHACKLE
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HYDRO-BOOST IS NOT SERVICEABLE AND WILL NEED TO BE REPLACED IF THE BRAKE PEDAL MOVES OR APPLIES ON ITS OWN AT A FULL TURN. Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP
ANTI-LOCK BRAKING SYSTEM (ABS) LIGHT ON SPEEDOMETER MAY BE ERRATIC. DIAGNOSTIC TROUBLE CODE (DTC) C0055 C0235 C0236 OR C0237 STORED IN THE EBCM. *TT 1998-2008 ALL CHEVROLET, GMC, BUICK, AND OLDSMOBILE MID-SIZED TRUCKS AND UTILITIES. Read More »
This Preliminary Information communication provides information to the technician that some vehicles may have an Antilock Braking System/ Traction Control System Malfunction Indicator Lamp are on or other various electrical issues. Read More »
ANTI-LOCK BRAKING SYSTEM (ABS) LIGHT ON SPEEDOMETER MAY BE ERRATIC. DIAGNOSTIC TROUBLE CODE (DTC) C0055 C0235 C0236 OR C0237 STORED IN THE EBCM. *TT 1998-2008 ALL CHEVROLET, GMC, BUICK, AND OLDSMOBILE MID-SIZED TRUCKS AND UTILITIES. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. Read More »
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. Read More »
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. Read More »
This informational bulletin provides technicians with information to help educate them on the many various combinations of engines, interfacing equipment and vehicle usage which may cause higher than expected oil consumption. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
GMC/CHEVROLET: ENGINES, WITH EGR SYSTEM, HAS LEAKAGE FROM EGR COOLER ENGINE COOLANT INTO THE COMBUSTION CHAMBER. MODEL 2002-15 SILVERADO, SIERRA, 2004-09 KODIAK C4500-C5500, TOPKICK C4500-C5500, 2006-15 EXPRESS, SAVANA. Read More »
This informational bulletin provides additional information on identifying duramax aftermarket power up devices that may cause damage to the engine and not covered under warranty. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2A? or global diagnostic system 2 ... Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION FOR IDENTIFYING NON-GM ECM CALIBRATION USE AND POWER-UP HARDWARE DETECTION IN DURAMAX DIESEL ENGINES - PHOTOGRAPH TECH 2 CALIBRATION IDS, CALIBRATION VERIFICATION NUMBERS (CVNS) AND ... Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. Read More »
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. Read More »
This preliminary informational bulletin provides a diagnostic tip for coolant leak at oil cooler inlet pipe o-ring after service engine replacement. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils. Read More »
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils. Read More »
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Read More »
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2 Read More »
This informational bulletin provides Information on Identifying Duramax Diesel Overpower Engine Breakdown/Non-Function Due to Aftermarket Power-Up Devices vs Non Overpower Engine Non-Function of Pistons, Cylinders, Valvetrain Components, ... Read More »
GENERAL MOTORS: AN OPTIONAL ENGINE BLOCK HEATER PLUG IN FOR ONBOARD AC POWER AND WITH CONTINUOUS USAGE WILL RESULT IN SHORTING OF WIRES, OVER HEATING SYSTEM, ELECTRICAL FAILURE AND COMPARTMENT ENGINE FIRES. Read More »
BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. Read More »
GM: THERE IS AN INTERMITTENT ENGINE LIGHT ON DUE TO FIVE POSSIBLE INTERNAL TROUBLE CODES. THERE MAY ALSO BE AN EXTENDED CRANK AFTER FILLING THE FUEL TANK. *RM UPDATED 5/31/11. *PE UPDATED ON 06/16/2011. Read More »
LBZ, LLY, ENGINE WITH ROUGH IDLE, POOR PERFORMANCE, BLACK/WHITE EXHAUST SMOKE, MIL/SES LIGHT ON AND ONE OR MORE OF THE FOLLOWING DTC'S P003A, P060B, P0230, P0403, P0401, P0606, P2146, P2149, P2152, P2155. Read More »
OIL SEEPAGE FROM TURBO AIR CHARGE COOLER HOSES OR HOSE BLOWING OFF DURING ACCELERATION. POSSIBLE DIAGNOSTIC TROUBLE CODE P0299. *TT UPDATED 04-24-07. *KB Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramax? diesel engines ? Photograph Tech 2? Calibration IDs, Calibration Verification Numbers ... Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This informational bulletin provides information for Identifying Non-GM ECM Calibration Use and Power-up Hardware Detection in Duramax Diesel Engines - Photograph Tech 2 Calibration IDs, Calibration Verification Numbers (CVNs) and ... Read More »
GM: AN 'ENGINE POWER IS REDUCED' MESSAGE APPEARS AND THERE IS A STORED TROUBLE CODE. THIS IS CAUSED BY WEAR OF THE INTERNAL FUEL INJECTOR. *RM Read More »
GENERAL MOTORS: LBZ, LLY, LMM MIL/SES LIGHT N DTC P0087-FUEL RAIL PRESSURE (FRP) TOO LOW, LACK OF PERFORMANCE, NO POWER, ENGINE RUNS ROUGH, NO START (DIAGNOSE FUEL SYSTEM COMPONENTS). *PE UPDATED 3/1/10. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. Read More »
GMC/CHEVROLET: ENGINES, WITH EGR SYSTEM, HAS LEAKAGE FROM EGR COOLER ENGINE COOLANT INTO THE COMBUSTION CHAMBER. MODEL 2002-15 SILVERADO, SIERRA, 2004-09 KODIAK C4500-C5500, TOPKICK C4500-C5500, 2006-15 EXPRESS, SAVANA. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. Read More »
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an engine noise, low oil pressure, over-speed condition, or abnormal oil sludge build up in the crankcase. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. Read More »
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This informational bulletin provides information for Identifying Non-GM ECM Calibration Use and Power-up Hardware Detection in Duramax Diesel Engines - Photograph Tech 2 Calibration IDs, Calibration Verification Numbers (CVNs) and ... Read More »
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Read More »
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2A? or global diagnostic system 2 ... Read More »
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a planetary gear whine noise in first and second gear. Technician should compare the noise to a like vehicle. Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow?. Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
DIAGNOSTIC INFORMATION ON MH1, MN8, MT1, M15 TRANSMISSION SLIPS, WILL NOT SHIFT OR MAY OVERHEAT, SES/MIL MAY BE ILLUMINATED, DTCS P0218, P0894 SET. *PE UPDATED 8/12/08. *PE Read More »
DIAGNOSTIC INFORMATION ON MN8, MT1 SES/MIL ILLUMINATED, DTC P0757, HARSH SHIFT, DELAYED 2-3 SHIFT, 2-3 SHIFT FLARE, NO THIRD GEAR, SLIPS IN THIRD GEAR OR REVERSE. *PE Read More »
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow?. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This technical bulletin provides a procedure to repair a possible wiring harness repair if damaged by the parking brake, brake booster mount or brake pedal bolt. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramax? diesel engines ? Photograph Tech 2? Calibration IDs, Calibration Verification Numbers ... Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection ... Read More »
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Read More »
