Technical Service Bulletins (TSBs) for the 2019 X7 are official communications between BMW & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
At low outside temperatures (below 40 degrees F) and slow driving speeds (i.e. when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned. Read More »
SITUATION Unusual noises occur only when operating the steering column in the axial direction. 1. A one-time thump sound at the start of movement Shortly after the steering column starts moving, retracting, or extending, a one-time ... Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
The steering intervention for Lane Departure Warning (LDW) is too strong (severe), which can create an uncomfortable feeling for the driver. Read More »
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle maynot start when placing the key against the steering column. Read More »
REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
FAILURE OF THE ELECTRIC STEERING COLUMN ADJUSTMENT AT HIGHER CABIN TEMPERATURE: Electric steering column adjustment fails when interior cabin temperatures rise above 122 degrees F (e.g., parked outdoors on hot day). Read More »
LANE DEPARTURE WARNING: STEERING WHEEL VIBRATION INSUFFICIENT. Lane Departure Warning (LDW) vibration of the steering wheel is not sufficient (too weak). Vibration actuator software. Read More »
REMOTE CONTROL IS NOT DETECTED. Vehicle cannot be opened or closed using comfort access engine start is not possible and the vehicle may not start when placing the key again in the steering column. Read More »
LANE DEPARTURE WARNING: STEERING INTERVENTION TOO STRONG. The steering intervention for Lane Departure Warning (LDW) is too strong (severe) which can create an uncomfortable feeling for the driver. Read More »
CHECKING IF REQUIRED REPLACING REAR RIDE HEIGHT SENSOR CONTROL RODS. The holders of both control rods for the ride height sensors on the rear axle may have been mounted incorrectly (the locking tabs are not correctly locked). Read More »
Service Information May 2019 Special Suspension Systems B37 01 19 Technical Service CHECK CONTROL MESSAGE (CCM) DRIVING COMFORT RESTRICTED. Chassis stabilization warning and CCM Driving comfort restricted. Read More »
Symptom 1: There are traces of coolant leaking under the vehicle, or there is significant pressure released along with coolant loss when opening the low temperature cooling system reservoir (engine cold). Read More »
INCORRECT CONDITION BASED SERVICE DATA FOR BRAKE FLUID SERVICE. "Brake fluid service due since 12/2001" is displayed in the instrument cluster although the vehicle is only a maximum of 1 year old. Read More »
IB BRAKE-BY-WIRE SYSTEM - PREFLIGHT CHECK. When starting a vehicle or driving off customers may complain of "no brake assist" or "hard brake pedal". Read More »
NO BRAKING FORCE ASSISTANCE AFTER ENGINE START DIAGNOSTIC TROUBLE CODE (DTC) 480705 / 480706. When starting the vehicle. The red brake warning light lights up in the instrument cluster. Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving. Read More »
COOLANT LINE QUICK DISCONNECTS LEAK IN LOW TEMPERATURES AT OR BELOW -15E?C (5E?F): The coolant reservoir in the high or low temperature cooling system is low There may be a coolant leak under the vehicle There may be a check control ... Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
NO BRAKING FORCE ASSISTANCE AFTER ENGINE START DIAGNOSTIC TROUBLE CODE (DTC) 4808B4. When starting the vehicle with Electric Park Brake (EPB) engaged. The brake pedal is hard. The red brake warning light in the instrument cluster lights up. Read More »
SERVICE BRAKES, HYDRAULIC:BRAKE FLUID LOW WARNING: LAMP
IB BRAKE-BY-WIRE SYSTEM - PREFLIGHT CHECK. When starting a vehicle or driving off customers may complain of "no brake assist" or "hard brake pedal". Read More »
When starting the vehicle vehicle at standstill, various yellow Check Control Messages CCMs appear. ID code 00042: Brake system. Additional notes: Avoid abrupt braking as far as possible. Drive at a moderate speed. Read More »
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Read More »
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
The customer may complain of a check control message stating "Safe share detected" (CCM-ID 953). Check control message can be verified by checking key reader information or performing the Check control message history service function. Read More »
REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine. Read More »
REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
COOLANT LEAK FROM LOW TEMPERATURE COOLING CIRCUIT (N63R): Coolant leaking from the engine compartment. Traces of coolant leaking from the expansion tank of the low temperature cooling system. Read More »
DELIVERY STOP - INSPECT NUTS ON CATALYTIC CONVERTER: BMW AG has issued a Delivery Stop (effective June 23, 2020) on certain Model Year 2020 BMW vehicles that were produced between March 10, 2020 and June 1, 2020. Read More »
B58C AND B58M ENGINES ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil ... Read More »
WIND NOISE FROM ENGINE BULKHEAD: A wind noise can be heard when driving at highway speeds from the area around the lower windshield. Improper sealing of the engine bulkhead trim. Read More »
Delivery Stop on certain Model Year 2019 and 2020 BMW vehicles that were produced between July 20 2018 and November 2 2019. There is a possibility of contamination in the engine. Read More »
SERVICE ACTION: BODY DOMAIN CONTROLLER PROGRAMMING: When the vehicle is left unlocked the interior light switch is continuously monitored. This may lead to an increased battery draw. Read More »
REMOTE CONTROL IS NOT DETECTED. Vehicle cannot be opened or closed using comfort access engine start is not possible and the vehicle may not start when placing the key again in the steering column. Read More »
CHECK ENGINE OIL LEVEL MESSAGE. "Check engine oil level" Check Control message (ID961) appears when starting the engine and again at the end of a trip. Read More »
DME FAULT MEMORY ENTRY FOR THE CRANKSHAFT SENSOR. Technicians may notice this fault logged during a diagnostic session Fault code Control module Fault Text 160021 DME Crankshaft sensor general loss of synchronism Environmental ... Read More »
Check Control message (CCM) indicates: (ID 213): Stop, exercising due care. Voltage supply The Service Engine Soon light is on with the following DME Fault Code: 21B209 - Starter alternator / belt for 48V system (OSA_RIEMEN_RISS): Belt ... Read More »
The Check Control message below appears even though the coolant level is not below minimum when theengine is cold. Check Control message (ID 166): Top up coolant. Read More »
Check Control message (CCM) indicates: (ID 213): Stop, exercising due care. Voltage supply The Service Engine Soon light is on with the following DME Fault Code: 21B209 - Starter alternator / belt for 48V system (OSA_RIEMEN_RISS): Belt ... Read More »
DSCi units which potentially have a faulty hydraulic valve were installed in the vehicles. The affected units may activate a sporadic red-colored Check Control Message. Read More »
BMW AG has issued a Delivery Stop (effective December 21, 2022) on a small number of Model Year 2023BMW X7 SAV vehicles that were produced between September 1, 2022 and December 3, 2022. Read More »
Symptom 1: There are traces of coolant leaking under the vehicle, or there is significant pressure released along with coolant loss when opening the low temperature cooling system reservoir (engine cold). Read More »
Mist formation on the windshield inside surface may occur at departure or after MSA (automaticstart/stop). Acoustic abnormality in the area of the recirculated air flap (recirculation flap closing and opening severaltimes). Read More »
The Check Control message below appears even though the coolant level is not below minimum when the engine is cold. Check Control message (ID 166): Top up coolant. Read More »
KIDNEY GRILL ACTIVE AIR FLAP FAULTS: A check control message or MIL (Malfunction Indicator Lamp) may be illuminated, with one or more of the following faults stored: 138207- Active cooling damper control (AKKS), top: blockage at warm ... Read More »
COOLANT LEAK FROM LOW TEMPERATURE COOLING CIRCUIT (N63R): Coolant leaking from the engine compartment. Traces of coolant leaking from the expansion tank of the low temperature cooling system. Read More »
TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. Read More »
SERVICE ACTION - ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection. Read More »
COOLANT LINE QUICK DISCONNECTS LEAK IN LOW TEMPERATURES AT OR BELOW -15E?C (5E?F): The coolant reservoir in the high or low temperature cooling system is low There may be a coolant leak under the vehicle There may be a check control ... Read More »
COOLANT LEAKING FROM THE LOW TEMPERATURE COOLING SYSTEM (B58C ENGINE): This Service Information Bulletin (Revision 1) replaces SI B17 02 20 dated March 2020. Read More »
COOLANT LEAK FROM LOW TEMPERATURE COOLING CIRCUIT (N63R): This Service Information Bulletin (Revision 5) replaces SI B17 06 17 dated June 2019. Traces of coolant leaking from the expansion tank of the low temperature cooling system. Read More »
Headlight Malfunction Check Control Message: Intermittently a check control message may be present stating "Adaptive headlight failure" (CC message 127) or "Headlight range control failure" (CC message 100). Read More »
ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: This Service Information Bulletin (Revision 1) replaces SI B11 01 20 dated February 2020. Read More »
SERVICE ACTION: ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection. Read More »
MALFUNCTION INDICATOR LAMP IS ILLUMINATED WITH A CRANKSHAFT ADAPTION FAULT: When diagnosing an illuminated malfunction indicator lamp (MIL) and/or a different issue the following faults may also be stored in the Digital Motor Electronics ... Read More »
SERVICE ACTION: ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection. Read More »
THE MIL MAY BE ILLUMINATED BY ERRONEOUS VALVETRONIC FAULTS. One of the following faults may be stored in the digital motor electronics (DME) either as part of diagnosing a different issue; and-or an illuminated malfunction indicator lamp ... Read More »
COOLANT LEAK FROM LOW TEMPERATURE COOLING CIRCUIT (N63R): Coolant leaking from the engine compartment. Traces of coolant leaking from the expansion tank of the low temperature cooling system. Read More »
DELIVERY STOP: PROGRAM CONTROL UNITS (DME). A Delivery Stop has been issued (effective May 16 2019) on certain Model Year 2016-2020 BMW vehicles that have been produced between June 19 2015 and April 17 2019. Read More »
SERVICE ACTION: N63M ENGINES - CHECK AND REPLACE THE FRESH AIR INTAKE DUCT. The incorrect crankcase ventilation non return valves may have been installed in the vehicle. Read More »
SERVICE ACTION: N63M ENGINES - CHECK AND REPLACE THE FRESH AIR INTAKE DUCT. The incorrect crankcase ventilation non return valves may have been installed in the vehicle. Read More »
On rare occasions during an engine oil service, the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE
DELIVERY STOP - INSPECT NUTS ON CATALYTIC CONVERTER: BMW AG has issued a Delivery Stop (effective June 23, 2020) on certain Model Year 2020 BMW vehicles that were produced between March 10, 2020 and June 1, 2020. Read More »
A vehicle arrives at your center to be diagnosed for a micro-leak in the fuel evaporative (EVAP) system(NVLD natural vacuum leak detection). Read More »
