Technical Service Bulletins (TSBs) for the 2017 Acadia are official communications between GMC & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates a technician may replace a steering gear and after programming it, find communication codes set and a loss of steering assist. Read More »
This Preliminary information communicates a technician may replace a steering gear and after programming it, find communication codes set and a loss of steering assist. Read More »
This Preliminary information communicates a technician may replace a steering gear and after programming it, find communication codes set and a loss of steering assist. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
This Preliminary information communicates that a vehicle may come to the dealer with a "Service Steering Message" and no codes set that pertain to the steering system. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This technical bulletin provides procedures for How to Determine if Wheel to Rotor Interface Click Noise is Present to correct conditions of Clicking Noise from Front of Vehicle with Wheels Straight Ahead on Acceleration Tip In/Tip Out or ... Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This Preliminary information communicates a possible power steering fluid leak above the engine harness to to the rear( Bank 1) heated Oxygen sensor and direction to replace all involved parts due to this contamination and leak. Read More »
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
This technical bulletin provides repair information to correct a customer concern of high efforts required to press steering wheel pad to sound horn. Read More »
Engineering Information ? Clicking/Scraping/Popping or Squeak/Creak Noise Coming from Front of Vehicle While Turning or at Slow Speeds Over Bumps Read More »
This Preliminary information communicates a possible power steering fluid leak above the engine harness to to the rear( Bank 1) heated Oxygen sensor and direction to replace all involved parts due to this contamination and leak. Read More »
This Preliminary Information communicates to thetechnician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - ... Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication advises the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
Vibration Felt Throughout Vehicle While in AWD Cruising at Highway Speeds Some customers may comment that a vibration is felt in the steering wheel, front or rear seats or cabin body boom while cruising at a steady state at highway ... Read More »
This technical bulletin provides a procedure to reprogram the power steering control module to correct a condition of Reduced Steering Assist Message with DTC C0460 Sym 5A due to a software abnormality. Read More »
Reduced Steering Assist Message with DTC C0460 Sym 5A Condition Some customers may comment on a Reduced Steering Assist message on the DIC with no loss of steering assist. During diagnosis a technician may find DTC C0460 Sym 5A. Read More »
This Preliminary information communicates a possible power steering fluid leak above the engine harness to to the rear( Bank 1) heated Oxygen sensor and direction to replace all involved parts due to this contamination and leak. Read More »
This technical bulletin provides a procedure to replace the P/S hose, O2 sensor and engine harness if P/S fluid has been found leaking and the cause of the Mil on. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT SOME CUSTOMERS MAY COMMENT ON THE OPERATION OF THEIR HAPTIC SEAT DURING A LANE KEEP ASSIST EVENT. LANE KEEP ASSIST WORKS DIFFERENTLY THAN LANE DEPARTURE WARNING. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates that a vehicle may be encountered with a clunk or rattle from the front of the vehicle. The dealer technician is instructed to remove the cradle brace and see if the noise is gone. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This technical bulletin provides procedures for How to Determine if Wheel to Rotor Interface Click Noise is Present to correct conditions of Clicking Noise from Front of Vehicle with Wheels Straight Ahead on Acceleration Tip In/Tip Out or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This informational bulletin advises the technician not to change the crankshaft balancer if it has the illusion of a wobble or vibration appearance. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE REAR SHOCK LOCATOR PINS FOR TECHNICIANS THAT NOTICE A BENT PIN DURING INSTALLATION OF NEW REAR SHOCK ABSORBERS. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a noise originating from the front of the vehicle during slow maneuvers or turns while hitting bumps. Read More »
Engineering Information ? Clicking/Scraping/Popping or Squeak/Creak Noise Coming from Front of Vehicle While Turning or at Slow Speeds Over Bumps Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This informational bulletin provides information to inspect the strut/spring assembly and front lower control arm bushing including the front lower control arm rear bushing for damage/wear causing a clunk type noise heard over bumps. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This informational bulletin provides information to inspect the strut/spring assembly and front lower control arm bushing including the front lower control arm rear bushing for damage/wear causing a clunk type noise heard over bumps. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE JOUNCE BUMPERS TO CORRECT A CUSTOMER CONCERN THAT A CLUNK NOISE CAN BE HEARD FROM THE REAR SUSPENSION ON MODERATE TO SEVERE JOUNCE IN COLD TEMPERATURES DUE TO THE REAR SUSPENSION ... Read More »
This technical bulletin provides repair information to correct a dealership technician concern of bent rear shock locator pin(s) noticed during rear shock absorber replacement. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This service bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Read More »
This technical bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This technical bulletin provides a procedure to apply grease to the shims on the front brake pads to correct a condition of Squeal Noise Originating from Front Brakes During Brake Apply. Read More »
This informational bulletin provides information on Replacement of the Park Brake Actuator Unit and/or the Electric Park Brake Wire, If during service, there is a need to replace the park brake actuator unit and/or the electric park brake ... Read More »
16128 - Service Update. The upper and lower brake lines may contact the fuel feed line at the rear left side of the fuel tank if the fuel tank has shifted during vehicle assembly. Read More »
16195-01 - Service Update (Service Procedure Revised). Certain vehicles may have a brake pedal position sensor (BPPS) flag bracket which allows too much rotation, causing the BPPS sensor to indicate the brake pedal is applied. Read More »
16195 - Service Update. Certain vehicles may have a brake pedal position sensor (BPPS) flag bracket which allows too much rotation, causing the BPPS sensor to indicate the brake pedal is applied. Read More »
This technical bulletin provides repair information to correct a customer concern of the Electric Park Brake (EPB) switch loose, falling into knee bolster. Read More »
This technical bulletin provides a procedure on replacing the pedal assembly to correct a condition of brake lights always on, cruise control inoperative and/or discharged battery due to the plastic Brake Pedal Position Sensor (BPPS) flag ... Read More »
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This technical bulletin provides a procedure to replace the front brake pads with single shim pad kit to correct a condition of Squeal Noise Originating from Front Brakes During Brake Apply. Read More »
This technical bulletin provides a procedure to apply grease to the shims on the front brake pads to correct a condition of Squeal Noise Originating from Front Brakes During Brake Apply. Read More »
This technical bulletin provides a procedure to apply grease to the shims on the front brake pads to correct a condition of Squeal Noise Originating from Front Brakes During Brake Apply. Read More »
This technical bulletin provides a procedure to apply grease to the shims on the front brake pads to correct a condition of Squeal Noise Originating from Front Brakes During Brake Apply. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Brake Pedal Low or Goes to Floor with No External Signs of a Leak. Read More »
This technical bulletin provides a procedure to apply grease to the shims on the front brake pads to correct a condition of Squeal Noise Originating from Front Brakes During Brake Apply. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DRUM:WHEEL CYLINDERS
This informational bulletin provides information on the proper ways to remove or replace the key cylinder covers due to some vehicles having the key cylinders hidden during the time of delivery. Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS
This technical bulletin provides a procedure to apply grease to the shims on the front brake pads to correct a condition of Squeal Noise Originating from Front Brakes During Brake Apply. Read More »
Squeal Noise Originating from Front Brakes During Brake Apply Condition - Some customers may comment on a squeal noise from the front brakes during brake apply Correction - Apply a coat of paste between the shims of the front brake ... Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR
