Technical Service Bulletins (TSBs) for the 2021 Tahoe are official communications between Chevrolet & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to a Popping Noise Heard On Hard Turns and/or Going Over Speed Bumps, Creaking Noise While Turning Wheel Left and/or Right, Clicking ... Read More »
This service bulletin provides repair information to correct a customer concern of Service Driver Assist and/or Take Steering Messages on Start-up, Advanced Driver Assist Systems (ADAS) Features Not Available with DTCs U1614, U1615, U1616 ... Read More »
Customer Satisfaction Program. On certain vehicles with a special service sales package and radio infotainment system (RPOs 5W4 and IOR), the left hand buttons on the backside of the steering wheel currently enable favorites instead of ... Read More »
This service bulletin provides repair information to correct a customer concern of Service Driver Assist and/or Take Steering Messages on Start-up, Advanced Driver Assist Systems (ADAS) Features Not Available. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
This Preliminary information communicates an issue with a service column lock message with DTC U3000 sym71,72 or 96 and engineering released updated software to correct this concern. Read More »
This Preliminary information communicates an issue with a service column lock message with DTC U3000 sym71,72 or 96 and engineering released updated software to correct this concern. Read More »
This technical bulletin provides repair information to correct a customer concern of Service Power Steering Message Displayed in DIC, DTC?U3000?44 Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Service Driver Assist and/or Take Steering Messages on Start-up, Advanced Driver Assist Systems (ADAS) Features Not Available. Read More »
This Preliminary information communicates A diagnostic tip from root causing DTC: C1197 caused by a pinched air inlet hose to the suspension compressor air leveling system. Read More »
This Preliminary information communicates a tip when diagnosing an inoperative air leveling suspension system and to repair any loss of comm DTC's with the power window motors first. Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Dealers are to replace both the front air springs. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates an issue with a clunk pop squeak type noise from the rear of the vehicle and dealerships are to inspect the torque of the rear sway bar links. Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This Preliminary information communicates the proper component naming and labor operation codes for the air leveling system RPO F47and the Electronic Suspension Control System RPO Z95 Read More »
This Preliminary information communicates a diagnostic tip for a thump, click, pop, clunk type noise that is heard from the front end. Dealers are to inspect for something contacting the grill shutters as they open and close. Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary information communicates a tip when diagnosing an inoperative air leveling suspension system and to repair any loss of comm DTC's with the power window motors first. Read More »
This technical bulletin provides a procedure to remove the conduit from the harness for the accelerometer to correct the condition of Message a??Service Suspension Systema?? Displayed and/or DTC C102Exx. Read More »
This technical bulletin provides a procedure to remove the conduit from the harness for the accelerometer to correct the condition of Message a??Service Suspension Systema?? Displayed and/or DTC C102Exx. Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Dealers are to replace both the front air springs. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates the proper component naming and labor operation codes for the air leveling system RPO F47and the Electronic Suspension Control System RPO Z95 Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to a Popping Noise Heard On Hard Turns and/or Going Over Speed Bumps, Creaking Noise While Turning Wheel Left and/or Right, Clicking ... Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Dealers are to replace both the front air springs. Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Engineering is working on a fix. Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related ... Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This Preliminary information communicates information to to direct dealer to inspect W12RCL?Blunt Cut - Left Rear Cargo Trim wiring if normal SI diagnostics do not correct concern. Read More »
This service bulletin provides information to dealership personnel that after performing a brake inspection, brake pad replacement, or any other repair that requires the caliper piston to be reseated may be causing DTC C05B0 to falsely ... Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Dealers are to replace both the front air springs. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing ?D? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or 8-6 ... Read More »
Customer Satisfaction Program (Programming Suspended/Resumed) - Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This service bulletin provides information to dealership personnel that after performing a brake inspection, brake pad replacement, or any other repair that requires the caliper piston to be reseated may be causing DTC C05B0 to falsely ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Engineering is working on a fix. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
Service Update Bulletin. Certain vehicles may have an erratic signal coming from the engine manifold absolute pressure (MAP) sensor. Customers may notice the service engine soon (SES) lamp illuminate or was illuminated and turned off. Read More »
This Preliminary information communicates an issue with premature brake pad life and engineering is working on release new pad lining material. Read More »
Customer Satisfaction Program - Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This preliminary information bulletin instructs to technicians to check the trigger wheel for interfering with the timing chain, and adding a shim to the camshaft position sensor. Read More »
This preliminary information bulletin instructs to technicians to check the trigger wheel for interfering with the timing chain, and adding a shim to the camshaft position sensor. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to one or more of the following condition Stalls, Crank with no star, Check ... Read More »
This Preliminary information communicates that the performance air cleaner kit (cold air intake system) can only be installed on vehicles that had the option ordered for the vehicle when it was produced. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
Service Update - certain vehicles may have a condition where the engine oil cooler line is not fully seated into the quick connect at the radiator. Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the Engine Control Module. Read More »
This Preliminary information communicates During inspection of the vehicle for an unrelated concern the technician may notice that one or more of the following Cylinder Deactivation Performance DTC(s) P3498, P3499, P349A, P349B, P349C, ... Read More »
This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides a procedure to replace the valve lifter and guides to correct customer concerns of Poor Engine Performance, Engine Misfires, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0300, P0301, P0302, P0303, ... Read More »
This service bulletin provides a repair procedure to correct customer concerns of Service Emissions System Displayed on DIC, MIL Illuminated with DTC P249C and/or P20E8 Set. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This service bulletin provides a repair procedure to correct customer concerns of Service Emissions System Displayed on DIC, MIL Illuminated with DTC P249C and/or P20E8 Set. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This informational bulletin provides Changes to the Automatic Stop/Start feature for Certain 2021 Escalade models, Silverado 1500, Suburban, Tahoe, Sierra 1500, Yukon models Equipped with RPO NSS. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin provides repair information for Engine Wire Harness Chafing to correct customer concerns of IPC Gauges Sweep, IPC Warning Message, SES/Check Engine/MIL, No Start/ No Crank, Runs Rough, Stalls, Reduced Engine Power, ... Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin provides a procedure to replace the valve lifter and guides to correct customer concerns of Poor Engine Performance, Engine Misfires, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0300, P0301, P0302, P0303, ... Read More »
This service bulletin provides a procedure to replace the valve lifter and guides to correct customer concerns of Poor Engine Performance, Engine Misfires, Malfunction Indicator Lamp (MIL) Illuminated - DTC P0300, P0301, P0302, P0303, ... Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up on the glow plug causing a premature failure. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
Service Update- Certain vehicles may have a condition where the engine control module calibrations can be enhanced to improve the accuracy of certain diagnostic tests. Dealers are to reprogram the engine control module. Read More »
This informational bulletin provides Changes to the Automatic Stop/Start feature for Certain 2021 Escalade models, Silverado 1500, Suburban, Tahoe, Sierra 1500, Yukon models Equipped with RPO NSS. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
Service Update Bulletin - Certain vehicles may have a condition where the engine control module has an incorrect calibration. Dealers are to reprogram the engine control module. Read More »
This technical bulletin provides service information to correct a customer concern of HVAC Heat Intermittently Inoperative, DTCs B2B05 and/or B2B06 Set. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This service bulletin provides a procedure to repair a customer concern of Stop/Start System Inhibited / IBS / Battery Monitor with Module Malfunction Indicator Light (MIL) Illuminated - DTC U152D, P15FF, P305D, P305E, U01B0 Set. Read More »
This Preliminary information communicates to the dealer technician that if the vehicle's engine coolant reservoir has transmission fluid in it or if Glycol it found in the transmission fluid the dealer should replace the Automatic ... Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards on the rear washer hose being disconnected. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Informational bulletin advises the technician of a possible oil leak at the front cover and how to diagnose it to verify if it is coming from the seal or not. Read More »
This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This technical bulletin advises to replace the camshaft cover if found within the Julian date and the cause of a customer concern of possible oil consumption with or without DTC P06DD. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Oil Leaking from Front of Engine. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This technical bulletin advises to replace the camshaft cover if found within the Julian date and the cause of a customer concern of possible oil consumption with or without DTC P06DD. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, Shake, Vibration, Harsh Shift, Delayed Shift and/or ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to oil leaking from the lower oil pan seal area. Read More »
This Preliminary information communicates to the dealer technician that if the vehicle's engine coolant reservoir has transmission fluid in it or if Glycol it found in the transmission fluid the dealer should replace the Automatic ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This Preliminary information communicates to dealership technicians to perform a sweep of the coolant flow control valve and test the circuits before replacing the Engine Coolant Flow Control Valve, and to assist engineering in root ... Read More »
This Preliminary information communicates to technicians to replace the ECM and affected sensor if diagnostics leads to replacement of the ECM. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, ... Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This Preliminary information communicates to the dealer an issue where a vehicle may be exhibiting an engine noise condiion. The dealer is instructed on how to isolate the noise to a specific area of the engine for further diagnosis. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine ... Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This Preliminary information communicates information on a No Crank / No Start concern caused by a No Fob Detected message caused by an internal fault of the BCM. Dealer is to replace the BCM to correct this concern. Read More »