A vehicle arrives at your center to be diagnosed for a micro-leak in the fuel evaporative (EVAP) system (NVLD natural vacuum leak detection). Read More »
Symptom 1: There are traces of coolant leaking under the vehicle, or there is significant pressure released along with coolant loss when opening the low temperature cooling system reservoir (engine cold). Read More »
COOLANT LINE QUICK DISCONNECTS LEAK IN LOW TEMPERATURES AT OR BELOW -15E?C (5E?F): The coolant reservoir in the high or low temperature cooling system is low There may be a coolant leak under the vehicle There may be a check control ... Read More »
COOLANT LEAK FROM LOW TEMPERATURE COOLING CIRCUIT (N63R): This Service Information Bulletin (Revision 5) replaces SI B17 06 17 dated June 2019. Traces of coolant leaking from the expansion tank of the low temperature cooling system. Read More »
FUEL FILLER DOOR STICKING: The fuel filler door may be sticking requiring multiple attempts to open. The fuel filler door material can swell in wet conditions causing the filler door to stick. Read More »
CC MESSAGE THAT FUEL TANK IS EMPTY AND RANGE IS ZERO WHILE THERE IS STILL FUEL: The customer states that sporadically the vehicle's remaining drive range is displayed as 0 miles even though the fuel level indicator (aka gas gauge) still ... Read More »
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP
i>?FUEL FILLER DOOR WILL NOT OPEN: The fuel filler door (aka flap) will not open. In rare cases, if the vehicle is locked using the remote control key and the fuel filler door is pushed closed simultaneously, the fuel door can enter a ... Read More »
CC MESSAGE THAT FUEL TANK IS EMPTY AND RANGE IS ZERO WHILE THERE IS STILL FUEL: The customer states that sporadically the vehicle's remaining drive range is displayed as 0 miles even though the fuel level indicator (aka gas gauge) still ... Read More »
FUEL SYSTEM, OTHER:PNEUMATIC:DELIVERY:PIPES, HOSES, AND FITTINGS
BMW AG has issued a Delivery Stop: Due to a software failure, there is the possibility that the transmission does not go into "sleep mode" if the car is turned off. Read More »
After an automatic engine start (MSA start), the transmission intermittently goes into the Park "P" or Neutral "N" position without any customer influence. Read More »
ACCESSORIES DO NOT POWER UP FROM THE FRONT 12 V POWER SOCKET PLUG: Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
TRANSMISSION INTERMITTENTLY GOES INTO P OR N AFTER MSA ENGINE START. After an automatic engine start (MSA start) the transmission intermittently goes into the Park "P" or Neutral "N" position without any customer influence. Read More »
POWER TRAIN:MANUAL TRANSMISSION:SHIFT PATTERN INDICATOR
REARVIEW CAMERA: SPORADICALLY NO IMAGE IS DISPLAYED: This Service Information Bulletin (Revision 2) replaces SI B66 31 19 dated February 2020. Read More »
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. Read More »
The Central Information Display goes black intermittently due to resets of the Head Unit (HU-H3). FaultB7F8F9 ??A???A???A???A???A???A? ??A???A???A???A???A???A?HU-H: Reset??A???A???A???A???A???A? will be stored in the HU-H3. Read More »
When using the Key Reader to retrieve CBS information from the customer key, no current vehicle data is available, or the data does not match the maintenance schedule. Read More »
When using the Key Reader to retrieve CBS information from the customer key, no current vehicle data is available, or the data does not match the maintenance schedule. Read More »
Headlight check control (CC) message 128 "High beam headlight failure" is displayed. The following fault codes are stored during a vehicle test: 80419A - Left high-beam headlight: Short circuit and/or 8041A5 - light outputs: Number of ... Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
Due to a software error, the vehicle sporadically does not achieve sleep mode. As a result, the 12-volt battery becomes discharged and may cause a no-start condition. Read More »
BMW AG has issued a Delivery Stop (effective October 15, 2021) on certain Model Year 2022 BMW vehicles that were produced between September 28, 2021 and October 8, 2021. The issue involves the Active Crash Safety Module (ACSM) sensor. Read More »
"After programming to I-level 23-03-5xx, the fault memory 0x022270 is stored in the mPAD (Medium Platform Automatic Driving) and cannot be deleted. Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
Due to a software error, the vehicle sporadically does not achieve sleep mode. As a result, the 12-volt battery becomes discharged and may cause a no-start condition. Read More »
The gear selector switch (GWS) consists of the control electronics circuit and the selector lever. The sensors for recording the gearshift lever position and for inhibiting inadvertent gearshifts are integrated in the control electronics. Read More »
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. Read More »
Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained. Read More »
Due to component-related supply issues, the central information displays (CID) in some of the Model Year 2022 vehicles listed above were produced without the integrated touch screen function. Read More »
BMW AG has issued a Delivery Stop (effective October 25, 2021) on certain Model Year 2022 BMW vehicles that were produced after October 25, 2021. Read More »
Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained. Read More »
The incorrect Bluetooth module was installed in the headunit. Bluetooth functionality cannot be guaranteed, and mobile phones may possibly not be paired via Bluetooth. Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained. Read More »
Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained. Read More »
Driver Assistance reduced checked control message (CCM) appears. All or some of the system functions maybe inoperative. The following fault will be stored: 481CC6. Read More »
The incorrect Bluetooth module was installed in the headunit. Bluetooth functionality cannot be guaranteed, and mobile phones may possibly not be paired via Bluetooth. Read More »
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. Read More »
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. Read More »
On these Plug-in Hybrid Electric Vehicles (PHEV), the air conditioning cycles from cold to warm air while driving or while at a standstill. Read More »
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
While using the wireless charger, one or both of the following may occur: 1) The BMW display key or mobile phone becomes hot to the touch. 2) The device switches off due to over temperature (built-in device protection). Read More »
Customer states the following about their vehicle: active radio or music source is interrupted, the navigation is no longer available, a black screen is shown in the Control Display, the system works again after a short interruption. Read More »
BMW AG has issued a Delivery Stop (effective October 15, 2021) on certain Model Year 2022 BMW vehicles that were produced between September 28, 2021 and October 8, 2021. The issue involves the Active Crash Safety Module (ACSM) sensor. Read More »
BMW of North America (BMW NA) has made information available online to customers about software versions, including any changes to vehicle functionality that will result from each update. Read More »
The air conditioning cycles from cold to warm air while driving or while at a stand still. The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38F to 60F +) without changing any climate control settings. Read More »
48 V battery may become totally discharged, and possible replacement needed if: a) The vehicle has been charged using a 12 V charger with the hood closed during a long stationary period, the. For example, the showroom or storage. Read More »
HU-H3 MGU RESETS DUE TO BLUETOOTH CONNECTION WITH SAMSUNG ANDROID 11 : The head unit resets when using various apps (e.g., YouTube, Spotify, etc) on the connected mobile phone. This affects Samsung mobile phones (e.g. Read More »
ACCESSORIES DO NOT POWER UP FROM THE FRONT 12 V POWER SOCKET PLUG: Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Read More »
VOLT BATTERY MAINTENANCE: 48 V battery may become totally discharged, and possible replacement needed if: a) The vehicle has been charged using a 12 V charger with the hood closed during a long stationary period. Read More »
REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine. Read More »
CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident, the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
FALSE ALARM ACTIVATION TRIGGERED BY INTERIOR ULTRASOUND SENSOR: The DWA (anti-theft alarm) triggers for no apparent reason with all the vehicle's doors and windows closed. Read More »
BMW REMOTE SOFTWARE UPGRADE IS NOT OFFERED FOR INSTALLATION: The customer complaints that the BMW Remote Software Upgrade (RSU) is not possible in their vehicle, though the Remote Software Upgrade menu is available in the vehicle and a ... Read More »
REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine. A manufacturing defect affecting the ignition coil insulation. Read More »
WHEN LOCKING VEHICLE, DOORS ARE LOCKED BUT VEHICLE IS NOT SECURED: The customer complains that when locking the vehicle from the outside using the remote control: The doors lock The alarm system is not activated The side mirrors (when ... Read More »
MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED WITH FAULT MEMORY CDC152: The malfunction indicator lamp (MIL) is illuminated in the instrument cluster. The vehicles has no operating failures; only the MIL is illuminated. Read More »
?NO PREVIEW IMAGES DISPLAYED IN THE REAR SEAT ENTERTAINMENT: The rear seat entertainment screens do not display any preview images at times. Read More »
REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
WHEN LOCKING VEHICLE, DOORS ARE LOCKED BUT VEHICLE IS NOT SECURED: The customer complains that when locking the vehicle from the outside using the remote control: The doors lock. The alarm system is not activated. Read More »
CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident, the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
ACCESSORIES DO NOT POWER ON: Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Read More »
ACCESSORIES DO NOT POWER ON: Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Read More »
SERVICE ACTION - CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident, the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
NEW ECU VALIDATION NEEDED AFTER REPLACING CERTAIN CONTROL MODULES: With introduction of the new Headunit HU-H3 (MGU Media Graphics Unit), there is a new protection mechanism against tampering. Read More »
REMOTE SOFTWARE UPGRADE: For BMW, Remote Software Upgrade (RSU) is the next consequent step with regard to digitalization and customer satisfaction. With the introduction of RSU, customers now can update the vehicle software by themselves. Read More »
ACCESSORIES DO NOT POWER ON: Customer is not able to power accessories using the 12 volt power socket. Design change to reduce short circuits and blown fuses. Read More »
HEAD UNIT RESETS WHEN NAVIGATION IS USED IN CERTAIN LOCATIONS: The head unit resets sporadically causing the CID to turn black and then starts up again after a short time with the message "Start navigation system". Read More »
REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
