Technical Service Bulletins (TSBs) for the 2019 Silverado 3500 are official communications between Chevrolet & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
This Preliminary information communicates information on a hydrauilc rush type noise from the power steering gear. This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary information communicates information on a hydrauilc rush type noise from the power steering gear. This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. Read More »
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
This technical bulletin provides repair information to correct a customer concern of Intermittent "Service Steering Column Lock" message displayed with U0155 Set. Read More »
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information ... Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that show a "Take Steering" message on the Driver Information Center along with a warning chime/alert. Read More »
This informational bulletin provides information for the customer to pair their phone in order for the push to talk button on the steering wheel control to work. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a Squeak, Grind or Clunking Noise from Rear Leaf Springs. Read More »
This service bulletin provides a repair procedure to correct a customer concern of a Squeak, Grind or Clunking Noise from Rear Leaf Springs. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of ... Read More »
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This Preliminary information communicates the possibility of dtc p06DD due to low or no oil pressure immediately following engine oil and filter change due to oil filter and main oil gallery being drained or empty. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition. Read More »
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with ... Read More »
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away. Read More »
This Preliminary information communicates to the dealer technician using the PICO scope will aid in determining if the if the engine or transmission is root cause of a vibration or shudder concern. Read More »
This Preliminary information communicates to the dealer technicians that the oil life monitoring system for 2019 Duramax 6.6 L5P is under investigation by engineering. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be ... Read More »
This informational bulletin provides information on High Oil Pressure during Initial Start of Vehicle is considered a normal characteristic and no repairs should be completed for this condition. Read More »
This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Read More »
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up on the glow plug causing a premature failure. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up on the glow plug causing a premature failure. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours. Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Oil Leaking from Front of Engine. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary information communicates the possibility of dtc p06DD due to low or no oil pressure immediately following engine oil and filter change due to oil filter and main oil gallery being drained or empty. Read More »
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
This Preliminary information communicates to the dealer an issue where a vehicle may be exhibiting an engine noise condiion. The dealer is instructed on how to isolate the noise to a specific area of the engine for further diagnosis. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours. Read More »
N192264210 - Customer Satisfaction Program - Certain vehicles may have a condition in which the block heater cable function was disabled. Dealers will replace the engine block heater and cord. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Read More »
This informational bulletin provides information on Perceived Longer Crank, Misfire, Hesitation Feel and/or Surge conditions of the new L5P 6.6L Diesel Engine. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Read More »
This Preliminary information communicates the location that dealers can find information to remove / delete the rear fuel tank from Chassis Cab trucks with RPO N2N dual fuel tanks. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This technical bulletin provides a procedure to test and replace the high pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
This Preliminary Information communication advises the technician that the 6.6L Duramax Diesel Regular Production Option Code L5D has been placed on Engine Exchange program. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on Perceived Longer Crank, Misfire, Hesitation Feel and/or Surge conditions of the new L5P 6.6L Diesel Engine. Read More »
18157 - Customer Satisfaction Program. Certain Low Cab Forward vehicles, equipped with diesel engines, may have a condition in which the Fuel Tank Sub Unit float arm in the rear-mounted fuel tank may become disconnected causing the fuel ... Read More »
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
18157 - Customer Satisfaction Program. Certain Low Cab Forward vehicles, equipped with diesel engines, may have a condition in which the Fuel Tank Sub Unit float arm in the rear-mounted fuel tank may become disconnected causing the fuel ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried to shift the t-case from 4lo to Hi gears while driving. Read More »
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
This technical bulletin provides repair information to correct a customer concern of Service 4WD Message illuminated on Driver Information Center (DIC), DTCs C118D, C119B and/or C119C set. Read More »
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv. Read More »
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option ... Read More »
This Preliminary information communicates to the dealer technician using the PICO scope will aid in determining if the if the engine or transmission is root cause of a vibration or shudder concern. Read More »
This Preliminary Information communication provides information to the technician that a whine noise heard from the automatic transmission fluid pan hear with the the key on and engine off, or for up to one minute after the vehicle has ... Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with ... Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have "Service 4 Wheel Drive" message on the Driver Information Center. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a Service 4WD message being visible on the driver information center (DIC). Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have a radio backlighting will stay on even after the ignition has been turned off and the key has been removed for several minutes, ... Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This technical bulletin provides a procedure to test and replace the high pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This technical bulletin provides a procedure to install 2 way tape to correct a condition of Trailering Connector Loose Within Rear Bumper. Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This technical bulletin provides repair information to correct a customer concern of Service 4WD Message illuminated on Driver Information Center (DIC), DTCs C118D, C119B and/or C119C set. Read More »
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery. Read More »
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary Information communication provides information to the technician to help converting vehicles to fleet key option Regular Production Option Code 6E2 or 6E8. Read More »