This informational bulletin provides Changes to the Automatic Stop/Start feature for Certain 2021 Escalade models, Silverado 1500, Suburban, Tahoe, Sierra 1500, Yukon models Equipped with RPO NSS. Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Read More »
This Preliminary information communicates to dealership technicians to perform a sweep of the coolant flow control valve and test the circuits before replacing the Engine Coolant Flow Control Valve, and to assist engineering in root ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates and issue with a SES MIL and the BCM keeping the ignition main relay on after the vehicle is turned off. Dealers are to replace the BCM. Read More »
Service Update. On certain vehicles the clamp may not be properly aligned and positioned on the hose, or the hose is rolled over on the pump port. The improper assembly can quickly develop into a significant leak early in the truck?s life. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (VINS re-opened, software updated). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates and issue if the BSCM is replaced it may prevent any over the air updates to the vehicle and in the meantime to prevent this the dealership needs to replace the complete master cylinder assembly. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
Service Update - certain vehicles may have a condition where the engine oil cooler line is not fully seated into the quick connect at the radiator. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
Service Update Bulletin - Certain vehicles may have a condition where the engine control module has an incorrect calibration. Dealers are to reprogram the engine control module. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
Emission Recall. General Motors has decided to conduct a voluntary emissions recall involving certain vehicles equipped with a performance air intake system (LPO RVK or 5W7). Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder. Read More »
This Preliminary information communicates to technicians to modify the camshaft housing cover insulator by removing the stand off identified in the attached pictures. Read More »
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine ... Read More »
This Preliminary information communicates an issues with an SES MIL and DTC P2B87 setting. Engineering is working on releasing updated BCM cals to correct the concern. Read More »
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates to technicians a P205B intermittently setting is under investigation by engineering and to clear the code and release the vehicle. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Reductant Tank Temperature Sensor Performance and/or Service Emissions System ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary information communicates a issue where the Can bus 1 data line is being corrupted by a aftermarket lighting module or poor connection installed by a Police Upfitter. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder, stall or high transmission ... Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder, stall or high transmission ... Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder or stall concern they should ... Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder or stall concern they should ... Read More »
Service Update. On certain vehicles the clamp may not be properly aligned and positioned on the hose, or the hose is rolled over on the pump port. The improper assembly can quickly develop into a significant leak early in the truck?s life. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated. Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This bulletin advises the tech that there are extra characters on the fuel injector and to ignore the last numbers when identifying flow rate. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to technicians a P205B intermittently setting is under investigation by engineering and to clear the code and release the vehicle. Read More »
This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in performance in regards to the customers concerns. Read More »
This Preliminary information communicates an issue where there is no selection to reset the fuel filter life in the IPC and engineering is working on a fix. Read More »
This Preliminary information communicates an issue where there is no selection to reset the fuel filter life in the IPC and engineering is working on a fix. Read More »
This Preliminary information communicates an issue where there is no selection to reset the fuel filter life in the IPC and engineering is working on a fix. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This service bulletin provides diagnostic information for technicians in cases of an ETRS system fault or a no start condition - If the vehicle needs to be moved, it is recommended to use wheel dollies, tire skates or the NEW Manual Park ... Read More »
This technical bulletin provides a procedure to program the TCM and replace the control valve body if the conditions are found to be the cause of the failure you the valve body. Read More »
This service bulletin advises the technician to check if the transmission cooler lines are twisted to correct customer concerns of Harsh Shift, Shudder, Surge, Stall, Transmission Overheating and/or High Transmission Fluid Temperature. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This service bulletin provides repair information for Engine Wire Harness Chafing to correct customer concerns of IPC Gauges Sweep, IPC Warning Message, SES/Check Engine/MIL, No Start/ No Crank, Runs Rough, Stalls, Reduced Engine Power, ... Read More »
This Preliminary information communicates diagnostic tips on how to resolve a issues with vehicles that will not power up after a can bus 2 issue, lightning strike, or a failed over the air update. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This service bulletin provides a procedure to replace the front wheel drive shaft to correct a customer concern of a Squeak/Chirp Noise from Front Axle in 2wd. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This Preliminary information communicates to the dealer, a potential rough running condition following an autostop event that is caused by the incorrect crankshaft position sensor. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
This engineering information (EI) closure ends the need for gathering further information from technicians in regard to a binding, moan and/or chatter type sound heard from the rear of the vehicle when making slow parking lot maneuvers. Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing a??Da?? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This Preliminary information communicates diagnostic tips on how to resolve a issues with vehicles that will not power up after a can bus 2 issue, lightning strike, or a failed over the air update. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This service bulletin advises the technician to check if the transmission cooler lines are twisted to correct customer concerns of Harsh Shift, Shudder, Surge, Stall, Transmission Overheating and/or High Transmission Fluid Temperature. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin provides a procedure to replace the rear differential fluid to correct the rear clutches from chattering, which create a moan type noise. Read More »
This service bulletin provides information for the technician that may experience a condition when after performing a DTC Clear/Reset on the TCM during diagnosis or after completion of a transmission repair or replacement, the DTCs did ... Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This Preliminary information communicates diagnostic tips on how to resolve a issues with vehicles that will not power up after a can bus 2 issue, lightning strike, or a failed over the air update. Read More »
This Preliminary information communicates diagnostic tips on how to resolve a issues with vehicles that will not power up after a can bus 2 issue, lightning strike, or a failed over the air update. Read More »
This Preliminary information communicates a tip when diagnosing an inoperative air leveling suspension system and to repair any loss of comm DTC's with the power window motors first. Read More »
This service bulletin provides information for the technician that may experience a condition when after performing a DTC Clear/Reset on the TCM during diagnosis or after completion of a transmission repair or replacement, the DTCs did ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This service bulletin provides diagnostic information for technicians in cases of an ETRS system fault or a no start condition - If the vehicle needs to be moved, it is recommended to use wheel dollies, tire skates or the NEW Manual Park ... Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This technical bulletin provides a procedure to program the TCM and replace the control valve body if the conditions are found to be the cause of the failure of the valve body. Read More »
This technical bulletin provides a procedure to replace the rear diff fluid to correct the rear clutches from chattering, which create a moan type noise. Read More »
This service bulletin provides information for the technician that may experience a condition when after performing a DTC Clear/Reset on the TCM during diagnosis or after completion of a transmission repair or replacement, the DTCs did ... Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This Preliminary information communicates that improper installation of the valve body may cause an unawanted Service Transmission message with no DTC'S. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This Preliminary information communicates and issues with Fuse F49 blowing causing a SES MIL and a Service Theft Deterrent System message displayed in the DIC. Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This information advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF causing the customers concern. Read More »
This Preliminary information communicates to the dealer technician that if the vehicle's engine coolant reservoir has transmission fluid in it or if Glycol it found in the transmission fluid the dealer should replace the Automatic ... Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing a??Da?? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or ... Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder, stall or high transmission ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder, stall or high transmission ... Read More »
This service bulletin provides diagnostic information for technicians in cases of an ETRS system fault or a no start condition - If the vehicle needs to be moved, it is recommended to use wheel dollies, tire skates or the NEW Manual Park ... Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing a??Da?? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or ... Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, Shake, Vibration, Harsh Shift, Delayed Shift and/or ... Read More »
This Preliminary information communicates to the dealer technician that if the vehicle's engine coolant reservoir has transmission fluid in it or if Glycol it found in the transmission fluid the dealer should replace the Automatic ... Read More »
This informational bulletin provides graphs to help identify possible issues that may cause shaking and shudders and what may be the cause of said issue. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Power Floor Console Armrest will not lock in place and/or the console ... Read More »
This Preliminary information communicates and issues with Fuse F49 blowing causing a SES MIL and a Service Theft Deterrent System message displayed in the DIC. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Engine Coolant Reservoir Being Overfilled with Discolored Coolant, Shudder, ... Read More »
This service bulletin provides diagnostic information for technicians in cases of an ETRS system fault or a no start condition - If the vehicle needs to be moved, it is recommended to use wheel dollies, tire skates or the NEW Manual Park ... Read More »
This Preliminary information communicates to technicians to advise dealership technicians to inspect the camshaft exciter wheel and replace it if necessary. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder, stall or high transmission ... Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder or stall concern they should ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This Preliminary information communicates to the dealer technician to replace the transmission valve body on 2019-2021 10 speed transmissions to correct DTCs P2812 and P2814 setting if Service Information does not lead to root case of ... Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This Preliminary information communicates to the dealer technician that if a customer comments that their vehicle equipped with a 6L80, 6L90, 8L90, 10L80, or 10L1000 transmission has a harsh shift, shudder or stall concern they should ... Read More »