DELIVERY STOP - CHECK STARTER BOLT: BMW AG has issued a Delivery Stop (effective July 30, 2020) on a small number of Model Year 2020 BMW vehicles that were produced on July 10, 2020. Read More »
COOLANT LINE QUICK DISCONNECTS LEAK IN LOW TEMPERATURES AT OR BELOW -15E?C (5E?F): The coolant reservoir in the high or low temperature cooling system is low There may be a coolant leak under the vehicle There may be a check control ... Read More »
SURROUND VIEW WRONG VEHICLE DISPLAYED AFTER PROGRAMMING: After programming the wrong vehicle model is displayed in the Central Information Display (CID) when the Surround View is activated. Read More »
DAYTIME RUNNING LIGHT IS DIM OR DISCOLORED: This Service Information Bulletin (Revision 2) replaces SI B63 04 18 dated January 2019. One or more of the LED daytime running lights are dim or discolored. Read More »
DISPLAYS SPORADICALLY REACT VERY SLOWLY WHEN SCROLLING IN THE AUDIO MENU: Sporadically the reaction time of the display in the instrument cluster the head-up display or in the CID (Central Information Display) is very long. Read More »
DIAGNOSTIC HINT: DRIVING ASSISTANCE SUPPORT REDUCED CHECK CONTROL MESSAGE DISP: Driving Assistance support reduced Check Control Message (CCM) is displayed sporadically. All or some of the system functions maybe inoperative. Read More »
REARVIEW CAMERA: SPORADICALLY NO IMAGE IS DISPLAYED: This Service Information Bulletin (Revision 2) replaces SI B66 31 19 dated February 2020. Read More »
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. Read More »
SERVICE ACTION - CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
DEACTIVATION OF THE INTERIOR MOVEMENT DETECTOR/TILT ALARM SENSOR IS NOT POSSIBLE: Customer complains that the interior movement detector and the tilt alarm sensor system cannot be deactivated by pressing the lock button on the remote ... Read More »
SERVICE ACTION - REPLACE LEFT FRONT SHORT RANGE RADAR SENSOR (SRR): The functionality of the left front SRR sensor could be reduced which would display the Driving Assistance Check Control Message. Read More »
SERVICE ACTION - REPLACE RIGHT FRONT SHORT RANGE RADAR SENSOR (SRR): The functionality of the right front SRR sensor could be reduced which would display the Driving Assistance Check Control Message. Read More »
REMOTE 3D VIEW NOT AVAILABLE: Remote 3D View cannot be launched In the BMW ConnectedDrive App. Software error in the Advanced Telematics Module 2 (ATM2). Read More »
ACCESSORIES DO NOT POWER ON: Customer is not able to power accessories using the 12 volt power socket. Design change to reduce short circuits and blown fuses. Read More »
SERVICE ACTION: BODY DOMAIN CONTROLLER PROGRAMMING. When the vehicle is left unlocked the interior light switch is continuously monitored. This may lead to an increased battery draw. Read More »
REARVIEW CAMERA. SPORADICALLY NO IMAGE IS DISPLAYED: This Service Information Bulletin (Revision 1) replaces SI B66 31 19 dated October 2019. Read More »
SERVICE ACTION: BODY DOMAIN CONTROLLER PROGRAMMING. When the vehicle is left unlocked the interior light switch is continuously monitored. This may lead to an increased battery draw. Read More »
REMOTE 3D VIEW NOT AVAILABLE: Remote 3D View cannot be launched In the BMW ConnectedDrive App. Software error in the Advanced Telematics Module 2 (ATM2). Read More »
THE MIL MAY BE ILLUMINATED BY ERRONEOUS VALVETRONIC FAULTS. One of the following faults may be stored in the digital motor electronics (DME) either as part of diagnosing a different issue; and-or an illuminated malfunction indicator lamp ... Read More »
ENGINE SPEED DEPENDENT NOISE DURING AUDIO PLAYBACK: Integration level updated. There is an engine speed-dependent noise heard through the speakers during audio playback. Software error in the Receiver Audio Module (RAM) control unit. Read More »
SERVICE ACTION: CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY. In the event of an accident, the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
ETHERNET MODULES STOP RESPONDING OR INCREASED STANDBY CURRENT. A vehicle which was previously programmed to integration level S18A-19-07-525, or up to and including S18A-1907-552 may display the following issues: Fault pattern 1: Failure ... Read More »
WINDOWS WON'T OPERATE WITH DOORS OPEN, AND WHILE USING THE DIGITAL KEY/CARD. The customer complains that none of the windows will operate while any door is open. Read More »
REARVIEW CAMERA: SPORADICALLY NO IMAGE IS DISPLAYED. When reverse gear is selected or the rear view camera is activated, sporadically no image is displayed on the Central Information Display (CID). Read More »
SERVICE ACTION: CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
SERVICE ACTION: BODY DOMAIN CONTROLLER PROGRAMMING: When the vehicle is left unlocked the interior light switch is continuously monitored. This may lead to an increased battery draw. Read More »
HU-H3 MGU HEAD UNIT DOES NOT START CID REMAINS BLACK: If the ignition is briefly switched off and without the vehicle entering sleep mode the MGU (Media Graphics Unit) head unit does not start The CID display remains black. Read More »
APPLE CARPLAY: WI-FI DISCONNECTS AND DOES NOT RECONNECT This Service Information bulletin replaces SI B84 08 19 dated July 2019. The Wi-Fi connection is interrupted (disconnects) and does not reconnect by itself. Read More »
NO INTERIOR HEATING FUNCTION WITH REMOTE START. Customer states that when the vehicle is started using Remote Engine Start the vehicle interior does not heat up despite customer heater settings. Read More »
APPLE CARPLAY: WI-FI DISCONNECTS AND DOES NOT RECONNECT This Service Information bulletin replaces SI B84 08 19 dated July 2019. The Wi-Fi connection is interrupted (disconnects) and does not reconnect by itself. Read More »
SERVICE ACTION: REPLACE KAFAS (CAMERA-BASED DRIVER ASSISTANCE SYSTEM) CAMERA: A malfunction of the KAFAS camera can occur due to a voltage supply fault. Read More »
REMOTE CONTROL IS NOT DETECTED. Vehicle cannot be opened or closed using comfort access engine start is not possible and the vehicle may not start when placing the key again in the steering column. Read More »
COMFORT ACCESS AND COMFORT GO NOT POSSIBLE. Vehicle cannot be opened/locked or started via Comfort Access. Electrostatic charge puts the remote control key into a deep sleep. Read More »
LOCKING AND UNLOCKING WITH DIGITAL KEY NO LONGER FUNCTIONS. After programming the vehicle it is suddenly not possible to unlock or lock the vehicle using the Digital Key or the Digital Key Card. Read More »
DISPLAY IN THE INSTRUMENT CLUSTER OR IN HEAD-UP DISPLAY IS FLICKERING. The customer states that the display in the instrument cluster or the BMW Head-Up Display is flickering. Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE. Additionally the audio source radio station or music track cannot be changed using the MFL. Normal functionality may possibly return after a sleep cycle or a battery reset. Read More »
NIGHT VISION 3: INTERNAL SOFTWARE ERROR FAULT. During vehicle diagnosis of an unrelated issue the following erroneous fault may be stored in the Night Vision 3 control unit. Read More »
APPLE PAY WALLET- POP-UP WINDOW APPEARS IN THE IPHONE DISPLAY. If the customer's iPhone is placed in the center console phone tray which contains either the wireless charging station the NFC station or both; the "Apple Pay Wallet" pop-up ... Read More »
HU-H3/MGU HEAD UNIT AND CENTRAL INFORMATION DISPLAY FAILED. The head unit (HU-H3) and Central Information Display (CID) only work correctly for approx. 1 to 5 minutes after starting the engine. Read More »
CHECK CONTROL MESSAGE BMW DIGITAL KEY. After exchanging the Body Domain Controller (BDC); the digital keys are no longer correctly displayed in the vehicle's Central Information Display. Read More »
DME FAULT MEMORY ENTRY FOR THE CRANKSHAFT SENSOR. Technicians may notice this fault logged during a diagnostic session Fault code Control module Fault Text 160021 DME Crankshaft sensor general loss of synchronism Environmental ... Read More »
?BMW AG has issued a Delivery Stop for BMW X5, X6, X7, and 7 Series sedan vehicles that were produced between July 7, 2023 and August 15, 2023. Usage of the Highway Assist function (option code 5AX) is not possible. Read More »
SERVICE ACTION: PROGRAM OR REPLACE DUAL STORAGE SYSTEM BATTERY: A software error intermittently causes a continuous resetting of the microcontroller in the power management system. Read More »
BATTERY DOES NOT CHARGE WITH EXTERNAL CHARGER AND CLOSED HOOD: After the vehicle has been charged using a 12 V charger with the hood closed during a long stationary period, the 48 V battery may be totally discharged, and possible ... Read More »
SERVICE ACTION: CHECKING THE SIGNAL WIRE AT POWER DISTRIBUTION BOX. The lithium-ion battery in the dual storage system is connected to the terminal 30C to enable issuing a switch-off command in the event of a crash. Read More »
SERVICE ACTION: PROGRAM OR REPLACE DUAL STORAGE SYSTEM BATTERY. A software error intermittently causes a continuous resetting of the microcontroller in the power management system. Read More »
SERVICE ACTION: PROGRAM OR REPLACE DUAL STORAGE SYSTEM BATTERY. A software error intermittently causes a continuous resetting of the microcontroller in the power management system. Read More »
BMW AG has issued a Delivery Stop (effective October 25, 2021) on certain Model Year 2022 BMW vehicles that were produced after October 25, 2021. Read More »
HIGH ENGINE SPEED IMMEDIATELY AFTER STARTING. In rare circumstances after the engine is started with the Start-Stop button the engine speed may immediately increase to a high constant RPM (approximately 3000 rpm). Read More »
REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine. Read More »
When turning off the vehicle, a Check Control Message (CCM) for "rear occupant alert, check rear seats" is displayed in the instrument cluster. Read More »
INSTRUMENT CLUSTER REMAINS DARK AFTER STARTING THE VEHICLE: Instrument cluster remains dark after starting the vehicle. After a restart normal functionality is restored. Software error in the KOMBI (Instrument Cluster). Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE: Instrument Cluster (KOMBSP18) functions are intermittently inoperative including: On-board Computer (BC) button on turn signal stalk (BC button shown at left) Radio ... Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE This Service Information Bulletin (Revision #2) replaces SI B62 01 19 dated March 2019. Updated I-level info. Read More »
INCORRECT VEHICLE IS DISPLAYED IN THE INSTRUMENT CLUSTER AFTER PROGRAMMING. After programming the vehicle from i Level S18A-18-11-5xx to I Level S18A-19-03-5xx an incorrect vehicle model image is displayed in the Instrument Cluster (KOMBI). Read More »
DISPLAY IN THE INSTRUMENT CLUSTER OR IN HEAD-UP DISPLAY IS FLICKERING. The customer states that the display in the instrument cluster or the BMW Head-Up Display is flickering. Read More »
INCORRECT VEHICLE IS DISPLAYED IN THE INSTRUMENT CLUSTER AFTER PROGRAMMING. After programming the vehicle from i Level S18A-18-11-5xx to I Level S18A-19-03-5xx an incorrect vehicle model image is displayed in the Instrument Cluster (KOMBI). Read More »
DISPLAY IN THE INSTRUMENT CLUSTER OR IN HEAD-UP DISPLAY IS FLICKERING. The customer states that the display in the instrument cluster or the BMW Head-Up Display is flickering. Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE. Additionally the audio source radio station or music track cannot be changed using the MFL. Normal functionality may possibly return after a sleep cycle or a battery reset. Read More »