This technical bulletin provides procedures for How to Determine if Wheel to Rotor Interface Click Noise is Present to correct conditions of Clicking Noise from Front of Vehicle with Wheels Straight Ahead on Acceleration Tip In/Tip Out or ... Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
Squeal Noise Originating from Front Brakes During Brake Apply Condition - Some customers may comment on a squeal noise from the front brakes during brake apply Correction - Apply a coat of paste between the shims of the front brake ... Read More »
This technical bulletin provides procedures for How to Determine if Wheel to Rotor Interface Click Noise is Present to correct conditions of Clicking Noise from Front of Vehicle with Wheels Straight Ahead on Acceleration Tip In/Tip Out or ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides diagnostic strategy information to aid in diagnosing a Ticking, Tap or Rattle Noise from Engine with Possible Misfire, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from ... Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary information communicates to technician's if they remove the front timing cover when performing a repair, they should inspect the timing chain guide upper bolt for being loose. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This technical bulletin provides repair information to correct a customer concern of potential reduced engine power message displayed and/or engine stall with DTCs P1682 and/or P0689 Set. Read More »
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct ... Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This technical bulletin provides a procedure to replace the P/S hose, O2 sensor and engine harness if P/S fluid has been found leaking and the cause of the Mil on. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. Read More »
This technical bulletin provides a procedure to test the fuel level sensors to validate if the cause of the customers concerns and to replace the pump if validated the pump has failed. Read More »
This Preliminary information communicates to the technician where to find the engine identification tag and what information on that tag to use during programming of someengine control modules. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Vehicle No Start, Stalls Repeatedly and/or Smoke from Under Hood at Battery. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a knocking noise from the engine under light load while driving with engine speed between 1100 and 1800 rpm. Read More »
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of No Crank and/or Start After Being Parked for Extended Time with Less Than 1,500 Miles (2,414 Km). Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated with DTC P0171 and/or P0174. Read More »
Certain 2017 model year Buick LaCrosse or GMC Acadia vehicles, that have had an engine replacement may have the wrong torque applied to front cradle-to-body bolts (M14) and front cradle stabilizer brackets-to-body bolts (M10). Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin advises the technician not to change the crankshaft balancer if it has the illusion of a wobble or vibration appearance. Read More »
This Preliminary information communicates a possible power steering fluid leak above the engine harness to to the rear( Bank 1) heated Oxygen sensor and direction to replace all involved parts due to this contamination and leak. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces. Read More »
This engineering informational bulletin is ending the need for information from the field on vehicles that have the condition of Oil Leak Between Upper and Lower Oil Pan. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated with DTC P0171 and/or P0174. Read More »
This informational bulletin advises the technician not to change the crankshaft balancer if it has the illusion of a wobble or vibration appearance. Read More »
This technical bulletin provides a procedure to locate and repair the engine wiring harness if found chaffing against the water outlet bolt boss. Read More »
This engineering informational bulletin is requesting information from the field of vehicles with the condition of a SES light on with one or more DTC's set. Read More »
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. Read More »
16088 - Service Update. Certain vehicles, may have a condition in which oil is starved to the overhead left side intake camshaft journals and the two #2 cylinder intake valve stationary hydraulic lash adjuster due to the hole not punched ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic. Read More »
This engineering information bulletin is requesting information from the field on vehicles that have the condition of Engineering Information a?? Repeat Malfunction Indicator Lamp (MIL) on with DTC P0300 (Engine Misfire ... Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. Read More »
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE E80 ENGINE CONTROL MODULE PART NUMBERS 12669908 OR 12672502 HAVE BEEN PLACED ON PART RESTRICTION BY GENERAL MOTORS TECHNICAL ASSISTANCE. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminateda??. Read More »
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information for dealers/technicians on Rough Idle, Malfunction Indicator Lamp (MIL) Illuminated After Engine Repairs with DTCs P0016 and/or P0018 Set. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from ... Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates that a vehicle may be encountered with a clunk or rattle from the front of the vehicle. The dealer technician is instructed to remove the cradle brace and see if the noise is gone. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This service bulletin advises the technician of a diagnostic test for a possible issue with a damaged OCV solenoid that may cause an oil leak and misfire, illuminating the MIL and setting DTCs P0300, P0302 and/or P0305. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This engineering informational bulletin is requesting to gather information from the field to determine a root cause for a condition of oil leaking from the valve rocker arm oil control valve. Read More »
N192210240 - Special Coverage Adjustment - Certain vehicles shown above, may have a condition that could cause the evaporative emissions purge valve to not fully close. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of No Crank and/or Start After Being Parked for Extended Time with Less Than 1,500 Miles (2,414 Km). Read More »
This informational bulletin provides information of a possible misfire that may happen from incorrect camshafts being installed in the reman engines. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Oil Leak Between Upper and Lower Oil Pan. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This engineering information bulletin ends the need for information from the field on vehicles that have the concern of a noisy water pump. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This technical bulletin provides a procedure to replace the P/S hose, O2 sensor and engine harness if P/S fluid has been found leaking and the cause of the Mil on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have rusty or corroded appearance on the exhaust components. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. Read More »
This technical bulletin provides a procedure to Replace the PCV valve tube assembly to correct a condition of the engine make a whistle noise at idle and during engine shut down due to a restriction in the positive crankcase ventilation ... Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This technical bulletin provides a procedure to replace the P/S hose, O2 sensor and engine harness if P/S fluid has been found leaking and the cause of the Mil on. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated with DTC P0171 and/or P0174. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This technical bulletin provides a procedure to test the fuel level sensors to validate if the cause of the customers concerns and to replace the pump if validated the pump has failed. Read More »
This technical bulletin provides a procedure to test the fuel level sensors to validate if the cause of the customers concerns and to replace the pump if validated the pump has failed. Read More »
This technical bulletin provides a procedure to test the fuel level sensors to validate if the cause of the customers concerns and to replace the pump if validated the pump has failed. Read More »
This technical bulletin provides a procedure to test the fuel level sensors to validate if the cause of the customers concerns and to replace the pump if validated the pump has failed. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various noises within the engine as well as some misfire causes. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information ? Malfunction Indicator Lamp (MIL) On DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 ... Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information ? Malfunction Indicator Lamp (MIL) On DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 ... Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information ? Malfunction Indicator Lamp (MIL) On DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 ... Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Check Engine Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0641. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Check Engine Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0641. Read More »
