Technical Service Bulletins (TSBs) for the 2011 Q5 are official communications between Audi & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly. The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. Read More »
Supersedes Technical Service Bulletin Group 48 number 15-65 dated March 23, 2015. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Supersedes Technical Service Bulletin Group 48 number 14-57 dated January 29, 2014. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
AUDI: WHEN TURNING, THE STEERING FEELS STIFF AND OCCURS EVEN WHEN VEHICLE IS STATIONARY. INTERMEDIATE STEERING SHAFT NEEDS TO BE IMPROVED. MODEL 2008-2014 A4, A5, Q5. *PE Read More »
Supersedes Technical Service Bulletin Group 48 number 13-56 dated December 13, 2013. The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. Read More »
Supersedes Technical Service Bulletin Group 45 number 13-07 dated September 25, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-36 dated September 26, 2013. The customer complains that rattling or engine noise can be heard in the passenger compartment. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-47 dated August 2, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
AUDI: WHEN VEHICLE IS STATIONARY, THE STEERING WILL FEEL STILL WHEN TURNING AND THE STEERING SHAFT NEEDS TO BE UPDATED WITH IMPROVED INTERMEDIATE STEERING SHAFT. MODEL 2009-2014 A4, A5, A5 CAB, Q5. Read More »
The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. The steering shaft needs to be updated. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 97 number 13-35 dated March 27, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. Read More »
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
The customer complains that rattling or engine noise can be heard in the passenger compartment. The plastic sleeve of the intermediate steering shaft can slip towards the universal joint (mounting of the power steering rack), causing ... Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 48 number 13-45 dated July 10, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). Read More »
Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. Read More »
Supersedes Technical Service Bulletin Group 48 number 12 ? 24 dated May 8, 2012. The symbol for dynamic steering is illuminated in the instrument cluster. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
AUDI: CRACKING NOISES FROM FRONT AXLE. WHILE DRIVING ON UNEVEN ROADS OR WHEN TURNINGTHE STEERING WHEEL OVER THE FULL RANGE, CRACKING NOISES CAN BE HEARD COMING FROM THE FRONT AXLE. Read More »
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly. The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. Read More »
Supersedes Technical Service Bulletin Group 48 number 14-57 dated January 29, 2014. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. Read More »
Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. Read More »
This bulletin contains repair instructions for when a rattle or knocking noise is head when driving over bumps and the vehicle has 75mm hydro-bushings. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-42 dated July 8, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
The customer reports hearing a rattling or knocking noise when the car is driven over bumps or uneven road surfaces. The noise is noticed after the car has been driven for a while and is warmed-up, and when the temperature outside is warm. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Read More »
Supersedes Technical Service Bulletin Group 40 number 10-04 dated April 1, 2010. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber. As a result of a leak because the shock absorber is damaged. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit. Read More »
One or more fuel injectors may be stuck open, allowing fuel to enter the combustion chamber when the engine is hot. Drop in fuel pressure may cause delayed restart of the engine (?long crank?) and/or rough idle after startup. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-69 dated February 19, 2014. Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. Read More »
Supersedes Technical Service Bulletin Group 46 number 15-12 dated June 29, 2015. Customer may complain about brake squeak or squeal with light to moderate pedal pressure from front brakes. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-90 dated July 21, 2014. Customer may complain about brakes squeak or squeal with light to moderate pedal pressure. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-74 dated March 12, 2014. Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 40 number 14-39 dated February 13, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
The customer reports hearing a rattling or knocking noise when the car is driven over bumps or uneven road surfaces. The noise is noticed after the car has been driven for a while and is warmed-up, and when the temperature outside is warm. Read More »
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit. Read More »
AUDI: DUE TO DAMAGE ABS WHEEL SPEED SENSOR DURING PRODUCTION, SOME VEHICLES MAY EXPERIENCE STEERING WHEEL NOT LOCKING, IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. Read More »
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit. Read More »
AUDI: DUE TO DAMAGE ABS WHEEL SPEED SENSOR DURING PRODUCTION, SOME VEHICLES MAY EXPERIENCE STEERING WHEEL NOT LOCKING, IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Engine oil consumption is too high. Under certain driving conditions, internal engine pressure conditions in the 2.0 TFSI engine can negatively influence the rate of oil consumption. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-29 dated September 16, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. Read More »
AUDI: THE ENGINE WOULD HAVE A ROUGH IDLE, DIFFERENT MISFIRE FAULTS OR REDUCED PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, THAT CAUSES THE MALFUNCTION INDICATOR LAMP (MIL) ON. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. Read More »
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Read More »
AUDI: SOME VEHICLES WOULD EXPERIENCE ROUGH IDLE, DRIVING POWER REDUCED, ILLUMINATION OF MALFUNCTION INDICATOR LAMP (MIL) ON INSTRUMENT PANEL DUE TO SPECIFIC FAULT CODES PRESENCE. MODEL 2010-2013 A4, A5, A6, Q5. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-37 dated October 10, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-42 dated October 10, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine ... Read More »
Supersedes Technical Service Bulletin Group 01 number 13-24 dated August 20, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Read More »
Supersedes Technical Service Bulletin Group 24 number 12-28 dated April 24, 2012. MIL on. DTC P0234 (Turbo/Super Charger Overboost Condition) is stored in the engine control module, J623 (address word 01). No other DTCs are stored. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-73 dated March 7, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. Read More »
AUDI: THE CONNECTION OF WATER PUMP AND HOSE, ON SOME VEHICLES, LEADING TO HEATER CORE, HAS A COOLANT LEAKAGE FROM ENGINE AREA AND SEAL RING IS NOT THE CAUSE. MODEL 2009-2013 A4, A5, Q5, A6. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Read More »
Supersedes Technical Service Bulletin Group 17 number 12 - 31 dated August 30, 2012. Oil consumption measurement - Repair Authorization (CA). Read More »
MIL on. DTCs for the cam actuators are stored in ECM memory. After the activation of the cam actuator to change to the other cam profile, the pin of the actuator is pushed back in by the cam. Read More »
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference. Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-60 dated April 24, 2015. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 17 number 15-54 dated January 29, 2015. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
The MIL is on. DTCs P2440(00) and/or P2442(00) are stored in the ECM. One of the combi valves is defective or the vacuum solenoid is defective. Read More »
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00). Read More »
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-83 dated July 17, 2014. MIL on. DTCs may be stored in the engine control module (ECM). Assistance to properly diagnose a fuel pressure sensor -G247- concern. Read More »
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). Read More »
Supersedes Technical Service Bulletin Group 01 number 14-89 dated August 19, 2014. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Read More »
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Read More »
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). Read More »
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 21 number 13-16 dated July 9, 2013. The MIL is on. DTC P029900 (Negative Pressure Deviation) is stored as a static fault in the engine control module (ECM), J623 (address word 01). Read More »
As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak. Automatic transmission fluid is leaking at the sump pan gasket. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 85 number 13-17 dated May 15, 2013. DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-44 dated July 18, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
