Technical Service Bulletins (TSBs) for the 2010 Impala are official communications between Chevrolet & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a clunk or pop noise from the front when turning the steering wheel at a stop or low speeds. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a whine or growl noise coming from the power steering. Read More »
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section. Read More »
This preliminary informational bulletin provides information for Pop or Clunk Noise When Turning Steering Wheel at a Stop or Low Speeds Condition. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section. Read More »
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS." Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the ... Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the ... Read More »
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal. Read More »
This Preliminary Information communication provides information to the technician about replacing the front struts on a 2006 - 2011 Impala with Regular Production Option Code 9C1 or 9C3. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a clunk or pop noise from the front when turning the steering wheel at a stop or low speeds. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
This Preliminary Information communication provides information to the technician about replacing the front struts on a 2006 - 2011 Impala with Regular Production Option Code 9C1 or 9C3. Read More »
GM: 2006-2011 IMPALA. THERE IS A GROWL NOISE IN THE FRONT OF THE VEHICLE WHEN DRIVING 20-50MPH. THIS MAY BE CAUSED BY A LOSS OF PRELOAD ON THE WHEEL BEARINGS. *RM Read More »
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO DIAGNOSE AND REPAIR THE VEHICLE IF THE ABS LAMP IS ON WITH DIAGNOSTIC TROUBLE CODE C0035 C0040 OR UNWANTED TRACTION CONTROL ACTIVATION. Read More »
CHEVROLET/BUICK/PONTIAC: WHEN TURNING, TRACTION CONTROL SYSTEM (TCS) OR ANTI BRAKING SYSTEM LIGHT WILL ILLUMINATE. MODEL 2007-2015 IMPALA, GRAND PRIX, LACROSSE. *PE Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a spongy brake pedal after a hydraulic brake component was disconnected or replaced. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a spongy brake pedal after a hydraulic brake component was disconnected or replaced. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
GM: AFTER A HYDRAULIC REPLACEMENT OR REMOVAL IT IS TOUGH TO REMOVE ALL THE AIR FROM THE BRAKE SYSTEM. THIS IS DUE TO THE LOCATION OF THE BRAKE LINES. *RM UPDATED 3/12112. *PE UPDATED 4/9/13. *PE UPDATED 3/20/14. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a spongy brake pedal after a hydraulic brake component was disconnected or replaced. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a spongy brake pedal after a hydraulic brake component was disconnected or replaced. Read More »
GM: AFTER A HYDRAULIC REPLACEMENT OR REMOVAL IT IS TOUGH TO REMOVE ALL THE AIR FROM THE BRAKE SYSTEM. THIS IS DUE TO THE LOCATION OF THE BRAKE LINES. *RM UPDATED 3/12112. *PE UPDATED 4/9/13. *PE UPDATED 3/20/14. Read More »
This preliminary informational bulletin provides a revision of PI0785A to add the 2014 model year, include Encore model and update the Parts and Warranty Information. Read More »
This preliminary informational bulletin provides a revision of PI0785A to add the 2014 model year, include Encore model and update the Parts and Warranty Information. Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP
This Preliminary Information communication provides information to the technician about vehicles with a spongy brake pedal after a hydraulic brake component was disconnected or replaced. Read More »
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO DIAGNOSE AND REPAIR THE VEHICLE IF THE ABS LAMP IS ON WITH DIAGNOSTIC TROUBLE CODE C0035 C0040 OR UNWANTED TRACTION CONTROL ACTIVATION. Read More »
CHEVROLET/BUICK/PONTIAC: WHEN TURNING, TRACTION CONTROL SYSTEM (TCS) OR ANTI BRAKING SYSTEM LIGHT WILL ILLUMINATE. MODEL 2007-2015 IMPALA, GRAND PRIX, LACROSSE. *PE Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO DIAGNOSE AND REPAIR THE VEHICLE IF THE ABS LAMP IS ON WITH DIAGNOSTIC TROUBLE CODE C0035 C0040 OR UNWANTED TRACTION CONTROL ACTIVATION. Read More »
This Preliminary Information communication provides the technician with steps to diagnose and repair the vehicle if the ABS lamp is on with Diagnostic Trouble Code C0035 C0040 or unwanted traction control activation. Read More »
CHEVROLET/BUICK/PONTIAC: WHEN TURNING, TRACTION CONTROL SYSTEM (TCS) OR ANTI BRAKING SYSTEM LIGHT WILL ILLUMINATE. MODEL 2007-2015 IMPALA, GRAND PRIX, LACROSSE. *PE Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. Read More »
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period. Read More »
14636 - SPECIAL COVERAGE. SOME 2009 MODEL YEAR BUICK LACROSSE AND ALLURE VEHICLES AND 2009-2011 MODEL YEAR CHEVROLET IMPALA VEHICLES MAY HAVE A BROKEN SOLDER CONNECTION WITHIN THE ACCELERATOR PEDAL POSITION (APP) SENSOR. Read More »
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
BUICK/CHEVROLET/PONTIAC: WHEN MESSAGE REDUCED ENGINE POWER IS DISPLAYED, THE MALFUNCTION INDICATOR LAMP WILL ILLUMINATED DUE TO POSSIBLE CAUSE OF TP SENSOR 1 AND TP SENSOR 2 EXCEEDING CALIBRATED VALUE FOR 2 SECONDS OR MORE. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2A? or global diagnostic system 2 ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that after installing a reman High Value V6 engine it has rough running, idle surge, misfire on one or both banks of the engine concern. Read More »
BUICK/CHEVROLET/PONTIAC/SATURN: AFTER INSTALLING REMAN HVV6 ENGINE, WOULD BE CONCERN WITH ROUGH RUNNING OR MISFIRE ON ONE OR BOTH BANKS OF ENGINE OR IDLE SURGING. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT. Read More »
14582 - Special Coverage. On some 2008 model year (MY) Saturn Outlook; 2008-2009 MY Buick Allure, Chevrolet Equinox, Chevrolet Uplander, Pontiac G8, Pontiac Montana SV6, Pontiac Torrent, and Saturn VUE; 2008-2010 MY Hummer H3 and Pontiac ... Read More »
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. Read More »
