Technical Service Bulletins (TSBs) for the 2015 S3 are official communications between Audi & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This bulletin provides information for when the front shock absorber cap emits cracking noises or causes spring jumps when steering or maneuvering. Read More »
This bulletin states to lightly lubricate the contact surface between the buffer stop for the shock absorber, and the front shock absorber cap to address cracking noises/spring jumps when steering or maneuvering. Read More »
THIS TECHNICAL SERVICE BULLETIN ASKS THE READER TO CHECK FOR IMPROPERLY INSTALLED OR DEFORMED FRONT SHOCK BELLOWS AND TO REPLACE IF NECESSARY. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID
This bulletin states to lightly lubricate the contact surface between the buffer stop and shock absorber cap when cracking noises/spring jumps are detected when steering or maneuvering. Read More »
This bulletin provides repair instructions for instances where creaking/squeaking noises are heard from the left front or right front area of the vehicle when being driven on uneven roads. Read More »
This bulletin provides information for when creaking/squeaking noises are heard from the left front or right front area of the vehicle when driven on uneven roads. Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
This bulletin contains repair information for when there is a creaking or squeaking noise from the front of the vehicle. This only occurs on uneven roads. Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
This technical service bulletin asks the reader to check for improperly installed or deformed front shock bellows and to replace if necessary. Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
THIS TECHNICAL SERVICE BULLETIN ASKS THE READER TO CHECK FOR IMPROPERLY INSTALLED OR DEFORMED FRONT SHOCK BELLOWS AND TO REPLACE IF NECESSARY. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
This bulletin states to lightly lubricate the contact surface between the buffer stop for the shock absorber, and the front shock absorber cap to address cracking noises/spring jumps when steering or maneuvering. Read More »
This technical service bulletin asks the reader to check for improperly installed or deformed front shock bellows and to replace if necessary. Read More »
This technical service bulletin asks the reader to check for improperly installed or deformed front shock bellows and to replace if necessary. Read More »
This bulletin contains repair instructions for when the protective sleeve for the shock absorber is out of alignment and causes a queaking or creaking noise. Read More »
THIS TECHNICAL SERVICE BULLETIN ASKS THE READER TO CHECK FOR IMPROPERLY INSTALLED OR DEFORMED FRONT SHOCK BELLOWS AND TO REPLACE IF NECESSARY. Read More »
THIS TECHNICAL SERVICE BULLETIN ASKS THE READER TO CHECK FOR IMPROPERLY INSTALLED OR DEFORMED FRONT SHOCK BELLOWS AND TO REPLACE IF NECESSARY. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
This bulletin states to lightly lubricate the contact surface between the buffer stop for the shock absorber, and the front shock absorber cap to address cracking noises/spring jumps when steering or maneuvering. Read More »
This bulletin contains repair instructions for when the protective sleeve for the shock absorber is out of alignment and causes a queaking or creaking noise. Read More »
Rear shock mounting noises. Customer may report hearing rumbling noises from the rear of the vehicle when driving on very uneven roads or over potholes. This bulletin only applies to S3 vehicles with Audi magnetic ride. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
Customer may report hearing rumbling noises from the rear of the vehicle when driving on very uneven roads or over potholes. This bulletin only applies to S3 vehicles with Audi magnetic ride. The rear shock mounts are causing the noises. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
RUNNING GEAR: AUDI MAGNETIC RIDE - KNOCKING NOISES FROM REAR SHOCKS ON S3 (8V) AND TTS (FV) BRAKE SYSTEM: BRAKING NOISES - BASIC PRINCIPALS FOR DIAGNOSIS AND REPAIR. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015. The customer may report hearing brake noise from front or rear brakes. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains a software update to correct an EPC light with one or more of the following DTCs: P039B00, P03A500, P03AF00, P03B900, P030000, P030100, P030200, P030400, and P130A00. Read More »
This bulletin contains a software update for when the MIL is on and there are one or more DTCs logged in the ECM (DTCs P030000, P030100, P030200, P030300, and/or P030400). Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE A MALFUNCTION OF THE CAMSHAFT ADJUSTER OF THE AUDI VALVELIFT SYSTEM AND TO REPLACE THE AFFECTED PART. Read More »
The customer complains of an engine droning noise or rattle noise when the engine speed is approximately 3,500 to 4,000 rpm. (Vehicle speed does not affect the noise; the vehicle can be stationary. Read More »
The customer complains of an engine droning noise or rattle noise when the engine speed is approximately 3,500 to 4,000 rpm. (Vehicle speed does not affect the noise; the vehicle can be stationary. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM. Read More »
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. Read More »
Audi of America is requesting your cooperation in supplying us with the technical information vital to the successful launch of the Audi Q3, A3 Sedan TDI, A3 cabriolet, and S3. Read More »
Audi of America is requesting your cooperation in supplying us with the technical information vital to the successful launch of the Audi Q3, A3 Sedan TDI, A3 cabriolet, and S3. Read More »
Audi of America is requesting your cooperation in supplying us with the technical information vital to the successful launch of the Audi Q3, A3 Sedan TDI, A3 cabriolet, and S3. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