Supersedes Technical Service Bulletin Group 10 number 12-05 dated March 20, 2012. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. Read More »
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. Read More »
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. Read More »
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-01 dated May 29, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-42 dated July 11, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. Read More »
AUDI: THE CONNECTION OF WATER PUMP AND HOSE, ON SOME VEHICLES, LEADING TO HEATER CORE, HAS A COOLANT LEAKAGE FROM ENGINE AREA AND SEAL RING IS NOT THE CAUSE. MODEL 2009-2013 A4, A5, Q5, A6. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-40 dated June 17, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-36 dated April 15, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak. Read More »
Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak. Read More »
MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage is greater than 15,000 miles. Read More »
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. Read More »
The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. Read More »
Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. Read More »
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A SEAL INSIDE THE COOLANT PUMP CAN WEAR OUT AND LEAK COOLANT. THIS ALSO CAUSED THE ENGINE LIGHT TO COME ON. *RM UPDATED ON 06/27/2011. Read More »
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE ENGINE THERMOSTAT STAYS CLOSE AND MAY CAUSE THE ENGINE TO OVERHEAT. WARNING LIGHTS WILL ILLUMINATE. 2010-2011 MODELS. *RM Read More »
AUDI: UPDATE OF SERVICE SOFTWARE. THERE IS A LOW/UNEVEN ENGINE PERFORMANCE AND A LOSS OF ENGINE POWER. MODELS A4, A5, A5 CABRIOLET AND AUDI Q5 Read More »
ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
DTC P0234 (Turbo/Super Charger Overboost Condition) is stored in the engine control module, J623 (address word 01). No other DTCs are stored. Technical Background DTC P0234 can be set inadvertently by the software application. Read More »
DTC P0234 (Turbo/Super Charger Overboost Condition) is stored in the engine control module, J623 (address word 01). No other DTCs are stored. Technical Background DTC P0234 can be set inadvertently by the software application. Read More »
DTC P0234 (Turbo/Super Charger Overboost Condition) is stored in the engine control module, J623 (address word 01). No other DTCs are stored. Technical Background DTC P0234 can be set inadvertently by the software application. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. UNDER CERTAIN SPECIFIC CONDITIONS, 7 YEARS OR 70,000 MILES, WHICHEVER OCCURS FIRST, EMISSIONS CONTROL SYSTEMS WARRANTY, FOR TURBOCHARGER, HAS BEEN EXTENDED, DUE TO A MALFUNCTION. Read More »
Supersedes Technical Service Bulletin Group 21 number 13-13 dated April 4, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Read More »
Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. Read More »
Supersedes Technical Service Bulletin Group 21 number 13-12 dated April 1, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Read More »
Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. Read More »
Supersedes Technical Service Bulletin Group 21 number 13-11 dated March 6, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Read More »
Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Read More »
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints. Read More »
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Read More »
Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Read More »
Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. Read More »
Further TCM software calibration to improve shift concerns. Further ECM software calibration to improve hesitation. Hesitation concerns, Harsh downshifts when braking or harsh 1-2 upshifts. Read More »
Supersedes Technical Service Bulletin Group 19 number 13-44 dated July 18, 2013. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. Read More »
MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage is greater than 15,000 miles. Read More »
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A SEAL INSIDE THE COOLANT PUMP CAN WEAR OUT AND LEAK COOLANT. THIS ALSO CAUSED THE ENGINE LIGHT TO COME ON. *RM UPDATED ON 06/27/2011. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
For Audi 3.0 L TDI Generation 2.1 SUV vehicles repaired by the emissions modification recall, the following warranty extension is applicable. Read More »
As part of Audi's ongoing commitment to our environment, Audi is extending the Emissions Control Systems Warranty to cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 ... Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
On certain Audi vehicles with 2.0L TFSI engine, the diaphragm of the crankcase pressure regulating valve may have been damaged. Inspect and, if necessary, install a repair kit for the crankcase pressure regulating valve. Read More »
On certain Audi vehicles with 2.0L TFSI engine, the diaphragm of the crankcase pressure regulating valve may have been damaged. Inspect and, if necessary, install a repair kit for the crankcase pressure regulating valve. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
THIS BULLETIN INFORMS THE READER TO RECEIVE DIAGNOSIS OR AUTHORIZATION FROM THE TECHNICAL ASSISTANCE CENTER BEFORE REPAIRING AN ISSUE WITH THE CATALYTIC CONVERTER THAT CAUSES DTC P042000 Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
AUDI: SOME 2011-2012 AUDI VEHICLES WITH 2.0 TFSI ENGINES WILL HAVE THE WARRANTY EXTENDED FOR INTAKE MANIFOLD AND FUEL INJECTORS. 7/23/15 *TA Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake ... Read More »
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. Read More »
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak. Read More »
The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak. Read More »
The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak. Read More »
Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak. Read More »
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module. Read More »
Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC? s are present in the engine control module: Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Read More »
Audi has determined that a faulty fuel injector may cause minor misfire conditions and, in turn, cause the Malfunction Indicator Lamp (MIL) on the instrument cluster to illuminate due to the presence of specific fault codes caused by this ... Read More »
AUDI: SOME 2011-2012 AUDI VEHICLES WITH 2.0 TFSI ENGINES WILL HAVE THE WARRANTY EXTENDED FOR INTAKE MANIFOLD AND FUEL INJECTORS. 7/23/15 *TA Read More »
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20? F (-7? C), No. Read More »
Supersedes Technical Service Bulletin Group 01 number 11-32 dated October 26, 2011. The MIL is on. DTCs may be stored in the ECM. Assistance to properly diagnose a fuel pressure sensor -G247- concern. Read More »
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, ... Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 39 number 14-14 dated May 5, 2014. A squealing, howling, or whistling noise may be heard coming from under the vehicle. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak. Automatic transmission fluid is leaking at the sump pan gasket. Read More »
Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-02 dated April 26, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. Read More »
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: - DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is ... Read More »
Supersedes Technical Service Bulletin Group 37 number 13-86 dated February 6, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-67 dated September 28, 2012. Customer may report gearbox warning light on. In some cases after starting vehicle and placing into gear the vehicle would not move. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-71 dated November 8, 2012. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-54 dated June 28, 2012. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-60 dated July 30, 2012. Customer may report transmission warning lamp illuminated in instrument cluster. Read More »
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM Read More »
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM Read More »
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM Read More »
To aid in diagnosing the high-voltage (HV) battery of the Audi Q5 Hybrid, Audi of America is pleased to inform you of the release and automatic delivery of the Audi Q5 Hybrid Minimum Required Tools (MRT) Shipment. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks ... Read More »
AUDI: WHEN BRAKING, WOULD HAVE HARSH DOWNSHIFTS AND HESITATION CONCERNS AND ALSO UPSHIFTS 1-2 ARE HARSH. CALIBRATION OF SOFTWARE TO IMPROVE SHIFT CONCERNS AND HESITATION. MODELS 2011-12 A4, A4 AVANT, A5, A5 CABRIOLET, Q5. Read More »
POWER TRAIN:MANUAL TRANSMISSION:COLUMN SHIFT ASSEMBLY
Supersedes Technical Service Bulletin Group 37 number 14-42 dated August 1, 2014. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
Supersedes Technical Service Bulletin Group 37 number 14-41 dated August 1, 2014. There is no customer complaint with this concern. Transmission faults stored (DTC P1703 or U1111). Read More »