This technical bulletin provides repair information for crankshaft balancer inspection/replacement to correct a customer concern of engine squealing type noise on start-up or vibration or intermittent loss of accessory drive. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. Read More »
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an oil leak from the front of the vehicle. Technician will need to remove the oil pan and check the mating surface for flatness. Read More »
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified. Read More »
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified. Read More »
This technical bulletin provides a procedure to replace the TP sensor cover if the TP sensor exceeds the calibrated value and to correct the customers concern of the MIL on and Reduce Power message on. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that after installing a reman High Value V6 engine it has rough running, idle surge, misfire on one or both banks of the engine concern. Read More »
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils. Read More »
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils. Read More »
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Read More »
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2 Read More »
PONTIAC/SATURN/BUICK/GMC/CHEVROLET/CADILLAC/HUMMER: VEHICLE START AND STALLS AFTER THEFT DETERRENT MODULE REPLACEMENT. MODEL YEARS 2006-2011. DOES NOT APPLY TO VEHICLES WITH KEYLESS ACCESS SYSTEM. Read More »
CHEVROLET: SES LIGHT ON AND/OR REDUCED ENGINE POWER ECM SETTING MULTIPLE DTC'S. PRIOR TO REPLACING EITHER THE APP (ACCELERATOR PEDAL POSITION) SENSOR OR THE ECM (ENGINE CONTROL MODULE) PLEASE CHECK THESE COMMON CAUSES OF CONCERN-CHECK ... Read More »
This informational bulletin explains a normal condition from changes in Exhaust Tone for Active Fuel Management Engines when in Three or Four Cylinder Mode Read More »
ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO TEST THE COOLING FAN CIRCUIT FOR RESISTANCE IN ORDER TO PREVENT THE FAN MOTORS FROM LOSING PERFORMANCE ON POLICE VEHICLES. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in Three or Four Cylinder Mode. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON CHANGES IN EXHAUST TONE FOR ACTIVE FUEL MANAGEMENT ENGINES WHEN IN THREE OR FOUR CYLINDER MODE. Read More »
This Preliminary Information communication advises the technician what to inspect if codes P0016 and/or P0017 are setting on a properly timed engine or a condition of the vehicle cranks but will not start. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
GENERAL MOTORS: ENGINEERING INFORMATION-CHEMICAL DAMAGE ON INNER SURFACES OF FUEL TANK. SOME CUSTOMERS MAY COMMENT ON POOR PERFORMANCE, DECREASED ACCELERATION AND/OR AN INOPERATIVE FUEL GAUGE. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty ... Read More »
This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification. Read More »
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar? 4G upgrade. Read More »
This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a whine or growl noise coming from the power steering. Read More »
This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage Effective with 2010 Model Year. Read More »
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2A? or global diagnostic system 2 ... Read More »
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case. Read More »
This technical bulletin provides a procedure on the replacement of the throttle position sensor cover for a concern of a malfunction indicator lamp, reduced power message and DTC P2135. Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of ... Read More »
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow?. Read More »
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified. Read More »
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow?. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
This Preliminary Information communication provides information to the technician about vehicles that have a knock, clunk, pop, creak, or snap noise from the front of the vehicle. Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar? Module Functionality After OnStar Module Replacement for Another Condition. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line. Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
This Preliminary Information communication provides information to the technician with a diagnostic tip for the OnStar back-up battery failure. Technician may find Diagnostic Trouble Code B1446 or B1447 and the OnStar LED is red. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions. Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC ... Read More »
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only). Read More »
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This technical bulletin provides a procedure to replace the TP sensor cover if the TP sensor exceeds the calibrated value and to correct the customers concern of the MIL on and Reduce Power message on. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This Preliminary Information communication provides information to the technician about vehicles with a spongy brake pedal after a hydraulic brake component was disconnected or replaced. Read More »
This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This preliminary informational bulletin provides information onUnexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry? Phone - Bluetooth? Issues Concern. Read More »
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission. Read More »
GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE ... Read More »
This informational bulletin provides information accessory power outlet and trailer lighting fuse replacement due to electrical systems that can be affected by devices that are plugged in by the customer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicle with ambient temperature reading high in the scan tool data. Read More »
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection ... Read More »
This Preliminary Information communication provides information to the technician with a diagnostic tip for the OnStar back-up battery failure. Technician may find Diagnostic Trouble Code B1446 or B1447 and the OnStar LED is red. Read More »