Audi of America is requesting your cooperation in supplying us with the technical information vital to the successful launch of the Audi Q3, A3 Sedan TDI, A3 cabriolet, and S3. Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake ... Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, ... Read More »
This bulletin contains repair instructions for when the all wheel drive coupling is stuck on or doesn't engage without DTCs stored. Also Audi 2015 and 2016 A3 Cabriolet. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Audi of America is requesting your cooperation in supplying us with the technical information vital to the successful launch of the Audi Q3, A3 Sedan TDI, A3 cabriolet, and S3. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks ... Read More »
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
This bulletin contains instructions for correcting DTC B12251B and B102229 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
This technical service bulletin explains how to determine the status of activation keys (that affect the function of Audi drive select, cruise control, navigation, Bluetooth, smartphone interface and voice recognition), and how to update ... Read More »
This bulletin contains a software update to correct an EPC light with one or more of the following DTCs: P039B00, P03A500, P03AF00, P03B900, P030000, P030100, P030200, P030400, and P130A00. Read More »
This bulletin contains a software update to correct an EPC light with one or more of the following DTCs: P039B00, P03A500, P03AF00, P03B900, P030000, P030100, P030200, P030400, and P130A00. Read More »
This bulletin contains a software update for when the MIL is on and there are one or more DTCs logged in the ECM (DTCs P030000, P030100, P030200, P030300, and/or P030400). Read More »
RUNNING GEAR: AUDI MAGNETIC RIDE - KNOCKING NOISES FROM REAR SHOCKS ON S3 (8V) AND TTS (FV) BRAKE SYSTEM: BRAKING NOISES - BASIC PRINCIPALS FOR DIAGNOSIS AND REPAIR. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. Read More »
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. Read More »
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. Read More »
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed ... Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT
This technical service bulletin explains how to determine the status of activation keys (that affect the function of Audi drive select, cruise control, navigation, Bluetooth, smartphone interface and voice recognition), and how to update ... Read More »
This bulletin contains a software update to correct an EPC light with one or more of the following DTCs: P039B00, P03A500, P03AF00, P03B900, P030000, P030100, P030200, P030400, and P130A00. Read More »
This bulletin contains a software update to correct an EPC light with one or more of the following DTCs: P039B00, P03A500, P03AF00, P03B900, P030000, P030100, P030200, P030400, and P130A00. Read More »
This bulletin contains a software update for when the MIL is on and there are one or more DTCs logged in the ECM (DTCs P030000, P030100, P030200, P030300, and/or P030400). Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DETERMINE THE STATUS OF ACTIVATION KEYS (THAT AFFECT THE FUNCTION OF AUDI DRIVE SELECT, CRUISE CONTROL, NAVIGATION, BLUETOOTH, SMARTPHONE INTERFACE AND VOICE RECOGNITION), AND HOW TO UPDATE ... Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DETERMINE THE STATUS OF ACTIVATION KEYS (THAT AFFECT THE FUNCTION OF AUDI DRIVE SELECT, CRUISE CONTROL, NAVIGATION, BLUETOOTH, SMARTPHONE INTERFACE AND VOICE RECOGNITION), AND HOW TO UPDATE ... Read More »
The analog needles in the cluster do not always perform a full sweep when the ignition is turned on. This condition is sporadic. An error in the cluster software created the sporadic condition. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
The EPC light is illuminated. DTCs are stored in the engine control module. Due to a software error, the ECM can falsely record engine misfires in the primary detection window. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or ... Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin provides information when the all-wheel drive coupling does not work, the fuse is blown or the DTC C111204 is stored in the all-wheel drive control module. Read More »
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light ... Read More »
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake ... Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
This bulletin contains instructions for correcting DTC B12251B, B102229, and/or B102202 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
This bulletin contains instructions for correcting DTC B12251B, B102229, and/or B102202 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
This bulletin contains instructions for correcting DTC B12251B and B102229 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
This bulletin contains instructions for correcting DTC B12251B, B102229, and/or B102202 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
This bulletin contains instructions for correcting DTC B12251B, B102229, and/or B102202 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
This bulletin contains instructions for correcting DTC B12251B and B102229 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This document contains the Audi technician report. All items must be completed prior to customer delivery by an Audi technician. For A3 ONLY - Soak full body cover with water before removal (see TSB 2037319 for details). Read More »
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. Read More »
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph. Read More »
3.0T R18 Wheel: Changed to "No chains available" 3.0T R18 245/40 R18 93Y High Performance Tire: Changed Chains from 8T0091375 to "No" 3.0T R18 245/40 R18 97Y High Performance Tire: Changed Chains from 8T0091375 to "No". 3. Read More »
This bulletin advises that there is a software update available in instances where a customer reports ESC and TPMS warnings are present with DTCs B116816, and C114602. Read More »
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and ... Read More »