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Engineering Information ? Malfunction Indicator Lamp (MIL) On, DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 Fuel Trim System Lean Bank 2 Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
17086 - Service Update - Certain vehicles may have been built with an unnecessary gasket in the high pressure fuel pump assembly. The fuel pump may wear out early, and this could lead to degradation of engine performance over time. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch shudder, 2-3 Upshift or 3-2 Downshift concerns. Read More »
This technical bulletin provides repair information to correct a customer concern of potential reduced engine power message displayed and/or engine stall with DTCs P1682 and/or P0689 Set. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct the customer concern of launch shudder. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This Preliminary information communicates a possible power steering fluid leak above the engine harness to to the rear( Bank 1) heated Oxygen sensor and direction to replace all involved parts due to this contamination and leak. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
17389 - Service Update. Some vehicles were shipped with a power transfer unit (PTU) that failed leak testing. Dealers are to replace the PTU. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This informational bulletin advises the technician not to change the crankshaft balancer if it has the illusion of a wobble or vibration appearance. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have harsh 1-2 shift, mostly on light throttle with no Diagnostic Trouble Codes present. Read More »
This Preliminary Information communication advises the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty ... Read More »
THIS TECHNICAL BULLETIN PROVIDES THE PROCEDURES TO COMPLETE A TRANSSMISSION ADAPTIVE LEARN ON ALL THE DIFFERENT TYPES OF VEHICLES AND TRANSMISSIONS BASED ON RPO OPTIONS TO CORRECT A CONDITION OF HARSH SHIFTS ON HARD ACCELLERATIONS. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch shudder, 2-3 Upshift or 3-2 Downshift concerns. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
17109-Service Update. Certain vehicles, equipped with all-wheel drive (RPO F48), may have a condition in which the rear differential carrier assembly could apply higher than commanded torque at high mileage. Read More »
Vibration Felt Throughout Vehicle While in AWD Cruising at Highway Speeds Some customers may comment that a vibration is felt in the steering wheel, front or rear seats or cabin body boom while cruising at a steady state at highway ... Read More »
This technical bulletin provides repair information to correct customer concerns of multiple electrical issues, dead battery, start/stop inoperative, instrument cluster and switch backlighting remain illuminated. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This service bulletin provides information for dealers/technicians on Rough Idle, Malfunction Indicator Lamp (MIL) Illuminated After Engine Repairs with DTCs P0016 and/or P0018 Set. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides repair information to correct a customer concern of Intermittent Door Locks Inoperative, DTCs B3125, B3130, B3135, B3979, B3980, Various U codes, IP Lamps Illuminate, Immobilizer, Unwanted Horn or Hazard ... Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This service bulletin advises the technician of a diagnostic test for a possible issue with a damaged OCV solenoid that may cause an oil leak and misfire, illuminating the MIL and setting DTCs P0300, P0302 and/or P0305. Read More »
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This service bulletin provides diagnostic strategy information to aid in diagnosing a Ticking, Tap or Rattle Noise from Engine with Possible Misfire, Malfunction Indicator Lamp (MIL) Illuminated. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service AWD Lamp illuminated on the Driver Information Center (DIC) ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service AWD Lamp illuminated on the Driver Information Center (DIC) ... Read More »
This service bulletin provides a service procedure to correct a customer concern of Power Liftgate Stops When Opening and/or Will Not Close from Open Position DTC B153F Sets. Read More »
This service bulletin provides information to determine the root cause of the water intrusion to the Video Processing Module (VPM) and correct it prior to replacement of the VPM. Read More »
This Preliminary Information communication provides information to the technician about vehicle that have the Driver Information Center button inoperative. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides information to determine the root cause of the water intrusion to the Video Processing Module (VPM) and correct it prior to replacement of the VPM. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This technical bulletin provides a procedure for replacing the body plugs due to water leaking through the body plug above the connector X500 causing the connector to be corroded. Read More »
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic. Read More »
This informational bulletin provides information on Normal Radio Display Operation ? Display Does Not Remain Off at Times After Being Turned Off in Settings and no parts should be replaced due to this condition. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This technical bulletin provides a procedure for replacing the body plugs due to water leaking through the body plug above the connector X500 causing the connector to be corroded. Read More »
This engineering Information (EI) ends the need for information from the field for a condition of oil leaking from the valve rocker arm oil control valve. If a vehicle is encountered with this condition, refer to SI for further diagnosis. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct ... Read More »
This technical bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates additional diagnostics and repair to assist in resolving a malfunction indicator lamp illumination due to any combination of diagnostic trouble codes P0068 P0101 P0106 P0171 P0131 P0137 P0324 ... Read More »
This technical bulletin provides repair information to correct a customer concern of an intermittent blank or flickering driver information center (DIC). Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct ... Read More »
N192218430 - Customer Satisfaction Program. During service, certain vehicles equipped with OnStar (RPO UE1), may have received an incorrect and partially programmed/configured replacement OnStar module. Read More »
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct ... Read More »
This technical bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This informational bulletin provides Information on Using Voice Pass-Thru to Access Voice Recognition Commands on Cell Phone and how it does not work on models equipped with IOA and IOB radios. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This technical bulletin provides repair information to correct customer concerns of multiple electrical issues, dead battery, start/stop inoperative, instrument cluster and switch backlighting remain illuminated. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This technical bulletin provides repair information to correct a customer concern of an intermittent blank or flickering driver information center (DIC). Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This technical bulletin provides a procedure to replace the P/S hose, O2 sensor and engine harness if P/S fluid has been found leaking and the cause of the Mil on. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
N172097060 - Special Coverage Adjustment. Certain vehicles may have a condition where the Side Blind Zone Alert (SBZA) modules may fail or malfunction due to water intrusion. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This technical bulletin provides repair information to correct a customer concern of an intermittent blank or flickering driver information center (DIC). Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This technical bulletin provides a procedure to test the fuel level sensors to validate if the cause of the customers concerns and to replace the pump if validated the pump has failed. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar? Module Functionality After OnStar Module Replacement for Another Condition. Read More »
This technical bulletin provides repair information to correct customer concerns of multiple electrical issues, dead battery, start/stop inoperative, instrument cluster and switch backlighting remain illuminated. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module. Read More »
This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle. Read More »
This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary information communicates additional diagnosticsand repairto assist in resolving a malfunction indicator lampillumination due to any combination of diagnostic trouble codes P0068 P0101 P0106 P0171 P0131 P0137 P0324 P0326 ... Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communicates to thetechnician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