This Preliminary Information communication provides information to the technician that the theft deterrent will need to be synchronized if the Theft Deterrent Module and Engine Control Module are replaced at the same time or if during ... Read More »
This Preliminary Information communication provides information to the technician about the common architecture Body Control Module utilizing several fuses for power, and the labeling of the fuses, it is possible to overlook some fuses in ... Read More »
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service. Read More »
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules. Read More »
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules. Read More »
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the ... Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A LIST OF CORRECTIONS FOR MULTIPLE CONCERNS REGARDING UNEXPECTED LOSS OF RADIO AUDIO (RADIO GOES SILENT/NO SOUND) AND OTHER BLACKBERRY PHONE - BLUETOOTH ... Read More »
GM: J-35616-64B TERMINAL TEST PROBE AND REPLACEMENT TERMINAL. ALSO INCLUDED MODELS VERANO, REGAL, LACROSSE, CTS, SRX, VOLT, SONIC, MALIBU, IMPALA, EQUINOX, CRUZE, AVALANCHE, TAHOE SUBURBAN, SILVERADO, SIERRA, YUKON, AND TERRAIN FOR ... Read More »
CHEVROLET: ENGINE POWER IS REDUCED MESSAGE AND CHECK ENGINE LAMP ON WITH DTC P0841. THE CONCERN MAY BE INTERMITTENT. OTHER DTCS THAT MAY SET ARE P0532, P0522, P0452, P0335, P0106, P0101 AND P0068. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries. Read More »
This Preliminary Information communication provides information to the technician with a diagnostic tip for the OnStar back-up battery failure. Technician may find Diagnostic Trouble Code B1446 or B1447 and the OnStar LED is red. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY. Read More »
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but ... Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not Read More »
This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement. Read More »
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are ... Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information. Read More »
This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices causing multiple issues. Read More »
CHEVROLET: ENGINE POWER IS REDUCED MESSAGE AND CHECK ENGINE LAMP ON WITH DTC P0841. THE CONCERN MAY BE INTERMITTENT. OTHER DTCS THAT MAY SET ARE P0532, P0522, P0452, P0335, P0106, P0101 AND P0068. Read More »
ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS
GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Remote Keyless Entry and or Remote Vehicle Start has poor range. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? ... Read More »
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs) Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS ... Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER:SENSOR/SENDING UNIT
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use. Read More »
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. Read More »
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin provides information on OnStar? VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
This Preliminary Information communication provides information to the technician on the Heater-Vent-Air Conditioning operation during a remote start event. Read More »
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels. Read More »
This preliminary informational bulletin provides diagnostic and repair information to correct a customer concern in which certain vehicles equipped with Gen 7 and OnStar, a recent over-the-air service update may have caused the OnStar ... Read More »
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken ... Read More »
This Preliminary Information communication provides information to the technician about vehicle starts and stalls on the first initial start after the replacement of the Theft Deterrent Module. Read More »
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only). Read More »
This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491). Read More »
This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front ... Read More »
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This technical bulletin provides repair information for low beam headlamp bulb diagnosis/replacement to correct a customer concern that the low beam headlamp is inoperative. Read More »
GM: LOW BEAM HEADLAMP BULB DIAGNOSIS/ REPLACEMENT (INSPECT BULB AND CONNECTOR). DO NOT REPLACE THE ENTIRE HEADLAMP ASSEMBLY FOR THIS CONDITION. REPLACE THE BULB AND INSPECT THE CONNECTOR. *JS UPDATED 4/7/15. Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance. Read More »
This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not replace any glass for this reason. Read More »
This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Read More »
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT. Read More »
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. Read More »
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions. Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds Read More »
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the rear defogger stays on for longer than 20 minutes. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This technical bulletin provides a procedure to complete a terminal replacement or connector re connection to correct a condition of Diagnostic Information for Supplemental Inflatable Restraint (SIR) System, Intermittent AIR BAG ... Read More »
PASSENGER PRESENCE SYSTEM (PPS) MAY COMMAND PASSENGER AIRBAG INDICATOR AND SEAT BELT REMINDER ON WHEN ELECTRONIC DEVICES (COMPUTERS, MP3 PLAYERS, CELL PHONES, DIAGNOSTIC SCAN TOOL, ETC. Read More »
GM: THE FRONT PASSENGER AIRBAG INDICATOR MAY LIGHT WHEN ELECTRONICS ARE PLACED IN THE PASSENGER SEAT. THE ELECTRONICS CAUSE THE VEHICLE TO THINK THERE IS A PASSENGER SITTING IN THE SEAT. *RM UPDATED 6/24/11. Read More »
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices Read More »
AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION:STATUS INDICATOR LAMP/LIGHT
