Technical Service Bulletins (TSBs) for the 2021 A6 allroad are official communications between Audi & their dealerships that describe processes for troubleshooting or fixing certain common problems.
All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
This bulletin contains repair instructions for when the customer opens the rear lid with standing water on the vehicle after a rain or car wash the residual water splashes into the cargo area. Read More »
This bulletin provides information for when the yellow steering malfunction light is on in the cluster and DTC C110DF0 is stored in the active steering module. Read More »
This bulletin provides information to address a creaking noise from the floor area which may be generated during strong braking or steering maneuvers. Read More »
The steering warning lamp may light up in the instrument cluster with a steering fault due to a software issue. This bulletin describes the steps to perform the update. Read More »
This bulletin provides instructions to update software to address a steering malfunction warning in the instrument cluster with DTC B200FF0 or C12A329. Read More »
The steering warning lamp may light up in the instrument cluster with a steering fault due to a software issue. This bulletin describes the steps to perform the update. Read More »
This bulletin describes various DTCs stored relating to the power steering module that is the result of oxidation, and the associated repair. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This bulletin provides information when DTCs B200FF0, B200FF1, B200FF3, or B200FF4, B200FF5 are stored in the J775 suspension control unit. Read More »
This bulletin provides information for when the messages "Air suspension: system fault" or "Shock absorber system/suspension" is shown in the instrument cluster, and one or more of the following DTCs are stored B200FF0, B200FF1, B200FF3, ... Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle is driven over bumps. Read More »
This bulletin provides information when there is an air suspension malfunction warning in the cluster; DTC C1260F0n or U112100 is stored in the suspension control module. Read More »
This bulletin provides information for when an unexpected Audi presense front intervention such as a front end warning, a warning jolt, partial braking, or emergency braking occurs and a warning appears in the instrument cluster and ... Read More »
This bulletin provides instructions for when the customer is concerned about unexpected Audi pre sense front intervention such as an Audi pre sense front warning, front warning jolt, front partial braking, or an audi pre sense emergency ... Read More »
This bulletin provides information to address a creaking noise from the floor area which may be generated during strong braking or steering maneuvers. Read More »
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29. Read More »
This bulletin provides information for when the central locking/parking brake warning, or alarm sounds, or if there are exterior mirror issues. DTCs B122D29, U122800, and/or B14FF29 may be stored. Read More »
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference. Read More »
This bulletin advises of an improved sensor to address when the air conditioning system does not cool the cabin and DTCs P053000 and/or P251500 is present. Read More »
This bulletin advises that techs should document the specific o-ring seal that is replaced if a refrigerant leak is found and caused by the o-ring seal. Read More »
This bulletin describes the proper details the steps to identify and directs to repair steps to replace parts in the instance where a broken valve spring has been diagnosed. Read More »
This bulletin contains instructions for documenting the "Please reduce Oil Level" message in the instrument cluster potentially with an Engine Warmup request. Read More »
This bulletin provides information for when there is a 48V electrical system warning; DTC P0CA700, U046900 is stored in the starter/generator control module/ECM. Read More »
This bulletin advises that a small amount of coolant loss is normal. Otherwise, clean and visually inspect the coolant system in the presence of a small leak to verify if a repair is needed, and then to repair a component if it is ... Read More »
This bulletin describes various conditions that may have arisen due to a leak in the corrugated windshield washer hose, and the associated repair. Read More »
This bulletin provides information for when an EPCO warning and a fuel system warning are displayed in the instrument cluster with DTC B10581B. Read More »
This bulletin advises how to identify and repair instances where a vehicle may stops due to a lack of fuel while the fuel gauge shows 1/4 tank or more of fuel. Read More »
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP
This bulletin contains three different repair scenarios for when DTC P17F900 is stored in the TCM with symptom code 22345 and there is a gearbox malfunction message. Read More »
This bulletin provides information when there is an air suspension malfunction warning in the cluster; DTC C1260F0n or U112100 is stored in the suspension control module. Read More »
This bulletin provides information for when the message "Electrical system: fault" is in the instrument cluster - event memory B200094 (00C4). Read More »
This bulletin provides information for when the warning "Fault: Limited warning messages" appears in the instrument cluster with DTC B174404. Read More »