Intermittent Operation of Key Fobs, Door Unlock Inoperative ?No Remote Detected? Message with Possible TPM MIL Some customers may comment on intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information ? Malfunction Indicator Lamp (MIL) On DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin provides information for programming the low speed LAN module due to the mirrors memory position reverse tilt position is inoperative. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Read More »
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Read More »
This Preliminary Information communicates to thetechnician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when watching a movie the audio does not match the video when playing though the vehicles speakers. Read More »
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system. Read More »
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. Read More »
This Preliminary Information communicationends thewireless charging module restriction through the General Motors Technical Assistance Center. Read More »
16195-01 - Service Update (Service Procedure Revised). Certain vehicles may have a brake pedal position sensor (BPPS) flag bracket which allows too much rotation, causing the BPPS sensor to indicate the brake pedal is applied. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have harsh 1-2 shift, mostly on light throttle with no Diagnostic Trouble Codes present. Read More »
This technical bulletin provides a procedure to install a new ANC module and a shield to deflect any water away from the module if found shorting the module out. Read More »
This technical bulletin provides repair information to correct a customer concern of the Electric Park Brake (EPB) switch loose, falling into knee bolster. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface ... Read More »
53170 Service Update. On certain vehicles the battery B+ cable may chafe from contact with the battery negative (engine block ground) cable. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Read More »
This technical bulletin provides a procedure on replacing the pedal assembly to correct a condition of brake lights always on, cruise control inoperative and/or discharged battery due to the plastic Brake Pedal Position Sensor (BPPS) flag ... Read More »
This Preliminary Information communication advises the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This informational bulletin explains how the technician no longer needs to perform the 3 hour battery relearn procedure on 2017 vehicles with Start/Stop. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This technical bulletin provides a procedure to reprogram the ECM to the latest calibrations to correct the customers concern of the the MIL on with code P05CE set. Read More »
This technical bulletin provides a procedure to reprogram the ECM to the latest calibrations to correct the customers concern of the the MIL on with code P05CE set. Read More »
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Read More »
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module. Read More »
This technical bulletin provides a procedure to remove the F30DA Fuse and use a small pick to fix the fuse and reinstall the fuse to correct a condition of the steering wheel controls being inoperative. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE ONSTAR WIRELESS FIDELITY INOPERATIVE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATES THAT WHEN CUSTOMER OR TECHNICIAN MAY INDICATE WHEN ATTEMPTING TO ADD A NEW TRANSMITTER TO A VEHICLE FOLLOWING THE ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM PROCEDURE. Read More »
66110 - Service Update - The driver mode control switch does not allow the driver to alter chassis and powertrain attributes. Mode selection is not lit on the switch. Dealers will reprogram the engine control module. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABUT VEHICLES THAT MAY HAVE MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND P05CE SET. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATES THE STEPS TO DIAGNOSE THE CONCERN OF P0264 OR P0265 ALONG WITH P0300 ON THESE PARTICULAR VEHICLES, IT ALSO EXPLAINS THE INSPECTION AND REPAIR STEPS TO ENSURE THE CORRECT REPAIR ON THESE VEHICLES ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA. Read More »
50210 - Service Update. These vehicles may have a condition where the EBCM does not notify the driver through an ABS or Electronic Stability Control (ESC) telltale or set the appropriate diagnostic trouble codes (DTC) if an open flyback ... Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE IDENTIFICATION OF VEHICLES THAT ARE SHIPPED WITH THE TRANSPORT MODE ON AND HOW TO TURN IT OFF. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Vehicle No Start, Stalls Repeatedly and/or Smoke from Under Hood at Battery. Read More »
This technical bulletin provides repair information to correct customer concerns of multiple electrical issues, dead battery, start/stop inoperative, instrument cluster and switch backlighting remain illuminated. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This informational bulletin explains how the technician no longer needs to perform the 3 hour battery relearn procedure on 2017-2018 vehicles with Start/Stop. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Read More »
This preliminary informational bulletin provides information regarding the need to relearn the auto/start and stop feature on vehicles equipped after a repair has been completed on the vehicle. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This Preliminary Information communication provides information to the technician about vehicle that have the Driver Information Center button inoperative. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary information communicates additional diagnosticsand repairto assist in resolving a malfunction indicator lampillumination due to any combination of diagnostic trouble codes P0068 P0101 P0106 P0171 P0131 P0137 P0324 P0326 ... Read More »
This technical bulletin provides repair information to correct customer concerns of multiple electrical issues, dead battery, start/stop inoperative, instrument cluster and switch backlighting remain illuminated. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. Read More »
All or Some Options May Be Missing from Driver Information Center (DIC) ?Info Pages? Menu Due to Them Not Being Selected Condition Some customers may comment that with the ?Info? option selected from the main menu (1), the ?Info ... Read More »
This technical bulletin provides a procedure on how to take the vehicles out of transport mode for vehicles with the condition of Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is ... Read More »
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Read More »
This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Read More »
This technical bulletin provides a procedure to reprogram the radio to correct a condition of Apple Carplay Will Not Launch After 1124 Key Cycles and Displays Message Advising to Connect a Supported Device via USB Even Though One is ... Read More »
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information ? Malfunction Indicator Lamp (MIL) On DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 ... Read More »
This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle. Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a Service Driver Assist System Message with B172E stored in history Do not replace any parts. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use. Read More »
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed. Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for E82 engine control module Restriction Part Number 12659078. Read More »
This Preliminary information communicates the frontview camera will not calibrate / learn. Update GDS 2 to the latest Diagnostic package 2017.3.1 release 04/03/17. Then go back and do the learn. Read More »
17056 - Service Update. Certain vehicles may have a condition in which condensation from the HVAC module can leak into the housing of the active noise cancellation (ANC) module. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin explains DTC U0121 sets due to a software anomaly and does not turn the MIL on or change performance of the vehicle. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communicationends thewireless charging module restriction through the General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This informational bulletin explains DTC U0121 sets due to a software anomaly and does not turn the MIL on or change performance of the vehicle. Read More »
This Preliminary Information communication advises the technician that the E80 Engine Control Module part numbers 12669908 or 12672502 have been placed on part restriction by General Motors Technical Assistance Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE ONSTAR WIRELESS FIDELITY INOPERATIVE. Read More »
This technical bulletin provides a procedure to reprogram the Radar Sensor module-long range so that the sensors can see shadows and correct the customers concern of the brakes applying in parking structures and close parking enviroments. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABUT VEHICLES THAT MAY HAVE MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND P05CE SET. Read More »