Supersedes Technical Service Bulletin Group 37 number 11-19 dated January 31, 2011. Automatic transmission fluid is leaking at the sump pan gasket. As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak. Read More »
AUDI: WHEN BRAKING, WOULD HAVE HARSH DOWNSHIFTS AND HESITATION CONCERNS AND ALSO UPSHIFTS 1-2 ARE HARSH. CALIBRATION OF SOFTWARE TO IMPROVE SHIFT CONCERNS AND HESITATION. MODELS 2011-12 A4, A4 AVANT, A5, A5 CABRIOLET, Q5. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-77 dated December 19, 2012. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-85 dated February 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-80 dated January 16, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is ... Read More »
Supersedes Technical Service Bulletin Group 37 number 14-44 dated September 26, 2014. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. New software in the TCM and ECM addresses the condition. Read More »
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. Read More »
Supersedes Technical Service Bulletin Group 37 number 14-32 dated July 1, 2014. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
Supersedes Technical Service Bulletin Group 37 number 14-22 dated May 1, 2014. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Read More »
Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. Read More »
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. Read More »
Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Read More »
AUDI: THE TRANSMISSION CONTROL MODULE SOFTWARE WOULD ILLUMINATE IN INSTRUMENT CLUSTER AND VEHICLE FAILS TO MOVE AFTER SHIFTING INTO GEAR AND NEW SOFTWARE IS NEEDED TO ADDRESS CONDITION. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-12 dated August 9, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-00 dated April 9, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
The fault occurs with ATF temperature below 60? C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-99 dated April 1, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-97 dated March 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-83 dated January 31, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-77 dated December 19, 2012. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: - DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is ... Read More »
Supersedes Technical Service Bulletin Group 37 number 13-86 dated February 6, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. Read More »
Further TCM software calibration to improve shift concerns. Further ECM software calibration to improve hesitation. Hesitation concerns, Harsh downshifts when braking or harsh 1-2 upshifts. Read More »
DTC P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM. Customer may report transmission warning lamp illuminated in instrument cluster. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-74 dated November 28, 2012. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-71 dated November 8, 2012. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Harsh downshifts when braking or harsh 1-2 upshift under acceleration. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-54 dated June 28, 2012. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-60 dated July 30, 2012. Customer may report transmission warning lamp illuminated in instrument cluster. Read More »
Harsh downshifts when braking or harsh 1-2 upshift under acceleration. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Customer may report transmission warning lamp illuminated in instrument cluster. Fault code P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. The fault occurs with ATF temperature below 60o C. Read More »
Engine oil service - filter cartridge replacement. When changing the oil filter and installing the new filter seal(s) in the oil filter housing, special attention is required. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:SEALS/GASKETS
As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak. Automatic transmission fluid is leaking at the sump pan gasket. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT
AUDI: VEHICLE HAVE ISSUES WITH IGNITION KEY CAN NOT BE REMOVED FROM IGNITION; VEHICLE IN PARK POSITION BUT UNABLE TO MOVE SHIFTER; ENGINE SWITCHED OFF BUT REMOTE CONTROL CAN NOT LOCK WITH ADVANCED KEY; PARK IS NOT RECOGNIZED ELECTRICALLY. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT
AUDI: VEHICLE HAVE ISSUES WITH IGNITION KEY CAN NOT BE REMOVED FROM IGNITION; VEHICLE IN PARK POSITION BUT UNABLE TO MOVE SHIFTER; ENGINE SWITCHED OFF BUT REMOTE CONTROL CAN NOT LOCK WITH ADVANCED KEY; PARK IS NOT RECOGNIZED ELECTRICALLY. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES
Supersedes Technical Service Bulletin Group 37 number 11-19 dated January 31, 2011. Automatic transmission fluid is leaking at the sump pan gasket. As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER
Supersedes Technical Service Bulletin Group 37 number 13-01 dated April 24, 2013. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-85 dated February 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
DTC P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM. Customer may report transmission warning lamp illuminated in instrument cluster. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 ... Read More »
This bulletin contains repair information for when the remote key has low range or the functions do not work. This is for all keys and there is no relevant DTCs stored. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-01 dated October 30, 2014. The MIL is on. DTCs may be stored in the ECM. Assistance to properly diagnose a fuel pressure sensor -G247- concern. Read More »
Supersedes Technical Service Bulletin Group 24 number 14-50 dated August 28, 2014. The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). Read More »
Supersedes Technical Service Bulletin Group 55 number 13-32 dated July 30, 2013. ?Low Oil Level? message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". Read More »
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. Read More »
Customer reports that the side assist is providing warnings when no vehicles are present. The radar is reflected from the rear wheels back to the sensors, resulting in a false side assist warning. Read More »
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-17 dated September 11, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-01 dated April 24, 2013. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-38 dated February 22, 2012. The ignition key cannot be removed even though the gear shifter is in Park (P). Read More »
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. Read More »
This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. Read More »
Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. Read More »
Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Read More »
The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. Read More »
Supersedes Technical Service Bulletin Group 85 number 13-17 dated May 15, 2013. DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Read More »
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. Read More »
Supersedes Technical Service Bulletin Group 45 number 13-07 dated September 25, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. Read More »
AUDI: SOME VEHICLES WOULD EXPERIENCE ROUGH IDLE, DRIVING POWER REDUCED, ILLUMINATION OF MALFUNCTION INDICATOR LAMP (MIL) ON INSTRUMENT PANEL DUE TO SPECIFIC FAULT CODES PRESENCE. MODEL 2010-2013 A4, A5, A6, Q5. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-35 dated October 8, 2013. During reset of the service reminder, the message ?AIR system - action required - observe test plan? appears on the ODIS tester. MIL is not illuminated. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-32 dated September 26, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth? telephone cannot be connected to the vehicle?s Infotainment system. Read More »
Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Read More »
Supersedes Technical Service Bulletin Group 96 number 12-32 dated April 27, 2012. The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the ... Read More »
Faults are stored in the engine control module (ECM). Engine shakes. Some of the Bosch ignition coils installed in the affected vehicles may fail prematurely. Read More »
The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-97 dated March 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. Read More »
It is possible that objects have been inserted into the ignition lock, which causes the slide of the ignition lock to become stuck in the rear part of the lock (S-contact position). Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: - DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is ... Read More »
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
One Daytime Running Light (DRL) intermittently flickers. One Daytime Running Light (DRL) intermittently lights up with more intensity then dims back to normal. The headlight beams still function normally. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. Read More »