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button ... Read More »
This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front ... Read More »
PASSENGER PRESENCE SYSTEM (PPS) MAY COMMAND PASSENGER AIRBAG INDICATOR AND SEAT BELT REMINDER ON WHEN ELECTRONIC DEVICES (COMPUTERS, MP3 PLAYERS, CELL PHONES, DIAGNOSTIC SCAN TOOL, ETC. Read More »
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. Read More »
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button ... Read More »
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. Read More »
Seatbelt Pretensioner Harness Out of Position, Airbag Indicator Light ON, DTCs Set Some customers may comment that the vehicle airbag indicator light is on. Read More »
This Preliminary Information communication provides information to the technician about 2009-2011 Impala having Diagnostic Trouble Code B001A, B001B, B0015, or B0022 set in the Sensing and Diagnostic Module. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only). Read More »
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
CHEVROLET: WATER LEAKS INTO THE INTERIOR OF THE VEHICLE. WATER COULD SHOW UP IN VARIOUS LOCATIONS IN THE INTERIOR OF THE VEHICLE, EXPECIALLY IF THE SOURCE OF THE WATER LEAK IS IN THE ROOF PANEL AREA. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
CHEVROLET: WATER LEAKS INTO THE INTERIOR OF THE VEHICLE. WATER COULD SHOW UP IN VARIOUS LOCATIONS IN THE INTERIOR OF THE VEHICLE, EXPECIALLY IF THE SOURCE OF THE WATER LEAK IS IN THE ROOF PANEL AREA. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. Read More »
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. Read More »
CADILLAC/BUICK/CHEVROLET: ON SOME VEHICLES, DUE TO POSSIBLE FAULTY BRAKE PRESSURE SENSOR, CRUISE CONTROL FAILS TO ENGAGE OR STAY ENGAGED. *PE Read More »
14636 - SPECIAL COVERAGE. SOME 2009 MODEL YEAR BUICK LACROSSE AND ALLURE VEHICLES AND 2009-2011 MODEL YEAR CHEVROLET IMPALA VEHICLES MAY HAVE A BROKEN SOLDER CONNECTION WITHIN THE ACCELERATOR PEDAL POSITION (APP) SENSOR. Read More »
CHEVROLET/BUICK: SOME VEHICLES WILL OR MAY HAVE, WITHIN ACCELERATOR PEDAL POSITION SENSOR, A BROKEN SOLDER CONNECTION CAUSING REDUCTION IN ENGINE POWER AND TRACTION CONTROL ASSIST LOSS. MODEL 2009 LACROSSE, ALLURE, 2009-11 IMPALA. Read More »
CHEVROLET: SES LIGHT ON AND/OR REDUCED ENGINE POWER ECM SETTING MULTIPLE DTC'S. PRIOR TO REPLACING EITHER THE APP (ACCELERATOR PEDAL POSITION) SENSOR OR THE ECM (ENGINE CONTROL MODULE) PLEASE CHECK THESE COMMON CAUSES OF CONCERN-CHECK ... Read More »
VEHICLE SPEED CONTROL:THROTTLE:THROTTLE POSITION SENSOR (TPS)
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the ... Read More »
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty. Read More »
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on. Read More »
This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information. Read More »
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always be re-learned when accessory wheels are installed on the vehicle. Read More »
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires. Read More »
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with ... Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance. Read More »
This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance. Read More »
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes. Read More »
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip ... Read More »
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires. Read More »
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions. Read More »
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut. Read More »
This Preliminary Information communication provides the technician with steps to diagnose and repair the vehicle if the ABS lamp is on with Diagnostic Trouble Code C0035 C0040 or unwanted traction control activation. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted. Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
GM: 2006-2011 IMPALA. A CLUNK NOISE IS COMING FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING AND/OR WHEN PUTTING THE TRANSMISSION IN DRIVE OR REVERSE. THIS MAY BE CAUSED BY DAMAGED MOUNTING AREAS. Read More »
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This technical bulletin provides a procedure to repair and reposition the seat pretentioner wiring harness away from the seat frame to correct a possible short when the seat is in the full down position. Read More »
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have a heated seat cushion on the passenger's side is inoperative. Read More »
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
GM: A SERVICE STABILITRAK MESSAGE IS DISPLAYED. HIGH TEMPERATURES AND VIBRATION ARE CAUSING THE YAW SENSORS TO LOSE COMMUNICATION. 2010-2011 IMPALA. *RM Read More »
GM: A SERVICE STABILITRAK MESSAGE IS DISPLAYED. HIGH TEMPERATURES AND VIBRATION ARE CAUSING THE YAW SENSORS TO LOSE COMMUNICATION. 2010-2011 IMPALA. *RM Read More »
This information bulletin explains the use of drilling high strength steel in a collision repair and the GM recommended CryoCobalt Drill bit. Read More »
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern. The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. Read More »
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the ... Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in Three or Four Cylinder Mode. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim. Read More »
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program. Read More »
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs. Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester ... Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS ... Read More »
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the ... Read More »
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores. Read More »
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product ... Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder. Read More »
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications. Read More »
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only). Read More »
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only). Read More »