This Preliminary information communicates to the dealer technician that the 10L80 transmission has been place on a part restriction. Dealers are to contact the Product Quality Center before replacing the transmission assembly. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets turning off during an Auto Stop event, which is normal operation. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets turning off during an Auto Stop event, which is normal operation. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Preliminary information communicates and issues with Fuse F49 blowing causing a SES MIL and a Service Theft Deterrent System message displayed in the DIC. Read More »
This Preliminary information communicates to the dealer technician that the 10L80 transmission has been place on a part restriction. Dealers are to contact the Product Quality Center before replacing the transmission assembly. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Engineering is working on a new cal. Read More »
This Preliminary information communicates an issue with the Transmission Control Module (TCM) not communicating and causing a no crank concern. Dealers are to reprogram the TCM to correct the concern. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
This Preliminary information communicates an issues with false codes setting in vehicles due to timing issues with modules Engineering is working on a fix Read More »
This Preliminary information communicates an issues with false codes setting in vehicles due to timing issues with modules Engineering is working on a fix Read More »
This Preliminary information communicates to the dealer technician that the 10L80 transmission has been place on a part restriction. Dealers are to contact the Product Quality Center before replacing the transmission assembly. Read More »
This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern. Read More »
This Preliminary information communicates an issues with false codes setting in vehicles due to timing issues with modules Engineering is working on a fix Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:SEALS/GASKETS
This Informational bulletin advises the technician of a possible oil leak at the front cover and how to diagnose it to verify if it is coming from the seal or not. Read More »
This service bulletin provides diagnostic information for technicians in cases of an ETRS system fault or a no start condition - If the vehicle needs to be moved, it is recommended to use wheel dollies, tire skates or the NEW Manual Park ... Read More »
This Preliminary information communicates that engineering is investigating a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates that engineering is investigating a repair for a chirp noise associated with the front axle assembly. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This Preliminary information communicates a vehicle may come to the dealer with a complaint of no start, stalling, rough idle, no acceleration, loss of power, erratic shifting, fuel gauge inoperative, MIL illuminated with various codes ... Read More »
This Preliminary information communicates a vehicle may come to the dealer with a complaint of no start, stalling, rough idle, no acceleration, loss of power, erratic shifting, fuel gauge inoperative, MIL illuminated with various codes ... Read More »
This technical bulletin provides a procedure to program the TCM and replace the control valve body if the conditions are found to be the cause of the failure you the valve body. Read More »
This Preliminary information communicates a vehicle may come to the dealer with a complaint of no start, stalling, rough idle, no acceleration, loss of power, erratic shifting, fuel gauge inoperative, MIL illuminated with various codes ... Read More »
This Preliminary information communicates a issue where the Can bus 1 data line is being corrupted by a aftermarket lighting module or poor connection installed by a Police Upfitter. Read More »
This Preliminary information communicates a vehicle may come to the dealer with a complaint of no start, stalling, rough idle, no acceleration, loss of power, erratic shifting, fuel gauge inoperative, MIL illuminated with various codes ... Read More »
This service bulletin provides information for dealers/technicians on MDI 2 Required When Programming Vehicles with Vehicle Intelligence Platform (VIP). Read More »
This service bulletin provides a repair procedure to correct customer concerns of Service Emissions System Displayed on DIC, MIL Illuminated with DTC P249C and/or P20E8 Set. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This informational bulletin provides Changes to the Automatic Stop/Start feature for Certain 2021 Escalade models, Silverado 1500, Suburban, Tahoe, Sierra 1500, Yukon models Equipped with RPO NSS. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin provides repair information for Engine Wire Harness Chafing to correct customer concerns of IPC Gauges Sweep, IPC Warning Message, SES/Check Engine/MIL, No Start/ No Crank, Runs Rough, Stalls, Reduced Engine Power, ... Read More »
This service bulletin provides information for dealers/technicians on MDI 2 Required When Programming Vehicles with Vehicle Intelligence Platform (VIP). Read More »
Service Update. Certain Vehicles may not have the emergency light flashers enabled. Dealers are to reprogram the body control module and lighting control module. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Preliminary information communicates a issue where the rear windshield wipers will not be in the park position and will cause the rear back glass not to open with the switch or the RKE fob. This explains how to repair that concern. Read More »
This Preliminary information communicates an issues with an SES MIL, A/C blowing warm air and DTC's B1AA3 U3018 U3505 due to Fuse F4DR open. Dealers are to inspect the wiring in the front floor console. Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This technical bulletin provides a procedure to correct the condition of Service Restraint System Message / Air Bag Warning MIL / DTC B14DC Set. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This service bulletin provides repair information to correct a customer concern of Black Radio Display Screen (Triangle and Camera with Slash Through it) with DTCs B1A62 82 and 86 Setting Current in Video Processing Module (VPM). Read More »
This service bulletin provides repair information to correct a customer concern of Black Radio Display Screen (triangle and camera with the slash through it) with DTCs B1A62 82 and 86 setting current in Video Processing Module (VPM). Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This technical bulletin provides a procedure to correct the condition of Service Restraint System Message / Air Bag Warning MIL / DTC B14DC Set. Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This service bulletin provides information to dealership personnel that after performing a brake inspection, brake pad replacement, or any other repair that requires the caliper piston to be reseated may be causing DTC C05B0 to falsely ... Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This service bulletin provides information for the technician that may experience a condition when after performing a DTC Clear/Reset on the TCM during diagnosis or after completion of a transmission repair or replacement, the DTCs did ... Read More »
This Preliminary information communicates a issue where the Can bus 1 data line is being corrupted by a aftermarket lighting module or poor connection installed by a Police Upfitter. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This informational bulletin provides Changes to the Automatic Stop/Start feature for Certain 2021 Escalade models, Silverado 1500, Suburban, Tahoe, Sierra 1500, Yukon models Equipped with RPO NSS. Read More »
This service bulletin provides information for the technician that may experience a condition when after performing a DTC Clear/Reset on the TCM during diagnosis or after completion of a transmission repair or replacement, the DTCs did ... Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue with the Body Control Module setting DTC: P0606 and turning on a Check Engine Lamp. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This technical bulletin provides repair information to correct a customer concern of Black Radio Display Screen (Triangle and Camera with Slash Through it) with DTCs B1A62 82 and 86 Setting Current in Video Processing Module (VPM). Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue with the Body Control Module setting DTC: P0606 and turning on a Check Engine Lamp. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This informational bulletin advises the tech to inspect the transfer case motor electrical connectors for possible damage or corrosion that might be caused by a damage grommet inside the electrical connector. Read More »
This technical bulletin provides a procedure to program the TCM and replace the control valve body if the conditions are found to be the cause of the failure of the valve body. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This Preliminary information communicates an issues with the side blind alert icon not working properly after a short range radar is replaced. Dealers are to perform a return to factory settings to correct the issue. Read More »
This Preliminary information communicates an issue with an OTA pending message still displayed after an OTA event and how to reset/clear the message. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information for the technician that may experience a condition when after performing a DTC Clear/Reset on the TCM during diagnosis or after completion of a transmission repair or replacement, the DTCs did ... Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This service bulletin provides information for dealers/technicians on MDI 2 Required When Programming Vehicles with Vehicle Intelligence Platform (VIP). Read More »
This Preliminary information communicates and issues with Fuse F49 blowing causing a SES MIL and a Service Theft Deterrent System message displayed in the DIC. Read More »
This service bulletin provides diagnostic/repair information to correct a customer concern of Cellphone not Charging or USB Receptacle Inoperative. Read More »
This service bulletin provides repair information to correct a customer concern of DTC B1038 SYM64 set in the BCM and Door Ajar Message on Driver Information Center (DIC). Read More »
This technical bulletin provides a procedure to remove the conduit from the harness for the accelerometer to correct the condition of Message a??Service Suspension Systema?? Displayed and/or DTC C102Exx. Read More »
This Preliminary information communicates an issue with the GDS2 scan tool not being able to communication with the front view camera module and provides a work around until GDS2 is fixed. Read More »
This service bulletin provides repair information on release of Radio Software Version V160 Update to correct customer concerns of radio software issues. Read More »
This technical bulletin provides a procedure to remove the conduit from the harness for the accelerometer to correct the condition of Message a??Service Suspension Systema?? Displayed and/or DTC C102Exx. Read More »
This service bulletin provides a procedure to repair a customer concern of Stop/Start System Inhibited / IBS / Battery Monitor with Module Malfunction Indicator Light (MIL) Illuminated - DTC U152D, P15FF, P305D, P305E, U01B0 Set. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue with the Body Control Module setting DTC: P0606 and turning on a Check Engine Lamp. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer other wise found by a possible faulty trailer connector. Read More »
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention. Read More »
This technical bulletin provides a procedure to replace the fuel injector and the wiring harness to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated with DTC P0201, P0202, P0203, P0204, P0205, P0206 and/or P0216 ... Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to a Forward Collision Icon Message Illuminated on Driver Information Center (DIC) and/or No DTCs Set. Read More »
This technical bulletin provides repair information to correct a customer concern of Malfunction Indicator Lamp Illuminated with DTC P06DD, P2B60, P26BB, P1098 Set. Read More »
This service bulletin provides repair information to correct a customer concern of DTC B1038 SYM64 set in the BCM and Door Ajar Message on Driver Information Center (DIC). Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a Forward Collision Icon Message Illuminated on Driver Information Center (DIC) ... Read More »
This service bulletin provides repair information to correct a customer concern of DTC B1038.64 set in the BCM and Door Ajar Message on Driver Information Center (DIC). Read More »
This Engineering Information (EI) Closure ends the need for further information from the field regarding No Heat from Driver Side Inboard Dash Duct and/or Weak Heat On Driver Side. Read More »