57100 - Service Update Bulletin. Some vehicles equipped with a one color Driver Information Center (DIC) (RPO UDC) were built with software that is not compatible with the Radio and DIC Steering Wheel Controls, causing the controls to be ... Read More »
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2. Read More »
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ... Read More »
This technical bulletin provides repair information to correct customer concerns of multiple electrical issues, dead battery, start/stop inoperative, instrument cluster and switch backlighting remain illuminated. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides repair information to correct a customer concern of Intermittent Door Locks Inoperative, DTCs B3125, B3130, B3135, B3979, B3980, Various U codes, IP Lamps Illuminate, Immobilizer, Unwanted Horn or Hazard ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON EXTERIOR LIGHTING COMPONENTS THAT HAVE BEEN TINTED OR SMOKED BY AN OUTSIDE VENDOR AND GENERAL MOTORS POSITION ON ALTERING THESE COMPONENTS. Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates that a customer may come to the dealer with a complaint of a hum, drone or pulsing type noise at times. Read More »
This Preliminary information communicates that a customer may come to the dealer with a complaint of a hum, drone or pulsing type noise at times. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
N172097060 - Special Coverage Adjustment. Certain vehicles may have a condition where the Side Blind Zone Alert (SBZA) modules may fail or malfunction due to water intrusion. Read More »
This informational bulletin provides information for assisting the customer in setting the position for the memory mirror and the reverse tilt Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN ADDS 2015 - 2017 MY'S TO REPAIR INFORMATION FOR A CUSTOMER CONCERN THAT FRONT SUNROOF SUNSHADE WILL NOT LATCH IN THE CLOSED POSITION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary information communicates information to let dealers know that the sunshade catch is available and not to replace sunroof housing. Read More »
This Preliminary information communicates information to let dealers know that the sunshade catch is available and not to replace sunroof housing. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This technical bulletin provides repair information to correct a customer concern of the sunshade auto open feature noisy or inoperative, and/or sunshade latch handle broken. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
16158 Customer Satisfaction. Certain vehicles may have a condition in which the rearview image will show a reversed image when in reverse. Dealers will inspect and, if necessary, replace the rearview camera. Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This informational bulletin provides information on the inboard seat airbag is mounted in this area and creates a slightly different contour of the seat causing an appearance concern, and that this should be considered normal and no parts ... Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON LOCATING AND RECONNECTING AIRBAG CONNECTORS THAT ARE NOT FULLY SEATED TO CORRECT A CUSTOMER CONCERN OF AN AIRBAG WARNING LAMP ILLUMINATED, OR ONE, OR MORE, AIRBAG DTC(S) SET. Read More »
Customer Satisfaction Program - On certain vehicles, equipped with the second row bench seats (RPO ABC or ABA) may have a condition in which the second row middle seat belt buckle can fall down between the second row bench seats and be ... Read More »
Customer Satisfaction Program - On certain vehicles, equipped with the second row bench seats (RPO ABC or ABA) may have a condition in which the second row middle seat belt buckle can fall down between the second row bench seats and be ... Read More »
This technical bulletin provides a procedure for the driver seat belt buckle due to the seat belt buckle switch wiring pigtail getting pinched between the buckle and the buckle mounting bracket. Read More »
This technical bulletin provides repair information to correct a customer concern of hearing a rattle noise from the 2nd row outboard seat belt retractor latch plate. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES WITH SECOND AND/OR THIRD ROW BENCH SEAT CENTER SEAT BELT BUCKLES HAVE A CRACK IN THE PLASTIC COVER ON THE BUCKLE SIDE. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This service bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch shudder, 2-3 Upshift or 3-2 Downshift concerns. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides information to determine the root cause of the water intrusion to the Video Processing Module (VPM) and correct it prior to replacement of the VPM. Read More »
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch shudder, 2-3 Upshift or 3-2 Downshift concerns. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing or feeling a sharp edge on the upper inboard corner of the rear body structure stop lamp. Read More »
This Preliminary information communicates that a vehicle may be encountered with a "service park assist system" message or a rear lift gate that will not open passively. Read More »
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct the customer concern of launch shudder. Read More »
This technical bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing or feeling a sharp edge on the upper inboard corner of the rear body structure stop lamp. Read More »
N172097060 - Special Coverage Adjustment. Certain vehicles may have a condition where the Side Blind Zone Alert (SBZA) modules may fail or malfunction due to water intrusion. Read More »
17409 - Customer Satisfaction. Certain vehicles, that have had an engine replacement may have the wrong torque applied to front cradle-to-body bolts (M14) and front cradle stabilizer brackets-to-body bolts (M10). Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON THE PROPER WASHING OF THE BRIGHT ALUMINUM MOLDINGS TO AVOID THE MOLDINGS FROM GETTING DAMAGED. Read More »
17217 -Service Update. Some vehicles may experience a water leak from the passenger side A-Pillar area due to incomplete sealing within the plenum. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS. Read More »
This service bulletin provides information to determine the root cause of the water intrusion to the Video Processing Module (VPM) and correct it prior to replacement of the VPM. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
17217 -Service Update. Some vehicles may experience a water leak from the passenger side A-Pillar area due to incomplete sealing within the plenum. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This informational bulletin provides information for technicians that upon removal of a front door trim panel, two high retention retainers will break but must be replaced with same high retention retainers to properly secure the door trim. Read More »
This informational bulletin provides information for technicians that upon removal of a front door trim panel, two high retention retainers will break but must be replaced with same high retention retainers to properly secure the door trim. Read More »
This service bulletin provides a service procedure to correct a customer concern of Power Liftgate Stops When Opening and/or Will Not Close from Open Position DTC B153F Sets. Read More »
This technical bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Rattle Originating from Liftgate Trim Area. Read More »
This Preliminary Information communication advises the technician to replace the right hand lift-gate strut on 2007-2016 GMC Acadia and 2007-2010 Saturn Outlook if a clunk or pop is heard. Read More »
This service bulletin provides a service procedure to correct a customer concern of Power Liftgate Stops When Opening and/or Will Not Close from Open Position DTC B153F Sets. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information on tires are not meeting tread depth expectations, or wearing out (reaching 2/32)) too quickly. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects ... Read More »
This informational bulletin provides information to help the customers that are not familiar with specialty tires like summer, competition, run-flat and self-sealing. Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This warranty administration bulletin provide policy information on tires are not meeting tread depth expectations, or wearing out (reaching 2/32)) too quickly. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This warranty administration bulletin provide policy information on tires are not meeting tread depth expectations, or wearing out (reaching 2/32)) too quickly. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides information that the TPM sensors must always be relearned when accessory wheels are installed on the vehicle. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL ... Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This warranty administration bulletin provide policy information on tires are not meeting tread depth expectations, or wearing out (reaching 2/32)) too quickly. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This technical bulletin provides procedures for How to Determine if Wheel to Rotor Interface Click Noise is Present to correct conditions of Clicking Noise from Front of Vehicle with Wheels Straight Ahead on Acceleration Tip In/Tip Out or ... Read More »