This Preliminary Information communication provides information to the technician that some vehicles may have an Antilock Braking System/ Traction Control System Malfunction Indicator Lamp are on or other various electrical issues. Read More »
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Read More »
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). Read More »
GM: THE DOME LIGHT IS INOPERATIVE. THE AIR BAG LIGHT IS ON AND THE DOOR AJAR LIGHT IS ON. THIS IS LIKELY CAUSED BY A WIRING HARNESS. *RM UPDATED ON 6/27/2011. *KB Read More »
SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not Read More »
This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement. Read More »
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are ... Read More »
This technical bulletin provides a procedure to repair a possible wiring harness repair if damaged by the parking bark, brake booster mount or brake pedal bolt. Read More »
This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices causing multiple issues. Read More »
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS
ENGINE COMPARTMENT FUSE BLOCK COVER ON SOME 2003-2007 CHEVROLET EXPRESS AND GMC SAVANA VEHICLES MAY BREAK WHEN THE COVER IS REMOVED, ALLOWING WATER AND ROAD CONTAMINATES TO ENTER THE FUSE BLOCK. Read More »
LOSS OF IGNITION 1 VOLTAGE TO THE IGNITION COILS. CONSUMER EXPERIENCED INTERMITTENT STALL, MISFIRE, OR CRANK NO START. THERE MAY BE NO TROUBLE CODES SET. *KB UPDATED 3/17/09. *PE Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs) Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER:SENSOR/SENDING UNIT
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. Read More »
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This informational bulletin provides additional information on identifying duramax aftermarket power up devices that may cause damage to the engine and not covered under warranty. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491). Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not replace any glass for this reason. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions. Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This preliminary informational bulletin provides information to technicians that when replacing the passenger side airbag also install the I/P stow tray (trim piece). Read More »
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button ... Read More »
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. Read More »
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button ... Read More »
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational bulletin provides repair information to correct a customer concern that a crack has developed on the spring mount area of the front shock absorber mounting bracket. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead ... Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty. Read More »
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on. Read More »
USE OF NITROGEN GAS IN TIRES. *AK 2015 AND PRIOR GM PASSENGER CARS & TRUCKS (INCLUDING SATURN) ALSO 2008 AND PRIOR HUMMER H2, H3, SAAB 9-7X. UPDATED 5/12/08. Read More »
This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information. Read More »
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes. Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on. Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramaxa?? diesel engines a?? Photograph Tech 2A? Calibration IDs, Calibration Verification ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an engine noise, low oil pressure, over-speed condition, or abnormal oil sludge build up in the crankcase. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This technical bulletin provides a procedure to replace the rear leaf spring shackle to correct a condition of a noise from the rear leaf sprin under acceleration and high loads due to the rear leaf spring shackle coming into contact with ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
This informational bulletin provides technicians with Information for Identifying non-GM ECM calibration use and Power-Up hardware detection in Duramax? diesel engines ? Photograph Tech 2? Calibration IDs, Calibration Verification Numbers ... Read More »
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores. Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only). Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This informational bulletin provides additional information on identifying duramax aftermarket power up devices that may cause damage to the engine and not covered under warranty. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making. Read More »
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information. Read More »
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission. Read More »
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is ... Read More »
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Read More »
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Read More »
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only. Read More »
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only. Read More »
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service. Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only) Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only). Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS. Read More »
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs) Read More »
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Read More »
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. Read More »
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only) Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Bulletin has been Revised to add the 2017 Colorado, Cruze, Canyon, Chevrolet & GMC Light/Medium Duty Trucks. Please discard Corporate Bulletin Number 03-06-04-071I Read More »
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores Read More »
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not. Read More »
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only) Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, ... Read More »
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm. Read More »
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them. Read More »
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Read More »
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist ... Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only) Read More »
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only) Read More »
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks Read More »
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Read More »
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable. Read More »
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only). Read More »
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
GENERAL MOTORS:THE REAR A/C IS INOPERATIVE. MAY BE CAUSED BY THE A/C SUCTION LINE CONTACTING THE POSITIVE BATTERY CABLE. OVER TIME THE POSITIVE BATTERY CABLE INSULATION MAY RUB THROUGH. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