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles. Read More »
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar RemoteLink? phone application. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation. Read More »
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation. Read More »
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply. Read More »
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio may have one of these issues will not turn on and will only display the clock and all buttons on the radio are inoperative but ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This technical bulletin provides a procedure to replace the TP sensor cover if the TP sensor exceeds the calibrated value and to correct the customers concern of the MIL on and Reduce Power message on. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months). Read More »
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage Effective with 2010 Model Year. Read More »
This preliminary informational bulletin provides information onUnexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry? Phone - Bluetooth? Issues Concern. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the ... Read More »
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making. Read More »
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information. Read More »
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel. Read More »
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates. Read More »
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information. Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This informational bulletin provides a revision for 10-00-89-016 to include the 2012-2014 model years and update the Labor Operation graphic. Read More »
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information. Read More »
This preliminary informational bulletin provides a revision of PI0785A to add the 2014 model year, include Encore model and update the Parts and Warranty Information. Read More »
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission. Read More »
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is ... Read More »
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles Read More »
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only. Read More »
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service. Read More »
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service. Read More »
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service. Read More »
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules. Read More »
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules. Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS. Read More »
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After an OnStar In-Vehicle Voice Message Is Heard. Read More »
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Read More »
This technical bulletin provides a procedure to complete a terminal replacement or connector re connection to correct a condition of Diagnostic Information for Supplemental Inflatable Restraint (SIR) System, Intermittent AIR BAG ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near Read More »
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only) Read More »
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar? 4G upgrade. Read More »
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only). Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the OnStar LED is staying on after the vehicle Retained Accessory Power has turned off and/or their Bluetooth phone stays connected ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that the OnStar LED is staying on after the vehicle Retained Accessory Power has turned off and/or their Bluetooth phone stays connected ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to. Read More »
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound. Read More »
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound. Read More »
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have a heated seat cushion on the passenger's side is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have Remote Keyless Entry and or Remote Vehicle Start has poor range. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This preliminary informational bulletin provides a list of corrections for multiple concerns regarding Unexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry Phone - Bluetooth ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This Preliminary Information communication provides information to the technician that the theft deterrent will need to be synchronized if the Theft Deterrent Module and Engine Control Module are replaced at the same time or if during ... Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Read More »
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that ... Read More »
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS. Read More »
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR? TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO ... Read More »
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs) Read More »
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Read More »
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the radio may have one of these issues will not turn on and will only display the clock and all buttons on the radio are inoperative but ... Read More »
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Read More »
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels. Read More »
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Read More »
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Read More »
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound. Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A LIST OF CORRECTIONS FOR MULTIPLE CONCERNS REGARDING UNEXPECTED LOSS OF RADIO AUDIO (RADIO GOES SILENT/NO SOUND) AND OTHER BLACKBERRY PHONE - BLUETOOTH ... Read More »
This preliminary informational bulletin provides a list of corrections for multiple concerns regarding Unexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry Phone - Bluetooth ... Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Read More »