This technical bulletin provides procedures for How to Determine if Wheel to Rotor Interface Click Noise is Present to correct conditions of Clicking Noise from Front of Vehicle with Wheels Straight Ahead on Acceleration Tip In/Tip Out or ... Read More »
Clicking Noise from Front Wheels While Turning at Slow Speeds Condition Some customers may comment on a clicking noise emanating from the front wheels location. Read More »
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided. Read More »
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels. Read More »
This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing each scenario and documenting findings. Read More »
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - ... Read More »
This preliminary bulletin provides a procedure to clean the back side of the rims and rotors and to correct the customers concern of wheel clicking. Read More »
This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Read More »
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes. Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
17409 - Customer Satisfaction. Certain vehicles, that have had an engine replacement may have the wrong torque applied to front cradle-to-body bolts (M14) and front cradle stabilizer brackets-to-body bolts (M10). Read More »
THIS INFORMATIONAL BULLETIN IS TO INFORM DEALERS OF SPECIAL PROCEDURES NECESSARY WHEN TOWING A TRAILER OR WHEN TOWING THE VEHICLE BEHIND A RECREATIONAL VEHICLE. Read More »
This service bulletin provides repair information to correct a customer concern of a squeak, rattle or creak coming from the second row/rear seat area. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak, rattle or creak coming from the second row/rear seat area. Read More »
Customer Satisfaction Program - On certain vehicles, equipped with the second row bench seats (RPO ABC or ABA) may have a condition in which the second row middle seat belt buckle can fall down between the second row bench seats and be ... Read More »
Customer Satisfaction Program - On certain vehicles, equipped with the second row bench seats (RPO ABC or ABA) may have a condition in which the second row middle seat belt buckle can fall down between the second row bench seats and be ... Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak, rattle or creak coming from the second row/rear seat area. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak, rattle or creak coming from the second row/rear seat area. Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak, rattle or creak coming from the second row/rear seat area. Read More »
This engineering information (EI) closure ends the need for information from the field for a condition of drivers seat track will not adjust forward and/or backwards and becomes seized. Read More »
This engineering informational bulletin is requesting information from the field to determine a root cause for a condition of drivers seat track will not adjust forward and/or backwards and becomes seized. Read More »
This Preliminary information communicates an Intermittent No Crank, No Start, or Reduced Power loss of data multiple U codes or Intermittent Power Door Locks inoperative, unwanted seat or mirror movement. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This technical bulletin provides a procedure to disengage the jammed parts and release the gears for proper function caused by the mechanical of the height adjustment being jammed, not broken creating a condition of difficult to adjust ... Read More »
This technical bulletin provides repair information to correct a customer concern of a squeak, rattle or creak coming from the second row/rear seat area. Read More »
This informational bulletin provides information on the inboard seat airbag is mounted in this area and creates a slightly different contour of the seat causing an appearance concern, and that this should be considered normal and no parts ... Read More »
16135 Service Update. Certain vehicles may have a condition in which the rear cargo area left hand 2nd row seat release handle doesn't release the seat, or requires too much effort to release. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE AND FORM TO SUBMIT TO GET THE CORRECT WIRE HARNESS FOR INSTALLING REAR HEADREST MONITORS ON VEHICLES DUE TO THE ACCESSORY KIT NOT COMING WITH THE CORRECT HANRESS NEEDED TO INSTALL. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT SOME CUSTOMERS MAY COMMENT ON THE OPERATION OF THEIR HAPTIC SEAT DURING A LANE KEEP ASSIST EVENT. LANE KEEP ASSIST WORKS DIFFERENTLY THAN LANE DEPARTURE WARNING. Read More »
This technical bulletin provides a procedure to disengage the jammed parts and release the gears for proper function caused by the mechanical of the height adjustment being jammed, not broken creating a condition of difficult to adjust ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO ADJUST THE REAR CARGO LEFT HAND SECOND ROW SEATS TO CORRECT A CONDITION OF THE REAR CARGO AREA LEFT HAND SECOND ROW SEAT DIFFICULT OR WILL NOT RELEASE. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Read More »
50210 - Service Update (revised population - message only). These vehicles may have a condition where the EBCM does not notify the driver through an ABS or Electronic Stability Control (ESC) telltale or set the appropriate diagnostic ... Read More »
50210 - Service Update. These vehicles may have a condition where the EBCM does not notify the driver through an ABS or Electronic Stability Control (ESC) telltale or set the appropriate diagnostic trouble codes (DTC) if an open flyback ... Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert". Read More »
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert". Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct ... Read More »
Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out Condition Some customers may comment on one or more of the following conditions: ? Forward Collision Alert ... Read More »
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert". Read More »
FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA
This Technical bulletin Reprograms the Radar Sensor Module-Long Range to correct a Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out condition. Read More »
Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out Condition Some customers may comment on one or more of the following conditions: ? Forward Collision Alert ... Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This technical bulletin provides a procedure to replace the Front Seat Lane Departure Warning Actuator if the B172E is set in the seat control module. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Preliminary Information communicates to thetechnician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication advises the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Preliminary Information communicates to thetechnician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Read More »
This Technical bulletin Reprograms the Radar Sensor Module-Long Range to correct a Forward Collision Alert Inoperative, Unwanted Application of Emergency Brakes and/or Adaptive Cruise Control Drops Out condition. Read More »
This Preliminary information communicates that a vehicle may be encountered with a clunk or rattle from the front of the vehicle. The dealer technician is instructed to remove the cradle brace and see if the noise is gone. Read More »
This Preliminary information communicates that a vehicle may be encountered with a clunk or rattle from the front of the vehicle. The dealer technician is instructed to remove the cradle brace and see if the noise is gone. Read More »
This Preliminary information communicates that a vehicle may be encountered with a clunk or rattle from the front of the vehicle. The dealer technician is instructed to remove the cradle brace and see if the noise is gone. Read More »
This Preliminary Information communicates to the technician that some customers may comment on the operation of their haptic seat during a Lane Keep Assist event. Lane Keep Assist works differently than Lane Departure Warning. Read More »
This Preliminary information communicates noise condition that has been identified and the repair that is in process. A special Labor Operation was added for tracking purposes only. Read More »
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. Read More »
This Preliminary information communicates a possible power steering fluid leak above the engine harness to to the rear( Bank 1) heated Oxygen sensor and direction to replace all involved parts due to this contamination and leak. Read More »
16158 Customer Satisfaction. Certain vehicles may have a condition in which the rearview image will show a reversed image when in reverse. Dealers will inspect and, if necessary, replace the rearview camera. Read More »
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. Read More »
This Preliminary Information communication provides information to the technician about vehicles with an intermittent loss of gridlines in the rear camera display screen and a "Service Rear Vision System" message that both happen at the ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES WITH AN INTERMITTENT LOSS OF GRIDLINES IN THE REAR CAMERA DISPLAY SCREEN AND A "SERVICE REAR VISION SYSTEM" MESSAGE THAT BOTH HAPPEN AT THE ... Read More »