The customer may claim that when adjusting the climate system temperature or air distribution that noises can be heard from the regulator motors. There may be various DTC? s stored in 08 ? Climate Control Module. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-67 dated September 28, 2012. Customer may report gearbox warning light on. In some cases after starting vehicle and placing into gear the vehicle would not move. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-74 dated November 28, 2012. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
Supersedes Technical Service Bulletin Group 37 number 12-60 dated July 30, 2012. Customer may report transmission warning lamp illuminated in instrument cluster. Read More »
Supersedes Technical Service Bulletin Group 26 number 12-10 dated March 30, 2012. MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage greater than 20,000 miles. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-69 dated March 15, 2012. Part or all of the daytime running lights do not work on vehicles with LED DRLs. Read More »
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-78 dated June 4, 2012. A ? bulb out? warning is active in the instrument cluster?s Driver Information System (DIS) display and one or both of the rear side marker lights are burnt ... Read More »
Supersedes Technical Service Bulletin Group 27 number 12-14 dated October 12, 2012. Complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. Read More »
Supersedes Technical Service Bulletin Group 48 number 12 ? 24 dated May 8, 2012. The symbol for dynamic steering is illuminated in the instrument cluster. Read More »
complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. Read More »
MIL on. DTCs for the cam actuators are stored in ECM memory. After the activation of the cam actuator to change to the other cam profile, the pin of the actuator is pushed back in by the cam. Read More »
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-49 dated April 25, 2014. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. Read More »
This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. Read More »
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. Read More »
Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). Read More »
Supersedes Technical Service Bulletin Group 87 number 12-37 dated November 16, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. Read More »
The MIL is on. DTCs P2440(00) and/or P2442(00) are stored in the ECM. One of the combi valves is defective or the vacuum solenoid is defective. Read More »
AUDI: MULTIPLE DIAGNOSTIC TROUBLE CODES (DTC), ON SOME VEHICLES, IS CLOGGING THE PARKING AID CONTROL UNIT, CAUSING IT TO NOT WORK PROPERLY. MODEL 2009-2016 Q5. *PE Read More »
Supersedes Technical Service Bulletin Group 91 number 11-08 dated August 22, 2011. The parking aid system does not work. DTCs may be logged in parking aid control unit for disruption/short circuit to ground. Read More »
Supersedes Technical Service Bulletin Group 55 number 13-30 dated May 28, 2013. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. Read More »
Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. The fault occurs with ATF temperature below 60o C. Read More »
"Ignition lock faulty" message is displayed in the driver information display with the symbol shown at right. DTCs are stored in the comfort system central control unit. Read More »
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are ... Read More »
AUDI: VEHICLE HAVE ISSUES WITH IGNITION KEY CAN NOT BE REMOVED FROM IGNITION; VEHICLE IN PARK POSITION BUT UNABLE TO MOVE SHIFTER; ENGINE SWITCHED OFF BUT REMOTE CONTROL CAN NOT LOCK WITH ADVANCED KEY; PARK IS NOT RECOGNIZED ELECTRICALLY. Read More »
The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. Read More »
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored. Read More »
Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. This occurs after the engine is started, the message "TPMS" appears briefly and then turns off. There are no DTCs stored. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the ... Read More »
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-51 dated August 18, 2014. The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with ... Read More »
Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. The fault occurs with ATF temperature below 60o C. Read More »
Audi has determined that, under specific conditions, the turbocharger could malfunction and may cause the Malfunction Indicator Lamp (MIL) on the instrument cluster to illuminate due to the presence of specific fault codes caused by this ... Read More »
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed ... Read More »
Supersedes Technical Service Bulletin Group 90 number 12-30 dated June 26, 2012. The driver information system (DIS) display screen is completely blank or appears to be all white The condition is intermittent and the DIS can function ... Read More »
Audi has determined that a faulty fuel injector may cause minor misfire conditions and, in turn, cause the Malfunction Indicator Lamp (MIL) on the instrument cluster to illuminate due to the presence of specific fault codes caused by this ... Read More »
AUDI: IN THE DRIVER INFORMATION SYSTEM (DIS) INSTRUMENT CLUSTER, A WARNING IS ACTIVATED REGARDING BULB OUT AND ONE OR BOTH REAR SIDE MARKER LIGHTS ARE BURNT OUT, DUE TO POSSIBLE DEBRIS OR MOISTURE IN TAILLIGHT HOUSING. Read More »
AUDI: INSTRUMENT CLUSTER DISPLAY ILLUMINATES WITH VEHICLE LIGHTS MALFUNCTION WHEN LIGHT BULB IS OUT. MODELS A4, AUDI Q5 (2009-12), A5 (2008-12) AND A5 CABRIOLET (2010-12). *PE Read More »
AUDI: WHEN ACTIVATED, THE INSTRUMENT CLUSTER SYSTEM DISPLAY ILLUMINATES BULB OUT WARNING, INDICATING ONE OR BOTH OF REAR MARKER SIDE LIGHTS BURNT OUT. *PE Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is ... Read More »
Supersedes Technical Service Bulletin Group 69 number 12-22 dated February 13, 2012. After the comfort system central control module, J393 (address word 05) is replaced, the control module cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 37 number 14-44 dated September 26, 2014. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. New software in the TCM and ECM addresses the condition. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
Supersedes Technical Service Bulletin Group 37 number 14-40 dated August 1, 2014. Customer may report that the transmission warning light is on. Read More »
Supersedes Technical Service Bulletin Group 37 number 14-39 dated August 1, 2014. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-71 dated March 13, 2014. The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. Read More »
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or ... Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-14 dated August 26, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-35 dated January 26, 2012. Customer may report that the transmission warning light is on. Read More »
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. Read More »
Supersedes Technical Service Bulletin Group 90 number 13-40 dated September 9, 2013. The driver information system (DIS) display screen is completely blank or appears to be all white. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 24 number 12-15 dated February 20, 2012. The MIL is on. DTCs are stored in the ECM. Both Secondary Air Combination Valves close if not activated. The software of the ECM needs to be updated. Read More »
Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-99 dated August 5, 2013. Sound system ?pops? and loses audio for a few seconds (for vehicles with base sound system). Read More »
Supersedes Technical Service Bulletin Group 90 number 12-30 dated June 26, 2012. The driver information system (DIS) display screen is completely blank or appears to be all white The condition is intermittent and the DIS can function ... Read More »
Supersedes Technical Service Bulletin Group 37 number 13-12 dated August 9, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-00 dated April 9, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
Some telephone numbers that were downloaded via Bluetooth? are stored with additional, unrelated numbers that do not appear in the contact on the customer"s cellular phone. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 01 number 13-95 dated May 13, 2013. Faults are stored in the engine control module (ECM). Engine shakes. Some of the Bosch ignition coils installed in the affected vehicles may fail prematurely. Read More »
The fault occurs with ATF temperature below 60? C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-99 dated April 1, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. Read More »
AUDI: WHEN BRAKING, WOULD HAVE HARSH DOWNSHIFTS AND HESITATION CONCERNS AND ALSO UPSHIFTS 1-2 ARE HARSH. CALIBRATION OF SOFTWARE TO IMPROVE SHIFT CONCERNS AND HESITATION. MODELS 2011-12 A4, A4 AVANT, A5, A5 CABRIOLET, Q5. Read More »
Supersedes Technical Service Bulletin Group 37 number 13-83 dated January 31, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Read More »
Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation. Read More »
Supersedes Technical Service Bulletin Group 37 number 12-77 dated December 19, 2012. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. Read More »