THE INCORRECT VEHICLE IS DISPLAYED IN THE INSTRUMENT CLUSTER AFTER PROGRAMMING. After programming the vehicle from i Level S18A-18-11-5xx to I Level S18A-19-03-5xx an incorrect vehicle model image is displayed in the Instrument Cluster ... Read More »
With the introduction of the BMW Remote Software Upgrade, all Service Pack 18 vehicles and partial Service Pack 15 vehicles may receive new functionality or modifications in their features. Read More »
Delivery Stop: High Beam Assistant. BMW AG has issued a Delivery Stop (effective September 16, 2022) on a small number of Model Year 2023 BMW X7 SAV vehicles that were produced between July 28, 2022 and September 2, 2022. Read More »
BMW AG has issued a Delivery Stop (effective October 25, 2021) on certain Model Year 2022 BMW vehicles that were produced after October 25, 2021. Read More »
The customer may complain of a check control message stating "Safe share detected" (CCM-ID 953). Check control message can be verified by checking key reader information or performing the Check control message history service function. Read More »
WIPERS ACTIVATED WHEN THE VEHICLE IS IN A DRIVE-THROUGH CAR WASH: When the vehicle is in a drive-through car wash with the automatic wiper mode selected, the wipers may activate. Read More »
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. Read More »
BMW CONNECTEDDRIVE APPS ARE NO LONGER AVAILABLE AFTER PROGRAMMING: After programming vehicle with "20-03" software, BMW ConnecedDrive apps are no longer available in the head unit. Software in the Head Unit High (HU-H3). Read More »
KAFAS STOPS RESPONDING AND FAILS PROGRAMMING: During programming of the vehicle the session aborts or the programming fails due to the KAFAS camera (Camera-based Driver Assistance System) no longer responding. Read More »
ACTIVE CRUISE CONTROL (ACC): FRONT MID-RANGE RADAR FAULT CODE 48214E. Only after programming the vehicle with ISTA 4.19.1 or lower the fault code 48214E is set or stored in MidRange Radar (MRR) control module. Read More »
SERVICE ACTION: SOFTWARE QUALITY UPDATE: BMW is offering a one-time X5 and X7 vehicle software update. This software update includes the new voice-activated BMW Intelligent Personal Assistant. Read More »
ERRONEOUS FAULT 1F2505 IS STORED IN THE DME This Service Information bulletin replaces SI B12 30 18 dated November 2018. This fault does not cause any drivability complaints or engine warning lamps. Read More »
DELIVERY STOP: PROGRAM CONTROL UNITS (DME). A Delivery Stop has been issued (effective May 16 2019) on certain Model Year 2016-2020 BMW vehicles that have been produced between June 19 2015 and April 17 2019. Read More »
LOCKING AND UNLOCKING WITH DIGITAL KEY NO LONGER FUNCTIONS. After programming the vehicle it is suddenly not possible to unlock or lock the vehicle using the Digital Key or the Digital Key Card. Read More »
DRIVERS SEAT AND FRONT PASSENGER SEAT CANNOT BE ADJUSTED BACKWARDS. The customer is complaining that the driver's seat and/or the front passenger seat cannot be adjusted backwards. Software error in the seat module(s). Read More »
SERVICE ACTION: PROGRAM OR REPLACE DUAL STORAGE SYSTEM BATTERY. A software error intermittently causes a continuous resetting of the microcontroller in the power management system. Read More »
INCORRECT VEHICLE IS DISPLAYED IN THE INSTRUMENT CLUSTER AFTER PROGRAMMING. After programming the vehicle from i Level S18A-18-11-5xx to I Level S18A-19-03-5xx an incorrect vehicle model image is displayed in the Instrument Cluster (KOMBI). Read More »
Issues with the various functions of the camera-based driver assistance systems (KAFAS system) can possibly lead to following customer complaints: KAFAS camera system deactivates itself, due to system restrictions that are not clear to ... Read More »
Issues with the various functions of the camera-based driver assistance systems (KAFAS system) can possibly lead to following customer complaints: KAFAS camera system deactivates itself, due to system restrictions that are not clear to ... Read More »
ACTIVE PARK DISTANCE CONTROL: SETTING MENU NO LONGER AVAILABLE AFTER PROGRAMMING. The activation setting for Active Park Distance Control (aPDC) is no longer available after programming. Read More »
Headlight check control (CC) message 128 "High beam headlight failure" is displayed. The following fault codes are stored during a vehicle test: 80419A - Left high-beam headlight: Short circuit and/or 8041A5 - light outputs: Number of ... Read More »
The following headlight CC messages are displayed: 128 Left high beam headlight faulty 130 Right high beam headlight faulty; The following fault codes are stored during a vehicle test: 805A22- MLC: Communication fault timeout FLM-03 left ... Read More »
?DAYTIME RUNNING LIGHT IS DIM OR DISCOLORED: One or more of the LED daytime running lights are dim or discolored. The connection between the LED module and light tube inside the headlight is damaged. Read More »
DAYTIME RUNNING LIGHT IS DIM OR DISCOLORED: This Service Information Bulletin (Revision 2) replaces SI B63 04 18 dated January 2019. One or more of the LED daytime running lights are dim or discolored. Read More »
LED LIGHT CARPET IS DIM OR DISTORTED. The light carpet may appear dim or distorted on one or both sides. See the photo below demonstrating the difference side to side. The light carpet LED lens may be blocked by debris. Read More »
The following headlight CC messages are displayed: 128 "Left high beam headlight faulty" 130 "Right high beam headlight faulty" The following fault codes are stored during a vehicle test: 805A22- MLC: Communication fault timeout FLM-03 ... Read More »
Possible failure of lighting operation in either left or right front headlamp assemblies (i.e., daytime driving lights, low beam lights, turn indicators. Read More »
The following headlight CC messages are displayed: 128 Left high beam headlight faulty 130 Right high beam headlight faulty; The following fault codes are stored during a vehicle test: 805A22- MLC: Communication fault timeout FLM-03 left ... Read More »
Delivery Stop: High Beam Assistant. BMW AG has issued a Delivery Stop (effective September 16, 2022) on a small number of Model Year 2023 BMW X7 SAV vehicles that were produced between July 28, 2022 and September 2, 2022. Read More »
?DAYTIME RUNNING LIGHT IS DIM OR DISCOLORED: One or more of the LED daytime running lights are dim or discolored. The connection between the LED module and light tube inside the headlight is damaged. Read More »
Upon opening or closing (i.e., folding in or out) the exterior mirror assembly, a creaking sound is heard from either the driver and/or passenger side. Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
WIPERS ACTIVATED WHEN THE VEHICLE IS IN A DRIVE-THROUGH CAR WASH: When the vehicle is in a drive-through car wash with the automatic wiper mode selected, the wipers may activate. Read More »
SUNROOF NOT INITIALIZED: The sunroof will not operate and has the following fault codes stored: 030215 - SHD: invalid characteristic curve, no standardization exists and 030220 - SHD: System not standardized and 030295 - invalid ... Read More »
WIPERS ACTIVATED WHEN THE VEHICLE IS IN A DRIVE-THROUGH CAR WASH: When the vehicle is in a drive-through car wash with the automatic wiper mode selected, the wipers may activate. Read More »
WIPERS ACTIVATED WHEN THE VEHICLE IS IN A DRIVE-THROUGH CAR WASH: When the vehicle is in a drive-through car wash with the automatic wiper mode selected, the wipers may activate. Read More »
FRONT ROLLER SUNSHADE LOOSE: The roller sunshade (aka sun protection or sunblind) of the front panoramic sunroof is bunching up during operation or may hang down and appear loose. Read More »
TOP VIEW CAMERA: IMAGE IS MISALIGNED: The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). Read More »
WIND NOISE FROM WINDSHIELD SIDE TRIM: A wind noise from the windshield area is present while driving caused by a separation of the windshield side trim (circled) on one or both sides. Read More »
WINDOWS WON'T OPERATE WITH DOORS OPEN, AND WHILE USING THE DIGITAL KEY/CARD. The customer complains that none of the windows will operate while any door is open. Read More »
The roller sunshade (aka sun protection or sunblind) of the front panoramic sunroof is bunching up during operation or may hang down and appear loose. Read More »
SUNROOF WATER LEAK DIAGNOSIS: This bulletin outlines multiple known areas of possible water entry for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting water leak complaints from the roof area. Read More »
FRONT ROLLER SUNSHADE LOOSE. The roller sunshade (aka sun protection or sunblind) of the front panoramic sunroof is bunching up during operation or may hang down and appear loose. Read More »
SUNROOF WATER LEAK DIAGNOSIS: This bulletin outlines multiple known areas of possible water entry for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting water leak complaints from the roof area. Read More »
BUTYL ON ROOF AROUND REAR SUNROOF GLASS. CAUSE Exposure to normal ambient heat can cause the factory-applied sunroof butyl to expand and leak out from around the rear sunroof glass. Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full: Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch. Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full : The low washer fluid warning is illuminated even though the washer fluid reservoir is full. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
The air conditioning cycles from cold to warm air while driving or while at a stand still. The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38 F to 60 F +) without changing any climate control settings. Read More »
When starting the vehicle remotely, the radiator blind of the active air flap control remains closed. This results in inadequate climate control in the vehicle interior. Read More »
The air conditioning cycles from cold to warm air while driving or while at a stand still. The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38 F to 60 F +) without changing any climate control settings. Read More »
3rd ROW CLIMATE CONTROL NOT AVAILABLE: Climate control operations are not available in the 3rd row when the 3rd row seats are folded down. Software in the automatic air conditioning control unit (IHKA). Read More »
BMW of North America, LLC (BMW NA) has a nationwide settlement with the plaintiffs in the following class action: Brightk Consulting, Inc. v. BMW of North America, LLC. The Court has granted final approval of the settlement. Read More »
BMW AG has issued a Delivery Stop (effective October 15, 2021) on certain Model Year 2022 BMW vehicles that were produced between September 28, 2021 and October 8, 2021. The issue involves the Active Crash Safety Module (ACSM) sensor. Read More »
Headlight Malfunction Check Control Message: Intermittently a check control message may be present stating "Adaptive headlight failure" (CC message 127) or "Headlight range control failure" (CC message 100). Read More »
DAYTIME RUNNING LIGHT IS DIM OR DISCOLORED: This Service Information Bulletin (Revision 2) replaces SI B63 04 18 dated January 2019. One or more of the LED daytime running lights are dim or discolored. Read More »
This bulletin outlines known areas of possible water entry, operational noise, or wind noise for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting complaints from the roof area. Read More »