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides repair information to correct a customer concern of Intermittent Door Locks Inoperative, DTCs B3125, B3130, B3135, B3979, B3980, Various U codes, IP Lamps Illuminate, Immobilizer, Unwanted Horn or Hazard ... Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin advises the technician of a diagnostic test for a possible issue with a damaged OCV solenoid that may cause an oil leak and misfire, illuminating the MIL and setting DTCs P0300, P0302 and/or P0305. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition. Read More »
This Preliminary information communicates to technician's if they remove the front timing cover when performing a repair, they should inspect the timing chain guide upper bolt for being loose. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service AWD Lamp illuminated on the Driver Information Center (DIC) ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service AWD Lamp illuminated on the Driver Information Center (DIC) ... Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This service bulletin provides information to determine the root cause of the water intrusion to the Video Processing Module (VPM) and correct it prior to replacement of the VPM. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that have the Driver Information Center button inoperative. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This technical bulletin provides a procedure for replacing the body plugs due to water leaking through the body plug above the connector X500 causing the connector to be corroded. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This technical bulletin provides a procedure for replacing the body plugs due to water leaking through the body plug above the connector X500 causing the connector to be corroded. Read More »
This technical bulletin provides repair information to correct a customer concern of the Service Engine Soon Lamp illuminated and/or Service Power Brake Assist message displayed, with DTCs P0557 or P0558 Stored. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This technical bulletin provides repair information to correct a customer concern of a water leak into interior, and/or various electrical concerns, liftgate actuator noisy or inoperative. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary information communicates to the technician information on what may be setting DTC P06DE. This is in addition to what is already in the service manual. Read More »
This Preliminary information communicates to the technician information on what may be setting DTC P06DE. This is in addition to what is already in the service manual. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC. Read More »
N192218430 - Customer Satisfaction Program. During service, certain vehicles equipped with OnStar (RPO UE1), may have received an incorrect and partially programmed/configured replacement OnStar module. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Read More »
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
Certain 2017 model year Buick LaCrosse or GMC Acadia vehicles, that have had an engine replacement may have the wrong torque applied to front cradle-to-body bolts (M14) and front cradle stabilizer brackets-to-body bolts (M10). Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
Intermittent Operation of Key Fobs, Door Unlock Inoperative ?No Remote Detected? Message with Possible TPM MIL Some customers may comment on intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Read More »
Vibration Felt Throughout Vehicle While in AWD Cruising at Highway Speeds Some customers may comment that a vibration is felt in the steering wheel, front or rear seats or cabin body boom while cruising at a steady state at highway ... Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
Engineering Information ? Malfunction Indicator Lamp (MIL) On, DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 Fuel Trim System Lean Bank 2 Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This engineering information bulletin is requesting information on vehicles that have the condition of A/C Inoperative and/or Compressor Seizure. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This informational bulletin advises the technician not to change the crankshaft balancer if it has the illusion of a wobble or vibration appearance. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
16135 01 - Service Update. Certain vehicles may have a condition in which the rear cargo area left hand 2nd row seat release handle doesn't release the seat, or requires too much effort to release. Read More »
This technical bulletin provides a procedure on replacing the pedal assembly to correct a condition of brake lights always on, cruise control inoperative and/or discharged battery due to the plastic Brake Pedal Position Sensor (BPPS) flag ... Read More »
This informational bulletin explains how the technician no longer needs to perform the 3 hour battery relearn procedure on 2017 vehicles with Start/Stop. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure to reprogram the ECM to the latest calibrations to correct the customers concern of the the MIL on with code P05CE set. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON THE TIRES SUPPLIED WITH A NEW VEHICLE ARE COVERED BY GENERAL MOTORS AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP UNDER THE BUMPER-TO-BUMPER NEW VEHICLE LIMITED WARRANTY. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL ... Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN ADDS 2015 - 2017 MY'S TO REPAIR INFORMATION FOR A CUSTOMER CONCERN THAT FRONT SUNROOF SUNSHADE WILL NOT LATCH IN THE CLOSED POSITION. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE AND FORM TO SUBMIT TO GET THE CORRECT WIRE HARNESS FOR INSTALLING REAR HEADREST MONITORS ON VEHICLES DUE TO THE ACCESSORY KIT NOT COMING WITH THE CORRECT HANRESS NEEDED TO INSTALL. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO ADJUST THE REAR CARGO LEFT HAND SECOND ROW SEATS TO CORRECT A CONDITION OF THE REAR CARGO AREA LEFT HAND SECOND ROW SEAT DIFFICULT OR WILL NOT RELEASE. Read More »
THIS INFORMATIONAL BULLETIN IS TO INFORM DEALERS OF SPECIAL PROCEDURES NECESSARY WHEN TOWING A TRAILER OR WHEN TOWING THE VEHICLE BEHIND A RECREATIONAL VEHICLE. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON THE PROPER WASHING OF THE BRIGHT ALUMINUM MOLDINGS TO AVOID THE MOLDINGS FROM GETTING DAMAGED. Read More »
This warranty administration bulletin provides information on GM?s policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in park. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin provides Information on Using Voice Pass-Thru to Access Voice Recognition Commands on Cell Phone and how it does not work on models equipped with IOA and IOB radios. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport ... Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4). Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Read More »
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis. Read More »
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered. Read More »
This Preliminary information communicates to the technician, that they may be working on a concern of a Service Driver Assist System Message with B172E stored in history Do not replace any parts. Read More »
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This preliminary informational bulletin provides information regarding the need to relearn the auto/start and stop feature on vehicles equipped after a repair has been completed on the vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Read More »
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4). Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO ENABLE THE 4G LTE WIFI ON NEWLY DELIVERED VEHICLES FOR SOME VEHICLES THAT WERE NOT SHIPPED WITH THE FEATURE NOT ENABLED. Read More »
THIS TECHNICAL BULLETIN PROVIDES DIAGNOSTIC TIPS TO HELP CORRECT MULTIPLE CONCERNS REGARDING THE USB PORT BEING INOPERATIVE OR UNABLE TO PLAY MUSIC THROUGH THE USB PORT. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE. Read More »
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near Read More »
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ... Read More »
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits. Read More »
This informational bulletin provides information on the proper ways to remove or replace the key cylinder covers due to somevehicleshavingthe key cylinders hidden during the time of delivery. Read More »
This informational bulletin provides information on Normal Radio Display Operation ? Display Does Not Remain Off at Times After Being Turned Off in Settings and no parts should be replaced due to this condition. Read More »
This Technical bulletin provides a procedure to replace the radio to correct radio personalization settings on the infotainment display and a blank HVAC pop-up selecting HVAC Control settings. Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This technical bulletin provides repair information to correct a customer concern of an intermittent blank or flickering driver information center (DIC). Read More »
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This technical bulletin provides a procedure to reprogram the radio to correct a condition of Apple Carplay Will Not Launch After 1124 Key Cycles and Displays Message Advising to Connect a Supported Device via USB Even Though One is ... Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This technical bulletin provides a procedure to reprogram the HMI module to correct a condition of Radio Intermittently Starts At Home Screen Unwanted and Unable To Enter Certain Addresses Using The Touch Screen due to a calibration ... Read More »