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: - DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is ... Read More »
Harsh downshifts when braking or harsh 1-2 upshift under acceleration. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
Harsh downshifts when braking or harsh 1-2 upshift under acceleration. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration. Further TCM software calibration to improve shift concerns. Read More »
AUDI: UPDATE OF SERVICE SOFTWARE. THERE IS A LOW/UNEVEN ENGINE PERFORMANCE AND A LOSS OF ENGINE POWER. MODELS A4, A5, A5 CABRIOLET AND AUDI Q5 Read More »
AUDI: SOFTWARE VERSION MANAGEMENT (SVM) OPERATING INSTRUCTIONS. DETAILING THE GENERAL PROCESS FOR CARRYING OUT A SOFTWARE VERSION MANAGEMENT (SVM) SOFTWARE UPDATE FOR ANY TSB OR REQUIRED VEHICLE UPDATE (RVU). Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
Customer may report transmission warning lamp illuminated in instrument cluster. Fault code P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM. Read More »
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light ... Read More »
Supersedes Technical Service Bulletin Group 94 number 12-96 dated November 1, 2012. Part or all of the daytime running lights do not work on vehicles equipped with LED daytime running lights. Read More »
TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Read More »
AUDI: ON SOME VEHICLES, EITHER RIGHT OR LEFT DAYTIME RUNNING LIGHT WOULD INTERMITTENTLY FLICKERS OR WOULD LIGHTS UP VERY BRIGHT AND DIMS BACK TO NORMAL DUE TO LED DRL CONTROL UNIT PWM OUTPUT SYSTEM VOLTAGE CHANGE. MODEL 2010-2012 Q5. Read More »
AUDI: THE VEHICLE LIGHTS MALFUNCTION MESSAGE MAY BE DISPLAYED ON THE DASHBOARD CLUSTER. THERE IS NO FAILURE. ALSO INCLUDED MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL S7 MY 2012-2014, MODEL RS7 MY 2014. Read More »
One Daytime Running Light (DRL) intermittently flickers. One Daytime Running Light (DRL) intermittently lights up with more intensity then dims back to normal. The headlight beams still function normally. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-78 dated June 4, 2012. A ? bulb out? warning is active in the instrument cluster?s Driver Information System (DIS) display and one or both of the rear side marker lights are burnt ... Read More »
Supersedes Technical Service Bulletin Group 94 number 11-52 dated October 11, 2011. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third ... Read More »
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". Read More »
Left or Right LED Daytime Running Light (DRL) intermittently flickers. Left or Right LED Daytime Running Light (DRL) intermittently lights up with more intensity then dims back to normal. The headlight beams still function normally. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake ... Read More »
Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-69 dated March 15, 2012. Part or all of the daytime running lights do not work on vehicles with LED DRLs. Read More »
AUDI: AFTER SWITCHING ON TERMINAL 15, A VOLTAGE DROP MY OCCUR DURING INITIALIZATION PERIOD. HEADLIGHTS NOT ADAPTED AND BASIC SETTING NOT COMPLETED. *PE Read More »
AUDI: DAYTIME RUNNING LIGHTS DO NOT WORK. DAYTIME RUNNING LIGHTS DO NOT WORK ON VEHICLES WITH XENON HEADLIGHTS. THE THUMB WHEEL OR OPTION FOR DAYTIME RUNNING LIGHTS IS TURNED OFF BY MISTAKE. *PE Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-95 dated October 25, 2012. A "bulb out" warning is displayed in the driver information system. One or both of the rear side marker lights (M37 and/or M38 bulbs) is burnt out. Read More »
AUDI: ON SOME VEHICLES, THE SWITCH BETWEEN REAR LID TAIL LAMP AND BUMPER, DOES NOT SWITCH OVER WHEN LID IS IN OPERATION, DUE TO PADDLE, OF REAR SILL TRIM, NOT CONTACTING OPPOSING LID LATCH POINTS, UNIFORMLY. Read More »
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. Read More »
AUDI: ON CERTAIN MODEL YEAR 2008 TO 2013 VEHICLES, DURING ADJUSTMENT OR REMOVAL, BRAKE LIGHT SENSORS BEING REPLACED ARE DAMAGED, PREVENTING PROPER ANALYSIS. *PE Read More »
Supersedes Technical Service Bulletin Group 66 number 12-20 dated April 9, 2012. A loud noise is heard when the outside mirrors are folded in or out. The noise originates in the metal spring inside the hinge area of the mirror housing. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-34 dated September 30, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-31 dated June 12, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-28 dated April 10, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. Read More »
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. Read More »
Supersedes Technical Service Bulletin Group 64 number 13-26 dated June 7, 2013. The customer may report hearing noises when operating the window or noises from inside the door when driving on rough roads. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
Supersedes Technical Service Bulletin Group 70 number 15-47 dated September 21, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
Supersedes Technical Service Bulletin Group 70 number 15-44 dated February 25, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
Supersedes Technical Service Bulletin Group 70 number 14-39 dated August 11, 2014. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
AUDI: WHEN SELECTING REVERSE GEAR, THE PICTURE OF REARVIEW CAMERA FAILS TO APPEAR, SPORADICALLY. CERTAIN MODELS, CAMERA IMAGE CAN BE RE=ACTIVATED. MODEL YEARS 2008-2013. *PE Read More »
Supersedes Technical Service Bulletin Group 66 number 13-39 dated December 9, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-38 dated November 15, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-37 dated November 4, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. Read More »
Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Read More »
Supersedes Technical Service Bulletin Group 66 number 12-23 dated August 3, 2012. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Read More »
AUDI: WHEN SELECTING REVERSE GEAR, THE PICTURE OF REARVIEW CAMERA FAILS TO APPEAR, SPORADICALLY. CERTAIN MODELS, CAMERA IMAGE CAN BE RE=ACTIVATED. MODEL YEARS 2008-2013. *PE Read More »
Supersedes Technical Service Bulletin Group 97 number 15-46 dated April 2, 2015. The rear wiper is not functioning or only functions intermittently. Read More »
The rear wiper is not functioning or only functions intermittently. Corrosion at the B538 splice of the rear wiper motor control circuit can cause an excessive voltage drop, resulting in an out of range control signal. Read More »
The customer may claim that when adjusting the climate system temperature or air distribution that noises can be heard from the regulator motors. There may be various DTC? s stored in 08 ? Climate Control Module. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:AIR HANDLER/CHAMBER, DUCTS, AND VALVES
In conjunction with the New Mexico DMV, Audi will be sending Takata airbag recall reminder notices to approximately 389 Audi owners in the State of New Mexico on March 13, 2023. Read More »
In conjunction with the Massachusetts DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,907 Audi owners in the State of Massachusetts on March 13, 2023. Read More »
In conjunction with the Colorado DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,174 Audi owners in the State of Colorado on February 13, 2023. Read More »
In conjunction with the New York DMV, Audi will be sending Takata airbag recall reminder notices to approximately 5,165 Audi owners in the State of New York on October 17, 2022. Read More »
In conjunction with the Georgia Department of Revenue - Motor Vehicle Division and Department of Driver Services, Audi sent Takata airbag recall reminder notices to approximately 565 Audi owners in the State of Puerto Rico on July 25, 2022. Read More »
In conjunction with the Georgia Department of Revenue - Motor Vehicle Division and Department of Driver Services, Audi sent Takata airbag recall reminder notices to approximately 2,616 Audi owners in the State of Georgia on June 22, 2022. Read More »
In conjunction with the California Department of Motor Vehicles (DMV), Audi sent Takata airbag recall reminder notices to approximately 12,349 Audi owners in the State of California on April 29, 2022. Read More »
In conjunction with the Alabama Law Enforcement Agency (ALEA), Audi is sending Takata airbag recall reminder notices to approximately 939 Audi owners in the State of Alabama on March 23, 2022. Read More »
In conjunction with the South Carolina Department of Public Safety, Audi is sending Takata airbag recall reminder notices to approximately 1,290 Audi owners in the state of South Carolina on January 24, 2022. Read More »
In conjunction with the Pennsylvania Department of Transportation, Audi is sending Takata airbag recall reminder notices to approximately 4,943 Audi owners in the state of Pennsylvania on January 24, 2022. Read More »
In conjunction with the Idaho DMV, Audi will be sending Takata airbag recall reminder notices to approximately 688 Audi owners in the State of Idaho on August 30, 2021. Read More »
In conjunction with the New York DMV, Audi will be sending Takata airbag recall reminder notices to approximately 6,957 Audi owners in the State of New York on June 21, 2021. Read More »