Due to prolonged, normal body flex acting on the vehicle during its service life, a small indentation and/or a crack can form in the body sheetmetal in the right rear wheelwell (aka wheel house). Read More »
While driving the vehicle on normal roads at 10 mph and above, a popping sound from the top of the Cpillar(s) is heard. The sound can occur on either the left or right side of the C-pillar. Read More »
Noise is heard from the seat frame/rail assembly. Noises may occur dynamically (creaking/knocking) when weight is shifting upon the seat Noises may also occur when activating the seat motors. Read More »
SECOND ROW SEAT LEATHER CLOUDY/DISCOLORED: Milky-white stains (discolorations) in the leather are observed in the second-row seat bottom, backrests and/or headrests. Read More »
REWORK SEAT MECHANISM 2ND ROW SEAT: The mounting nuts on the rear left seat frame (60% seat, situated behind the driver's seat) were not properly tightened. Read More »
WIND NOISE FROM WINDSHIELD SIDE TRIM: A wind noise from the windshield area is present while driving caused by a separation of the windshield side trim (circled) on one or both sides. Read More »
SERVICE ACTION: BODY DOMAIN CONTROLLER PROGRAMMING. When the vehicle is left unlocked the interior light switch is continuously monitored. This may lead to an increased battery draw. Read More »
SERVICE ACTION: BODY DOMAIN CONTROLLER PROGRAMMING. When the vehicle is left unlocked the interior light switch is continuously monitored. This may lead to an increased battery draw. Read More »
SUNROOF WATER LEAK DIAGNOSIS: This bulletin outlines multiple known areas of possible water entry for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting water leak complaints from the roof area. Read More »
This bulletin outlines known areas of possible water entry, operational noise, or wind noise for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting complaints from the roof area. Read More »
i>?FUEL FILLER DOOR WILL NOT OPEN: The fuel filler door (aka flap) will not open. In rare cases, if the vehicle is locked using the remote control key and the fuel filler door is pushed closed simultaneously, the fuel door can enter a ... Read More »
The customer states that the vehicle locks itself when the last door was closed, even though the remote control/display key was inside the vehicle. Read More »
FRONY DOOR PANEL LED FAILURES: The LED light on the front door is not working. Due to the orientation of the LED module, moisture may enter the LED module, causing corrosion. Read More »
WHEN LOCKING VEHICLE, DOORS ARE LOCKED BUT VEHICLE IS NOT SECURED: The customer complains that when locking the vehicle from the outside using the remote control: The doors lock The alarm system is not activated The side mirrors (when ... Read More »
DOORS LOCKED WITH REMOTE CONTROL INSIDE THE VEHICLE. The customer states that the vehicle locks itself when the last door was closed even though the remote control/display key was inside the vehicle. Read More »
SERVICE ACTION: CHECK AND APPLY CAVITY PROTECTION ON DRIVER'S FRONT DOOR. Insufficient cavity protection may have been applied to the driver front door. During production insufficient cavity protection may have been applied. Read More »
SERVICE ACTION: CHECK AND APPLY CAVITY PROTECTION ON DRIVER'S FRONT DOOR. Insufficient cavity protection may have been applied to the driver front door. During production insufficient cavity protection may have been applied. Read More »
The tailgate will not completely open and will not close completely. In most cases, the tailgate will release and open only a short distance before stopping. In some situations, a humming noise can be heard, but no activation can be seen. Read More »
BATTERY DOES NOT CHARGE WITH EXTERNAL CHARGER AND CLOSED HOOD: After the vehicle has been charged using a 12 V charger with the hood closed during a long stationary period, the 48 V battery may be totally discharged, and possible ... Read More »
Delivery Stop: Roof fin. BMW AG has issued a Delivery Stop (effective September 16, 2022) on a small number of Model Year 2022 - 2023 BMW vehicles that were produced on July 26, 2022. Read More »
The roller sunshade (aka sun protection or sunblind) of the front panoramic sunroof is bunching up during operation or may hang down and appear loose. Read More »
WHEN LOCKING VEHICLE, DOORS ARE LOCKED BUT VEHICLE IS NOT SECURED: The customer complains that when locking the vehicle from the outside using the remote control: The doors lock. The alarm system is not activated. Read More »
COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: This Service Information Bulletin (Revision 1) replaces SI B66 19 19 dated May 2019. Vehicle cannot be unlocked/locked or started via Comfort Access. Read More »
DOORS LOCKED WITH REMOTE CONTROL INSIDE THE VEHICLE. The customer states that the vehicle locks itself when the last door was closed even though the remote control/display key was inside the vehicle. Read More »
When using Comfort Access 2.0 feature Lock when walking away, the vehicle locks itself even though the remote control/display key is inside the vehicle. Read More »
FUEL FILLER DOOR STICKING: The fuel filler door may be sticking requiring multiple attempts to open. The fuel filler door material can swell in wet conditions causing the filler door to stick. Read More »
ACTIVE CRUISE CONTROL - UNEXPECTED DECELERATION: Vehicle slows down (decelerates) unexpectedly while Active Cruise Control with Stop & Go (ACC) function is activated. Read More »
Due to prolonged, normal body flex acting on the vehicle during its service life, a small indentation and/or a crack can form in the body sheetmetal in the right rear wheelwell (aka wheel house). Read More »
REWORK SEAT MECHANISM 2ND ROW SEAT: The mounting nuts on the rear left seat frame (60% seat, situated behind the driver's seat) were not properly tightened. Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving. Read More »
JERKING OR SHUDDERING FROM THE DRIVELINE (XDRIVE TRANSFER CASE ATX13-X): There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no ... Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
Service Information May 2019 Special Suspension Systems B37 01 19 Technical Service CHECK CONTROL MESSAGE (CCM) DRIVING COMFORT RESTRICTED. Chassis stabilization warning and CCM Driving comfort restricted. Read More »
Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Third-row seating, on one or both sides, cannot be folded down. Read More »
Second seat row blocking access to third seat row, program seat modules. Visible stitching on first row sport seat. Third seat row backrest Bowden cable routing and length change. Read More »
When returning the 2nd row seat 60/40 seat from Easy-Entry: The seat stops moving before reaching the final home position. A Check Control Message (CCM) appears alerting the customer that the seat is not locked. Read More »
Noise is heard from the seat frame/rail assembly. Noises may occur dynamically (creaking/knocking) when weight is shifting upon the seat Noises may also occur when activating the seat motors. Read More »
When returning the 2nd row seat 60% (left) side from Easy-Entry: The seat stops moving before reaching the final home position, a check control message (CCM) appears alerting the customer that the seat back is unlocked. Read More »
The passenger's side (right rear) of the 60/40 split 2nd row seat may intermittently not fully latch into position on one side (inner rail). Read More »
Milky-white stains (discolorations) in the leather are observed in the second-row seat bottom, backrests and/or headrests. Refer to attachment for details. This only affects vehicles with the Merino leather. Read More »
Noise is heard from the seat frame/rail assembly. Noises may occur dynamically (creaking/knocking) when weight is shifting upon the seat Noises may also occur when activating the seat motors. Read More »
With the launch of the G05 (X5) Sports Activity Vehicle in August 2018, a new style of networked seats was introduced that have new operating parameters. This service information bulletin details the operation of the new style seats. Read More »
HEAD RESTRAINT AND/OR BACKREST OF 3RD ROW SEATS CANNOT BE FOLDED DOWN: Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Read More »
HEAD RESTRAINT AND/OR BACKREST OF 3RD ROW SEATS CANNOT BE FOLDED DOWN: Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Read More »
SECOND ROW SEAT LEATHER CLOUDY/DISCOLORED: Milky-white stains (discolorations) in the leather are observed in the second-row seat bottom, backrests and/or headrests. Read More »
OUTER HEADREST SECOND ROW: BMW AG has issued a Delivery Stop on certain Model Year 2021 BMW X5 SAV and X7 SAV vehicles that were produced between February 8, 2021 and February 17, 2021. Read More »
THIGH SUPPORT UPHOLSTERY DETACHES FROM SEAT: The seat leather upholstery detaches from the front of the thigh support (aka knee bolster) of either front seat. Read More »
?NO PREVIEW IMAGES DISPLAYED IN THE REAR SEAT ENTERTAINMENT: The rear seat entertainment screens do not display any preview images at times. Read More »
HEAD RESTRAINT AND/OR BACKREST OF 3RD ROW SEATS CANNOT BE FOLDED DOWN: Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Read More »
HOLE IN LEATHER AT SIDE LOCK BOLT, 2ND ROW 60/40 SPLIT BENCH SEAT: There is a visible hole in the leather of the 2nd row of seats. The hole is located on the side lock bolt of the left rear seat backrest. Read More »
HOLE IN LEATHER AT SIDE LOCK BOLT, 2ND ROW 60/40 SPLIT BENCH SEAT: There is a visible hole in the leather of the 2nd row of seats. The hole is located on the side lock bolt of the left rear seat backrest. Read More »
SEAT HEATING NOT ACTIVATED WHEN ENGINE IS STARTED USING REMOTE STARTING SYSTEM: When preheating/precooling the vehicle via the remote starting system (Remote Engine Start), the seat heating on the driver's side is not activated. Read More »
BACKREST MISALIGNMENT OF 60/40 SECOND ROW SEAT: On vehicles equipped with the second row 60/40 split bench seats, the backrests may not properly align between the two seats. Read More »
SOFTWARE UPDATE FOR SEAT CHECK CONTROL MESSAGES: There is an operating failure with various Check Control (CC) messages displayed regarding seat adjustment of the second and third row of seats. Read More »
3rd ROW CLIMATE CONTROL NOT AVAILABLE: Climate control operations are not available in the 3rd row when the 3rd row seats are folded down. Software in the automatic air conditioning control unit (IHKA). Read More »
SECOND ROW 60/40 DRIVERS SIDE SEAT INTERMITTENTLY WON'T LATCH This Service Information Bulletin (Revision #2) replaces SI B52 04 19 dated July 2019. Read More »
SECOND ROW SEATS INTERMITTENTLY ELECTRONICALLY INOPERATIVE. The second and/or third row of seats intermittently may not electronically function preventing third row access. Read More »
SECOND ROW 60/40 PASSENGERS SIDE SEAT INTERMITTENTLY WON'T LATCH. The passenger's side (right rear) of the 60/40 split 2nd row seat may intermittently not fully latch into position on one side (inner rail). Read More »
SEAT OPERATIONAL CHANGES AS OF 7/2019 I-LEVEL FOR G05/G07. The seat switch located in the left rear of the trunk area has a hardware change as of 7/2019. Read More »
CREASES/RIPPLES IN THE 2ND ROW 60/40 BENCH SEAT BACKREST SYNTHETIC LEATHER COVER: There are creases/ripples in the leather upholstery of the upper part of the backrest for the 2nd row of seats. This only applies to the 60/40 bench seat. Read More »