This Preliminary information communicates diagnostic tips when trying to root cause a SES MIL with DTC's B2B0D and B2B0E. Main cause is aftermarket electrical devices spliced into the ignition main fuses. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
This engineering information (EI) is requesting information from the field to perform the check list provided and contact the engineer in regards to Instrument Panel Cluster (IPC) Gages at Zero, Multiple Warning Lights On, No Chimes ... Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This technical provides a procedure to locate, disconnect and re-connect the TCM electrical connector if found the cause of the customers concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information ... Read More »
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a low voltage reading on the volt gauge during the first several minutes after a cold start. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This engineering informational bulletin is requesting information from the field to determine a root cause for a condition of Service Engine Soon (SES) Light On, DTCs P06C5, P06CC, P066A, P066C, P066E, P067A, P067C, P067E, P068C, P068E, ... Read More »
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Read More »
This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be ... Read More »
This Preliminary Information communication provides information to the technician about the Upfitters questions about installing aftermarket electrical accessories. Read More »
This engineering informational bulletin is requesting information from the filed on vehicles that have the condition of Trailer Electrical Not Working as Intended and/or Trailer Message Displayed. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery. Read More »
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
Customer Satisfaction Program - Certain vehicles may have a condition in which the electronic brake controlmodule is less likely to activate the optional integrated brake assist. Normal braking capability functions as intended. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection ... Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information to dealers advising certain Over the air updates and USB updates have been temporarily suspended. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have "Service 4 Wheel Drive" message on the Driver Information Center. Read More »
This informational bulletin provides information on Loss of Phone Pairing or Favorites, Last Setting of Volume, Station, App, and Audio Settings Change When Vehicle Shuts Down in Demo Mode and that this is considered a normal ... Read More »
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors. Read More »
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information ... Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
This technical bulletin provides a procedure to add washers on the lower column mounting bracket locations due to the shaft laying on the metal support at the bottom of the column. Read More »
N192211090 - Customer Satisfaction Program. Certain vehicles equipped with Body Color Grille (RPO TC7) and Cold Weather Provision Options (RPO V10), may have a condition in which customers are unable to install the winter grille cover ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with ... Read More »
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This warranty administration bulletin provides the information on General Motors Tire Warranty Policies and Procedures for Low Cab Forward Medium Duty Trucks (US Medium Duty Dealers Only). Read More »
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
The complete Communication ID is: RFI20210526_939-187 and was communicated to customers on May 26, 2021. The Communication ID field did not permit me to enter the complete Communication ID as it is in our internal system. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a vibration at highway speed. Technician will need to replace the wheel for a rolled lip of aluminum in the hub opening. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shudder, bounce, bucking from the rear of the truck while braking when towing a gooseneck or fifth wheel trailer. Read More »
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or click type noise while driving. Read More »
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or click type noise while driving. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: - Yellow - Blurry - Distorted - Image scrolling - Image with NO gridlines - Screen is blue with ... Read More »
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
This service bulletin provides information for dealers/technicians on Handsfree Apple Iphone Call Static conditions equipped with IOB Radio. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This Preliminary information communicates to the dealer an issue where a vehicle may be exhibiting an engine noise condiion. The dealer is instructed on how to isolate the noise to a specific area of the engine for further diagnosis. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This SKU is a Tire Hoist Assembly. The customer communication requested return of unsold inventory to inspect for the shape of the centerpiece of the tire hoist being round when it should be square. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary information communicates to the dealer technician using the PICO scope will aid in determining if the if the engine or transmission is root cause of a vibration or shudder concern. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Informational bulletin provides important instructions for contacting the Fleet Action Center for repair authorization prior to replacement of certain parts. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Shudder, bounce, bucking from the rear of the truck while braking when towing a gooseneck or fifth wheel trailer. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) ... Read More »
This informational bulletin provides information for the customer to pair their phone in order for the push to talk button on the steering wheel control to work. Read More »
This engineering informational bulletin is requesting information from the filed on vehicles that have the condition of Trailer Electrical Not Working as Intended and/or Trailer Message Displayed. Read More »
This Preliminary information communicates Content Theft Deterrent RPO UTJ is included and only available with Remote Vehicle Start RPO BTV. Read More »
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection ... Read More »
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a Service 4WD message being visible on the driver information center (DIC). Read More »
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This engineering informational bulletin is requesting information from the field to determine a root cause for a condition of Service Engine Soon (SES) Light On, DTCs P06C5, P06CC, P066A, P066C, P066E, P067A, P067C, P067E, P068C, P068E, ... Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
This Preliminary information communicates to the dealer technicians that the oil life monitoring system for 2019 Duramax 6.6 L5P is under investigation by engineering. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This engineering informational bulletin is requesting information from the filed on vehicles that have the condition of Trailer Electrical Not Working as Intended and/or Trailer Message Displayed. Read More »
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection ... Read More »
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently and that engineering is investigating. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