In conjunction with the Texas DMV, Audi will be sending Takata airbag recall reminder notices to approximately 7,185 Audi owners in the State of Texas on May 17, 2021. Read More »
In conjunction with the Michigan Department of State, Audi will be sending Takata airbag recall reminder notices to approximately 3,000 Audi owners in the State of Michigan on August 10, 2020. Read More »
In conjunction with the County of Fort Bend, Audi will be sending Takata airbag recalll reminder notices to approximately 370 Audi owners in the State of Texas on July 28, 2020. Read More »
In conjunction with the Tennessee DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,300 Audi owners in the State of Tennessee on July 7, 2020. Read More »
In conjunction with the City of Miramar, Audi sent Takata airbag recall reminder notices to approximately 89 Audi owners in the State of Florida on June 26, 2020. Read More »
In conjunction with the City of La Puente, Audi will be sending Takata airbag recall reminder notices to approximately 45 Audi owners in the State of California on June 22, 2020. Read More »
In conjunction with the Nebraska DMV, Audi will be sending Takata airbag recall reminder notices to approximately 400 Audi owners in the State of Nebraska on March 23, 2020. Read More »
In conjunction with the Ohio DMV, Audi will be sending Takata airbag recall reminder notices to approximately 4,900 Audi owners in the State of Ohio on February 10, 2020. Read More »
In conjunction with the Georgia DMV, Audi will be sending Takata airbag recall reminder notices to approximately 5,200 Audi owners in the State of Georgia on January 24, 2020. Read More »
In conjunction with the South Carolina Department of Public Safety, Audi sent Takata airbag recall reminder notices to approximately 1,800 Audi owners in the state of South Carolina on January 20, 2020. Read More »
In conjunction with the California Bureau of Automotive Repair, Audi sent Takata airbag recall reminder notices to approximately 27,300 Audi owners in the state of California on January 14, 2020. Read More »
In conjunction with the Pennsylvania DMV, Audi sent Takata airbag recall reminder notices to approximately 9,100 Audi owners in the State of Pennsylvania on November 18, 2019. Read More »
In conjunction with the Arkansas DMV, Audi will be sending Takata airbag recall reminder notices to approximately 600 Audi owners in the state of Arkansas on November 19 2019. Read More »
In conjunction with the Houston Dept. of Neighborhoods, Audi will be sending Takata airbag recall reminder notices to approximately 2,300 Audi owners in the state of Texas on November 4, 2019. Read More »
In conjunction with the Florida Dept. of Highway Safety and Motor Vehicles, Audi will be sending Takata airbag recall reminder notices to approximately 10,000 Audi owners in the state of Florida on October 14, 2019. Read More »
In conjunction with the Minnesota DMV, Audi will be sending Takata airbag recall reminder notices to approximately 3,500 Audi owners in the State of Minnesota on September 16, 2019. Read More »
In conjunction with the North Carolina DMV, Audi will be sending Takata airbag recall reminder notices to approximately 4,500 Audi owners in the State of North Carolina on August 19, 2019. Read More »
In conjunction with the Virginia DMV, Audi will be sending Takata airbag recall reminder notices to approximately 4,294 Audi owners in the State of Virginia on August 12, 2019. Read More »
In conjunction with the City of Compton, Audi will be sending Takata airbag recall reminder notices to approximately 78 Audi owners in the State of California on August 5, 2019. Read More »
In conjunction with the Commonwealth of Kentucky Transportation Cabinet, Aud will be sending Takata airbag recall reminder notices to approximately 1,476 Audi owner in the state of Kentucky on July 15, 2019. Read More »
Mailing Information: In conjunction with the Wisconsin Department of Transportation Division of Motor Vehicles (DMV), Audi will be sending Takata airbag recall reminder notices to approximately 2,877 Audi owners in the state of Wisconsin ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
Mailing Information: In conjunction with the New York Department of Motor Vehicles, Audi will be sending Takata airbag recall reminder notices to approximately 15,000 Audi owners in the State of New York on May 23, 2019. Read More »
We are approaching the changeover period where certain, current (interim remedy) airbag inflators (listed below) will be replaced by final remedy parts. Read More »
69N1, 69N2 - Campaign Parts Bulletin - Today, May 5th is the final standard weekly allocation of Takata airbag inflators. After this date, Takata allocations will be based on the previous week?s paid claim volume. Read More »
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
AUDI: SOME MODEL YEAR VEHICLES MUST HAVE THE SERVICE PART FOR THE AIRBAG CONTROL UNIT CODED AND/OR PARAMETER USING SVM CODE LISTED IN ETKA. MODELS A4, S4, A5, S5, Q5, TT, TTS, A3, PA , C6, A6 PA, D4, A8,C7 A7. Read More »
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. Read More »
AUDI: SOME MODEL YEAR VEHICLES MUST HAVE THE SERVICE PART FOR THE AIRBAG CONTROL UNIT CODED AND/OR PARAMETER USING SVM CODE LISTED IN ETKA. MODELS A4, S4, A5, S5, Q5, TT, TTS, A3, PA , C6, A6 PA, D4, A8,C7 A7. Read More »
REPLACED AIRBAG CONTROL UNIT CANNOT BE CODED. AFTER REPLACING THE AIRBAG CONTROL UNIT, THE CONTROL UNIT CANNOT BE CODED VIA SVM SPEC/ACTUAL. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
Customer may report hearing squeak or rattle sounds coming from the rear seat area. The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. Read More »
Supersedes Technical Service Bulletin Group 70 number 14-39 dated August 11, 2014. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-38 dated November 15, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. Read More »
Customer hears wind noise coming from the top of the vehicle while driving with the roof carrier bars installed. When the roof carrier bars are installed on the vehicle the acoustic environment in the cabin is predictably affected. Read More »
Supersedes Technical Service Bulletin Group 57 number 12 ? 71 dated September 17, 2012. The outer door seals have become partially detached. Read More »
AUDI: THERE IS A GAP BETWEEN BODY AND SEALING SURFACE OF DRAIN HOSE THAT ALLOWS CONDENSATION FROM EVAPORATOR TO ENTER FRONT FOOT WELL AREA DUE FAULTY AND INCORRECT INSTALLATION OF CONDENSATION DRAIN HOSE. Read More »
Supersedes Technical Service Bulletin Group 66 number 15-50 dated April 10, 2015. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-39 dated December 9, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. Read More »
Supersedes Technical Service Bulletin Group 39 number 12-12 dated June 12, 2012. A squealing, howling, or whistling noise may be heard coming from under the vehicle. Read More »
Supersedes Technical Service Bulletin Group 66 number 12-23 dated August 3, 2012. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Read More »
Wind noise is heard by the customer at highway speeds. Air flows through the exterior rear view mirror housing at the seam where the turn signal lamp meets the housing. This causes a high-frequency whistling tone. Read More »
AUDI: THERE IS A GAP BETWEEN BODY AND SEALING SURFACE OF DRAIN HOSE THAT ALLOWS CONDENSATION FROM EVAPORATOR TO ENTER FRONT FOOT WELL AREA DUE FAULTY AND INCORRECT INSTALLATION OF CONDENSATION DRAIN HOSE. Read More »
AUDI: CONDENSATION, FROM EVAPORATOR, IS ENTERING FOOTWELL AREA, IN FRONT, BETWEEN BODY AND SEALING SURFACE OF DRAIN HOSE THAT ASSEMBLED BY SUPPLIER INCORRECTLY. MODELS A4, A5 COUPE, Q5 AND A5 CABRIOLET. MY 2009-2011. Read More »
Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-80 dated November 9, 2012. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-65 dated May 14, 2012. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. Read More »
Supersedes Technical Service Bulletin Group 64 number 12-19 dated March 5, 2012. The customer may report noises when operating the window or noises from inside the door when driving on rough roads. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-48 dated July 25, 2011. Vehicle doors cannot be locked or unlocked using Advanced key. Vehicle cannot be started using the Start-Stop button. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. Read More »
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-49 dated August 8, 2011. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". Read More »
Supersedes Technical Service Bulletin Group 57 number 12-80 dated November 9, 2012. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
Supersedes Technical Service Bulletin Group 55 number 13-30 dated May 28, 2013. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. Read More »
THIS TECHNICAL SERVICE BULLETIN NOTIFIES THE READER THAT IF THE TPMS MESSAGE APPEARS BRIEFLY AFTER THE ENGINE IS STARTED AND THEN DISAPPEARS, IT DOES NOT INDICATE AN ISSUE WITH THE TPMS SYSTEM. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-38 dated July 11, 2013. Scenario A is after the engine is started, the message "TPMS" appears briefly then turns off. No DTCs are stored. Read More »
Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. The "TPMS" message is not related to a loss of tire pressure. Read More »