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This Preliminary information communicates and issues with Fuse F49 blowing causing a SES MIL and a Service Theft Deterrent System message displayed in the DIC. Read More »
This Preliminary information communicates an issue with the GDS2 scan tool not being able to communication with the front view camera module and provides a work around until GDS2 is fixed. Read More »
This Preliminary information communicates an issues with an SES MIL, A/C blowing warm air and DTC's B1AA3 U3018 U3505 due to Fuse F4DR open. Dealers are to inspect the wiring in the front floor console. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This technical bulletin provides repair information to correct a customer concern of Power to the 110V/120 Outlet is Interrupted During an Auto Stop/Start Event. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This preliminary information bulletin instructs to technicians to check the trigger wheel for interfering with the timing chain, and adding a shim to the camshaft position sensor. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This Preliminary information communicates and issue with unwanted content theft alarm going off for no reason and to reprogram the BCM to correct the issue. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Liftgate Ajar Lamp illuminated on Driver Information Center (DIC) with ... Read More »
Emission Recall. General Motors has decided to conduct a voluntary emissions recall involving certain vehicles equipped with a performance air intake system (LPO RVK or 5W7). Read More »
This technical bulletin provides repair information to correct a customer concern of Rear Access Open Message Illuminated in DIC when Liftgate is Closed. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Malfunction Indicator Lamp (MIL) illuminated on Driver Information Center ... Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This preliminary information bulletin instructs to technicians to use the Picoscope or a make physical inspection to check for a suspected bent target wheel on the camshaft. Read More »
This service bulletin provides repair information to correct a customer concern of Service Driver Assist and/or Take Steering Messages on Start-up, Advanced Driver Assist Systems (ADAS) Features Not Available. Read More »
This Preliminary information communicates information on a No Crank / No Start concern caused by a No Fob Detected message caused by an internal fault of the BCM. Dealer is to replace the BCM to correct this concern. Read More »
This Preliminary information communicates the Radio may stay on after ignition off and door opened if there is an Over The Air update pending and to review SI document ID 5778263 for Over The Air update description and operation. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Malfunction Indicator Lamp illuminated on the Driver Information ... Read More »
This technical bulletin provides repair information to correct a customer concern of SUV Vehicle Software Configuration Management Update (VeSCoM). Read More »
This technical bulletin provides repair information to correct a customer concern of SUV Vehicle Software Configuration Management Update (VeSCoM). Read More »
This service bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to concerns with the front center floor power console function and/or ... Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates to the technition instructions to replace the particulate matter sensor for a P1488 and to use the special labor operation for tracking purposes. Read More »
This service bulletin provides a procedure to splice in a missing circuit to correct a condition where certain electronics and lighting installed after an upfit will not work in accessory mode. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Liftgate Ajar Lamp illuminated on Driver Information Center (DIC) with ... Read More »
This service bulletin describes the TLC/SPS2 Module Programming Requirements for Vehicles Using GM?s New Vehicle Intelligence Platform (VIP) Module Architecture. Read More »
This Preliminary information communicates and issue with a SES MIL and the BCM keeping the ignition main relay on after the vehicle is turned off. Dealers are to replace the BCM. Read More »
Service Update. Certain vehicles may have incorrect calibration values in the Vehicle Leveling Module (VLM) software for air ride adaptive suspension. The incorrect calibration will use the incorrect loaded ride height which is 0. Read More »
This service bulletin provides repair information to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated with DTCs U1961, U1983 setting. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
Customer Satisfaction Program (Revised Service Procedure). Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the power liftgate inoperative. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the airbag lamp illuminated on the driver?s information center (DIC). Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the airbag lamp illuminated on the driver?s information center (DIC). Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
This Preliminary information communicates a cocnern where a flashing spot can intermittently show up on the radio display while in reverse. The PI advises that engineering is investigating the concern. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary Information communication requests information from the technician about vehicles that may have Bluetooth or phone projection issues. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (VINS re-opened, software updated). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Service Engine Soon Lamp being illuminated. Read More »
Customer Satisfaction Program (Programming Suspended/Resumed) - Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates and issues with Fuse F49 blowing causing a SES MIL and a Service Theft Deterrent System message displayed in the DIC. Read More »
This Preliminary information communicates and issue with programming a replacement side object detection module and engineering is working on the issue. Read More »
Customer Satisfaction Program - Certain 2021 model year Chevrolet Suburban and Tahoe vehicles, may have a condition in which the daytime running lamps may shift to a bluer shade of white in its lit appearance. Read More »
This Preliminary information communicates and issue where the drivers memory seat will not move to its full travel and dealers are to perform a SPS setup procedure to the K40D Drivers Seat Adjuster Memory Module. Read More »
This service bulletin provides repair information to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated with DTCs U1961, U1983 setting. Read More »
This Preliminary information communicates there is a Part Restriction for the Automatic Leveling Control Module and to contact the PQC to order the part. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the power liftgate inoperative. Read More »
This Preliminary information communicates an issue with a low or dead battery issue cause by the rear hvac door being jammed by an foreign object. Read More »
This service bulletin provides information and a service procedure for dealers/technicians on OnStar Over the Air Update for TTY / TDD Operation and Continuous Improvement Changes. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets turning off during an Auto Stop event, which is normal operation. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards one or more camera views showing, intermittent behavior and/or totally inoperative. Read More »
This Preliminary information communicates there is a Part Restriction for the Automatic Leveling Control Module and to contact the PQC to order the part. Read More »
This Preliminary information communicates During inspection of the vehicle for an unrelated concern the technician may notice that one or more of the following Cylinder Deactivation Performance DTC(s) P3498, P3499, P349A, P349B, P349C, ... Read More »
This Preliminary information communicates and issue with programming a replacement side object detection module and engineering is working on the issue. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This technical bulletin provides repair information to correct a customer concern of Service Power Steering Message Displayed in DIC, DTC?U3000?44 Set. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This informational bulletin provides information for dealers/technicians on Normal Characteristic - Wireless Phone Projection Audio Cuts Out Every 10 Seconds on New/Unsold Vehicles. Read More »
This technical bulletin provides repair information to correct a customer concern of Service Driver Assist and/or Take Steering Messages on Start-up, Advanced Driver Assist Systems (ADAS) Features Not Available. Read More »
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This Preliminary information communicates an issues with false codes setting in vehicles due to timing issues with modules Engineering is working on a fix Read More »
This Preliminary information communicates an issues with false codes setting in vehicles due to timing issues with modules Engineering is working on a fix Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates During inspection of the vehicle for an unrelated concern the technician may notice that one or more of the following Cylinder Deactivation Performance DTC(s) P3498, P3499, P349A, P349B, P349C, ... Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary information communicates and issue with the SES MIL on setting DTC's P0201/P0202/P0203/P0204/P0205/P0206/P0216 and instructing dealership to inspect the engine wiring harness for damage. Read More »
ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL
This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup ... Read More »
This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup ... Read More »
This Preliminary information communicates an issues after After Performing Recall N222386380 Some Police Options / Features May Have Been Unintentionally Enabled or Disabled. Dealers are to reprogram the BCM to correct these concerns. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This service bulletin provides repair information to correct a customer concern of Check Engine MIL Illuminated in DIC Set by Body Control Module with DTC P0607. Read More »
This service bulletin provides repair information to correct a customer concern of DTC B1038.64 set in the BCM and Door Ajar Message on Driver Information Center (DIC). Read More »
This Preliminary information communicates an issues with an SES MIL and DTC P2B87 setting. Engineering is working on releasing updated BCM cals to correct the concern. Read More »
This Preliminary information communicates an issues with an SES MIL and DTC P2B87 setting. Engineering is working on releasing updated BCM cals to correct the concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates an issue with high resistance in the glass breakage loop that could cause a dead battery or unwanted theft alarm. Dealers are to inspect the glass breakage loop. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2021 and newer model year vehicles with RPO ... Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Malfunction Indicator Lamp (MIL) illuminated on Driver Information Center ... Read More »
This Preliminary information communicates an issues with the odometer being incorrect after a programming event and how the dealership can resolve the issue. Read More »
This Preliminary information communicates an issues with the odometer being incorrect after a programming event and how the dealership can resolve the issue. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
This Preliminary information communicates an issues with the odometer being incorrect after a programming event and how the dealership can resolve the issue. Read More »
'(There may be future updates under this same release number.) Your vehicle keeps getting better. This vehicle software update includes the following: Refinements: a??Updates made to the overall vehicle software update process. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary information communicates to technicians a P205B intermittently setting is under investigation by engineering and to clear the code and release the vehicle. Read More »
This service bulletin provides repair information to correct a customer concern of Service Driver Assist and/or Take Steering Messages on Start-up, Advanced Driver Assist Systems (ADAS) Features Not Available with DTCs U1614, U1615, U1616 ... Read More »
Customer Satisfaction Program. On certain vehicles with a special service sales package and radio infotainment system (RPOs 5W4 and IOR), the left hand buttons on the backside of the steering wheel currently enable favorites instead of ... Read More »
This technical bulletin provides repair information to correct a customer concern of Assist Step Running Boards Inoperable and Not Functioning with Door Operation. Read More »