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
"THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR? TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO ... Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. Read More »
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only) Read More »
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during ... Read More »
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats ... Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months). Read More »
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only. Read More »
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT GENERAL MOTORS AND GENERAL MOTORS OF CANADA COMPANY DO NOT SUPPORT CROSS BORDER SALES. Read More »
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY. Read More »
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GM?S POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA. Read More »
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. Read More »
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores Read More »
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not. Read More »
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near Read More »
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only) Read More »
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Read More »
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada). Read More »
This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification. Read More »
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada). Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Read More »
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information. Read More »
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage. Read More »
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement. Read More »
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only). Read More »
This Preliminary Information communication advises the technician what to inspect if codes P0016 and/or P0017 are setting on a properly timed engine or a condition of the vehicle cranks but will not start. Read More »
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS). Read More »
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only). Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles. Read More »
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all ... Read More »
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair. Read More »
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary. Read More »
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months). Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS). Read More »
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, ... Read More »
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm. Read More »
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them. Read More »
This technical bulletin provides a procedure on the replacement of the throttle position sensor cover for a concern of a malfunction indicator lamp, reduced power message and DTC P2135. Read More »
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Read More »
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist ... Read More »
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty ... Read More »
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules. Read More »
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices. Read More »
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Read More »
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder ... Read More »
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty. Read More »
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done. Read More »
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only) Read More »
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only) Read More »
This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange Read More »
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks Read More »
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the ... Read More »
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only). Read More »
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 ... Read More »
This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable. Read More »
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 - Suspected Tampering or Vehicle Modifications. Read More »
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only). Read More »
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only). Read More »
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases. Read More »
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2. Read More »
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause ... Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months). Read More »
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them. Read More »
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application. Read More »
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules. Read More »
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Read More »
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels. Read More »
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm Read More »
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM. Read More »
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This Preliminary Information communication provides information to the technician on the Heater-Vent-Air Conditioning operation during a remote start event. Read More »
This Preliminary Information communication provides information to the technician about vehicles that may have musty odor from the heating, ventilation and air conditioning system. Read More »
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions. Read More »
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system. Read More »
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system. Read More »
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. Read More »
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. Read More »
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