SECOND ROW 60/40 DRIVERS SIDE SEAT INTERMITTENTLY WON'T LATCH. The driver's side (left rear) of the 60/40 split 2nd row seat may intermittently not fully latch into position on one side (inner rail). Read More »
THIGH SUPPORT UPHOLSTERY DETACHES FROM SEAT. The seat leather upholstery detaches from the front of the thigh support (aka knee bolster) of either front seat. The metal retainer clips on the thigh support are too loose. Read More »
DRIVERS SEAT AND FRONT PASSENGER SEAT CANNOT BE ADJUSTED BACKWARDS. The customer is complaining that the driver's seat and/or the front passenger seat cannot be adjusted backwards. Software error in the seat module(s). Read More »
NOISE FROM FRONT SEAT HEADREST: When adjusting the headrest scissor mechanism (aka side extensions or "wings") a groaning noise can be heard. Read More »
DRIVERS SEAT AND FRONT PASSENGER SEAT CANNOT BE ADJUSTED BACKWARDS. The customer is complaining that the driver's seat and/or the front passenger seat cannot be adjusted backwards. Software error in the seat module(s). Read More »
SEAT HEATING NOT ACTIVATED WHEN ENGINE IS STARTED USING REMOTE STARTING SYSTEM: When preheating/precooling the vehicle via the remote starting system (Remote Engine Start), the seat heating on the driver's side is not activated. Read More »
When turning off the vehicle, a Check Control Message (CCM) for "rear occupant alert, check rear seats" is displayed in the instrument cluster. Read More »
Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Third-row seating, on one or both sides, cannot be folded down. Read More »
Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Third-row seating, on one or both sides, cannot be folded down. Read More »
SERVICE ACTION - REPLACE HYDRAULIC UNIT, DYNAMIC STABILITY CONTROL INTEGRATED: DSCi units which potentially have a faulty hydraulic valve were installed in the vehicles. Read More »
Service Information May 2019 Special Suspension Systems B37 01 19 Technical Service CHECK CONTROL MESSAGE (CCM) DRIVING COMFORT RESTRICTED. Chassis stabilization warning and CCM Driving comfort restricted. Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
BMW AG has issued a Delivery Stop (effective October 15, 2021) on certain Model Year 2022 BMW vehicles that were produced between September 28, 2021 and October 8, 2021. The issue involves the Active Crash Safety Module (ACSM) sensor. Read More »
IB BRAKE-BY-WIRE SYSTEM - PREFLIGHT CHECK. When starting a vehicle or driving off customers may complain of "no brake assist" or "hard brake pedal". Read More »
FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA
SERVICE ACTION: REPLACE KAFAS (CAMERA-BASED DRIVER ASSISTANCE SYSTEM) CAMERA. A malfunction of the KAFAS camera can occur due to a voltage supply fault. Read More »
DRIVER CAMERA SYSTEM: NO FACE DETECTED FAULT CODE. During vehicle diagnosis fault code 808607 (No face detected) may be stored in the Driver Camera System (DCS) control unit. Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
The Lane Change Warning (LCW) yellow triangle symbol on either one, or both the exterior side view mirrors does not illuminate to alert the driver when it should. Read More »
The steering intervention for Lane Departure Warning (LDW) is too strong (severe), which can create an uncomfortable feeling for the driver. Read More »
LANE DEPARTURE WARNING - STEERING INTERVENTION TOO STRONG: The steering intervention for Lane Departure Warning (LDW) is too strong (severe), which can create an uncomfortable feeling for the driver. Read More »
COOLANT LINE QUICK DISCONNECTS LEAK IN LOW TEMPERATURES AT OR BELOW -15E?C (5E?F): The coolant reservoir in the high or low temperature cooling system is low There may be a coolant leak under the vehicle There may be a check control ... Read More »
JERKING OR SHUDDERING FROM THE DRIVELINE (XDRIVE TRANSFER CASE ATX13-X): There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no ... Read More »
TOP VIEW CAMERA: IMAGE IS MISALIGNED. The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). Read More »
LANE DEPARTURE WARNING: STEERING WHEEL VIBRATION INSUFFICIENT. Lane Departure Warning (LDW) vibration of the steering wheel is not sufficient (too weak). Vibration actuator software. Read More »
LANE DEPARTURE WARNING: STEERING INTERVENTION TOO STRONG. The steering intervention for Lane Departure Warning (LDW) is too strong (severe) which can create an uncomfortable feeling for the driver. Read More »
LANE DEPARTURE WARNING: STEERING WHEEL VIBRATION INSUFFICIENT. Lane Departure Warning (LDW) vibration of the steering wheel is not sufficient (too weak). Vibration actuator software. Read More »
DRIVERS ASSISTANCE SYSTEM LIMITED SUPPORT CHECK CONTROL MESSAGE. INFORMATION Part Number Description Quantity Refer to ETK KaFAS camera (Control unit and camera). Read More »
INTERRUPTION OF AUTOMATED PARK ASSIST. Park Distance Control (PDC) distance tiles are displayed in the Central Information Display (CID); despite no actual obstacles being in close proximity to the vehicle. Read More »
LANE DEPARTURE:LANE KEEP:NAVIGATION SYSTEM/SOFTWARE
DRIVERS ASSISTANCE SYSTEM LIMITED SUPPORT CHECK CONTROL MESSAGE. INFORMATION Part Number Description Quantity Refer to ETK KaFAS camera (Control unit and camera). Read More »
TOP VIEW CAMERA IMAGE IS MISALIGNED: The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). Read More »
SURROUND VIEW - PARKING VIEW IMAGES DISPLAYED INCORRECTLY: After programming and shifting into reverse, there may be various sporadic concerns regarding the rearview camera and the surround view (top view) camera images in the CID ... Read More »
TOP VIEW CAMERA: IMAGE IS MISALIGNED: The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). Read More »
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Read More »
REARVIEW CAMERA. SPORADICALLY NO IMAGE IS DISPLAYED: This Service Information Bulletin (Revision 1) replaces SI B66 31 19 dated October 2019. Read More »
TOP VIEW CAMERA: IMAGE IS MISALIGNED. The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). Read More »
?During workshop repairs with software updates, certain customer vehicles may be changed to BMW Operating System 8.5 and returned to customers without making them aware of the change. Read More »
In some rare cases a customer vehicle might be excluded from one or more Remote Software Upgrade(RSU) campaigns. This SIB gives an overview how to identify these vehicles and how to proceed in case of a customer complaint. Read More »
BMW REMOTE SOFTWARE UPGRADE IS NOT OFFERED FOR INSTALLATION: The customer complains that the BMW Remote Software Upgrade (RSU) is not possible in his/her vehicle, though the Remote Software Upgrade menu is available in the vehicle and a ... Read More »
REARVIEW CAMERA: SPORADICALLY NO IMAGE IS DISPLAYED. When reverse gear is selected or the rear view camera is activated, sporadically no image is displayed on the Central Information Display (CID). Read More »
FRONY DOOR PANEL LED FAILURES: The LED light on the front door is not working. Due to the orientation of the LED module, moisture may enter the LED module, causing corrosion. Read More »
LED LIGHT CARPET IS DIM OR DISTORTED. The light carpet may appear dim or distorted on one or both sides. See the photo below demonstrating the difference side to side. The light carpet LED lens may be blocked by debris. Read More »
?BMW AG has issued a Delivery Stop for BMW X5, X6, X7, and 7 Series sedan vehicles that were produced between July 7, 2023 and August 15, 2023. Usage of the Highway Assist function (option code 5AX) is not possible. Read More »
The original Conditioned Based Service (CBS) Key data point closed with 23-07 soft ware, all CBS systems are now collectively under analysis. Read More »
The roller sunshade (aka sun protection or sunblind) of the front panoramic sunroof is bunching up during operation or may hang down and appear loose. Read More »
When using the Key Reader to retrieve CBS information from the customer key, no current vehicle data is available, or the data does not match the maintenance schedule. Read More »
Customers may be experiencing one or more of these following issues with Bluetooth operation: Bluetooth cannot be switched on or off in the head unit (HU-H4) Paired mobile devices cannot be deleted Customer is unable to make phone ... Read More »
Interim Class Action Settlement F95/96, G05/G06/G07 front center console cupholder United States District Court Central District of California. Read More »
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. Read More »
While driving the vehicle on normal roads at 10 mph and above, a popping sound from the top of the Cpillar(s) is heard. The sound can occur on either the left or right side of the C-pillar. Read More »
Due to component-related supply issues, the central information displays (CID) in some of the Model Year 2022 vehicles listed above were produced without the integrated touch screen function. Read More »
BMW AG has issued a Delivery Stop (effective October 25, 2021) on certain Model Year 2022 BMW vehicles that were produced after October 25, 2021. Read More »
Programming of various modules will provide quality improvements and system robustness to: Valet parking mode, accessed via the Center Information Display (CID) app System Settings. Read More »
The following LIN faults for electric door sunshade may be present in the BDC fault memory. D90D81-Sunblind rear driver (LIN): Missing LIN-slave D90D84-Sunblind rear passenger (LIN): Missing LIN-slave 8049B2-Sunblind rear driver (LIN): ... Read More »
The incorrect Bluetooth module was installed in the headunit. Bluetooth functionality cannot be guaranteed, and mobile phones may possibly not be paired via Bluetooth. Read More »
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. Read More »
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
The following LIN faults for electric door sunshade may be present in the BDC fault memory. D90D81-Sunblind rear driver (LIN): Missing LIN-slave D90D84-Sunblind rear passenger (LIN): Missing LIN-slave 8049B2-Sunblind rear driver (LIN): ... Read More »
The Check Control message below appears even though the coolant level is not below minimum when the engine is cold. Check Control message (ID 166): Top up coolant. Read More »
Information updated about engine oil filter cap drain plug. When performing an engine oil service on vehicles equipped with a N63M, N63B or S63M engines; the ETK states to use "Set oil filter element" P/N 11 42 5 A33 C42 or P/N 11 42 5 ... Read More »
The steering intervention for Lane Departure Warning (LDW) is too strong (severe), which can create an uncomfortable feeling for the driver. Read More »
While using the wireless charger, one or both of the following may occur: 1) The BMW display key or mobile phone becomes hot to the touch. 2) The device switches off due to over temperature (built-in device protection). Read More »
On rare occasions during an engine oil service, the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. Read More »
Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Third-row seating, on one or both sides, cannot be folded down. Read More »
The customer may complain of a check control message stating "Safe share detected" (CCM-ID 953). Check control message can be verified by checking key reader information or performing the Check control message history service function. Read More »