VOLKSWAGEN: THE MESSAGE 'TIRE PRESSURE SYSTEM MALFUNCTION' APPEARS ON THE INSTRUMENT PANEL. THERE WILL BE A STORED TROUBLE CODE. THIS PROBLEM IS LIKELY CAUSED BY SOFTWARE. *RM Read More »
AUDI: TPMS LIGHT ILLUMINATED-REPAIR AUTHORIZATION. THE TPMS WARNING LIGHT IS ILLUMINATED. NO ISSUES HAVE BEEN IDENTIFIED WITH THE ALL NEW INDIRECT TPM SYSTEM. *PE Read More »
Supersedes Technical Service Bulletin Group 48 number 13-47 dated August 2, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is ... Read More »
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. Read More »
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g. Read More »
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc. Read More »
Customer may report hearing squeak or rattle sounds coming from the rear seat area. The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. Read More »
Customer may report hearing squeak or rattle sounds coming from the rear seat area. The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. Read More »
The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when the user searches for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. Read More »
Supersedes Technical Service Bulletin Group 72 number 13-05 dated September 5, 2013. Customer may report hearing squeak or rattle sounds coming from the rear seat area. Read More »
Supersedes Technical Service Bulletin Group 72 number 12-04 dated November 30, 2012. Customer may report hearing squeak or rattle sounds coming from the rear seat area. Read More »
Supersedes Technical Service Bulletin Group 72 number 12-03 dated September 5, 2012. Customer may report squeak or rattle sounds coming from the rear seat area. Read More »
Customer may report hearing squeak or rattle sounds coming from the rear seat area. The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. Read More »
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
Supersedes Technical Service Bulletin Group 66 number 13-28 dated April 10, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Read More »
Supersedes Technical Service Bulletin Group 96 number 12-36 dated June 8, 2012. False warning from lane change assistant (Audi side assist). Read More »
AUDI: SOME VEHICLES ARE EXPERIENCING A FALSE SIDE ASSIST WARNING WHEN RADAR REFLECTS FROM BACK OF REAR WHEELS TO SENSORS AND NO OTHER VEHICLES ARE PRESENT. MODEL 2009-17 Q5. *PE Read More »
Supersedes Technical Service Bulletin Group 96 number 14-86 dated September 25, 2014. Customer reports that the side assist is providing warnings when no vehicles are present. Read More »
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
Supersedes Technical Service Bulletin Group 91 number 10 - 60 dated September 28, 2010. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the ... Read More »
AUDI: INSTRUMENT CLUSTER DISPLAY ILLUMINATES WITH VEHICLE LIGHTS MALFUNCTION WHEN LIGHT BULB IS OUT. MODELS A4, AUDI Q5 (2009-12), A5 (2008-12) AND A5 CABRIOLET (2010-12). *PE Read More »
In conjunction with the Georgia Department of Revenue - Motor Vehicle Division and Department of Driver Services, Audi sent Takata airbag recall reminder notices to approximately 565 Audi owners in the State of Puerto Rico on July 25, 2022. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill). Read More »
In conjunction with the City of La Puente, Audi will be sending Takata airbag recall reminder notices to approximately 45 Audi owners in the State of California on June 22, 2020. Read More »
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI ... Read More »
This bulletin contains instructions for verifying if there is outside influence or if the technician should carry on with standard diagnosis. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage. Read More »
This communication is issued to remind dealers of the repair validation process for repair group 19. 2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 ... Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 ... Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward. Read More »
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has ... Read More »
Supersedes Technical Service Bulletin Group 96 number 14-85 dated July 24, 2014. The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. Read More »
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin. Read More »
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed. Read More »
Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. Read More »
Supersedes Technical Service Bulletin Group 40 number 13-37 dated December 3, 2013. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-06 dated September 12, 2013. Customer reports sound system ?pops? and loses audio for a few seconds (for vehicles with base sound system) or sound system loses audio for a few ... Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Read More »
Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the ... Read More »
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. Read More »
Supersedes Technical Service Bulletin Group 01 number 13-83 dated March 29, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Read More »
The customer may claim that when adjusting the climate system temperature or air distribution that noises can be heard from the regulator motors. There may be various DTC? s stored in 08 ? Climate Control Module. Read More »
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor ... Read More »
Customer hears wind noise coming from the top of the vehicle while driving with the roof carrier bars installed. When the roof carrier bars are installed on the vehicle the acoustic environment in the cabin is predictably affected. Read More »
Supersedes Technical Service Bulletin Group 57 number 12-65 dated May 14, 2012. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. Read More »
Supersedes Technical Service Bulletin Group 64 number 12-19 dated March 5, 2012. The customer may report noises when operating the window or noises from inside the door when driving on rough roads. Read More »
Supersedes Technical Service bulletin Group 91 number 11-15 dated October 5, 2011. Customer complaint is that street addresses with hyphens (e.g. 27-80) cannot be entered as a Navigation destination. Read More »
Supersedes Technical Service Bulletin Group 94 number 12-69 dated March 15, 2012. Part or all of the daytime running lights do not work on vehicles with LED DRLs. Read More »
Supersedes Technical Service Bulletin Group 57 number 12 ? 71 dated September 17, 2012. The outer door seals have become partially detached. Read More »
AUDI: BACK UP CAMERA IMAGE IS INCORRECT OR OFF, TOO BRIGHT, TOO DARK, FUZZY, DISTORTED OR OPAQUE. MODELS AUDI Q5, Q7, A4, A5, A5 CABRIOLET (2009-14), A5, S5 (2008-14), A8 (2010-14) AND A6 (2011-14). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-28 dated March 6, 2014. MMI freezes or crashes and restarts when telephone address book is searched. Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. Read More »
The rear wiper is not functioning or only functions intermittently. Corrosion at the B538 splice of the rear wiper motor control circuit can cause an excessive voltage drop, resulting in an out of range control signal. Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 17 number 14-52 dated September 2, 2014. The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level (when measured ... Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. Read More »
Supersedes Technical Service Bulletin Group 44 number 13-38 dated July 11, 2013. Scenario A is after the engine is started, the message "TPMS" appears briefly then turns off. No DTCs are stored. Read More »
Supersedes Technical Service Bulletin Group 90 number 13-40 dated September 9, 2013. The driver information system (DIS) display screen is completely blank or appears to be all white. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 91 number 14-19 dated January 3, 2014. Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Read More »
Supersedes Technical Service Bulletin Group 91 number 10-08 dated March 18, 2010. On generation III Concert and Symphony radios , the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-08 dated August 22, 2011. The parking aid system does not work. DTCs may be logged in parking aid control unit for disruption/short circuit to ground. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a ... Read More »
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
Rough idle or reduced driving power and, in turn, an illuminated Malfunction Indicator Lamp (MIL) on the instrument cluster due to the presence of specific fault codes caused by this component. This Update is in effect until removed. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial ... Read More »
Some telephone numbers that were downloaded via Bluetooth? are stored with additional, unrelated numbers that do not appear in the contact on the customer"s cellular phone. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth?-connected phone, the phone call ... Read More »
Supersedes Technical Service Bulletin Group 96 number 13-64 dated June 20, 2013. The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the ... Read More »
Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. Read More »