This bulletin provides information for when there is a 48V electrical system warning; DTC P0CA700, U046900 is stored in the starter/generator control module/ECM. Read More »
This bulletin provides information on the electronic lock (e-lock) and instructions for when the front and/or rear doors cannot be opened, fault messages are in the driver information system such as exit warning, central locking, or child ... Read More »
This bulletin provides information for when the message "Audi connect installation: error during installation" is shown in the drop down menu of the MMI. Read More »
This bulletin provides repair information for when the rear parking aid, lane change assist, or rear lid power does not work due to chafing on the wiring harness. Read More »
This bulletin provides a software update for instances where saved addresses (including the home address), favorites, last destinations, and/or icon and shortcut order are lost sporadically, the MMI screen turns blue, or becomes stuck on ... Read More »
This bulletin provides information for when the starter battery is discharged, and the vehicle cannot be started due to the front adjustment seat switch becoming jammed. Read More »
This bulletin provides the ODIS test plan for when the vehicle doesn't start, or the ignition cannot be turned on due to a drained 12V battery (A). Read More »
This bulletin contains information for when the message appears in the instrument cluster about the high beam assist and/or traffic sign detection with DTC C12B3FD. Read More »
This bulletin provides information for when the air conditioning system does not cool the cabin and DTCs P053000 and/or P251500 are present. Read More »
This bulletin provides information for when the 48V battery is in a low voltage protection state and will not accept a charge; DTC P0A7D00 is logged. Read More »
This bulletin states that it takes about 20 seconds after switching the ignition on for the Audi Pre Sense symbol advising that "Audi pre sense not available at the moment" Read More »
This bulletin provides information to address when the Audi connect "User management" screen is greyed out, and the customer cannot complete the key user pairing. OR the SOS emergency button is red or flashing read. Read More »
This bulletin describes the ways in which a variety of Audi vehicles connect to Apple Wireless CarPlay, and the methods to troubleshoot connection concerns. Read More »
This bulletin advises that if the configuration wizard in the MMI displays upon startup, the customer can either complete the configuration or deactivate via settings. Read More »
This informational bulletin states to delete the DTCs and not replace parts for when there is a malfunction message and DTC B130474 and B130574 are sporadically stored. Read More »
This bulletin contains instructions for creating a PSS record when DTC C12D5FA is stored and the driver assist systems are inoperable and a warning message is displayed. Read More »
This bulletin contains a workaround for DTC U131C00 and the HUD not turning on with "The selected system is currently unavailable" message and 12V battery might be drained periodically. Read More »
This bulletin states to replace the rear lid closing assist motor when DTC B113E29, B12E015, and/or B113E07 are present with one of the conditions. Read More »
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time ... Read More »
This bulletin contains a software update that addresses when the lane departure warning system is sporadically not available with DTC C12D7F0. Read More »
This bulletin requests that technicians create a Pending Service Solutions record in the Pending Service Solutions Database in instances where there are misfires with DTCs P0300 through P0306. Read More »
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored. Read More »
This bulletin provides information when there is a message in the instrument cluster: :Instrument cluster: fault. Limited warning messages. Please contact workshop"; B200096. Read More »
This bulletin provides information for when the warning "Fault: Limited warning messages" appears in the instrument cluster with DTC B174404. Read More »
This bulletin provides information for when the messages "Air suspension: system fault" or "Shock absorber system/suspension" is shown in the instrument cluster, and one or more of the following DTCs are stored B200FF0, B200FF1, B200FF3, ... Read More »
This bulletin provides a software update for when "All Wheel Drive Malfunction Message" is displayed in the instrument cluster and DTC U030000 is logged. Read More »
This bulletin provides information for when an EPCO warning and a fuel system warning are displayed in the instrument cluster with DTC B10581B. Read More »
This bulletin contains information for when the message appears in the instrument cluster about the high beam assist and/or traffic sign detection with DTC C12B3FD. Read More »
This bulletin provides information on when the message "Instrument cluster: fault. Limited warning messages. Please contact workshop" DTC B200096 may be stored. Read More »
This bulletin provides directions when the SOS malfunction warning is displayed in the instrument cluster accompanied by DTC B200096 or DTCB200000. Read More »
This bulletin provides instructions to update software to address a steering malfunction warning in the instrument cluster with DTC B200FF0 or C12A329. Read More »
The steering warning lamp may light up in the instrument cluster with a steering fault due to a software issue. This bulletin describes the steps to perform the update. Read More »