HEAD RESTRAINT AND/OR BACKREST OF 3RD ROW SEATS CANNOT BE FOLDED DOWN: Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Read More »
SERVICE ACTION: PROGRAM OR REPLACE DUAL STORAGE SYSTEM BATTERY: A software error intermittently causes a continuous resetting of the microcontroller in the power management system. Read More »
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Read More »
WIPERS ACTIVATED WHEN THE VEHICLE IS IN A DRIVE-THROUGH CAR WASH: When the vehicle is in a drive-through car wash with the automatic wiper mode selected, the wipers may activate. Read More »
PROGRAMING THE DUAL STORAGE SYSTEM AND REPLACE IT IF NECESSARY: The 12 V battery's dual storage system (DSS) may contain a software error which intermittently causes a continuous resetting of the microcontroller and communication failure. Read More »
CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident, the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
FRONY DOOR PANEL LED FAILURES: The LED light on the front door is not working. Due to the orientation of the LED module, moisture may enter the LED module, causing corrosion. Read More »
BMW REMOTE SOFTWARE UPGRADE IS NOT OFFERED FOR INSTALLATION: The customer complaints that the BMW Remote Software Upgrade (RSU) is not possible in their vehicle, though the Remote Software Upgrade menu is available in the vehicle and a ... Read More »
REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine. A manufacturing defect affecting the ignition coil insulation. Read More »
THIGH SUPPORT UPHOLSTERY DETACHES FROM SEAT: The seat leather upholstery detaches from the front of the thigh support (aka knee bolster) of either front seat. Read More »
SUNROOF NOT INITIALIZED: The sunroof will not operate and has the following fault codes stored: 030215 - SHD: invalid characteristic curve, no standardization exists and 030220 - SHD: System not standardized and 030295 - invalid ... Read More »
WHEN LOCKING VEHICLE, DOORS ARE LOCKED BUT VEHICLE IS NOT SECURED: The customer complains that when locking the vehicle from the outside using the remote control: The doors lock The alarm system is not activated The side mirrors (when ... Read More »
MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED WITH FAULT MEMORY CDC152: The malfunction indicator lamp (MIL) is illuminated in the instrument cluster. The vehicles has no operating failures; only the MIL is illuminated. Read More »
REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
?NO PREVIEW IMAGES DISPLAYED IN THE REAR SEAT ENTERTAINMENT: The rear seat entertainment screens do not display any preview images at times. Read More »
HEAD RESTRAINT AND/OR BACKREST OF 3RD ROW SEATS CANNOT BE FOLDED DOWN: Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Read More »
CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident, the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full: Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch. Read More »
HEAD UNIT RESETS WITH FAULT CODE B7F8F9 RESET WATCHDOG: Customer states the following about their vehicle: Active radio or music source is interrupted. The navigation is no longer available. A black screen is shown in the Control Display. Read More »
HOLE IN LEATHER AT SIDE LOCK BOLT, 2ND ROW 60/40 SPLIT BENCH SEAT: There is a visible hole in the leather of the 2nd row of seats. The hole is located on the side lock bolt of the left rear seat backrest. Read More »
ACCESSORIES DO NOT POWER ON: Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Read More »
WIPERS ACTIVATED WHEN THE VEHICLE IS IN A DRIVE-THROUGH CAR WASH: When the vehicle is in a drive-through car wash with the automatic wiper mode selected, the wipers may activate. Read More »
CENTER CONSOLE / CUP HOLDER GETS HOT WHEN THE HEAT IS ON: The center console and front cup holder get noticeably too warm to the touch on long journeys with the interior "Heating on". Read More »
DELIVERY STOP - INSPECT NUTS ON CATALYTIC CONVERTER: BMW AG has issued a Delivery Stop (effective June 23, 2020) on certain Model Year 2020 BMW vehicles that were produced between March 10, 2020 and June 1, 2020. Read More »
SUNROOF WATER LEAK DIAGNOSIS: This bulletin outlines multiple known areas of possible water entry for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting water leak complaints from the roof area. Read More »
DISPLAYS SPORADICALLY REACT VERY SLOWLY WHEN SCROLLING IN THE AUDIO MENU: Sporadically the reaction time of the display in the instrument cluster the head-up display or in the CID (Central Information Display) is very long. Read More »
FIBERS PROTRUDING FROM CENTER SPEAKER COVER: Fibers are protruding from beneath the center dashboard speaker cover. Insulation material underneath the speaker may become loose. Read More »
SERVICE ACTION - CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
DISPLAY KEY IS NON-FUNCTIONAL: This Service Information Bulletin (Revision 3) replaces SI B66 20 17 dated October 2019. The display key is non-functional. Display Key cannot be charged or switched on. Read More »
DOORS LOCKED WITH REMOTE CONTROL INSIDE THE VEHICLE. The customer states that the vehicle locks itself when the last door was closed even though the remote control/display key was inside the vehicle. Read More »
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full : The low washer fluid warning is illuminated even though the washer fluid reservoir is full. Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE: Instrument Cluster (KOMBSP18) functions are intermittently inoperative including: On-board Computer (BC) button on turn signal stalk (BC button shown at left) Radio ... Read More »
ENGINE SPEED DEPENDENT NOISE DURING AUDIO PLAYBACK: Integration level updated. There is an engine speed-dependent noise heard through the speakers during audio playback. Software error in the Receiver Audio Module (RAM) control unit. Read More »
NO AUDIO IS AVAILABLE FOR APPROXIMATELY 30 SECONDS AFTER HEAD UNIT START UP: After programming vehicle no audio is available for approximately 30 seconds after head unit start-up. Read More »
SERVICE ACTION: REPLACE KAFAS (CAMERA-BASED DRIVER ASSISTANCE SYSTEM) CAMERA. A malfunction of the KAFAS camera can occur due to a voltage supply fault. Read More »
DISPLAY KEY IS NON-FUNCTIONAL. This Service Information Bulletin (Revision 2) replaces SI B66 20 17 dated September 2018. What's New: The display key is non-functional. Display Key cannot be charged or switched on. Read More »
KAFAS STOPS RESPONDING AND FAILS PROGRAMMING: During programming of the vehicle the session aborts or the programming fails due to the KAFAS camera (Camera-based Driver Assistance System) no longer responding. Read More »
SERVICE ACTION: CHECKING THE DUAL STORAGE SYSTEM AND REPLACE IF NECESSARY: In the event of an accident the two-battery Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. Read More »
DRIVER CAMERA SYSTEM: NO FACE DETECTED FAULT CODE. During vehicle diagnosis fault code 808607 (No face detected) may be stored in the Driver Camera System (DCS) control unit. Read More »
NO INTERIOR HEATING FUNCTION WITH REMOTE START. Customer states that when the vehicle is started using Remote Engine Start the vehicle interior does not heat up despite customer heater settings. Read More »
LOCKING AND UNLOCKING WITH DIGITAL KEY NO LONGER FUNCTIONS. After programming the vehicle it is suddenly not possible to unlock or lock the vehicle using the Digital Key or the Digital Key Card. Read More »
SERVICE ACTION: N63M ENGINES - CHECK AND REPLACE THE FRESH AIR INTAKE DUCT. The incorrect crankcase ventilation non return valves may have been installed in the vehicle. Read More »
IB BRAKE-BY-WIRE SYSTEM - PREFLIGHT CHECK. When starting a vehicle or driving off customers may complain of "no brake assist" or "hard brake pedal". Read More »
SERVICE ACTION: PROGRAM OR REPLACE DUAL STORAGE SYSTEM BATTERY. A software error intermittently causes a continuous resetting of the microcontroller in the power management system. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
INCORRECT VEHICLE IS DISPLAYED IN THE INSTRUMENT CLUSTER AFTER PROGRAMMING. After programming the vehicle from i Level S18A-18-11-5xx to I Level S18A-19-03-5xx an incorrect vehicle model image is displayed in the Instrument Cluster (KOMBI). Read More »
DRIVERS ASSISTANCE SYSTEM LIMITED SUPPORT CHECK CONTROL MESSAGE. INFORMATION Part Number Description Quantity Refer to ETK KaFAS camera (Control unit and camera). Read More »
COMFORT GO NOT POSSIBLE. If the radio operated key (ID transmitter/display key) is located in the glove box compartment Comfort Go (engine start) is not possible. Read More »
APPLE PAY WALLET- POP-UP WINDOW APPEARS IN THE IPHONE DISPLAY. If the customer's iPhone is placed in the center console phone tray which contains either the wireless charging station the NFC station or both; the "Apple Pay Wallet" pop-up ... Read More »
HU-H3/MGU HEAD UNIT AND CENTRAL INFORMATION DISPLAY FAILED. The head unit (HU-H3) and Central Information Display (CID) only work correctly for approx. 1 to 5 minutes after starting the engine. Read More »
CHECK CONTROL MESSAGE BMW DIGITAL KEY. After exchanging the Body Domain Controller (BDC); the digital keys are no longer correctly displayed in the vehicle's Central Information Display. Read More »
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
The customer states that the vehicle locks itself when the last door was closed, even though the remote control/display key was inside the vehicle. Read More »
With the introduction of BMW Remote Software Upgrade, all Service Pack 18 vehicles and partial Service Pack 15 vehicles may receive new functionalities or modifications in their features with a new Software Update. Read More »
In some rare cases a customer vehicle might be excluded from one or more Remote Software Upgrade (RSU) campaigns. This SIB gives an overview how to identify these vehicles and how to proceed in case of a customer complaint. Read More »
DSCi units which potentially have a faulty hydraulic valve were installed in the vehicles. The affected unitsmay activate a sporadic red-colored Check Control Message. Read More »
The customer may complain of a check control message stating "Safe share detected" (CCM-ID 953). Check control message can be verified by checking key reader information or performing the Check control message history service function. Read More »
Check control message (CCM-ID 49) "You can continue driving. Drivetrain". In addition, the following information is shown on the Central Information Display (CID): "You can continue to drive. No roadside assistance necessary. Read More »
REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle maynot start when placing the key against the steering column. Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE: The audio source, radio station, or music track cannot be changed using the MFL. Normal functionality may possibly return after a sleep cycle or a battery reset. Read More »
COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: This Service Information Bulletin (Revision 1) replaces SI B66 19 19 dated May 2019. Vehicle cannot be unlocked/locked or started via Comfort Access. Read More »
NO AUDIO IS AVAILABLE FOR APPROXIMATELY 30 SECONDS AFTER HEAD UNIT START UP: After programming vehicle no audio is available for approximately 30 seconds after head unit start-up. Read More »
SERVICE ACTION: REPLACE KAFAS (CAMERA-BASED DRIVER ASSISTANCE SYSTEM) CAMERA. A malfunction of the KAFAS camera can occur due to a voltage supply fault. Read More »