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Read More »
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Read More »
This technical bulletin provides a procedure to reprogram the radio to correct conditions of Distorted Outbound Audio During Bluetooth Phone Calls due to a software concern. Read More »
This technical bulletin provides a procedure to reprogram the radio to correct a condition of Apple Carplay Will Not Launch After 1124 Key Cycles and Displays Message Advising to Connect a Supported Device via USB Even Though One is ... Read More »
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Read More »
This informational bulletin provides Information on Using Voice Pass-Thru to Access Voice Recognition Commands on Cell Phone and how it does not work on models equipped with IOA and IOB radios. Read More »
This technical bulletin provides a procedure to turn the audible feedback option on and off in the radio settings to prevent an audible beep will occur when scrolling from page 1 to page 2 of the OnStar menu, which may be interpreted as a ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Read More »
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER, RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS. Read More »
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of ... Read More »
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin provides a procedure to disengage the jammed parts and release the gears for proper function caused by the mechanical of the height adjustment being jammed, not broken creating a condition of difficult to adjust ... Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary information communicates to the technician where to find the engine identification tag and what information on that tag to use during programming of someengine control modules. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months). Read More »
This Preliminary information communicates additional diagnosticsand repairto assist in resolving a malfunction indicator lampillumination due to any combination of diagnostic trouble codes P0068 P0101 P0106 P0171 P0131 P0137 P0324 P0326 ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Read More »
This Preliminary information communicates the frontview camera will not calibrate / learn. Update GDS 2 to the latest Diagnostic package 2017.3.1 release 04/03/17. Then go back and do the learn. Read More »
This Preliminary information communicates The front camera will not calibrate / learn. Update GDS 2 to the lasted Diagnostic package 2017.3.1 release 04/03/17. Than go back and do the learn. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P05CE stored. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P05CE STORED. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT GENERAL MOTORS AND GENERAL MOTORS OF CANADA COMPANY DO NOT SUPPORT CROSS BORDER SALES. Read More »
This engineering informational bulletin is requesting information from the field of vehicles with the condition of a SES light on with one or more DTC's set. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA. Read More »
THIS INFORMATIONAL BULLETIN IS TO INFORM DEALERS OF SPECIAL PROCEDURES NECESSARY WHEN TOWING A TRAILER OR WHEN TOWING THE VEHICLE BEHIND A RECREATIONAL VEHICLE. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA. Read More »
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO INTRODUCE THE 2017 GMC ACADIA TO HELP THE SERVICE DEPARTMENT PERSONNEL BECOME FAMILIAR WITH SOME OF THE VEHICLE?S NEW FEATURES AND TO DESCRIBE SOME OF THE ACTION THEY WILL NEED TO TAKE ... Read More »
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. Read More »
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores Read More »
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not. Read More »
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near Read More »
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns. Read More »
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service AWD Lamp illuminated on the Driver Information Center (DIC) ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service AWD Lamp illuminated on the Driver Information Center (DIC) ... Read More »
This service bulletin provides repair information to correct a customer concern of seeing an intermittent Shift to Park message displayed while vehicle is in Park. Read More »
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and ... Read More »
Customer Satisfaction Program - On certain vehicles, equipped with the second row bench seats (RPO ABC or ABA) may have a condition in which the second row middle seat belt buckle can fall down between the second row bench seats and be ... Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This engineering Information (EI) ends the need for information from the field for a condition of oil leaking from the valve rocker arm oil control valve. If a vehicle is encountered with this condition, refer to SI for further diagnosis. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
N192218430 - Customer Satisfaction Program. During service, certain vehicles equipped with OnStar (RPO UE1), may have received an incorrect and partially programmed/configured replacement OnStar module. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary information communicates information to let dealers know that the sunshade catch is available and not to replace sunroof housing. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This technical bulletin provides a procedure for replacing the oil pump, power brake booster and power brake booster vacuum hose to eliminate a hard brake pedal and/or air type noise heard upon brake apply due to oil in the brake booster. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Read More »
Certain 2017 model year Buick LaCrosse or GMC Acadia vehicles, that have had an engine replacement may have the wrong torque applied to front cradle-to-body bolts (M14) and front cradle stabilizer brackets-to-body bolts (M10). Read More »
Intermittent Operation of Key Fobs, Door Unlock Inoperative ?No Remote Detected? Message with Possible TPM MIL Some customers may comment on intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Read More »
Clicking Noise from Front Wheels While Turning at Slow Speeds Condition Some customers may comment on a clicking noise emanating from the front wheels location. Read More »
Reduced Steering Assist Message with DTC C0460 Sym 5A Condition Some customers may comment on a Reduced Steering Assist message on the DIC with no loss of steering assist. During diagnosis a technician may find DTC C0460 Sym 5A. Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Information for Fleet Vehicles ? Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. Read More »
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Read More »
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. Read More »
This technical bulletin provides a procedure for checking for not completely installed propshafts, if found the cause of the vibration and/or noise. Read More »
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin provides repair information to correct a customer concern of the front floor console armrest latch will not latch and/or stay closed. Read More »
17079 - Service Update. Incorrect heat treatment processing of the ring gear installed in the Power Transfer Unit (PTU) may result in the possible loss of a gear tooth. Replace the Power Transfer Unit (PTU). Read More »
This technical bulletin provides a procedure to replace the garage door opener transmitter to correct a condition of poor range for the garage door opener. Read More »
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits. Read More »
This Preliminary Information communication provides information to the technician about vehicles with an intermittent loss of gridlines in the rear camera display screen and a "Service Rear Vision System" message that both happen at the ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure to reprogram the ECM to the latest calibrations to correct the customers concern of the the MIL on with code P05CE set. Read More »
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Technical bulletin provides a procedure to replace the radio to correct radio personalization settings on the infotainment display and a blank HVAC pop-up selecting HVAC Control settings. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
17128-Service Update. Certain vehicles may have a condition in which the heating, ventilation, and air conditioning (HVAC) control module was misbuilt. This may cause the HVAC system control to be intermittently disabled. Read More »
This engineering information bulletin is requesting information on vehicles that have the condition of A/C Inoperative and/or Compressor Seizure. Read More »
This Preliminary information communicates poor heater performance or uneven heat side-to-side. Advised how to do an immediate recalibration and will be updated once a permanent correction is available. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT WHEN ADJUSTING THE HEATER-VENT-AIR CONDITIONING CONTROLS THE HEATER-VENT-AIR CONDITIONING DISPLAY IS BLANK. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil. Read More »