This bulletin states to create a PSS record when the message "SOS - Emergency call malfunction, please contact service" is displayed in the instrument cluster and DTCs B129B11 and B239C11 are stored in the control module for emergency ... Read More »
This bulletin provides instructions for when various driver assist warnings are displayed in the instrument cluster, or the intersection assist arrows flicker for a short period of time after the vehicle has been started. Read More »
The steering warning lamp may light up in the instrument cluster with a steering fault due to a software issue. This bulletin describes the steps to perform the update. Read More »
This bulletin contains information for when the messages appear in the instrument cluster about the high beam assist and/or traffic sign detection with DTC C12B3FD. Read More »
This bulletin describes a concern where the message "SAFE CP" displays in the virtual cockpit and recommends a software update to resolve this matter. Read More »
This bulletin advises the technician to create a PSS record for when after a software update, with active privacy settings, e.g. "Use of vehicle position", the pop-up window is shown with every ignition cycle. Read More »
This informational bulletin contains instructions for when a non-plus sized iPhone heats up while wirelessly charging and the CarPlay screen may appear frozen. Read More »
This bulletin provides information for when the intersection assist arrows flicker for a short period after the vehicle has started, or various other driver assist warnings; DTCs C12D5FA, B200FF9, and/or B107A16 may be stored. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin provides information pertaining to the warning message "Front/rear parking aid: sensor view restricted because of environmental factors. No obstacle warning" accompanied by one of the following DTCS B107BF0 or B10FCF0. Read More »
This bulletin contains instructions for creating a PSS record when DTC C12D5FA is stored and the driver assist systems are inoperable and a warning message is displayed. Read More »
This bulletin contains instructions for creating a PSS record when DTC C12D5FA is stored and the driver assist systems are inoperable and a warning message is displayed. Read More »
ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY:MANAGEMENT SYSTEM/ENERGY CONTROL MODULE (BMS/BECM)
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains information for when the messages appear in the instrument cluster about the high beam assist and/or traffic sign detection with DTC C12B3FD. Read More »
This bulletin provides direction for instances where the center section of the tail lamp trim molding is pulling away from the bonding strip. Read More »
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production. Read More »
This bulletin provides information for when the central locking/parking brake warning, or alarm sounds, or if there are exterior mirror issues. DTCs B122D29, U122800, and/or B14FF29 may be stored. Read More »
This bulletin advises that the window washer pump may become blocked due to frozen washer fluid; one more more DTCs may be present: DTCs B126101, B126111, or B126113. Read More »
This bulletin requests that technicians create a record in the Pending Service Solutions database in instances where the air conditioning function favorite on the lower display is lost. Read More »
This bulletin provides information for when the air conditioning system does not cool the cabin and DTCs P053000 and/or P251500 are present. Read More »
This bulletin provides information on a software update for when saved addresses, favorites, last destinations, HVAC favorite button assignment, and/or icon and shortcut order are lost sporadically; In rare cases the screen may turn ... Read More »
This bulletin provides information on a software update for when saved addresses, favorites, last destinations, HVAC favorite button assignment, and/or icon and shortcut order are lost sporadically; In rare cases the screen may turn ... Read More »
This bulletin provides instructions for when the lower MMI display flickers sporadically, or looks distorted; HVAC settings change without user input; or touch inputs are detected on the lower display with out interaction. Read More »
This repair authorization requests that technicians contact the Technical Assistance Center in instances where the Airbag warning lamp is on, DTC B101704, B103604. Read More »
This informational bulletin states to delete the DTCs and not replace parts for when there is a malfunction message and DTC B130474 and B130574 are sporadically stored. Read More »
This informational bulletin states to delete the DTCs and not replace parts for when there is a malfunction message and DTC B130474 and B130574 are sporadically stored. Read More »
This informational bulletin states to delete the DTCs and not replace parts for when there is a malfunction message and DTC B130474 and B130574 are sporadically stored. Read More »
This bulletin provides information for when there is a seat belt warning, or a pre-sense warning that appears sporadically while driving; DTC B101C07 is stored in the airbag module. Read More »
This informational bulletin states to delete the DTCs and not replace parts for when there is a malfunction message and DTC B130474 and B130574 are sporadically stored. Read More »
This bulletin provides information when the rear lid is not closing fully, rear lid lock not engaging in the secondary latch position, DTC B113E29, and B12E015. Read More »