CONNECTEDDRIVE: BMW APPS AND SERVICES NOT AVAILABLE. The BMW ConnectedDrive Services are no longer available in the vehicle nor are the BMW Apps displayed in the vehicle. Read More »
APPLE CARPLAY: WI-FI DISCONNECTS AND DOES NOT RECONNECT This Service Information bulletin replaces SI B84 08 19 dated July 2019. The Wi-Fi connection is interrupted (disconnects) and does not reconnect by itself. Read More »
LOCKING AND UNLOCKING WITH DIGITAL KEY NO LONGER FUNCTIONS. After programming the vehicle it is suddenly not possible to unlock or lock the vehicle using the Digital Key or the Digital Key Card. Read More »
CHECK CONTROL MESSAGE BMW DIGITAL KEY. After exchanging the Body Domain Controller (BDC); the digital keys are no longer correctly displayed in the vehicle's Central Information Display. Read More »
FALSE ALARM ACTIVATION TRIGGERED BY INTERIOR ULTRASOUND SENSOR: The DWA (anti-theft alarm) triggers for no apparent reason with all the vehicle's doors and windows closed. Read More »
Delivery Stop: Roof fin. BMW AG has issued a Delivery Stop (effective September 16, 2022) on a small number of Model Year 2022 - 2023 BMW vehicles that were produced on July 26, 2022. Read More »
Customer states there is no audio playback (telephony, navigation, radio) and system sounds (PDC, turn indicators, acoustic signals) may also have failed. Read More »
HEAD UNIT RESETS WITH FAULT CODE B7F8F9 RESET WATCHDOG: Customer states the following about their vehicle: Active radio or music source is interrupted. The navigation is no longer available. A black screen is shown in the Control Display. Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE. Additionally the audio source radio station or music track cannot be changed using the MFL. Normal functionality may possibly return after a sleep cycle or a battery reset. Read More »
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. Read More »
HEAD UNIT RESETS WITH FAULT CODE B7F8F9 RESET WATCHDOG: Customer states the following about their vehicle: Active radio or music source is interrupted. The navigation is no longer available. A black screen is shown in the Control Display. Read More »
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. Read More »
The Central Information Display goes black intermittently due to resets of the Head Unit (HU-H3). FaultB7F8F9 ??A???A???A???A???A???A? ??A???A???A???A???A???A?HU-H: Reset??A???A???A???A???A???A? will be stored in the HU-H3. Read More »
Programming of various modules will provide quality improvements and system robustness to: Valet parking mode, accessed via the Center Information Display (CID) app System Settings. Read More »
?NO PREVIEW IMAGES DISPLAYED IN THE REAR SEAT ENTERTAINMENT: The rear seat entertainment screens do not display any preview images at times. Read More »
The incorrect Bluetooth module was installed in the headunit. Bluetooth functionality cannot be guaranteed, and mobile phones may possibly not be paired via Bluetooth. Read More »
HU-H3 MGU RESETS DUE TO BLUETOOTH CONNECTION WITH SAMSUNG ANDROID 11 : The head unit resets when using various apps (e.g., YouTube, Spotify, etc) on the connected mobile phone. This affects Samsung mobile phones (e.g. Read More »
Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained. Read More »
HEAD RESTRAINT AND/OR BACKREST OF 3RD ROW SEATS CANNOT BE FOLDED DOWN: Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Read More »
Deactivated: Currently investigating other components that maybe playing a factors besides what is mentioned in the SIB. Topic is under investigation. Read More »
BMW AG has issued a Delivery Stop effective June 6, 2023 on certain Model Year 2023 - 2024 BMW vehicles that were produced between October 26, 2022 and May 8, 2023. Read More »
BMW AG has issued a Delivery Stop (effective November 10, 2022) on a small number of Model Year 2023 BMW vehicles that were produced between August 8, 2022 and October 18, 2022. Read More »
This Service Information Bulletin (Revision 11) replaces TRI B52 23 19 dated February 20212. This bulletin is information only, no claim information intended. Read More »
This bulletin outlines known areas of possible water entry, operational noise, or wind noise for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting complaints from the roof area. Read More »
BMW AG has issued a Delivery Stop (effective October 25, 2021) on certain Model Year 2022 BMW vehicles that were produced after October 25, 2021. Read More »
NEW ECU VALIDATION NEEDED AFTER REPLACING CERTAIN CONTROL MODULES: With introduction of the new Headunit HU-H3 (MGU Media Graphics Unit), there is a new protection mechanism against tampering. Read More »
SUNROOF WATER LEAK DIAGNOSIS: This bulletin outlines multiple known areas of possible water entry for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting water leak complaints from the roof area. Read More »
INFORMATION New information provided by this revision is preceded by this symbol. This Service Information bulletin replaces SI B84 02 14 dated September 2018. Read More »
Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Third-row seating, on one or both sides, cannot be folded down. Read More »
HEAD RESTRAINT AND/OR BACKREST OF 3RD ROW SEATS CANNOT BE FOLDED DOWN: Various concerns about the third row of seats: 1. Head restraint (aka headrest), on one or both sides, cannot be folded down. 2. Read More »
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Read More »
WHEN LOCKING VEHICLE, DOORS ARE LOCKED BUT VEHICLE IS NOT SECURED: The customer complains that when locking the vehicle from the outside using the remote control: The doors lock The alarm system is not activated The side mirrors (when ... Read More »
REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Read More »
HOLE IN LEATHER AT SIDE LOCK BOLT, 2ND ROW 60/40 SPLIT BENCH SEAT: There is a visible hole in the leather of the 2nd row of seats. The hole is located on the side lock bolt of the left rear seat backrest. Read More »
ACCESSORIES DO NOT POWER ON: Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Read More »
WIPERS ACTIVATED WHEN THE VEHICLE IS IN A DRIVE-THROUGH CAR WASH: When the vehicle is in a drive-through car wash with the automatic wiper mode selected, the wipers may activate. Read More »
NEW ECU VALIDATION NEEDED AFTER REPLACING CERTAIN CONTROL MODULES: With introduction of the new Headunit HU-H3 (MGU Media Graphics Unit), there is a new protection mechanism against tampering. Read More »
DISPLAYS SPORADICALLY REACT VERY SLOWLY WHEN SCROLLING IN THE AUDIO MENU: Sporadically the reaction time of the display in the instrument cluster the head-up display or in the CID (Central Information Display) is very long. Read More »
DIAGNOSTIC HINT: DRIVING ASSISTANCE SUPPORT REDUCED CHECK CONTROL MESSAGE DISP: Driving Assistance support reduced Check Control Message (CCM) is displayed sporadically. All or some of the system functions maybe inoperative. Read More »
REARVIEW CAMERA: SPORADICALLY NO IMAGE IS DISPLAYED: This Service Information Bulletin (Revision 2) replaces SI B66 31 19 dated February 2020. Read More »
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. Read More »
FRONT ROLLER SUNSHADE LOOSE. The roller sunshade (aka sun protection or sunblind) of the front panoramic sunroof is bunching up during operation or may hang down and appear loose. Read More »
DOORS LOCKED WITH REMOTE CONTROL INSIDE THE VEHICLE. The customer states that the vehicle locks itself when the last door was closed even though the remote control/display key was inside the vehicle. Read More »
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE: Instrument Cluster (KOMBSP18) functions are intermittently inoperative including: On-board Computer (BC) button on turn signal stalk (BC button shown at left) Radio ... Read More »
ENGINE SPEED DEPENDENT NOISE DURING AUDIO PLAYBACK: Integration level updated. There is an engine speed-dependent noise heard through the speakers during audio playback. Software error in the Receiver Audio Module (RAM) control unit. Read More »
NO AUDIO IS AVAILABLE FOR APPROXIMATELY 30 SECONDS AFTER HEAD UNIT START UP: After programming vehicle no audio is available for approximately 30 seconds after head unit start-up. Read More »
KAFAS STOPS RESPONDING AND FAILS PROGRAMMING: During programming of the vehicle the session aborts or the programming fails due to the KAFAS camera (Camera-based Driver Assistance System) no longer responding. Read More »
CREASES/RIPPLES IN THE 2ND ROW 60/40 BENCH SEAT BACKREST SYNTHETIC LEATHER COVER: There are creases/ripples in the leather upholstery of the upper part of the backrest for the 2nd row of seats. This only applies to the 60/40 bench seat. Read More »
NOISE FROM FRONT SEAT HEADREST: When adjusting the headrest scissor mechanism (aka side extensions or "wings") a groaning noise can be heard. Read More »
SERVICE ACTION: REPLACE KAFAS (CAMERA-BASED DRIVER ASSISTANCE SYSTEM) CAMERA: A malfunction of the KAFAS camera can occur due to a voltage supply fault. Read More »
BUTYL ON ROOF AROUND REAR SUNROOF GLASS. CAUSE Exposure to normal ambient heat can cause the factory-applied sunroof butyl to expand and leak out from around the rear sunroof glass. Read More »
LOCKING AND UNLOCKING WITH DIGITAL KEY NO LONGER FUNCTIONS. After programming the vehicle it is suddenly not possible to unlock or lock the vehicle using the Digital Key or the Digital Key Card. Read More »
SERVICE ACTION: N63M ENGINES - CHECK AND REPLACE THE FRESH AIR INTAKE DUCT. The incorrect crankcase ventilation non return valves may have been installed in the vehicle. Read More »
IB BRAKE-BY-WIRE SYSTEM - PREFLIGHT CHECK. When starting a vehicle or driving off customers may complain of "no brake assist" or "hard brake pedal". Read More »
SERVICE ACTION: CHECK AND APPLY CAVITY PROTECTION ON DRIVER'S FRONT DOOR. Insufficient cavity protection may have been applied to the driver front door. During production insufficient cavity protection may have been applied. Read More »
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016. Read More »
DISPLAY IN THE INSTRUMENT CLUSTER OR IN HEAD-UP DISPLAY IS FLICKERING. The customer states that the display in the instrument cluster or the BMW Head-Up Display is flickering. Read More »
NO INTERIOR HEATING FUNCTION WITH REMOTE START. Customer states that when the vehicle is started using Remote Engine Start the vehicle interior does not heat up despite customer heater settings. Read More »
The following headlight CC messages are displayed: 128 "Left high beam headlight faulty" 130 "Right high beam headlight faulty" The following fault codes are stored during a vehicle test: 805A22- MLC: Communication fault timeout FLM-03 ... Read More »
Due to the semiconductor supply, the Local Interconnect Network module in either of the exterior mirrors was switched to another controller. Read More »
The incorrect Bluetooth module was installed in the headunit. Bluetooth functionality cannot be guaranteed, and mobile phones may possibly not be paired via Bluetooth. Read More »
Delivery Stop: Roof fin. BMW AG has issued a Delivery Stop (effective September 16, 2022) on a small number of Model Year 2022 - 2023 BMW vehicles that were produced on July 26, 2022. Read More »
Delivery Stop: High Beam Assistant. BMW AG has issued a Delivery Stop (effective September 16, 2022) on a small number of Model Year 2023 BMW X7 SAV vehicles that were produced between July 28, 2022 and September 2, 2022. Read More »