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This Preliminary information communicates an issues with an SES MIL and DTC P2B87 setting. Engineering is working on releasing updated BCM cals to correct the concern. Read More »
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards one or more camera views showing, intermittent behavior and/or totally ... Read More »
This Preliminary information communicates a issue where the Can bus 1 data line is being corrupted by a aftermarket lighting module or poor connection installed by a Police Upfitter. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
Customer Satisfaction Program (Revised Service Procedure). Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This Preliminary information communicates an issue with a Check Reverse Lamp message on the DIC, but the reverse light operate. Engineering working on a fix. Read More »
This Preliminary information communicates an issue with a Check Reverse Lamp message on the DIC, but the reverse light operate. Engineering has released updated cals to correct this concern. Read More »
This Preliminary information communicates an issue with a Check Reverse Lamp message on the DIC, but the reverse light operate. Engineering has released updated cals to correct this concern. Read More »
Customer Satisfaction Program - Certain 2021 model year Chevrolet Suburban and Tahoe vehicles, may have a condition in which the daytime running lamps may shift to a bluer shade of white in its lit appearance. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on a turn signal not canceling and/or mis-canceling. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on a turn signal not canceling and/or mis-canceling. Read More »
Service Update. Certain Vehicles may not have the emergency light flashers enabled. Dealers are to reprogram the body control module and lighting control module. Read More »
This Preliminary information communicates an issues with the side blind alert icon not working properly after a short range radar is replaced. Dealers are to perform a return to factory settings to correct the issue. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
Service Update Bulletin - Certain 2021 model year Chevrolet Suburban, Tahoe, and GMC Yukon vehicles may have a kink in the rear camera washer hose. Read More »
This Preliminary information communicates a issue where the rear windshield wipers will not be in the park position and will cause the rear back glass not to open with the switch or the RKE fob. This explains how to repair that concern. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This Preliminary information communicates an issue with a gurgle noise from the sunroof drains and advises customers to turn on the HVAC blower to clear the drain. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This Preliminary information communicates an issue with a gurgle noise from the sunroof drains and advises customers to turn on the HVAC blower to clear the drain. Read More »
This Preliminary information communicates a issue where the rear windshield wipers will not be in the park position and will cause the rear back glass not to open with the switch or the RKE fob. This explains how to repair that concern. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary information communicates an issues with an SES MIL, A/C blowing warm air and DTC's B1AA3 U3018 U3505 due to Fuse F4DR open. Dealers are to inspect the wiring in the front floor console. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This technical bulletin provides service information to correct a customer concern of HVAC Heat Intermittently Inoperative, DTCs B2B05 and/or B2B06 Set. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates an issue with a low or dead battery issue cause by the rear hvac door being jammed by an foreign object. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the HVAC is stuck in defrost mode and can not change to vent or any other ... Read More »
This Preliminary information communicates an issue with a gurgle noise from the sunroof drains and advises customers to turn on the HVAC blower to clear the drain. Read More »
This Preliminary information communicates a issue where the rear windshield wipers will not be in the park position and will cause the rear back glass not to open with the switch or the RKE fob. This explains how to repair that concern. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This technical bulletin provides a procedure to correct the condition of Service Restraint System Message / Air Bag Warning MIL / DTC B14DC Set. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This technical bulletin provides a procedure to correct the condition of Service Restraint System Message / Air Bag Warning MIL / DTC B14DC Set. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Check Engine Lamp illuminated on Driver Information Center (DIC) and DTC ... Read More »
This Preliminary information communicates an issue with an SIR MIL with DTC B14DC caused by the air bag connector contacting the foam in the drivers seat. Dealer to remove the foam that is contacting the air bag connector. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the Service 4WD message displayed on the driver information center (DIC). Read More »
This technical bulletin provides a procedure to replace the air bag and air bag harness to correct a condition of Airbag Malfunction Warning and Airbag Malfunction Indicator Illuminated with DTC B0001-1B due to corrosion. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This technical bulletin provides a procedure to replace the air bag and air bag harness to correct a condition of Airbag Malfunction Warning and Airbag Malfunction Indicator Illuminated with DTC B0001-1B due to corrosion. Read More »
Customer Satisfaction Program (Revised Service Procedure). Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the airbag lamp illuminated on the driver?s information center (DIC). Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the airbag lamp illuminated on the driver?s information center (DIC). Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
This Preliminary information communicates an issue with a Check Reverse Lamp message on the DIC, but the reverse light operate. Engineering has released updated cals to correct this concern. Read More »
This Preliminary information communicates an issue with a Check Reverse Lamp message on the DIC, but the reverse light operate. Engineering has released updated cals to correct this concern. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the airbag lamp illuminated on the driver?s information center (DIC). Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the airbag lamp illuminated on the driver?s information center (DIC). Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE:SOFTWARE
This Preliminary information communicates an issue with an SIR MIL with DTC B14DC caused by the air bag connector contacting the foam in the drivers seat. Dealer to remove the foam that is contacting the air bag connector. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This technical bulletin provides a procedure to correct the condition of Service Restraint System Message / Air Bag Warning MIL / DTC B14DC Set. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Power Floor Console Armrest will not lock in place and/or the console ... Read More »
This Preliminary information communicates an issue with a service column lock message with DTC U3000 sym71,72 or 96 and engineering released updated software to correct this concern. Read More »
This Preliminary information communicates an issue with a service column lock message with DTC U3000 sym71,72 or 96 and engineering released updated software to correct this concern. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary information communicates an issue with a wind noise while driving at highway speeds and dealers are to inspect the body harness pass through for being full seated into the cowl. Read More »
This technical bulletin provides a step by step procedure to replace the pressure relief valve due to Flutter Noise from Right Rear Corner of the Vehicle. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin has you remove flash and reinstall clip to correct condition of Arm Rest Does Not Lock in Position and Slides Back and Forth. Read More »
This Preliminary information communicates an issue with high resistance in the glass breakage loop that could cause a dead battery or unwanted theft alarm. Dealers are to inspect the glass breakage loop. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Preliminary information communicates an issue with a wind noise while driving at highway speeds and dealers are to inspect the body harness pass through for being full seated into the cowl. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue with the Body Control Module setting DTC: P0606 and turning on a Check Engine Lamp. Read More »
This technical bulletin informs the dealer to add foam to the base of the clips to correct the condition of Instrument Panel Trim Plate Applique Loose. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue with the Body Control Module setting DTC: P0606 and turning on a Check Engine Lamp. Read More »
This engineering information (EI) ends the need for gathering information from technicians in regards to the roof panel joint finish molding being detached and/or loose from the roof retaining clip. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing liftgate paint peeling or chipping at applique. Read More »
This technical bulletin provides a step by step procedure to replace the pressure releif valve due to Flutter Noise from Right Rear Corner of the Vehicle. Read More »
This technical bulletin provides repair information to correct a customer concern of the Rear Washer System Inoperative, or Boot to Washer Hose Disconnection and Possible Hose Leaking. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the roof panel joint finish molding being detached and/or loose from the ... Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue with the Body Control Module setting DTC: P0606 and turning on a Check Engine Lamp. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This informational bulletin provides information for dealers/technicians on visible gap at hem flange where front door skin wraps around and meets door shell. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to having assist step insert loose, falling off and/or warped. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to having assist step insert loose, falling off and/or warped. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary information communicates and issue with a rattle noise from the liftgate/liftglass and how to make adjustment to correct the noise. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to paint concerns with the front and/or rear fascias. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
Service Update Bulletin. On certain vehicles equipped with radio suppression equipment (RPO UN9), the body to chassis ground fasteners may be missing. Dealers are to add the missing fasteners. Read More »
This Preliminary information communicates to the dealer technician to replace the transmission valve body on 2019-2021 10 speed transmissions to correct DTCs P2812 and P2814 setting if Service Information does not lead to root case of ... Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This technical bulletin provides repair information to correct a customer concern of paint chipping or peeling on front fascia, at interface of front fender and fascia near headlamp. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This Preliminary information communicates a parts restriction is in place for the Body Control Module on 2020 Cadillac CT4, CT5, Chevrolet Corvette, Suburban, Tahoe and GMC Yukon. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This technical bulletin provides repair information to correct a customer concern of Assist Step Running Boards Inoperable and Not Functioning with Door Operation. Read More »
Customer Satisfaction program. Certain vehicles may have a condition in which the trailering label has zeroed out information on the label. Read More »
This Preliminary information communicates and issue where the drivers memory seat will not move to its full travel and dealers are to perform a SPS setup procedure to the K40D Drivers Seat Adjuster Memory Module. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to paint concerns with the front and/or rear fascias. Read More »
This Preliminary information communicates an issue with a service column lock message with DTC U3000 sym71,72 or 96 and engineering is working on a fix. Read More »
This Preliminary information communicates that some customers may comment on a rattle, flutter, flapping, and/or wind type noise from the front end caused by either the left or right front inner wheel well liner having excessive movement. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information for dealers/technicians on visible gap at hem flange where front door skin wraps around and meets door shell. Read More »