This bulletin provides information for when the luggage compartment lid cannot be closed using the button(s) in the luggage compartment trim. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
Due to a manufacturing discrepancy, it may only be possible to lock the seat backrest back in place (when restoring it to an upright position) by exerting more force than usual. Read More »
Due to a manufacturing discrepancy, it may only be possible to lock the seat backrest back in place (when restoring it to an upright position) by exerting more force than usual. Read More »
This bulletin provides instructions for when the Audi virtual cockpit display remains blank when the driver's door is opened and the driver enters the vehicle. Read More »
This bulletin contains diagnosis information for when the front and/or rear doors cannot be opened and there maybe be various DTCs associated. Read More »
This bulletin provides information for when the rear lid does not close fully, and the rear lid lock does not engage the secondary latch position; DTCs DTC B113E29, B12E015, B113E07. Read More »
This bulletin provides information when the power rear lid cannot be opened; DTC B113E07 and/or B113E29 are stored in the rear lid electronics module. Read More »
This bulletin provides information for when the luggage compartment lid cannot be closed using the button(s) in the luggage compartment trim. Read More »
This bulletin provides information on the electronic lock (e-lock) and instructions for when the front and/or rear doors cannot be opened, fault messages are in the driver information system such as exit warning, central locking, or child ... Read More »
This bulletin states to replace the rear lid closing assist motor when DTC B113E29, B12E015, and/or B113E07 are present with one of the conditions. Read More »
Due to a manufacturing discrepancy, it may only be possible to lock the seat backrest back in place (when restoring it to an upright position) by exerting more force than usual. Read More »
This bulletin provides information when the front or rear door lock is not locking, is without function, and/or fault messages in DIS, DTC(s) B122D29, B14FF29 or B122B13. Read More »
This bulletin contains diagnosis information for when the front and/or rear doors cannot be opened and there may be various DTCs associated. Read More »
This bulletin contains diagnosis information for when the front and/or rear doors cannot be opened and there maybe be various DTCs associated. Read More »
This bulletin contains diagnosis information for when the front and/or rear doors cannot be opened and there maybe be various DTCs associated. Read More »
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph. Read More »
This bulletin provides information for when the DTC C12D5FA is stored; Audi adaptive light, Audi pre sense fault, and Audi cruise assist inoperable. Read More »
This bulletin provides information for when there is a TPMS message in the instrument cluster, or the TPMS light is on, and DTC U012700 is stored in the data bus control module. Read More »
All models except Q3, R8, and TT: Settings Section: Split Verify and set language & measurements checklist items into 2 separate with instructions. Read More »
This bulletin contains repair instructions for noises when in reverse or vibrations/humming/droning or rubbing when fully turning the wheel. Read More »
This bulletin requests that technicians create a record in the Pending Service Solutions database in instances where there is noise from the backrest of the front seat. Read More »
This bulletin provides information for when the starter battery is discharged, and the vehicle cannot be started due to the front adjustment seat switch becoming jammed. Read More »
Due to a manufacturing discrepancy, it may only be possible to lock the seat backrest back in place (when restoring it to an upright position) by exerting more force than usual. Read More »
Due to a manufacturing discrepancy, it may only be possible to lock the seat backrest back in place (when restoring it to an upright position) by exerting more force than usual. Read More »
Due to a manufacturing discrepancy, it may only be possible to lock the seat backrest back in place (when restoring it to an upright position) by exerting more force than usual. Read More »
This Pending service solutions requests that technicians create a PSS record for instances where a yellow check engine lamp is intermittently displayed upon start with DTC U014000or U110100 is sporadically stored. Read More »
This bulletin states to create a PSS record for when the star button is programmed to the front camera views and is lost after a bus sleep cycle. Read More »
This bulletin provides information for when an unexpected Audi presense front intervention such as a front end warning, a warning jolt, partial braking, or emergency braking occurs and a warning appears in the instrument cluster and ... Read More »
This bulletin contains instructions for creating a PSS record when DTC C12D5FA is stored and the driver assist systems are inoperable and a warning message is displayed. Read More »
This bulletin provides repair information for when the rear parking aid, lane change assist, or rear lid power does not work due to chafing on the wiring harness. Read More »
This bulletin provides instructions for when the lane change assist/intersection assist is sporadically not working and DTC B200FF9 is present in either the lane change assist control modules, or the corner radar control modules. Read More »