3.0T R18 Wheel: Changed to "No chains available" 3.0T R18 245/40 R18 93Y High Performance Tire: Changed Chains from 8T0091375 to "No" 3.0T R18 245/40 R18 97Y High Performance Tire: Changed Chains from 8T0091375 to "No". 3. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
The customer complains of an engine droning noise or rattle noise when the engine speed is approximately 3,500 to 4,000 rpm. (Vehicle speed does not affect the noise; the vehicle can be stationary. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI ... Read More »
This technical service bulletin explains how to determine the status of activation keys (that affect the function of Audi drive select, cruise control, navigation, Bluetooth, smartphone interface and voice recognition), and how to update ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage. Read More »
This bulletin contains a software update to correct an EPC light with one or more of the following DTCs: P039B00, P03A500, P03AF00, P03B900, P030000, P030100, P030200, P030400, and P130A00. Read More »
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward. Read More »
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has ... Read More »
This technical service bulletin explains how to determine the status of activation keys (that affect the function of Audi drive select, cruise control, navigation, Bluetooth, smartphone interface and voice recognition), and how to update ... Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DETERMINE THE STATUS OF ACTIVATION KEYS (THAT AFFECT THE FUNCTION OF AUDI DRIVE SELECT, CRUISE CONTROL, NAVIGATION, BLUETOOTH, SMARTPHONE INTERFACE AND VOICE RECOGNITION), AND HOW TO UPDATE ... Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin. Read More »
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed. Read More »
Audi of America is requesting your cooperation in supplying us with the technical information vital to the successful launch of the Audi Q3, A3 Sedan TDI, A3 cabriolet, and S3. Read More »
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. Read More »
This technical service bulletin explains how to determine the status of activation keys (that affect the function of Audi drive select, cruise control, navigation, Bluetooth, smartphone interface and voice recognition), and how to update ... Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a ... Read More »
This document contains the Audi vehicle detail report. DO NOT use accessories (radio, etc.) while performing detail, as this can discharge the battery. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS THAT VEHICLES WITH THE MIB MMI RADIO PLATFORM USE A NEW SDARS CHIPSET THAT RECEIVES RADIO PROGRAMMING FROM A DIFFERENT BAND THAN PREVIOUS PLATFORMS, WHICH MAY AFFECT THE RECEPTION. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DETERMINE THE STATUS OF ACTIVATION KEYS (THAT AFFECT THE FUNCTION OF AUDI DRIVE SELECT, CRUISE CONTROL, NAVIGATION, BLUETOOTH, SMARTPHONE INTERFACE AND VOICE RECOGNITION), AND HOW TO UPDATE ... Read More »
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. Read More »
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s). Read More »
This technical service bulletin explains how to determine the status of activation keys (that affect the function of Audi drive select, cruise control, navigation, Bluetooth, smartphone interface and voice recognition), and how to update ... Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. Read More »
This bulletin contains repair information for when there is a creaking or squeaking noise from the front of the vehicle. This only occurs on uneven roads. Read More »
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains instructions for correcting DTC B12251B and B102229 with airbag/seatbelt warning lamp or the PODs indicator light is displaying incorrectly. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DETERMINE THE STATUS OF ACTIVATION KEYS (THAT AFFECT THE FUNCTION OF AUDI DRIVE SELECT, CRUISE CONTROL, NAVIGATION, BLUETOOTH, SMARTPHONE INTERFACE AND VOICE RECOGNITION), AND HOW TO UPDATE ... Read More »
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with the Pre-Delivery Inspection Checklist (PDI). Read More »
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with the Pre-Delivery Inspection Checklist (PDI). Read More »
This document contains the Audi pre-delivery inspection checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
This document contains the Audi pre-delivery inspection checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. Read More »
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). Read More »
This document contains the Audi pre-delivery inspection checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
This document contains the Audi pre-delivery inspection checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
This document contains the Audi pre-delivery inspection. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
This document contains the Audi pre-delivery inspection. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Read More »
This document contains the Audi vehicle detail report. DO NOT use accessories (radio, etc.) while performing detail, as this can discharge the battery. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DETERMINE THE STATUS OF ACTIVATION KEYS (THAT AFFECT THE FUNCTION OF AUDI DRIVE SELECT, CRUISE CONTROL, NAVIGATION, BLUETOOTH, SMARTPHONE INTERFACE AND VOICE RECOGNITION), AND HOW TO UPDATE ... Read More »
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing. Read More »
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release ... Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Read More »
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
This bulletin provides information when there are scratches, or a coating on the cover of the instrument cluster, or particles in the housing. Read More »
This bulletin provides information when the all-wheel drive coupling does not work, the fuse is blown or the DTC C111204 is stored in the all-wheel drive control module. Read More »