Supersedes Technical Service Bulletin Group 28 number 12-19 dated May 1, 2012. The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Read More »
MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-48 dated July 25, 2011. Vehicle doors cannot be locked or unlocked using Advanced key. Vehicle cannot be started using the Start-Stop button. Read More »
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Read More »
AUDI: WHEN SELECTING REVERSE GEAR, THE PICTURE OF REARVIEW CAMERA FAILS TO APPEAR, SPORADICALLY. CERTAIN MODELS, CAMERA IMAGE CAN BE RE=ACTIVATED. MODEL YEARS 2008-2013. *PE Read More »
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The Read More »
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly ... Read More »
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). Read More »
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple? devices with the new 8-pin plug will not play videos using the Audi Music Interface. Read More »
Supersedes Technical Service Bulletin Group 91 number 09-30 dated April 14, 2009. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Read More »
Sound system "pops" and loses audio for a few seconds (for vehicles with base sound system) or sound system loses audio for a few seconds and returns on its own (for vehicles with Bose or Bang & Olufsen sound system). Read More »
Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial ... Read More »
Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-73 dated January 25, 2013. Customer complains of a "popping" noise from the radio followed by 10-15 seconds of no audio. The concern can happen in any audio source. Read More »
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. Read More »
Supersedes Technical Service Bulletin Group 91 number 10-68 dated October 26, 2010. The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected. Read More »
Supersedes Technical Service bulletin Group 91 number 11-15 dated October 5, 2011. Customer complaint is that street addresses with hyphens (e.g. 27-80) cannot be entered as a Navigation destination. Read More »
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s). Read More »
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Read More »
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. Read More »
In conjunction with the Virginia DMV, Audi will be sending Takata airbag recall reminder notices to approximately 2,026 Audi owners in the State of Virginia on July 21, 2022. Read More »
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
For Audi 3.0 L TDI Generation 2.1 SUV vehicles repaired by the emissions modification recall, the following warranty extension is applicable. Read More »
Supersedes Technical Service Bulletin Group 01 number 14-01 dated October 30, 2014. The MIL is on. DTCs may be stored in the ECM. Assistance to properly diagnose a fuel pressure sensor -G247- concern. Read More »
This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Read More »
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. Read More »
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. UNDER SPECIFIC CONDITIONS, THE EMISSIONS CONTROL SYSTEMS WARRANTY, FOR FUEL INJECTOR REPLACEMENT, HAS BEEN EXTENDED TO 10 YRS OR 120,000 MILES, WHICHEVER HAPPENS FIRST. MODEL 2009-2011. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A WARRANTY EXTENSION HAS BEEN ISSUED FOR 10 YRS OR 120, 000 MILES, WHICHEVER OCCUR FIRST, ON EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS, UNDER SPECIFIC ... Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. WARRANTY EXTENSION FOR EMISSIONS CONTROL SYSTEMS WARRANTY FOR FUEL INJECTOR REPLACEMENT, HAS BEEN ISSUED, UNDER SPECIFIC CONDITIONS, 10 YEARS OR 120,000 MILES, WHICHEVER FIRST OCCURS. Read More »
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. Read More »
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). Read More »
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. Read More »
Supersedes Technical Service Bulletin Group 37 number 11-20 dated May 13, 2011. There is no customer complaint with this concern. DTCs may be stored. Read More »
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options. Read More »
The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. Read More »
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This bulletin explains the extended warranty for the timing chain/timing chain tensioner in certain vehicles. Was revised on 11/13/18 to include a proration table for consequential damage repair reimbursement. Read More »
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 91 number 14-30 dated April 7, 2014. On generation III Concert and Symphony radios, the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence. Read More »
Supersedes Technical Service Bulletin Group 91 number 13-87 dated June 19, 2013. The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected. Read More »
Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. Read More »
Supersedes Technical Service Bulletin Group 91 number 09-30 dated April 14, 2009. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. Read More »
Supersedes Technical Service Bulletin Group 57 number 13-87 dated March 27, 2013. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. Read More »
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. Read More »
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. MIL is not illuminated. Read More »
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release ... Read More »
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options. Read More »
Supersedes Technical Service Bulletin Group 85 number 12 ? 08 dated August 17, 2012. Customer may report the front of the passenger floor mat is wet after heavy rains. Read More »
AUDI: BACK UP CAMERA IMAGE IS INCORRECT OR OFF, TOO BRIGHT, TOO DARK, FUZZY, DISTORTED OR OPAQUE. MODELS AUDI Q5, Q7, A4, A5, A5 CABRIOLET (2009-14), A5, S5 (2008-14), A8 (2010-14) AND A6 (2011-14). Read More »
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, ... Read More »
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan. Read More »
Supersedes Technical Service Bulletin Group 87 number 14-49 dated April 25, 2014. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered ... Read More »
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. Read More »
Supersedes Technical Service Bulletin Group 85 number 14-20 dated February 24, 2014. DTCs may be stored in the heating and air conditioning electronics control module. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. Read More »
Customer may report poor A/C performance or that A/C is inoperative. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-44 dated August 26, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. Read More »
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-43 dated July 12, 2013. Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. Read More »
Supersedes Technical Service Bulletin Group 87 number 13-42 dated June 11, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Supersedes Technical Service Bulletin Group 87 number 12-37 dated November 16, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Read More »
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing ... Read More »
Supersedes Technical Service Bulletin Group 64 number 12-25 dated November 7, 2012. The customer may report hearing noises when operating the window or noises from inside the door when driving on rough roads. Read More »
In conjunction with the South Carolina Department of Public Safety, Audi is sending Takata airbag recall reminder notices to approximately 1,121 Audi owners in the state of South Carolina on September 19, 2022. Read More »
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof. Read More »
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. UNDER SPECIFIC CONDITIONS, THE EMISSIONS CONTROL SYSTEMS WARRANTY, FOR FUEL INJECTOR REPLACEMENT, HAS BEEN EXTENDED TO 10 YRS OR 120,000 MILES, WHICHEVER HAPPENS FIRST. MODEL 2009-2011. Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A WARRANTY EXTENSION HAS BEEN ISSUED FOR 10 YRS OR 120, 000 MILES, WHICHEVER OCCUR FIRST, ON EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS, UNDER SPECIFIC ... Read More »
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. WARRANTY EXTENSION FOR EMISSIONS CONTROL SYSTEMS WARRANTY FOR FUEL INJECTOR REPLACEMENT, HAS BEEN ISSUED, UNDER SPECIFIC CONDITIONS, 10 YEARS OR 120,000 MILES, WHICHEVER FIRST OCCURS. Read More »
Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. The fault occurs with ATF temperature below 60o C. Read More »
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. Read More »
The fault occurs with ATF temperature below 60? C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. Read More »
The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. Read More »
The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. Read More »
Further TCM software calibration to improve shift concerns. Further ECM software calibration to improve hesitation. Hesitation concerns, Harsh downshifts when braking or harsh 1-2 upshifts. Read More »
AUDI: CRACKING NOISES FROM FRONT AXLE. WHILE DRIVING ON UNEVEN ROADS OR WHEN TURNINGTHE STEERING WHEEL OVER THE FULL RANGE, CRACKING NOISES CAN BE HEARD COMING FROM THE FRONT AXLE. Read More »