This bulletin provides information for when the intersection assist arrows flicker for a short period after the vehicle has started, or various other driver assist warnings; DTCs C12D5FA, B200FF9, and/or B107A16 may be stored. Read More »
All models except Q3, R8, and TT: Settings Section: Split Verify and set language & measurements checklist items into 2 separate with instructions. Read More »
This bulletin provides information for when the individual overhead view cameras are inoperative, the picture is blurry or fogged up, DTCs B200FFA, B127C04, C12AE02. Read More »
This bulletin provides information for when the intersection assist arrows flicker for a short period after the vehicle has started, or various other driver assist warnings; DTCs C12D5FA, B200FF9, and/or B107A16 may be stored. Read More »
This bulletin contains repair instructions for when one of the following DTCs is logged B127C04, B127D04, B127E04, B127F04, and B200FFA with a fogged overhead camera. Read More »
This bulletin states to create a PSS record for when the star button is programmed to the front camera views and is lost after a bus sleep cycle. Read More »
This bulletin provides instructions for when the Audi virtual cockpit display remains blank when the driver's door is opened and the driver enters the vehicle. Read More »
This bulletin states that it takes about 20 seconds after switching the ignition on for the Audi Pre Sense symbol advising that "Audi pre sense not available at the moment" Read More »
This bulletin contains instructions for when the head up display cannot be turned on, and the message "the selected system is currently unavailable" is displayed periodically on the MMI display. The 12v battery may be drained. Read More »
This bulletin provides instructions for when a customer states that after an over-the-air navigation map update the navigation system is permanently initializing or the navigation map is incomplete or corrupt and DTC B126CF0 and/or ... Read More »
This bulletin provides information for when the message "Audi connect installation: error during installation" is shown in the drop down menu of the MMI. Read More »
This bulletin provides a software update for instances where saved addresses (including the home address), favorites, last destinations, and/or icon and shortcut order are lost sporadically, the MMI screen turns blue, or becomes stuck on ... Read More »
This bulletin provides information for when the headlamp washer nozzle/pressure cylinder does not retract automatically after a wash cycle. Read More »
This bulletin provides information to address when the Audi connect "User management" screen is greyed out, and the customer cannot complete the key user pairing. OR the SOS emergency button is red or flashing read. Read More »
This bulletin describes the ways in which a variety of Audi vehicles connect to Apple Wireless CarPlay, and the methods to troubleshoot connection concerns. Read More »
This bulletin provides direction for instances where the center section of the tail lamp trim molding is pulling away from the bonding strip. Read More »
This bulletin advises that techs should document the specific o-ring seal that is replaced if a refrigerant leak is found and caused by the o-ring seal. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This bulletin describes an error which may arise due to a bug in the software of a customer's phone, which causes the Apple CarPlay screen to appear blank, and for audio drop-outs. Read More »
This bulletin describes a concern where the message "SAFE CP" displays in the virtual cockpit and recommends a software update to resolve this matter. Read More »
This bulletin states to replace the rear lid closing assist motor when DTC B113E29, B12E015, and/or B113E07 are present with one of the conditions. Read More »
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. Read More »
This informational bulletin contains instructions for when a non-plus sized iPhone heats up while wirelessly charging and the CarPlay screen may appear frozen. Read More »
Due to a manufacturing discrepancy, it may only be possible to lock the seat backrest back in place (when restoring it to an upright position) by exerting more force than usual. Read More »
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). Read More »
This Pending Service Solution (PSS) requests that technicians create a record in the PSS database in instances where the star button function assignment is lost on the multifunction steering wheel is lost sporadically. Read More »
This bulletin provides information for when there is a function restriction with event memory entry P071800 - P276800 (symptom 20736 - 20737). Read More »
This bulletin provides information for when high beam assist or traffic sign detection limited, DTC 12B3FD may be stored in the DAS control module. Read More »
This bulletin provides information related to maintaining the 12V Lead-acid or AGM battery when a vehicle is parked for a prolonged period of time. Read More »
This bulletin provides information on a software update for when saved addresses, favorites, last destinations, HVAC favorite button assignment, and/or icon and shortcut order are lost sporadically; In rare cases the screen may turn ... Read More »
This bulletin provides information on a software update for when saved addresses, favorites, last destinations, HVAC favorite button assignment, and/or icon and shortcut order are lost sporadically; In rare cases the screen may turn ... Read More »
This bulletin provides instructions for when the Audi connect "User management" option is greyed out, or the SOS emergency button is red or flashing red. Read More »