This service bulletin provides repair information to correct a customer concern of DTC B1038 SYM64 set in the BCM and Door Ajar Message on Driver Information Center (DIC). Read More »
This Preliminary information communicates and issue with a rattle noise from the liftgate/liftglass and how to make adjustment to correct the noise. Read More »
This Preliminary information communicates and issue with a rattle noise from the liftgate/liftglass and how to make adjustment to correct the noise. Read More »
This Preliminary information communicates and issue with a rattle noise from the liftgate/liftglass and how to make adjustment to correct the noise. Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This Preliminary information communicates and issue with a rattle noise from the liftgate/liftglass and how to make adjustment to correct the noise. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This technical bulletin provides repair information to correct a customer concern of Rear Access Open Message Illuminated in DIC when Liftgate is Closed. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the power liftgate inoperative. Read More »
This Preliminary information communicates and issue with the hands free liftgate feature being inoperative after the vehicle has been turned off for an extended time. Dealers are to reprogram the BCM to correct this concern. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards the power liftgate inoperative. Read More »
This technical bulletin provides repair information to correct a customer concern of Liftgate Unwanted Opening Due to Hands-Free Calibration Sensitivity. Read More »
This engineering information (EI) ends the need for gathering information from technicians in regards to the roof panel joint finish molding being detached and/or loose from the roof retaining clip. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This service bulletin provides repair information to correct a customer concern of DTC B1038 SYM64 set in the BCM and Door Ajar Message on Driver Information Center (DIC). Read More »
This technical bulletin provides repair information to correct a customer concern of rear seat (60 Percent) and/or (40 Percent) chucking movement, and noise is present at rear latch to striker. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Liftgate Ajar Lamp illuminated on Driver Information Center (DIC) with ... Read More »
This Preliminary information communicates an issue with a low or dead battery issue cause by the rear hvac door being jammed by an foreign object. Read More »
This Preliminary information communicates an issue with a low or dead battery issue cause by the rear hvac door being jammed by an foreign object. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
Customer Satisfaction Program (Revised Service Procedure). Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This technical bulletin provides repair information to correct a customer concern of Tire Pressure Monitor System Sensors Display Dashes with Trailer Connected. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary information communicates to technicians to advise dealership technicians to inspect the camshaft exciter wheel and replace it if necessary. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This service bulletin provides repair information to correct customer concerns of Rear Wheel Lock Up, ABS Event, Loud Bang and a Flashing ?D? on Driver Information Center (DIC) when Lightly or Moderately Accelerating Forcing an 8-7 or 8-6 ... Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This preliminary information bulletin instructs to technicians to use the Picoscope or a make physical inspection to check for debris on the cam postion sensor and to check for a bent target wheel on the camshaft. Read More »
This Preliminary information communicates that some customers may comment on a rattle, flutter, flapping, and/or wind type noise from the front end caused by either the left or right front inner wheel well liner having excessive movement. Read More »
This Preliminary information communicates that some customers may comment on a rattle, flutter, flapping, and/or wind type noise from the front end caused by either the left or right front inner wheel well liner having excessive movement. Read More »
This Preliminary information communicates that some customers may comment on a rattle, flutter, flapping, and/or wind type noise from the front end caused by either the left or right front inner wheel well liner having excessive movement. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup ... Read More »
This technical bulletin provides a procedure to correct the condition of Service Restraint System Message / Air Bag Warning MIL / DTC B14DC Set. Read More »
This technical bulletin provides repair information to correct a customer concern of rear seat (60 Percent) and/or (40 Percent) chucking movement, and noise is present at rear latch to striker. Read More »
Customer Satisfaction Program (Revised Service Procedure). Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (VINS re-opened, software updated). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary information communicates and issue where the drivers memory seat will not move to its full travel and dealers are to perform a SPS setup procedure to the K40D Drivers Seat Adjuster Memory Module. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
This Preliminary information communicates an issue with the 3rd Row Seat Headrest not returning to the upright position after cycling the seat and to install a headrest repair kit. Read More »
This Preliminary information communicates an issue with the 3rd Row Seat Headrest not returning to the upright position after cycling the seat and to install a headrest repair kit. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting caused by high resistance at the F106DA Driver's front seat inboard air bag connector. Read More »
This technical bulletin provides repair information to correct a customer concern of a sticky comfort adjuster handle release, seat tracks out of sync on left rear 40 % seat. Read More »
This Preliminary information communicates an issue with the 3rd Row Seat Headrest not returning to the upright position after cycling the seat and to install a headrest repair kit. Read More »
This Preliminary information communicates an issue with the 3rd Row Seat Headrest not returning to the upright position after cycling the seat and to install a headrest repair kit. Read More »
This Preliminary information communicates A diagnostic tip from root causing DTC: C1197 caused by a pinched air inlet hose to the suspension compressor air leveling system. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary information communicates to dealership technicians that if they receive a radio with the 2 stickers as noted above, the radio was remanufactured with missing components and will need to order another radio unit from the ... Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This Preliminary information communicates the proper component naming and labor operation codes for the air leveling system RPO F47and the Electronic Suspension Control System RPO Z95 Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This Preliminary information communicates an issue with a SES MIL on and DTC U0139 set in the ECM. Dealers are to cycle the power to the suspension control module to correct this issue. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary information communicates a tip when diagnosing an inoperative air leveling suspension system and to repair any loss of comm DTC's with the power window motors first. Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Dealers are to replace both the front air springs. Read More »
This Preliminary information communicates the proper component naming and labor operation codes for the air leveling system RPO F47and the Electronic Suspension Control System RPO Z95 Read More »
This Preliminary information communicates an issue with the air leveling suspension losing air pressure in very cold temperatures while sitting for several hours. Engineering is working on a fix. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This service bulletin provides repair information to correct a customer concern of Automatic Emergency Braking (AEB) Forward Collision Icon Lamp On with No DTCs Present. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to a Forward Collision Icon Message Illuminated on Driver Information Center (DIC) and/or No DTCs Set. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a Forward Collision Icon Message Illuminated on Driver Information Center (DIC) ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to having a No Start, Forward Collision Alert, Adaptive Cruise Control and/or ... Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
(There may be future updates under this same release number.) Your vehicle keeps getting better. This software update includes the following if your vehicle is equipped: Refinements: Updates made to improve the Super Cruise driver ... Read More »
This Preliminary information communicates an issue with adaptive cruise and lane keep assist inoperative due to an internal issue with the front view windshield camera. Dealers are to replace the camera. Read More »
This Preliminary information communicates an issue with adaptive cruise and lane keep assist inoperative due to an internal issue with the front view windshield camera. Dealers are to replace the camera. Read More »
(There may be future updates under this same release number.) Your vehicle keeps getting better. This software update includes the following if your vehicle is equipped: Refinements: Updates made to improve the Super Cruise driver ... Read More »
This Preliminary information communicates an issue with adaptive cruise and lane keep assist inoperative due to an internal issue with the front view windshield camera. Dealers are to replace the camera. Read More »
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Read More »
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Read More »
This Preliminary information communicates an issue with adaptive cruise and lane keep assist inoperative due to an internal issue with the front view windshield camera. Dealers are to replace the camera. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to one or more camera views showing intermittent behavior and/or totally ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to having a No Start, Forward Collision Alert, Adaptive Cruise Control and/or ... Read More »
Service Update. On certain vehicles the clamp may not be properly aligned and positioned on the hose, or the hose is rolled over on the pump port. The improper assembly can quickly develop into a significant leak early in the truck?s life. Read More »
This Preliminary information communicates an issue with adaptive cruise and lane keep assist inoperative due to an internal issue with the front view windshield camera. Dealers are to replace the camera. Read More »
This Preliminary information communicates an issue with adaptive cruise and lane keep assist inoperative due to an internal issue with the front view windshield camera. Dealers are to replace the camera. Read More »
This Preliminary information communicates an issue with a wind noise while driving at highway speeds and dealers are to inspect the body harness pass through for being full seated into the cowl. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary information communicates an issue with a wind noise while driving at highway speeds and dealers are to inspect the body harness pass through for being full seated into the cowl. Read More »
This Preliminary information communicates a diagnostic tip for a thump, click, pop, clunk type noise that is heard from the front end. Dealers are to inspect for something contacting the grill shutters as they open and close. Read More »
This Preliminary information communicates an issue with the GDS2 scan tool not being able to communication with the front view camera module and provides a work around until GDS2 is fixed. Read More »
This Preliminary information communicates and issue with unwanted content theft alarm going off for no reason and to reprogram the BCM to correct the issue. Read More »