This bulletin provides instructions for when there is water discovered in the footwell area and electrical connectors may be showing signs of corrosion. Read More »
This bulletin advises to create a PSS record in instances where information in the MMI such as last destinations, favorites, and user defined buttons are lost. Read More »
The message "SOS Malfunction - Emergency call malfunction, please contact service" may appear erroneously in the presence of DTCs B129B11 and/or DTC B239C11. No repairs are necessary at this time. Read More »
This bulletin states to create a PSS record for when the star button is programmed to the front camera views and is lost after a bus sleep cycle. Read More »
This bulletin describes an error which may arise due to a bug in the software of a customer's phone, which causes the Apple CarPlay screen to appear blank, and for audio drop-outs. Read More »
This bulletin states to create a PSS provides a workaround to address a concern when last destinations, favorites, and home/work addresses are sporadically lost. Read More »
This bulletin contains instructions for submitting a customer registration form for the Audi phone box to the customer's Mobile Network Operator. Read More »
This Pending Service Solution (PSS) requests that a record be added to the PSS database in instances where the radio favorites are lost, shortcuts are greyed out on lower screen with MIB3 vehicles. Read More »
All models except Q3, R8, and TT: Settings Section: Split Verify and set language & measurements checklist items into 2 separate with instructions. Read More »
This bulletin provides information for when Apple CarPlay pops up or takes over audio without user intervention in vehicles with the Audi Smartphone Interface. Read More »
This bulletin provides information for when there is a TPMS message in the instrument cluster, or the TPMS light is on, and DTC U012700 is stored in the data bus control module. Read More »
This bulletin provides a software update for instances where saved addresses (including the home address), favorites, last destinations, and/or icon and shortcut order are lost sporadically, the MMI screen turns blue, or becomes stuck on ... Read More »
This bulletin provides instructions for a software update in cases when "SAFE CP" is displayed in the center of the screen of the Audi virtual cockpit, the gauges function normally, and DTC B200FF0 may be stored. Read More »
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s). Read More »
This bulletin describes an error which may arise due to a bug in the software of a customer's phone, which causes the Apple CarPlay screen to appear blank, and for audio drop-outs. Read More »
This bulletin describes an error which may arise due to a bug in the software of a customer's phone, which causes the Apple CarPlay screen to appear blank, and for audio drop-outs. Read More »
This bulletin describes the registering and pairing process required to utilize the SIM card to activate 3rd generation Audi connect services. Read More »
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs. Read More »
This bulletin advises that the message "CNG inspection" or "CNG mode active" with no relevant DTCs is currently being investigated. Techs should create a PSS record when this concern is reported by a customer. Read More »
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again. Read More »
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning. Read More »
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly. Read More »
This bulletin provides information when there are scratches, or a coating on the cover of the instrument cluster, or particles in the housing. Read More »
This Pending Service Solution (PSS) requests that technicians enter a record into the PSS Database in instances where there is noise from the backrest of the front seat. Read More »
Air suspension warning - DTC P089200 charge handle doesn't release vehicle will not charge Corrosion on wheelhouse cover plate P008700 - low fuel pressure U060B00 - no com to G31 boost pressure sensor Airbag light on, DTCs B101704, ... Read More »
This Pending Service Solution (PSS) requests that technicians create a PSS Database record in instances where the radio favorites are lost/shortcuts are greyed out in vehicles with MIB3. Read More »
This bulletin provides information for when the rear lid does not close fully, and the rear lid lock does not engage the secondary latch position; DTCs DTC B113E29, B12E015, B113E07. Read More »
This bulletin provides information when the power rear lid cannot be opened; DTC B113E07 and/or B113E29 are stored in the rear lid electronics module. Read More »
This bulletin provides information when the front or rear door lock is not locking, is without function, and/or fault messages in DIS, DTC(s) B122D29, B14FF29 or B122B13. Read More »
This bulletin provides information for when there is a function restriction with event memory entry P071800 - P276800 (symptom 20736 - 20737). Read More »
This bulletin provides information for when the message "Electrical system: fault" is in the instrument cluster - event memory B200094 (00C4). Read More »
This bulletin contains diagnosis information for when the front and/or rear doors cannot be opened and there may be various DTCs associated. Read More »
This Pending service solutions requests that technicians create a PSS record for instances where a yellow check engine lamp is intermittently displayed upon start with DTC U014000or U110100 is sporadically stored. Read More »