This Preliminary information communicates an issue with the GDS2 scan tool not being able to communication with the front view camera module and provides a work around until GDS2 is fixed. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This preliminary information bulletin instructs to technicians to use the Picoscope or a make physical inspection to check for debris on the cam postion sensor and to check for a bent target wheel on the camshaft. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to one or more camera views showing intermittent behavior and/or totally ... Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This Preliminary information communicates that engineering is investigating a repair for a chirp noise associated with the front axle assembly. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506,P3189, P318A, P318B, P318C, P318D, P318E, P318F, P3190 Possible broken valve ... Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506,P3189, P318A, P318B, P318C, P318D, P318E, P318F, P3190 Possible broken valve ... Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards one or more camera views showing, intermittent behavior and/or totally ... Read More »
This Preliminary information communicates that some customers may comment on a rattle, flutter, flapping, and/or wind type noise from the front end caused by either the left or right front inner wheel well liner having excessive movement. Read More »
This Preliminary information communicates that some customers may comment on a rattle, flutter, flapping, and/or wind type noise from the front end caused by either the left or right front inner wheel well liner having excessive movement. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
This Preliminary information communicates to the technition instructions to replace the particulate matter sensor for a P1488 and to use the special labor operation for tracking purposes. Read More »
This Preliminary information communicates to the technition instructions to replace the particulate matter sensor for a P1488 and to use the special labor operation for tracking purposes. Read More »
This Preliminary information communicates and issue with programming a replacement side object detection module and engineering is working on the issue. Read More »
Service Update Bulletin - Certain 2021 model year Chevrolet Suburban, Tahoe, and GMC Yukon vehicles may have a kink in the rear camera washer hose. Read More »
This service bulletin provides repair information on release of Radio Software Version V160 Update to correct customer concerns of radio software issues. Read More »
Service Update - Certain 2021 vehicles have a condition where, if an over the air (OTA) update was sent to an affected vehicle, the update would fail. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Camera Display. Read More »
This Preliminary information communicates that a customer may notice that the gridlines on the backup camera are very dim. They may mention that this occurred after an OTA update. The dealer technician is advised to perform no repairs. Read More »
This Preliminary information communicates a condtion where SD card removed is being displayed on the radio display intermittently. ThisPI advises that engineering is working on a fix for this issue Read More »
This technical bulletin provides a procedure to replace the video player and reprogram to correct the condition of Non-Responsive Touch on Rear Seat Infotainment Left Screen . Read More »
This Preliminary information communicates a condition where the the customer may see a SD card remove message accompanied by a 0X40000 code on the DIC or radio display. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary information communicates an issue with an SIR MIL with DTC B14DC caused by the air bag connector contacting the foam in the drivers seat. Dealer to remove the foam that is contacting the air bag connector. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This Preliminary information communicates an issue with an OTA pending message still displayed after an OTA event and how to reset/clear the message. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This service bulletin provides information for dealers/technicians on MDI 2 Required When Programming Vehicles with Vehicle Intelligence Platform (VIP). Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This informational bulletin advises the technician to check for faults that may be caused by the trailer otherwise found by a possible faulty trailer connector. Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This service bulletin provides information for dealers/technicians on MDI 2 Required When Programming Vehicles with Vehicle Intelligence Platform (VIP). Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides a procedure to replace the front wheel drive shaft to correct a customer concern of a Squeak/Chirp Noise from Front Axle in 2wd. Read More »
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present ... Read More »
This service bulletin helps diagnose/reduce possible CCND issues on Transfer Cases - Service 4WD on DIC, Intermittent Failures, Noise Concerns, Driveline/Steering Vibration/Shudder, Intermittent DTCs/MIL Illuminated, ... Read More »
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
This engineering information (EI) closure ends the need for gathering further information from technicians in regard to a binding, moan and/or chatter type sound heard from the rear of the vehicle when making slow parking lot maneuvers. Read More »
This technical bulletin provides a procedure to program the Reductant Control Module and Setup and Perform the Reductant Fluid Tank Level Reset. Read More »
This technical bulletin provides a procedure to correct the condition of Accessory Roof Rack Cross Rail, Luggage Carrier Cross Rail Key Stuck in Lock, Lock Stuck or Inoperable. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This service bulletin provides repair information to correct a customer concern of Black Radio Display Screen (Triangle and Camera with Slash Through it) with DTCs B1A62 82 and 86 Setting Current in Video Processing Module (VPM). Read More »
This service bulletin provides repair information to correct a customer concern of Black Radio Display Screen (triangle and camera with the slash through it) with DTCs B1A62 82 and 86 setting current in Video Processing Module (VPM). Read More »
This Preliminary information communicates an issue during start up that the following symptoms occur: - Service Safety Restraints System Message - Sunroof Inoperative - Sunshade Lights Inoperative - Dome Lights Inoperative - Power ... Read More »
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships. Read More »
This technical bulletin has you remove flash and reinstall clip to correct condition of Arm Rest Does Not Lock in Position and Slides Back and Forth. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This technical bulletin informs the dealer to add foam to the base of the clips to correct the condition of Instrument Panel Trim Plate Applique Loose. Read More »
This technical bulletin provides repair information to correct a customer concern of Black Radio Display Screen (Triangle and Camera with Slash Through it) with DTCs B1A62 82 and 86 Setting Current in Video Processing Module (VPM). Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Camera Display. Read More »
This technical bulletin provides repair information to correct a customer concern of seeing liftgate paint peeling or chipping at applique. Read More »
This technical bulletin provides service information to correct a customer concern of HVAC Heat Intermittently Inoperative, DTCs B2B05 and/or B2B06 Set. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides information for dealers/technicians on MDI 2 Required When Programming Vehicles with Vehicle Intelligence Platform (VIP). Read More »
This service bulletin provides diagnostic/repair information to correct a customer concern of Cellphone not Charging or USB Receptacle Inoperative. Read More »
This technical bulletin provides repair information to correct a customer concern of the Rear Washer System Inoperative, or Boot to Washer Hose Disconnection and Possible Hose Leaking. Read More »
This service bulletin provides repair information on release of Radio Software Version V160 Update to correct customer concerns of radio software issues. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards on the rear washer hose being disconnected. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides information on Terms and Conditions/Privacy Statement App (TCPS App) Guide for infotainment systems in a default factory demo mode. Read More »
This service bulletin provides repair information on release of Radio Software Version V160 Update to correct customer concerns of radio software issues. Read More »
This service bulletin provides repair information on release of Radio Software Version V160 Update to correct customer concerns of radio software issues. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides service information/procedures on continuous improvement Radio Software Version V158 Update to address customer comments on software related issues. Read More »
This Preliminary information communicates information on vehicle speed being limited due to aftermarket lower kit being installed on the vehicle. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on the rear washer hose being disconnected. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This technical bulletin has you remove flash and reinstal clip to correct condition of Arm Rest Does Not Lock in Position and Slides Back and Forth. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This engineering information (EI) closure ends the need for further information from the field in regards to Power Floor Console Armrest will not lock in place and/or the console lid slides back and forth freely. Read More »
This service bulletin provides repair information to correct a customer concern of DTC B1038 SYM64 set in the BCM and Door Ajar Message on Driver Information Center (DIC). Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Power Floor Console Armrest will not lock in place and/or the console ... Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates to the dealer an issue where a vehicle may be exhibiting an engine noise condiion. The dealer is instructed on how to isolate the noise to a specific area of the engine for further diagnosis. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This Preliminary information communicates an issues with an SES MIL, A/C blowing warm air and DTC's B1AA3 U3018 U3505 due to Fuse F4DR open. Dealers are to inspect the wiring in the front floor console. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Rearview Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Rear View Camera Display. Read More »
This service bulletin provides repair information to correct a customer concern of Service Driver Assist and/or Take Steering Messages on Start-up, Advanced Driver Assist Systems (ADAS) Features Not Available with DTCs U1614, U1615, U1616 ... Read More »
This technical bulletin provides repair information to correct a customer concern of Power to the 110V/120 Outlet is Interrupted During an Auto Stop/Start Event. Read More »
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a No Fob detected message on Driver Information Center (DIC) and/or No Crank / No Start condition. Read More »
This Preliminary information communicates information on vehicle speed being limited due to aftermarket lower kit being installed on the vehicle. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary information communicates an issue with: Overhead Console Inoperative / Service Safety Restraints Message / Sunroof Inoperative / DTC's B1A7A and U1121. Read More »
Customer Satisfaction Program. On certain vehicles with a special service sales package and radio infotainment system (RPOs 5W4 and IOR), the left hand buttons on the backside of the steering wheel currently enable favorites instead of ... Read More »
This Preliminary information communicates that a vehicle may exhibit a misfire condition resulting in misfire codes P0300-P308. Upon diagnosis it may be discovered the lifter has come apart. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary information communicates an issue with the floor center console cooler being inoperative and engineering working on a root cause. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
This technical bulletin provides repair information to correct a customer concern of SUV Vehicle Software Configuration Management Update (VeSCoM). Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to concerns with the front center floor power console function and/or ... Read More »
This engineering information (EI) requests dealership personnel involve GM Engineering in the event an Owner is in Receipt of a PAI (Proactive Alert Identifier) "SAC003" and/or the Dealer is informed of excessive Parasitic Drains on an ... Read More »
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition. Read More »
Service Update - Certain 2021 model year Chevrolet Suburban, Tahoe, and GMC Yukon, Yukon XL vehicles may have been built with 3rd row head restraints that will not stay up after being folded forward, due to an internal spring tab breaking. Read More »
Service Update Bulletin. On certain vehicles equipped with radio suppression equipment (RPO UN9), the body to chassis ground fasteners may be missing. Dealers are to add the missing fasteners. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary information communicates to the dealer technician that the valve body Part Unique Number (PUN) may contain the letter O or the number 0. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary information communicates an issues with an SES MIL and DTC P2B87 setting. Engineering has releasing updated cals to correct the concern. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This technical bulletin provides repair information to correct a customer concern of Assist Step Running Boards Inoperable and Not Functioning with Door Operation. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This technical bulletin provides repair information to correct a customer concern of Possible Crank No Start or Extended Crank with DTC P12A6. Read More »
This Preliminary information communicates an issue with the floor center console cooler being inoperative and engineering working on a root cause. Read More »
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or Non-Responsive to Touch After Cleaning/Disinfecting Radio Display. Read More »
This Preliminary information communicates an issue with the floor center console cooler being inoperative and engineering working on a root cause. Read More »
Service Update. A small number of vehicles may have been built with a cracked steering gear ballnut which could result in noise and reduction of steering performance. Dealers are to replace the steering gear. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (VINS re-opened, software updated). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program. In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
Customer Satisfaction Program (Programming Suspended/Resumed) - Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern. Read More »
This Preliminary information communicates A Vehicle may have a concern of service engine light, misfire and engine noise with possible of DTC P0300 P0106 P0506, Possible valve spring concern Read More »
This Preliminary information communicates and issue with programming a replacement side object detection module and engineering is working on the issue. Read More »
Customer Satisfaction program. Certain vehicles may have a condition in which the trailering label has zeroed out information on the label. Read More »
This service bulletin provides repair information to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated with DTCs U1961, U1983 setting. Read More »
This Preliminary information communicates there is a Part Restriction for the Automatic Leveling Control Module and to contact the PQC to order the part. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards one or more camera views showing, intermittent behavior and/or totally ... Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
Customer Satisfaction Program - Certain vehicles may have a condition in which the brake system control module (BSCM) may set and latch an internal fault in the module?s on-board diagnostics (OBD) buffer. Read More »
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers. Read More »
This Preliminary information communicates and issue with customers misunderstanding weather they need to bluetooth pair the factory provided headphones. Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF. Read More »
This Preliminary information communicates and issue with a rattle noise from the liftgate/liftglass and how to make adjustment to correct the noise. Read More »
This Preliminary information communicates an issues with false codes setting in vehicles due to timing issues with modules Engineering is working on a fix Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This Preliminary information communicates an issue with a gurgle noise from the sunroof drains and advises customers to turn on the HVAC blower to clear the drain. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This informational bulletin provides information for dealers/technicians on the 2021 Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL New Model Features. Read More »
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the Engine Control Module. Read More »
This Preliminary information communicates and issue with the LED right above the wireless charging pad being inoperative and how to resolve the concern with the LED. Read More »
This Preliminary information communicates and issue with customers misunderstanding weather they need to bluetooth pair the factory provided headphones. Read More »
This Preliminary information communicates an issue where the vehicles wireless charger no longer works with certain ISO updates on Apple 15 phones and advises customer to update their phone to the lastest ISO update. Read More »
This Preliminary information communicates an issue where the vehicles wireless charger no longer works with the latest ISO update on Apple 15 phones. Read More »
This Preliminary information communicates an issue with an OTA pending message still displayed after an OTA event and how to reset/clear the message. Read More »
This service bulletin provides repair information on release of Radio Software Version V160 Update to correct customer concerns of radio software issues. Read More »
Service Update Bulletin. Certain vehicles that had the Serial Data Gateway Module (SDGM) replaced in service, may not have been programmed correctly resulting in an incomplete registration of the new module. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides information for dealers/technicians on Normal Characteristic - Wireless Phone Projection Audio Cuts Out Every 10 Seconds on New/Unsold Vehicles. Read More »
This Preliminary information communicates an issue with the 110 volt power outlets not resetting if overloaded and causing the customer to take the vehicle to the dealership to have it reset. Engineering is working on a new cal. Read More »
This Preliminary information communicates and issues with Fuse F49 blowing causing a SES MIL and a Service Theft Deterrent System message displayed in the DIC. Read More »
This service bulletin provides repair information to correct a customer concern of Black Radio Display Screen (triangle and camera with the slash through it) with DTCs B1A62 82 and 86 setting current in Video Processing Module (VPM). Read More »
This Preliminary information communicates a condtion where SD card removed is being displayed on the radio display intermittently. ThisPI advises that engineering is working on a fix for this issue Read More »
This Preliminary information communicates a condition where the the customer may see a SD card remove message accompanied by a 0X40000 code on the DIC or radio display. Read More »
Service Update - Certain 2021 vehicles have a condition where, if an over the air (OTA) update was sent to an affected vehicle, the update would fail. Read More »
This Preliminary information communicates a cocnern where a flashing spot can intermittently show up on the radio display while in reverse. The PI advises that engineering is investigating the concern. Read More »
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or Non-Responsive to Touch After Cleaning/Disinfecting Radio Display. Read More »
This Preliminary information communicates an issue where the vehicles wireless charger no longer works with the lastest ISO update on Apple 15 phones. Read More »
This service bulletin provides repair information to correct a customer concern of Black Radio Display Screen (triangle and camera with the slash through it) with DTCs B1A62 82 and 86 setting current in Video Processing Module (VPM). Read More »
This service bulletin provides information for customers/dealers/technicians on Normal Camera Display Operation - Flashing Diamond - Spot - or UFO like image on Camera Display. Read More »
This Preliminary information communicates an issue where the vehicles wireless charger no longer works with the lastest ISO update on Apple 15 phones. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
Service Update. Certain vehicles, equipped with an Infotainment System, may have a condition during cold temperature conditions where the Infotainment screen is blacked out. Dealers will reprogram the radio. Read More »
This service bulletin provides repair information to correct a customer concern of Black Radio Display Screen (Triangle and Camera with Slash Through it) with DTCs B1A62 82 and 86 Setting Current in Video Processing Module (VPM). Read More »
This Preliminary information communicates and issue with customers misunderstanding weather they need to bluetooth pair the factory provided headphones. Read More »
This Preliminary Information communication requests information from the technician about vehicles that may have Bluetooth or phone projection issues. Read More »
This Preliminary information communicates and issue with customers misunderstanding weather they need to bluetooth pair the factory provided headphones. Read More »
This Preliminary information communicates an issue where the vehicles wireless charger no longer works with the latest ISO update on Apple 15 phones. Read More »
This Preliminary information communicates an issue where the vehicles wireless charger no longer works with the lastest ISO update on Apple 15 phones. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin provides repair information to correct a customer concern of Power to the 110V/120 Outlet is Interrupted During an Auto Stop/Start Event. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. Read More »
This Preliminary information communicates an issue with poor heater performance and advises dealerships to inspect the heater core inlet and outlet hoses for being twisted or kinked. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Preliminary information communicates an issue with an OTA pending message still displayed after an OTA event and how to reset/clear the message. Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates an issues with the odometer being incorrect after a programming event and how the dealership can resolve the issue. Read More »
This Preliminary information communicates an issue with the 2nd row bucket seat having side to side movement. GM engineering is working on a fix. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary information communicates an issues will low or poor heater performance on the drivers side. Dealers are to inspect the HVAC temperature door linkage and if ok replace the heater core. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Service Update. Certain vehicles may present a broken engine valve spring. This may cause the engine to run rough, an engine knocking or ticking noise, a check engine light illumination, or a possible vehicle stall. Read More »
Customer Satisfaction Program (Revised Service Procedure and Part Ordering Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
Customer Satisfaction Program (Revised Correction, Service Procedure and Warranty Information). In certain vehicles, driver movement can disrupt the electrical connection to the seat-mounted inboard airbag system. Read More »
This Preliminary information communicates an issue with how to properly inspect and ensure the air lines for the air suspension system are fully seated. Read More »
This Preliminary information communicates an issue with a gurgle noise from the sunroof drains and advises customers to turn on the HVAC blower to clear the drain. Read More »
This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern. Read More »
This service bulletin provides repair information to correct a customer concern of a Malfunction Indicator Lamp (MIL) Illuminated with DTCs U1961, U1983 setting. Read More »
This Preliminary information communicates there is a Part Restriction for the Automatic Leveling Control Module and to contact the PQC to order the part. Read More »
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards one or more camera views showing, intermittent behavior and/or totally ... Read More »
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates and issue with a rattle noise from the liftgate/liftglass and how to make adjustment to correct the noise. Read More »
This Preliminary information communicates an issue with the SIR MIL turning on and DTC B14DC setting. Engineering is root causing the concern. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or Non-Responsive to Touch After Cleaning/Disinfecting Radio Display. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary information communicates a diagnostic tip on how to resolve a issue if the serial data authentication configuration did not complete correctly. Read More »
This technical bulletin provides repair information to correct a customer concern of a gurgle or sloshing noise heard coming from the front sunroof drain hose areas. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This technical bulletin provides a procedure to replace the fuel filter and perform a filter life procedure if found the reason for a failed fuel filter life reset during ECM transfer of data. Read More »
